Search Documents

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By R. L. Bruening, N. E. Izatt, S. R. Izatt

"Rare earth elements (REE) are essential and unique components of many high-technology products without which functioning of modern society would be greatly impaired. Commercial deposits of REE are limited to a few geographical locations. Largely untapped sources of REE are available in endof- life (EOL) magnets, rechargeable batteries, and electronics. Presently, < 1% of REE in EOL wastes is recycled. Conversion of EOL wastes to liquid streams allows use of IBC’s Molecular Recognition Technology (MRT) process to selectively recover, separate, and purify target REE and associated metals at g/L to mg/L or lower concentration levels. The MRT process together with its applications to separations of REE and associated metals in recycling as well as in mining are described. Economic and environmental advantages of MRT are presented. INTRODUCTIONRare earth elements (REE) include the lanthanide series (La-Lu), Y, and Sc. These elements are not rare, but concentrated minable deposits are scarce (Cordier 2012; Haxel, Hedrick, & Orris, 2002). Over 95 % of the world’s supply of REE is controlled by China (Hanson, 2011a) where they are mined, processed, and the pure elements incorporated into a growing number of consumer and military products. The consumer products are marketed worldwide. Since REE are vitally important in consumer and military products, this situation has caused other nations to scramble to develop the capability to produce their own supply (Cordier, 2012).In the U. S., Molycorp has reopened the Mountain Pass REE mine in California and production has begun (Goldenberg, 2010). Development of a reliable internal source of REE is of high national priority in the U.S. (Hanson, 2011b; Hess, 2012: “Obama Announces”, 2012). These elements have in recent decades been incorporated into new consumer and military products that are essential to our economy and defense. These products range from wind turbines, high performance magnets, hybrid car rechargeable batteries, energy efficient lighting electronics, flat screen televisions, and smart phones to advanced weapons systems (Haxel et al., 2002; Levkowitz & Beauchamp-Mustafaga, 2010)."

Jan 1, 2012

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few ? but very important ? instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By A. Bezama

For over a decade European countries have addressed contaminated sites by developing technologies for managing both polluted soil and groundwater. This development has not only been driven by health and environmental aspects, but also because of economic pressures, as the remediation and redevelopment of derelict areas can be a meaningful alternative to undeveloped areas for the establishment of new industrial, recreational, housing and service locations. In most developing countries, however, the subject of contaminated sites is a new environmental issue that authorities have recently started to deal with. Among these countries, Chile has just started to prepare the country&apos;s legal context as well as to foster the formation of research and investigation groups that will deal with the exploration, investigation and management of contaminated sites. That requires a comprehensive technical, scientific and legal support in this stage. Goal of this article is to present the state-of-the-art technologies for site remediation currently applied in industrialized countries, in order to identify the most interesting approaches that can be implemented within the Chilean situation, especially considering the influence of the copper mining industry on the soil and groundwater quality of the environment surrounding their production facilities.

Jan 1, 2007

By J. F. Wright

During the last three years prospecting has been active in southeastern Manitoba and a number of interesting gold, nickel and copper deposits have been discovered within an area 90 miles north of the international boundary, and extending about 40 miles westerly from between mileage 60 and 110 on the Manitoba-Ontario boundary. As known at present, two-thirds of this area of 2,000 square miles is underlain by pre Cambrian granite and granite gneiss and is not likely to contain mineral deposits of economic importance. The remaining one-third is underlain by metamorphosed sediments and lavas (greenstones), penetrated by the granite and granite gneiss and, at various localities, cut by bosses, sills, or dykes of gabbro, diorite, granodiorite, and other types of intrusives. The nickel, copper, and gold mineralization accompanied or followed the intrusion of these different rock types. The gold deposits are limited in distribution, so far as known, to the northern part of this prospecting area and occur along Manigotagan and Wanipigow rivers. These deposits have recently been described in some detail, (3) and therefore only the copper and copper-nickel deposits of the southern part of this area, along Oiseau and Maskwa rivers, will be described in this paper.

Jan 1, 1925

By J. E. Dutrizac

Mercury balances have been obtained for the flotation circuits at Pamour Porcupine Mines, Timmins, Ontario, and at Brunswick Mining and Smelting Corporation, Bathurst, New Brunswick. The mineral form of mercury in both deposits has been ascertained. At Pamour Porcupine, the mercury is approximately evenly divided among sphalerite, native silverelectrum and tetrahedrite-tennantite; at Brunswick Mining, this element is contained mostly in the sphalerite, although tetrahedrite (and possibly pyrite) also contains minor quantities.

Jan 1, 1979

By M. A. Kessick

Current treatment and disposal procedures are compared for clay slimes resulting from the extraction of Alberta oil sands, the extraction of Florida phosphate matrix, the recovery of diamonds from kimberlite deposits in South Africa, the recovery of kaolin from clay deposits in southwest England and the upgrading of bauxite ore. Published research in the area is reviewed, and common trends which are emerging in the disposal of clay slimes are discussed.

Jan 1, 1978

By N. Razavinia

Most mining and metallurgical industries produce relatively large quantities of low grade waste heat which they vent, for the most part, to the environment. To date, little is being done to recover some of this heat and transform it from low grade to a high grade energy form such as electricity. A few decades back this was also true of paper, plastics and metals. Recycling was not a prominent activity. Today, we all know that it is and that recycling is a must for sustainable development. To this end, we feel that we are now at that point in time when the recycling of waste heat to electricity must be given serious consideration. By recycling waste heat one can achieve at least one if not two of the following benefits: 1) reduction in the carbon footprint ? by improving the overall energy efficiency of a process, and 2) production of electricity at an economically viable cost. We have developed a process that captures, concentrates and converts (3 C?s) waste heat to electricity. The process comprises 3 distinct interacting units. The first unit captures and concentrates waste heat using heat pipe technology. The second unit converts some of the concentrated heat to mechanical work which can then be readily converted to electricity. This unit is based on the classical piston/cylinder engine arrangement that is widely used by consumers to power systems with compressed air, for example. The third unit of the process dissipates the heat that the engine cannot convert to high grade energy. It also uses heat pipe technology to achieve this. The combination of the 3 units forms a unique system for recycling waste heat. This paper describes the system and it presents some results that show how the system can be made to be economically viable.

Aug 1, 2013

By F. J. Alcock

IN the summer of 1934, gold was discovered on Lodge bay, on the north shore of lake Athabaska in northern Saskatchewan, about fifty miles east of the Alberta boundary line. The first claims were taken up by the Consolidated Mining and Smelting Company of Canada, Limited, and there was a &apos;rush&apos; to locate similar showings. Staking continued through the summer and succeeding winter, and in the spring of 1935 the provincial government established a recording office at a convenient point which is central to the more important holdings and where &apos;planes can land in any weather. During the past summer, the name of this townsite was changed from Beaverlodge to Goldfields, and a post office was established here. The season was one of great activity; a great deal of assessment and development work was carried out and a large amount of further prospecting done. In addition to the work by private companies, geological investigation was carried out in the region by a Federal Geological Survey party under the charge of the writer and a reconnaissance examination was made of an area of some 7,000 square miles surrounding the region of particular interest. Though this was the first discovery of gold in the region it was not the first occasion that prospecting had been carried out along the north side of lake Athabaska. Over twenty years ago, a number of prospectors were at work in the area and a large number of claims were staked, many of which were never recorded. One man by the name of Piché, in the years 1910, 1912, and 1913, took up a considerable number of claims north of Pine Channel narrows, east of Fond du Lac. His discoveries, which consisted of small showings of sulphides in sedimentary gneiss, proved to be of no economic importance. In 1915, a sudden widespread interest was aroused by the report that a sample of ore collected near Fond du Lac had yielded a very high assay in silver. In March and April of that year, prospectors began to rush into the field by dog teams to take up claims, and, as soon as the Athabaska river was free of ice, others started by boat from Athabaska Landing. Some hundreds of claims were staked and recorded in the Dominion Land Office at Edmonton or at Fort Smith. By July, most of the prospectors had? left the region, having failed to find any silver ore. In 1921, considerable prominence was given to the area a few miles east of Goldfields by reports that very large masses of iron ore were available there. Claims were taken up, but the material is much too low grade to be considered commercial ore.

Jan 1, 1936

By Ralph Johnson, Philippe Gaultier, Loui Fauteux, Andrew Dasys

"This paper outlines the implementation of the Mechanic&apos;s Stethoscope from the earliest stages of development to the implementation at Brunswick Mining and Smelting. It details the cooperative efforts of personnel at Noranda Technology Centre (NTC) and Brunswick Mining & Smelting (BMS) during the technology transfer of the Mechanic&apos;s Stethoscope. It demonstrates how everyone worked toward a goal of developing a product that is accepted as a useful addition to the work environment.The Mechanic&apos;s Stethoscope is an underground vehicle diagnostic system consisting of computer hardware and software intended to assist mechanics in daily tasks. Its tools facilitate quick and easy access to any information required during the maintenance of an underground vehicle. Each tool presents vehicle condition data in a simplified manner. The additional information improves the mechanics understanding of the vehicle condition. The result is a healthier fleet of vehicles and faster diagnosis times.When introducing a computer based system into a traditionally non-computer oriented environment a concern is the acceptance of the system. This concern exists on many levels."

Jan 1, 1995

By K. J. Daun, C. J. Shi

UsiborThrough the second step heating at 900 °C, the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex-situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. 5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

Jan 1, 2015

By G. P. Kundargi

India is one of the fastest growing economies in the world. The role of the Iron & Steel industry is very important for the development of the country. Iron and steel are among the most important components required for the infrastructure development of the country. This is one of the fastest growing sectors. The demand drivers for the Indian Iron & Steel industry are increase in the activities of the manufacturing industry and infrastructure development. Indian Iron & Steel industry with its strong forward and backward linkages contributes significantly to overall growth and development of the economy. The industry today directly contributes 2% of India?s Gross Domestic Product and its weightage in the official Index of Industrial Production (IIP) is 6.2%. Manganese is a main ingredient for production of steel. Almost 90% manganese is being utilized by the steel industry worldwide. Globally, there is no substitute for manganese as on date. There is huge gap between demand and production of manganese ore in the country. To meet this demand gap and to support for growth of national economy, MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprises, producing annually around 1.1 million tonnes (mt) of manganese ore and value added products, has geared up with various infrastructural activities to increase the present production capacity of 1.1?1.5 mt in 2016?2017 and 2.2 mt in 2020?2021. The paper deals with the technological improvements and infrastructural development activities of MOIL; this will help MOIL to become the market leader in manganese ore production globally in the coming years.

Aug 1, 2013

By J. B. Watts

"THE Mine Engineering Department at Gaspe Copper is staffed by a chief engineer, assist-ant engineer, research engineer, chief surveyor, four instrument men, chief bonus clerk, draftsman, and a helper pool of four permanent men plus one or two students in the summer. The men are grouped according to function for organization purposes. Routine services provided by the Mine Engineering Department in-elude ail surface and underground surveying and mapping, preparation of working drawings, compilation of engineering reports, recommendations on ventilation, testing the mine air for carbon monoxide, research on mine equipment and its use, and the calculation of incentive bonus. Demand jobs from departments other than the Mine Department .are done on request. Such jobs may be in the plantsite, the Town of Murdochville, or at the shipping points at Gaspe harbour or the St. Lawrence river."

Jan 1, 1959

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By Christoph Müller

Information exchange for mine process optimization is essential. Today, modern mining equipment uses the IREDES standard to exchange production plans and reports for easy management and storage. To gain further benefits from process optimization, a mine wide access to real-time information is needed as e.g.: The current status of a machine, operational details etc. Presently, real-time data exchange systems are developed by machine producers. Each machine producer uses its own way of gathering, managing, and storing production data. These proprietary mining processes increase the complexity of cross platform data exchange and management for mines which involves machines produced by different vendors. Casting and unifying the data requires much effort. For this purpose, ?IREDES On-line? currently is being introduced. The standard defines an open, web based method for the exchange of volatile real time machine information. Two different principles are used: Web Services for cross platform information exchange within the IT world and the optional OPC UA for use with automation and process control systems. With such a standard information from machines of different vendors may be managed by using one common platform without spending the effort for dedicated interface development. Additionally, information management and storage will become straight forward since all the data are of the same format. The IREDES On-line standard utilizes the latest IT technologies as well as the knowledge and experiences gained from the previous IREDES standard. The paper explains the benefits, the use, as well as the technical design of the standard and gives application examples from the practice.

Oct 1, 2009

By R. Baker

A novel electrochemical half-cell and corresponding working electrode were designed to evaluate the electro-catalytic activities of catalysts in an environment close to that of an operating proton exchange or polymer electrolyte fuel cell (PEMFC). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were employed using the novel cell to characterize various methanol electro-oxidation parameters that contribute to the overall reaction on a fuel cell anode. The effect of temperature on methanol oxidation kinetics was examined in the potential range of 0.31 to 0.65V (vs. NHE). The data was collected in the temperature range of 20 to 80°C. Based on the experimental analysis and literature data, an equivalent circuit model (ECM) for methanol oxidation was proposed and was used to fit the EIS experimental data. The experimental data and ECM electrochemical data was used to extract electrochemical kinetic parameters for methanol oxidation such as the exchange current density, Tafel slope, and energy of activation for the reaction. Kinetic data, especially at different temperatures, is very limited in the literature.

Jan 1, 2005

By P. Massi

"Wholly owned by the Coniagas Mining Company, the oldest continuously listed mining company on the Toronto Stock Exchange, St. Andrew Goldfields is located on Hwy. 101 approximately 30 miles east of downtown Timmins, Ontario. Geographically situated on the Porcupine-Destor Fault, the mine and mill in Stock township is positioned in the heart of Northeastern Ontario's goldmining communities.In July 1988, a 600 ft. shaft, hoist, and compressors were already in place when construction started on a 500 T.P.D. capacity C.I.P. mill and crushing plant.By June 15, 1989 the mill was commissioned and attained the design capacity by August of that same year. Since then, changes to the circuit have increased throughput to 900 T.P.D. from two significantly different ore sources.Meeting the Ministry of the Environment's guidelines is an ongoing commitment utilizing the Inca S02 process in line between the tailings pond and secondary polishing pond.INTRODUCTIONExploration on what is now known as St Andrew Goldfields' Stock Township Mine was carried out ln the early l960 1 s by Hollinger Mines Ltd. The property was acquired by Quebec Sturgeon River Mines 1n 1973 and the main shaft was started ill 1979.When St Andrew Goldfields was incorporated 1n 1983, exploration and development commenced to identify the ore body. The company decided 1n 1987 to bring the Stock township property into production after an extensive feasibility study and testwork at Lakefield Research in Toronto. Leslie Engineering was contracted to design, engineer and procure al 1. equipment from the coarse ore bin to the tailings distribution system and backfill plant"

Jan 1, 1992

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By G. Q. Zhou, H. C. Liang, X. D. Zhao

"This study describes the strain behavior in vertical shaft lining (VSL) embedded in thick soil deposits and its application in assessment of concrete deterioration. The observed strain in VSL continuously decreased companied by a sinusoidal fluctuation due to the influences derived from negative skin friction (NSF) and temperature. The increase in strain increment between peak and trough at each year and compressive strain level as the servicing time continued and VSL depth increased implies that the concrete strength was attenuated, and this attenuation was significantly dependent on the existing compressive strain level in VSL. The reliability of the proposed approach was validated by Schmidt Hammer Technique (SHT) – based concrete strength, and is applicable in concrete assessment and then fracturing prediction of VLSs in thick soil deposits.Concrete strength, Field monitoring, Strain behavior, Vertical shaft liningINTRODUCTIONOver 100 VSLs in Southeastern China subjected to an unpredictable fracturing as shown in Figure1, and there are over 1,000 VSLs embedded in thick alluvium su?ering from challenges of damaging and potential fracturing (Cheng, Yang, Zhou, Li, & Hu, 1993; Zhou, Cui, Lv, Huang, & Chen, 1999; Li & Li,2005). Therefore, a reliable assessment of these VSLs is significant to the normal servicing of mine shafts and the recycle of underground space when these mine shafts were closed.The continuous increasing of NSF induced by the drainage of water–saturated deposits well interpreted such extensive fracturing phenomenon, and it is universally regarded as the governing indicator to determine the VSL stabilization (Cheng et al., 1993; Zhou et al., 1999). Based on this recognition, the fracturing prediction and VSL strengthening according to the field monitoring on hydrogeological characteristics, servicing environments, and mechanical behaviors of VSL were carried out (Zhao, Zhou, Zhong, Zhu, & Liang, 2009; Liang et al., 2009; Xie, Lv, & Wu, 2014). As known, the compressive strain level in VSL and the in–situ strength of VSL concrete were the main factors to perform such fracturing prediction. However, the existing studies in literatures were limited to the strain accumulating or releasing behaviors (Zhao, Zhou, Zhao, Kuang, & Hu, 2017), and lack of considering the VSL concrete strength and its attenuation. In this reported study, the in–situ monitoring data on the strain in typical VSLs and the VSL elevations between 2004 and 2014 were initially analyzed. Then, an observed strain behaviors–based approach was developed to quantitatively evaluate the VSL concrete deterioration."

Jan 1, 2019

By Robin Belley

Outline Introduction Wabush Mines HistoricalBackground Mine and Concentrator at WabushMines High Intensity Magnetic Separators (HIMS) Development of the Manganese Removal Process Pilot Plant Testing Phase Manganese Removal Line 1 Coming Phase: Manganese Removal Line 2 Manganese Concentration Process Development Historical Background 1847: Creation of the Cleveland Iron Company1850: Opening of its first iron ore mine in the Upper Peninsula of Michigan 1965: Beginning of Wabush Mines at Scully Mines, Wabush, Labrador. 1980-1990: Questions raised about how to exploit Scully high Mn Ore (> 2%)Part of the available ore is not saleable due to too high a level of pyrolusite (MnO2) Adding this ore to the resources would be valuable (longer mine life and lower stripping ratio) 1990s: Testwork for Manganese removal Many different processes are studied over more than a decade High Intensity Magnetic Separators (HIMS) are identified as the best technology for Mn removal 2007: Pilot Mn removal line installed Testing carried out through 2007-2008 First Production Line is ordered (2008) 2009: Cleveland Cliffs (now Cliffs Natural Resources)acquire the remaining part of Wabush Mines 2010: Mn Removal Line 1 construction & commissioning Summer 2011: Mn Line 2 Construction

May 1, 2011