Search Documents

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By R. D. Lawrence

"Comparable transaction analysis is the best known of the market approaches to valuation of exploration-stage mineral properties. The analysis of option and farm-in agreements can also provide useful guidance to valuators. While such approaches can be distorted by incomplete analysis, market-based methods are capable of providing consistent, credible results when carried out carefully with due consideration paid to all factors which buyers and sellers consider when dealing in the real market. IntroductionMineral properties without defined resources present one of the most challenging tasks to the mineral valuator. This paper will concentrate on market-based approaches to valuation of such properties. Other authors at MM2000 presented papers on cost and income approaches. Sorentino (2000) also provides a useful overview with some provacative commentary on methods.Market based-approaches are based on the principle of substitution and include such techniques as: comparable transaction analysis (sometimes referred to as sales comparison analysis); farm-in commitment (or option agreement) analysis; rules-of-thumb; and comparable market value analysis.Are there any valuation standards available to assist the valuator? In Canada there are none that apply to the valuation of mineral assets or securities. This problem is being addressed, at least in part, by the CIMVal Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM)1. Further, the recently established Canadian Association of Mineral Valuators will be giving consideration to the adoption of valuation standards."

Jan 1, 2002

By Norman A. M Macleod

FOR the past seven years, all flotation at the Britannia mill has been done in Forrester Air-Lift cells. Prior to 1931, the roughing and part of the cleaning operation had been performed in four 21-cell and two 14-cell M.S. machines. The resulting economies in reagent, power, maintenance, and general operating costs, and the increased recovery, more than justified the exclusive use of the Forrester machine. About three years ago, the possibility of still further improving the efficiency of the flotation section was the subject of considerable discussion and experiment. Arising from these experiments, tests were made of the practicability of using a cell of greater depth than that of any pneumatic or mechanically-agitated machine in common use. Cells were constructed with depths of 7 .5 feet, 10 feet, and 15 feet, and, in all cases, a very definite improvement in operation was indicated. The cell now being used in the mill treats from 5,500 to 6,200 tons of dry feed per day. It is 100 ft. long by 5 ft. wide by 8 ft. deep, and has replaced a total length of over 500 feet of standard Forrester machine. The choice of a depth of 8 feet was governed by the type of blower which was available-in this case, a Roots-Connersville blower, driven by a synchronous motor and delivering 6,000 c.f.m. of free air at 4.0 pounds per square inch. At the Chelan Division of the Howe Sound Company, where a new mill was recently built, all flotation is carried on in cells 10 feet deep, with good results.

Jan 1, 1938

By John D. Galloway

Mining is one of the important primary industries of Canada, with a gross production in 1927 estimated at $241,773,000- the highest in the history of the country-and an impressive dividend record. It is quite apparent, therefore, that mining is a business worthy of the careful attention of the people of Canada. Furthermore, with a vast undeveloped territory more or less mineralized, it is highly probable that our mining industry will continue to expand indefinitely, with a consequent increase in production and in the amounts of the yearly profits distributed. In recent years, the public has taken a larger interest than formerly in mining-an interest, moreover, that is not academic, but primarily from the viewpoint of profits. It is quite evident that mining is a profitable business, at least to some, and the average man on the street, hearing of these profits, is attracted thereto. I have no doubt that many of you have .read in promotion prospectuses, with figures to prove it, that mining is the most conservative, the safest, and the highest-yielding business in the world. Now, a lot of this information is best judged by the old saying that "While figures don't lie, liars figure". At the same time, mining, properly conducted, is a profitable business, even though speculative, and undoubtedly much profit will come from Canadian mines in the future. In this paper my conclusions regarding mining investments are based largely on British Columbia experience, together with some slight knowledge of mining conditions in the other Provinces. It is considered, however, that the inferences drawn are applicable to mining throughout Canada.

Jan 1, 1928

By J. Paturaud, A. G. Villemiane, J. Y. Buffiere, D. Fabregue, M. Perrier

In this work, a detailed characterization of the cyclic damage mechanisms on duty in car heat exchangers has been carried out in order to improve their reliability. The material which consists in very thin (<0.3 mm thick) sheets formed of 3 co-rolled aluminum alloys (4045 /3916/ 4045) has been brazed in order to obtain metallurgical and surface conditions representative of those of the real components. Fatigue tests at constant stress amplitude have been performed at room temperature and 120°C in order i) to characterize the cyclic resistance of the studied materials and ii) to study the effect of temperature on the fatigue damage mechanism. The mechanisms leading to failure have been identified from post mortem fractographic analysis. The Wohler curves obtained show that, contrary to common structural Al alloys, this type of thin sheet brazed multi material can be cycled for several hundred thousand cycles at very high stress level (> ~ 80 % of the tensile strength). This behaviour is analysed with respect to the microstructure resulting from the brazing process and the low number of grains present in the sample thickness (around 5 grains).

Jan 1, 2015

By C. E. Smith, R. J. Inglis, M. I. Brittan, J. H. Schoeman

"AbstractA number of plant-scale cyanidation tests were carried out in an attempt to uncover the causes of fluctuations in gold recovery efficiency. Computer analysis of the results verified that the treatment of reclaimed waste rock material along with normal run-of-mine ore was having an adverse effect on metallurgical efficiency. Mineralogical examinations showed that the free gold particles in the dump material were heavily tarnished or coated (predominantly by hydrated iron oxide), accounting for the lower recoveries. The indications were that the effect could be counteracted somewhat by using higher than normal cyanide and lime reagent concentrations and adequate leaching times. Analysis of the results showed further that leach pulp density was an important operating parameter affecting extraction efficiency. A variable activation energy leaching model provided an extremely good characterization of individual batch leach runs.IntroductionFLUCTUATING METALLURGICAL EFFICIENCY at the gold concentrator of the S.A. Land and Exploration Company Limited (""Sallies"") prompted some plant-scale cyanide leach studies in an endeavour to uncover the causes of the variations in gold recovery."

Jan 1, 1977

By Jean Robitaille

La découverte du gisement du puits Penna a nécessité une révision complète de tous les circuits du concentrateur Laronde pour permettre, premièrement, l?adaptation du procédé à la nouvelle minéralogie et deuxièmement, l&apos;accroissement du tonnage de 1800* à 4500 t/j. Aux circuits existants de broyage, de flottation du cuivre, de cyanuration et du charbon en pulpe, les circuits suivants furent greffés : broyage semi-autogène, flottation du zinc, manutention des concentrés (épaississage, filtration, entreposage et chargement automatisé), décantation à contrecourant et précipitation au zinc, destruction des cyanures et remblai en pâte. Cet article se veut une revue des différentes étapes du projet d&apos;agrandissement du concentrateur qui se sont effectuées par phases progressives de 1997 à 2000. De plus, une description des nouvelles technologies sélectionnées et implantées est présentée.

May 1, 2001

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By G. A. Vissac

In this paper we intend to deal particularly with the economic side of coal washing as it applies to our mines. We will then discuss why the dry-cleaning process has been selected, and give a brief description of our plant, dwelling only on its specific features and referring the reader to the numerous papers published on the subject for any details on the principles and machinery used in dry cleaning. ECONOMIC DISCUSSION The washery introduces an extra cost for depreciation, operation, and loss in treatment. A certain proportion of the coal, now being sold, and which the miners have been paid for. will have to be wasted. As a whole, the total increase in cost would be approximately 60 cents per ton. On the possibility of recovering this amount depends the success of the washery. There are two advantages to be expected from the washery, the first, which occurs at the mine and which will be certain; the second, more difficult to estimate, because it depends upon convincing our customers that they should pay more for a better product.

Jan 1, 1924

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By F. J. Hrach, K. P. Flynn, P. J. Miranda

"ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. Separation results are presented for selected industrial mineral sources. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.INTRODUCTIONThe lack of access to fresh water is becoming a major factor affecting the feasibility of mining projects around the world. According to Hubert Fleming, former global director for Hatch Water, “Of all the mining projects in the world that have either been stopped or slowed down over the past year, it has been, in almost 100% of the cases, a result of water, either directly or indirectly” (Blin et al., 2013). Dry mineral processing methods offer a solution to this looming problem."

Jan 1, 2016

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By E. I. Robinsky

"In light of the recurring spills and failures of conventional tailings disposal pond dams, a brief review of the Thickened Tailings Disposal (TTD) system is presented. It is shown that by the process of thickening the tailings to a heavy slurry prior to disposal, it is possible to create a self-supporting deposit of tailings and to eliminate the typical superimposed settling pond. These features, together with the ability to reclaim the disposal area even as mining continues, preclude an ecological disaster. IntroductionMine tailings spills are really not such rare occurrences. They have been happening on many continents, in many countries. Neither Canada nor the United States have been spared. In Ontario, the most recent spill occurred at a closed-down tailings disposal area in Matachewan, in 1991.Such continuing disasters could be avoided if a different approach were taken to the disposal of tailings wastes. The recent failures at the Los Frailes mine in Spain, the Omai mine in Guyana, and the Marcopper mine in the Philippines, will hopefully shake up the industry to consider other methods of disposal. The reason why the failure of a conventional tailings disposal dam is so environmentally disastrous is not the dam itself, but the fact that the dam retains a mass of very loose unconsolidated tailings and a great deal of water, or process fluid1. If the dam fails, the contents liquefy completely as they flow through the breach. In this liquid state, they can flow many miles downstream. If the dam itself were built of tailings material, as is often the case, it too would liquefy and join the flow.The reason the material is so loose in the first place is that it has been discharged into a pond filled with water. The tailings particles drift down through the water, their weight reduced by 50% due to buoyancy, to form a loose structure, like a “house of cards,” or lakebottom mud. It doesn’t take much of a shock to collapse the material into a liquefied state."

Jan 1, 1999

By A. Zangooi, J. A. Finch

"A frother analysis technique based on the formation of a colored solution with UV-VIS absorbance proportional to frother concentration over a certain range has been developed. The calculation of concentration requires the comparison of the sample absorbance at a selected wavelength with a linear calibration (frother concentration vs. absorbance) constructed with values collected from solutions of known concentration (standards) at the same wavelength. It has been found that concentration ranges for preparation of standards can vary widely. An integration of our experiences into a databank can offer some guidance on the selection of standard concentrations. The databank includes results from the analysis of 37 chemical reagents, commercial frothers, and natural oils used in research work or at industrial sites. Grouping frothers by similar chemical structure or origin provides a good basis for selecting the standards to approach the maximum absorbance range for the spectrophotometer in use.INTRODUCTIONA technique to determine frother concentration on samples of industrial milling streams based on formation of a colored solution with UV-VIS absorbance proportional to frother concentration has been developed. The concentration is determined by comparison of its absorbance, at some selected wavelength, with those obtained by processing a series of solutions of known concentration (standards), at the same wavelength. It is desirable to have linear calibration (frother concentration vs. absorbance) over the widest concentration range. The upper concentration can be restricted by the instrument, as there is a maximum detectable absorbance (minimum transmittance), which can be reliably sensed by the UV-VIS detector (in most cases maximum absorbance is 3)."

Jan 1, 2016

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961

In several European countries, including Russia, it has become economically attractive to utilize peat as a fuel for power generation, the production of metallurgical coke, the production of fuel briquettes for the domestic market and low-Btu gas. Although the economic base and availability of energy supplies in Europe is much different than it is in Canada, regional economics here may warrant the development of peat as an alternative source of energy. Canadian peatlands cover several thousands of square miles and have historically been considered as waste land. Now, with the increasing costs of other energy sources, it is apparent that fuel peat should be re-evaluated as a potential energy resource. A nation-wide inventory of peat deposits has been prepared and reserves evaluated for some of these areas where field surveys have been carried out. The paper describes alternative mining methods developed to meet some of the various conditions encountered on virgin peatland . These mining techniques are generally based on current peat technology exercised in other parts of the world and would be applicable in some of the peat regions of Canada. Cost estimates have been prepared for peat production in regions of Canada, and the socio-economic aspects of a large-scale fuel peat operation are discussed. Several potential utilization schemes have been described, with particular emphasis on electric power generation. The paper makes recommendations for steps to be taken in the development of a fuel peat industry in Canada.

Jan 1, 1978

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

"A simple approach to optimizing the performance of an operating carbon in pulp (CIP) or carbon in leach (CIL) plant is presented. It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch tests in which the rates of gold leaching and carbon adsorption are determined, coupled with mathematical models that translate the batch kinetic data into predicted steady state profiles of gold in solution and on the carbon across multi-stage adsorption circuits.Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the stepwise change can be determined. In this way it is possible to inexpensively optimize the design of both greenfields CIP or CIL circuits and plant expansions, or optimize the operating parameters of an existing plant, with no disruption to plant operations and no economic risk to the mining company.This approach has been adopted by IAMGOLD Corporation, to the immediate benefit of two of their existing gold operations. The methodology adopted and the results achieved are presented.INTRODUCTIONThe carbon in pulp (CIP) and carbon in leach (CIL) processes became firmly established in the gold mining industry in the 1980s, initially in South Africa and Australia, from where they spread rapidly to all the gold producing regions of the world. The percentage of annual global gold production by activated carbon-based processes grew from zero in the 1970s to almost 70% by the turn of the century, which represented a phenomenal rate of acceptance of a new technology by a traditionally conservative industry. The main reason for this rapid acceptance of the new technology was the fact that the first few large plants built in South Africa convincingly demonstrated better gold recoveries than the traditional filtration/Merrill Crowe process, with lower capital and operating costs. And as the plants developed an operating track record over their first few years of life, they proved to be remarkably robust mechanically, and highly tolerant of plant upsets, changes in feed composition and solution phase contaminants that had caused problems in Merrill Crowe plants."

Jan 1, 2011