Search Documents

By Edward Sampson

Bases of National Power At a time when the economy of the world is in a particularly troubled state it is appropriate to examine some problems of the distribution of natural resources. I should like particularly to call attention to the remarkable increasing demand for natural resources, to give an analysis of the demand for certain mineral resources, and to direct attention to some problems in satisfying this demand. All industrial power is based on natural resources and the most basic of these are soils, energy resources, and mineral resources. There is a strong interrelation of these resources, more than is obvious, and I shall take up certain aspects from the point of view of a geologist. Few nations are well endowed with all three of the kinds of natural resources I have mentioned and much has been done by some small countries whose peoples are industrious and enterprising and where conditions for free world trade have been favourable. However, major industrial power is dependent on a substantial endowment of all three classes.

Jan 1, 1949

By P. Patnaik, F. Cuneo, D. M. Wang

Microwave (MW) energy has been used widely for several decades for communications, food processing, wood drying, vulcanization of rubber and medical therapy. Recently, this technology was found to be capable of successfully sintering ceramic and metallic powder materials, with the advantages of reducing soaking times and sintering temperatures. Unlike conventional heating, MW radiation works through the absorption of the microwave energy by a material placed in an electromagnetic field within the microwave cavity. A far more efficient heating process is produced due to the unique ability of microwaves in selectively heating a pecific part of the material with desirable dielectrical properties. This exploratory research was initiated with the objective of locally sintering the thermal barrier coating of gas turbine components using MW radiation. This novel technique may allow repairing of the component without subjecting the entire piece to unnecessary elevated temperatures and reduction of process time and cost. Y ttria stabilized zirconia was used in this study and sintering was conducted using a multimodal 1.2 kW microwave facility. Three configurations of heating setup were experimented and the preliminary results will be discussed in this paper.

Jan 1, 2006

By R. M. Young

In. East Kootenay, two Companies are operating, the Crow's Nest Pass Coal Company of Fernie, with mines at Coal Creek and Michel, and the Corbin Coal and Coke Company, of Corbin and Spokane. Wash., with mines at Corbin. The Crow's Nest Pass Coal Company has also coke-ovens of the bee-hive type at Fernie and Michel. The mines have a productive capacity, with present development and plant, of approximately 1,500,000 tons of coal, and of 300,000 tons of coke annually. The total production in 1923 was 828, 990 tons of coal and 65.990 tons of coke. In the early years of operation, the mines furnished a very large percentage of their output to the railways and smelters. These were, in fact, the primary markets for which the mines were opened and the ovens constructed. The Great Northern Railway had built into Femie, and later extending its line to Michel, became a heavy consumer of both of these mines. The Spokane International, connecting the Crow's Nest branch of the C.P .R. with Spokane, furnished tonnage to Corbin. The Canadian Pacific Railway bought for Crow's Nest consumption. The smelters at Grand Forks and Trail in the Boundary country were large and steady consumers of coke, while in-termittently Northport, Butte, Helena, and Great Falls shared in the product of the ovens.

Jan 1, 1924

By E. Gaucher, M. St-Amant

"Among the electromagnetic surveys performed by SOQUEM in the last three years, a certain number of the more instructive cases have been chosen to illustrate the theory of electromagnetism by field examples of: (a) The depth penetration of the TURAM as compared to the SLINGRAM (Ronka) method. (b) The limitations of the TURAM as compared to the SLINGRAM method when a conductor dips the wrong way, or when it is small in size. (c) The expression of a shallow-dipping conductor in a SLINGRAM survey. (d) The effect on the SLINGRAM survey of deep ditches or reef structures.(e) A comparison between the CRONE and the SLING-RAM method in the Abitibi clay belt, by means of field and model studies, indicating a usually better signal-to-noise ratio for the SLINGRAM method. From the above and from other experiments, different electromagnetic methods are now being used by SOQUEM, depending on field conditions."

Jan 1, 1970

By Gaston Gingras

"IntroductionL'entretien de l'equipement minier dans les mines à ciel ouvert est une activité qui est aussi vieille que I'existence des mines et qui a progressé au cours des années pour suivre l'évolution des techniques d'exploitation. Lors de la mise en usage de s premières pelles à la va peur, celles-ci étaient généralement entretenues par I ‘équipe de quatre hommes qui était responsable de son opération. Pour les travaux plus compliqués ils utilisaient les services de machinistes qui eux savaient comment réparer Ie moteur à vapeur et couler des coussinets de ""babbit"". Les premières pelles diesel étaient entretenues de la même façon mais pour les réparations au moteur, on devait recourir au représentant du manufacturier qui était Ie seul à avoir les compétences nécessaires.Ce n'est vraiment qu ‘après la deuxième guerre mondiale que I ‘usage de l'équipement mobile s'est répandu dans les mines à ciel ouvert pour débuter les extractions selon les méthodes que I'on connaît aujourd'hui.L'entretien de l'équipement minier de façon organisée à débute avec I ‘usage de ces machines dans nos mines. Ces machines étaient un peu primitives, petites et pas très dispendieuses a I'achat. Même si la disponibilité était basse, elles fournissaient quand même un rendement qui en ces temps était acceptable. L’organisation de I ‘entretien de cet équipèrent était assez primitif et n'occupait qu'une place secondaire aux yeux de la direction de la mine."

Jan 1, 1988

By M. Sukhram

In the year 1992, T.A. Utigard published a paper titled "The measurement of the heat-transfer coefficient between high temperature liquids and solid surfaces." In that work, he instrumented an agglomerate of materials with thermocouples to infer the heat transfer coefficient of a high temperature liquid on a solid. The purpose of that research was to help in the design and operation of metallurgical reactors. Since that time there have been many researchers that have worked to characterize heat, mass, and momentum transfer phenomena in high temperature metallurgical processing operations. This paper presents results from the author’s experience with instrumenting thermocouples in copper elements coated with carbon to infer velocity of high temperature liquid metals. It also presents a methodology to determine velocity of a high temperature liquid by inferring the local heat transfer coefficient at a solid-liquid interface

Jan 1, 2015

By G. B. Harris, C. W. White

A study to investigate the recovery of base metals, notably copper, nickel, cobalt, zinc and manganese from iron-free concentrated chloride solutions using ion exchange was undertaken. In such solutions, apart from nickel and, to a lesser extent manganese, these metals are present predominantly as complex anions, and therefore conventional separation techniques based on cationic resins are not applicable. The results demonstrated that zinc, copper and cobalt can all be separately recovered leaving nickel and manganese behind. Specifically, zinc is a major nuisance element in nickel and cobalt processing, and the testwork showed that it can be preferentially removed prior to copper and cobalt. Selective resins for both copper and cobalt were identified, and it was demonstrated that the strength of the chloride background matrix has a significant effect on the efficiency of separation. An additional major advantage in such systems is that stripping can mostly be effected with water. Finally, some observations are made on the hurdles that must be overcome when attempting to introduce and commercialise new technologies.

Jan 1, 2015

By Thomas G. Madgwick

Introduction Development of oil and gas is still centred in the Province of Alberta, much as it was when C. C. Ross read a paper on this subject three years ago at the Annual General Meeting in Montreal; but so far as gas is concerned, its early production in Saskatchewan seems now assured. The three years that have elapsed since Mr. Ross' paper have witnessed a growth in the world's production of oil that has created a potential supply out of all proportion to the demand for petroleum products, and one that has resisted the most energetic efforts of the industry entirely to control. The natural result has been very much to retard the active prospecting of new structures in the Prairie Provinces with any immediate view to oil production, although the same factor has not hindered the search for gas to the same extent. One consequence has been to divert the attention of organized oil operators from wildcat drilling to more detailed geological investigation than had hitherto been customary, sometimes accompanied by test drilling with a view to the elucidation of geological structure rather than to the immediate development of production which at the present is not needed. Nevertheless, in spite of the growth of this phase of oil prospecting - which the writer would be the last not to welcome as a very real blessing and of far greater value than indiscriminate wildcat drilling in either the complex structures of the foothills or the simpler but largely concealed formations of the plains- it is most satisfactory to have to record that in these three years the growth of production both of naphtha and the heavier crude-oil has kept pace with the by no means inconsiderable growth in the production and utilization of natural gas.

Jan 1, 1929

By Christie Myburgh, James Mackenzie, Ross Hammond

Modern mining operations are increasingly characterised by their access to large volumes of data and advanced computational tools. Over the past two decades, the industry has made substantial investments in digital technologies supporting geological modelling, mine planning, equipment dispatch, and process control(Newmon et al., 2010; Paraszczak, 2019). These systems have significantly improved the ability to generate and analyse information across the mining value chain. However, despite these advances, the decisions that ultimately determine operational performance remain largely implicit and unmanaged (Kruger et al., 2023; Jia, 2022). Mining decisions rarely occur in isolation. Decisions made in geology influence resource models, which shape mine plans, production schedules, and downstream processing strategies. These, in turn, affect operational execution. As deposits become deeper, ore grades decline, and operational constraints increase, these interdependencies create increasingly complex decision environments (Newman et al, 2010; Topal, 2008; Darling, 2011; Dimitrakopoulos, 2004). In practice, coordination across these domains often relies on informal communication, iterative meetings, and manual interpretation of analytical outputs. Explicit decision support systems provide a mechanism to capture these dependencies, maintain consistent decision context, and coordinate decision-making across geological, planning, and operational domains (Power, 2002; Shim et al., 2002). This paper argues that a fundamental gap remains in current digital mining systems: while data and analytics are well supported, decision-making itself is not. Addressing this gap requires treating decisions as explicit, structured elements within the operational system. By integrating data, computational analysis, and decision processes, explicit decision support systems offer a way to better coordinate complex, interdependent decisions across mining operations.

May 2, 2026

By James Anstey

BHP Billiton?s Cannington facility is a mining and minerals processing plant near Mt. Isa in Central Queensland, Australia, producing silver, lead and zinc. Mine ore is processed in a concentrator, which consists of grinding, flotation, thickening and filtration. Grinding is carried out in a fully autogenous (AG) mill. The mill operates in closed circuit with a pebble crusher. Throughput is approximately 380 tph. Cyclone overflow from the grinding circuit is fed into a flotation circuit for the recovery of lead, zinc and silver. Two concentrates are produced (lead and zinc), which are then thickened and filtered. The filtered concentrate is transported by road to a rail receiving station. From here the concentrate is railed to port in Townsville for shipment to the smelter. Matrikon and Engineers at BHP Billiton?s Cannington Mine have used ProcessACT to develop a flexible, nonlinear dynamic simulator for the grinding circuit to further enhance process understanding, as well to investigate various optimization strategies. An online charge volume estimator was also developed for the AG mill to aid in the understanding of overload conditions, which for the previous two months had been the primary contributor to downtime. The models were developed using a combination of first-principles modeling along with input-output dynamic responses. Examples of models used include: Morrell ?C? model for power and charge shoulder/toe angle prediction; Whiten?s mixing model for breakage and hold-up; Nageswararao cyclone model for predicting cut size; slurry recovery and water recovery. The composite model simulates system dynamics starting from the stockpile reclaim system and finishing at the feed for the flotation process. The objective was to provide a tool that assisted Cannington in understanding their Grinding Circuit and allowed them to develop and evaluate circuit optimization strategies. BHP Billiton Cannington Mine is now considering development of a Grinding Circuit Optimizer utilizing the models developed for the simulator.

Apr 1, 2005

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

By M. Ramström

"In 2002, Atlas Copco Rock Drills AB released the new rig control system (RCS) technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging, reduction in manpower in some types, and serviceability have all taken a quantum leap forward when compared with previous generations of drill rigs. RCS is modularized and distributed by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions."

Jan 1, 2005

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By R. P. Townsend

It is a widely accepted "fact" that a Koepe friction hoist is generally the best solution for production hoisting when compared to a double drum hoists. This would appear to be true if one looks at the initial capital cost of just the hoist, and also if one compares the size of the motors selected for the duty. But is this the whole story? What are the longer term costs involved in the hoist's operation, and what are the relative efficiency's of the two designs? Perhaps the Koepe hoist design enjoys a better reputation than it deserves.

Jan 1, 2011

By R. Stratton-Crawley, S. W. Wilson

"Inco's Matte Separation Plant is a unique mineral processing facility having no process tailings stream. Each product is a high-grade concentrate with strict assay specifications which are defined by the downstream refining route. The most recent column application in the flowsheet, copper scavenging in the production of a high quality nickel concentrate, is described in detail. Testwork in pilot-scale columns (0.038 m, 0.051 m and 0.10 m in diameter) was used to develop a model of the copper scavenging system. This data was then used to simulate the performance of plant-scale equipment. The relationships thus established were confirmed by a series of plant tests in a 1.8 m diameter column. Column results consistently exceeded conventional cell performance. The modelling was extended to assess full plant production requirements and, as a result, a 2.1 m diameter column was specified for this application. Engineering design for this column is currently underway and the column is scheduled to be commissioned later in 1991.INTRODUCTIONMatte SeparationINCO's Matte Separation Plant is a part of the Copper Cliff Smelter complex near Sudbury Ontario. The flowsheet and the development of column flotation within it have been described previously (Feeley et al., 1987, Wilson et al., 1989). The plant feed is a synthetic Bessemer Matte from the Nickel smelter. This matte is slow cooled to promote grain growth and typically assays 46-52% Ni, 23-27% Cu. These elements are present primarily in sulphide form (Ni3S2 and Cu2S respectively) with some metallic alloy also precipitating from the sulphur deficient matte. Minor amounts of iron, precious metals, and nuisance elements are also present.The matte separation process is, in concept, relatively simple. Following magnetic removal of the metallic alloy from the feed, the flowsheet is designed to float a high grade copper concentrate from the nickel sulphide matrix. A simplified flowsheet of the process is shown in figure 1."

Jan 1, 1991

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country's primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country's many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was 'subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949

By E. Nurminen

Thermal transport properties of copper flash smelting flue dust have been investigated. Such values of the dust are needed to correctly model the process and to optimize its heat recovery performance. Dust accretions on heat recovery boiler walls may have a significant influence on the boilers heat transfer efficiency. Measurements of the thermal transport properties have been made for industrial flue dust and for pure sulphate components. The measurements have been conducted at temperatures up to 400 °C and the effect of porosity on these properties has also been investigated. The results indicate that the flue dust and the sulphate components are effective thermal insulators and the dust build-up on the boiler walls is likely to greatly decrease the heat transfer efficiency of the boiler.

Jan 1, 2007

By G. M. Brownell

THE Falcon Lake stock is a small igneous mass, 2.6 square miles in area, which has intruded a belt of older lavas and metamorphosed sediments. It is well exposed and the entire area of its outcrop is taken up with surveyed mining claims, the claim lines forming a grid which makes ideal conditions for a detailed petrographical study of the unusual variations which are found in the composition of this unit (see Figure 1). The study of this mass, which has revealed features of both scientific and economic significance, began in the summer of 1939 when trainees in a Prospectors' Training Camp, a Do-minion-Provincial youth-training project under the writer's supervision, were, detailed to map rock outcrops on various mining claims. Microscopic study of rock specimens taken on a line across this stock were made during the following winter and proved to be of such interest that a special trip was made the following summer for the purpose of gathering more data, the results of which are presented here. Location The stock is close to the southeast corner of the province of Manitoba, about three miles from the Ontario boundary. It lies between Falcon and West Hawk lakes and less than a mile south of the Trans-Canada highway. It is easily accessible by motor car, as a branch road from the highway leads to the Sunbeam Kirkland gold mine, which is within the inner core of the stock. Previous Work This area was the first in the Province to receive attention from prospectors, who entered it from the adjacent Lake of the Woods district during the days of the mining boom in the 1890's. Small occurrences of gold, copper, molybdenum, and tungsten ores were found, but to date there has been no production from the district, except for small shipments of gold ore. The regional geology has been mapped by the Manitoba Department of Mines and Natural Resources, the Falcon Lake stock being shown and recorded as of "varying composition". The more detailed work involved in preparing the accompanying map has necessitated only minor changes in the outline as previously mapped.

Jan 1, 1941