Search Documents

By G. Shen, W. R. Tyson

In most fracture toughness test standards, such as ASTM E 1290 and BS 7448, crack-tip opening displacement (CTOD) is measured by using three-point bend (SE(B)) or compact (C(T)) samples with deep cracks. The loading mode and crack depth in these tests sometimes are different from that of pipelines. Pipelines usually have shallow defects and experience tensile loading when the supporting ground moves. As a result, the CTOD measured by these samples is lower than that of pipeline in tension. Recent researches suggest using single-edge-notch tension (SE(T)) samples to measure fracture toughness for pipelines. In the present study, shallow and deep SE(T) samples under fixed grip loading were analyzed by using the finite element technique. An equation to relate the CTOD to the area of the load/plastic crack mouth opening displacement (CMOD) is proposed. With this equation, the CTOD of a SE(T) sample can be evaluated by measuring the area under the load/plastic CMOD curve of a SE(T) sample.

Jan 1, 2005

By J. Olaf Sund

"The New Brunswick gypsum and an-hydrite deposits make up part of the Windsor group in the Upper Mississippian. The present deposits were formed by surface hydration of the underlying anhydrite beds. The sub-hydrate, hydrate, and di-hydrate stages of gypsum are formed from the anhydrite by this hydration. The anhydrite was precipitated from sea water in embayments that were separated from the sea by a reef or bay-mouth bar. The anhydrite is the original form of the calcium sulphate precipitate.One gypsum deposit near Plaster Rock in northern New Brunswick was precipitated from sea water directly as gypsum, which is its present form."

Jan 1, 1960

"3.1. IntroductionAmong the six platinum-group elements (POE), four have identical cubic symmetry, two identical hexagonal symmetry (Table 3.1). Despite crystallographic differences, there is a clear relationship expressed in the chemistries of the POE: they tend to be mutually soluble in one another and can frequently substitute for one another in compounds with other elements. This chapter consolidates the data on phase relations of the POE and the compounds they form with elements selected for their known or potentially important mineralogical significance- As, Bi, Cu, Fe, Hg, In, Ni, Pb, S, Sb, Se, Sn and Te-together with selected data for the occurrence of POE in certain elements such as Au and Ag, and compounds such as FeS. Resources used to compile the data are those available from the chemical, mineralogical and metallurgical literature. First each element is discussed, with composition limits of solid solutions drawn from binary phase diagrams. Single element data are followed by a discussion of the relevant binary systems and a tabulation of data for binary compounds found in those systems (Table 3.2). Tables and diagrams for the ternary and quaternary systems for which information is available follow, and finally the very limited information on the solubility of POE in mineralogically important elements and compounds is presented.The chemical, mineralogical and metallurgical literature on the unary and binary systems is extensive and widely scattered in many languages and publications; fortunately, most of the data needed to compile this chapter can be found in reliable compendia. The most useful and most recent of these works is by Moffatt (1979), because it provides a ready index to all material relating to binary systems listed in previous compendia; furthermore, the Moffatt compendium will reportably be kept up to date by annual supplements."

Jan 1, 1979

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly

"A numerical model has been developed to study macrosegregation associated with liquid feeding in the Low Pressure Die Casting of A356 aluminum alloy wheels. The model of the wheel casting process has been implemented within the commercial CFD software package, FLUENT, using a User Defined Function (subroutine) to account for Si rejection based on the Scheil approximation. The model has been validated against temperature and microstructural data taken from a commercially cast wheel. The amount of segregation in the wheel has been shown to be significant in a couple of key areas. The implications of accounting for segregation include an improved ability to predict shrinkage porosity, fatigue performance and potentially also hydrogen porosity.INTRODUCTION The aluminum alloy A356 is widely used in the automotive and aerospace industries for various components. Examples include automotive wheels, automotive suspension components and airframe castings. Focusing on automotive wheels, Low-Pressure Die Cast (LPDC) A356 wheels offer significant design freedom and are far more aesthetically appealing to consumers than conventional stamped steel wheels. A356 wheels now dominate the market, appearing in all but the entry level offerings of the OEM manufacturers. However, they are typically over-designed to allow for the various casting related defects that degrade their mechanical performance. Thus, their potential to save weight has not been fully realized. Wheel manufacturers are under constant pressure to ensure their products meet strict mechanical requirements (ductility, fatigue, vibration), tight geometric tolerances and high aesthetic quality. The mechanical properties of the final product are determined by the microstructure – e.g. SDAS – and the defect population (porosity and oxides). Depending on their size and location, both porosity and oxides, can act as crack initiation sites reducing fatigue life (Caton, 2001; Jordan, 2010; Wu, 2015). There are a number of examples appearing in the literature (Atwood, 2000; Carlson, 2007; Lee, 2001; Yao, 2011) of numerical models that have focused on hydrogen-based pore formation that have demonstrated an ability to predict porosity formation and pore size distributions in geometrically simple castings. These models assume that the local gas species diffusion through the liquid metal to the pores is the rate-controlling factor of pore growth. Another common source of porosity is liquid encapsulation (Dantzig, 2009). As the pressure within the isolated liquid drops, pores form first due to the pressure dropping below the equilibrium partial pressure of hydrogen in solution and then second grow substantially as the pressure continues to drop falling below the vapour pressure of Al. One factor that can affect both mechanisms of pore formation is species macrosegregation, which has received comparatively little attention in die-casting."

Jan 1, 2017

By H. B. Lumsden

This paper is intended to deal merely with the commercial development of some of the principal non-metallic mineral resources in the three prairie provinces- Manitoba, Saskatchewan, and Alberta. Coal is not included in this summary. Building Stone First and foremost, mention may be made of the building stone now being produced at Tyndall, Manitoba. This is a mottled limestone and is declared by experts to be one of the finest building stones in America, both as regards durability and appearance. It has been used very extensively both for exterior and interior work, not only in western Canada, but also in the principal cities as far east as Montreal. The stone is the "'Upper Mottled Limestone", which forms the summit of the Trenton (Ordovician) strata in the Lake Winnipeg basin. Quarries are at present being operated at Garson and Tyndall . The area where this stone is known to be available extends in a north and south direction for a distance of three miles, and the main productive ridge is probably about one half mile wide. The outlook for the future of the industry is extremely promising, as the stone is becoming increasingly popular in Eastern Canada, more particularly for interior work.

Jan 1, 1928

By O. Kodym

The paper has focused on possibilities of interconnecting information sources concerning monitoring & control of mining industry technical processes (TP), and the related safety hazards. The key issue is the comprehensiveness of the information presented to users. Information can be presented by virtual reality means, when the seemingly true presentation of the production process scene along with user friendly presentation of related information is available. The user in its role of a process supervisor is not only a mere scene observer but, thanks to the interactive functions of virtual environment, he participates in the scene of his control. As such his control and management abilities increase because he can absorb, more easily understand and asses the information provided.

Aug 1, 2013

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014

By M. M. C. Lima, L. C. S. Solimani, M. A. Quintela

Galvanized steel scrap is recycled to B OF converters where zinc escapes from the bath and is captured by the gas control system, appearing in BOF sludge. As BOF sludge contain high iron content, it could be recycled, but due to its zinc content, it is disposed in landfills. In this study techniques were evaluated for zinc layer removal from scrap by sulfuric acid leaching. The effects of coating weight, temperature, time and sulfuric acid concentration were evaluated for three different galvanized scrap. The results showed that the behavior of each galvanized scrap was different. Nevertheless zinc removal efficiency was more than 80% with low dissolved iron in the leached solution.

Jan 1, 2011

By George W. Bain

Mr. Geo. W. Bain: Dr. H. C. Cooke's discussion of 'The Geology and Mineral Deposits of the Harricanaw and Bell River Basins' possesses many of the elements of a good political address; perhaps his long residence in Ottawa has some bearing upon his method of discussing geological work. The three essential parts of the address are all included. First, the plank - "Contributed discussion on the Geology and Mineral Deposits of the Harricanaw and Bell River Basins"; second, the personal attack upon the opponent, to show antipathy to the opponent as well as to his ideas; and third, controversion of a number of statements, which have been made to appear as planks of the opponents platform, even statements and work which are in no way connected with one under discussion. In the following pages, I will confine my attention to a defense of my work in the Harricanaw and Bell River basins, leaving discussion of the other areas mentioned by Dr. Cooke until results of the re-surveys are published. It is intimated that it was impossible to make a geological examination of an area of 1,600 sq. miles on a scale of four miles to the inch (base map supplied) in three and a half months, because "the area is accessible only from the railway along the northern edge together with a few roads close to it, and from rather wide separated streams?. There is one way, known to most geologists, whereby a place can be reached other than by railway coach or motor boat, and that the oldest of all -- walking. Most of the region was reached in this fashion. The boundaries of all the 18 townships included in the map are surveyed, nine are divided into lots, and the north-south and east-west centre lines of most of the others are surveyed and have mile-posts placed.

Jan 1, 1927

By C. R. Stelck

"AbstractThe Cardium formation of northeastern British •Columbia •contains an erosional unconformity that becomes progressively more severe northward until, •at Liard river, the stratigraphic hiatus eliminates the underlying Lower •Cardium sandstone, the Kaskapau formation, and the upper Dunvegan sandstones. The area of unconformity roughly coincides with the distribution of the continental facies of the earlier Dunvegan formation. Along Wapiti river, the zone fossil Scaphites ventricosus Meek and Hayden is found in the Bad-heart member of the overlying Wapiabi shale; Scaphites :preventricosus. Cobban marks the base of the Wapiabi shale; Scaphites cf. corvensis •Cobban is found in the middle shale member of the •Cardium formation. The log of the Red-Willow No. 1 well shows close similarity to the outcrop sections south of Wapiti river. The Cardium formation is mainly late Turonian in age. Two other pre-Cardium Turonian sands of north-eastern British Columbia are named the Wartenbe and Tuskoola sands.IntroductionTHE Upper Cretaceous Cardium (Bighorn) sandstone formation of the Foothills of northeastern British Columbia carries within its formational limits an erosional unconformity. The unconformity decreases to the southeast, becoming in immediate shoreline regions, now under the plains, a minor diastem. Such diastems, or stratigraphic intervals of non-deposition, occurring in the shallow unda-zone are paralleled in the deeper portions of the unda-zone by the phenomena of sub-aqueous winnowing. '.This winnowing and re-working •at critical depths creates sand areas with porosity."

Jan 1, 1955

By Jehan Rondot

Les trois intrusions alcalines de Suzorite en haute Mauricie, bien que non datees, son! sans doute d ,attacher aU)( nombreuses autres intrusions alcalines dispersees sur les blocks Grenvillia et Laurentia et datees de I 050 Ma =t= 10%, done reliees d l'orogene grenvilien. L 'utilisations de la Suzorite est liee d sa forte proportion de phlogopite (>50%). Le rapport Mg/Fey varie de 3 d 7. Sa mineralogie et sa composition particulieres (forte proportion de Mg, Ket H20) en font son attrait.

Jan 1, 1984

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By Brien A. Perry, Art Wiebert

"Many organizations which have implemented Total Quality Management (TQM) are finding that the process has either stalled or is not working so well as originally envisioned. This can be particularly evident in an engineering environment where the uniqueness of engineers and their particular culture has not been adequately considered. Winning the commitment of a highly educated group ojprojemnnJJ1s to the TQM concepts, which are often initially 5W2 as too simplistic poses special challenges.Successful TQM implementations are found among technical groups where employees have significant input into creating the new work culture, feel empowered to make changes and are well trained in teamwork. A coach who is knowledgeable in implementation problems can, when working closely with the technical teams, help them circumvent obstacles and guide them successfully through the difficult early phases. The remaining key ingredient for success is supportive management which leads the change and is both informed and appreciative of the accomplishment being made.This Paper is based on first-hand experience with common problems and results encountered in implementing TQM in an engineering environment. Described in the paper are ways of avoiding these problems through awareness of the unique nature of engineering groups, implementation planning, just-in-time training and coaching people in the TQM process. The paper concludes with a focus on the opportunities and results from a successful implementation. These opportunities and results include the benefits each engineer can realize through process thinking, empowerment and teamwork."

Jan 1, 1995

Presentation Topics ? Low and Intermediate Level Waste ? Project Location and Site ? Geological Setting ? Key Features ? Project Overview ? Licensing and EIS ? Next Steps DGR Waste Package Inventory Approximately 50,000 packages over 35 years: ? ~40,000 packages or 80% of inventory are LLW Bins ? ~7,000 ILW Shields (concrete boxes) ? ~2,000 resin liner packages

Oct 1, 2010

By Vladislava A. Ignatkina, Victor D. Samyguin

"Within the limits of two-phase approach, considering mass transfer with pulp and air streams was shown that each bubble appears to be an elementary carrier, transporting particles from the collection zone into the froth. The kinetics of flotation was described by the exponential equation in which first order flotation speed constant has to be replaced with two-phased coefficient of a mass transfer. Criteria of selectivity of two ore fractions separation, based on determination of optimum time at which maximum difference between extractions and components content in separated fractions were offered. An interrelation between optimum time of pulp residence in a flowing chamber of a flotation machine, time of bubbles mineralization and an optimum airflow has been ascertained. Cumulative criterion of mass transfer efficiency of flotation process has been ascertained to be a form of the spectrum and its position on axis of three-phase coefficient of a mass transfer.INTRODUCTIONRegularities of a mass transfer of three bearing streams: pulp stream, air stream and froth stream underlie theory of mineral complexes flotation (Samygin, Filippov, & Shekhirev, 2003)However, only description of mass transfer in pulp stream by means of kinetic equations that were simple and convenient for practical use, has gained a full distribution (Tykhonov, 2009;Rubinstein&Filippov, 1980; Saleh, 2010).Within the limits of a single-phase approach, the role of gas stream in increase of speed and selectivity of flotation, was associated with an improvement of hydrodynamic mode. An influence of particles and bubbles sizes (Rubinstein&Filippov, 1980; Rubinstein&Samygin, 1998, Samygin et al., 2003; Dai, Fornasiero,& Ralston, 2000), of pulpflow and airflow (Finch& Dobby, 1990) and turbulent energy intensity (Shubert, 1979; Massinaei, 2007) on the flotation process has been studied. It was stated that flotation selectivity is increasing by means of gradual airflow increase from first to final cameras of the impeller flotation machine (Aslan&Boz,2010; Finch, 2011) and by means of using a multizone flotation machine (Samyguin, Filippov, Matinin, Lekhatinov, &Tertyshnikov, 2013)."

Jan 1, 2016

By Tassos Grammatikopoulos, Sarah Prout, William Mercer, C. Gunning

"The Nechalacho rare metal deposit is located in NWT, Canada. Avalon Rare Metals Inc. is now evaluating processing techniques for recovery of REE to be used in the industry. QEMSCANTM analysis coupled with whole rock, REE, Zr and Nb, and electron microprobe analyses were utilized to identify and quantify the mineralogy of the deposit, and define the REE distribution among minerals. QEMSCANTM mineralogy was performed on fifty intact drill samples using EXPLOMINTM that provided textural information for the mineralization; crushed samples were used to determine the variability of the ore and define REE domains, and composite samples to determine the liberation and association of the REE minerals. The sample matrix predominantly consists of biotite, feldspars, quartz, muscovite/clays, minor chlorite and amphibole, magnetite and hematite and carbonates. REE include in decreasing order of abundance allanite (3.6%), monazite (1.5%), synchysite (0.9%), columbite (0.9%), fergusonite (0.6%), bastnaesite (0.4%), and zircon 11.0%. The majority of the HREE are carried by fergusonite and zircon, and the LREE by monazite, allanite, synchysite and bastnaesite. QEMSCANTM mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data have been implemented in defining the mineralogy of the ore body, support metallurgical test work, predict recoveries and grades, and finally calculate reserves of the deposit.INTRODUCTIONAvalon is in the unique position of owning and developing one of the world’s largest rare earth deposits in the Northwest Territories of Canada.The term Rare Earth Elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties. REE are not particularly rare and have a similar abundance in the earth’s crust to nickel, tin or tungsten. Unlike these better known metals however, the rare earths have little tendency to become concentrated into commercial ore deposits. When they do become concentrated, deposits of REEs usually display enrichment in one of two groups. The most commonly occurring deposits of REEs contain a sub-group of elements referred to as the “light rare earth elements” (LREEs), which include lanthanum, cerium, praseodymium, neodymium, and samarium. Less commonly, deposits of REEs contain the much more valuable sub-group of elements referred to as the “heavy rare earth elements” (HREEs), which include europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutetium. Yttrium and scandium most commonly occur in association with this second HREE sub-group. Generally, LREEs are produced from the mineral bastnaesite, and the HREEs have been produced from the minerals xenotime and monazite. LREEs continue to be produced from bastnaesite, however in the 1980s, China started production of HREEs from unique laterite clay deposits. China now produces approximately 95% of the world’s rare earths."

Jan 1, 2011

M INE production requires the coordination of the talents of men and the use of equipment. Mine operators maintain a continual surveillance of equipment, looking for improvements and modifications that will benefit them. Few give similar attention to the advances made in the education of mining engineers since they themselves graduated. That is not surprising. Education lacks the advertising budget available to manufacturers. A modification to improve a mechanical contrivance is advertised, and an advertiser's press releases get attention by publishers. The whole program for mining engineering education could be revolutionized and no one, except a few professors, would know about it. The Canadian Institute of Mining and Metallurgy's newly established General Commit-tee on Education can improve that situation. Nine groups of engineers in Canadian universities are trying to give undergraduates an education that will make them useful to the mineral industry as mining engineers. The tabulation offered here (Table I) is an analysis of the distribution of the undergraduate-teacher contact time.

Jan 1, 1963

By R. H. Wallis

Weighted moving-average contour maps have been constructed for molybdenum, copper and zinc using 7850 stream-sediment samples from 5430 square miles (14,063 sq. kms) of south-central British Columbia. Regional trends for molybdenum and zinc are northeast, north and northwest and those for copper are north and northwest. These trends are interrupted by zones markedly low in metals . The metal-rich trends cross rocks of different lithology and age and thus appear to be structurally controlled. The northeast trend may have exerted control on metal distribution at two different times.

Jan 1, 1978

By Andrew Gillam

Outline of Presentation ? AMEC overview ? Benchmarked companies ? GRI 3.1 Guidelines ? Best practice examples ? Report content and boundary ? Strategy and profile ? Environmental ? Social GRI G3.1 ? Gold Standard for Reporting ? GRI ? Global Reporting Initiative ? 1997 outgrowth of Coalition for Environmentally Responsible Economies (CERES) and UN Development Program (UNDP) ? Official collaborating centre of UNDP and works in collaboration with UN Global Compact ? Coalition of companies, business organizations, accounting firms, CSR consulting firms and nogovernmental organizations (NGOs) ? Mission: develop and disseminate globally applicable Sustainability Reporting Guidelines ? Now de facto CSR reporting standard; appeal lies, in part, with supported flexibility in reporting approach and scope ? Latest generation G3.1 (March 2011); includes expanded guidance for reporting on human rights, local community impacts and gender

Aug 1, 2013

By John G. Peacey, Leoncio Sevilla G., Ford. Kevan J. R., Erling Villalobos C.

"Kinross Gold Corporation’s Mantos de Oro (MDO) gold/silver mine in northern Chile currently processes 15,000 tpd of oxide ores through a mill, whole ore cyanide leach plant followed by a Merrill-Crowe refinery. With the expected depletion of these oxide ores in a few years a new sulphide mineral deposit, Ladera-Farellón has been identified to potentially replace existing ore reserves. The deposit contains approximately 0.5g/t Au, 6g/t Ag and 0.5% Cu. The principal sulphide mineral in the deposit is enargite (Cu3AsS4) which hosts the majority of gold and silver and the copper. Direct cyanidation testwork has shown the sulphide mineral is refractory with a low gold recovery of 36% and silver recovery of 45%. Oxidation of the sulphides is required to liberate gold and silver and allow recovery of copper as an important pay-metal. Therefore, at MDO a new metallurgical process route with oxidation as a pretreatment step is required for viable treatment of such new sulphide mineralized material with acceptable recoveries of pay-metals.Analysis of flowsheet options was completed based on bench-scale and pilot scale metallurgical testwork as well as with reference to existing studies and operations. The process options investigated assume concentration of sulphides by flotation, followed by either pressure oxidation, bacteriological oxidation or roasting. Preliminary evaluation of flowsheet options focused on process risk, operability, technology availability and the economics of the project with emphasis on use of the existing metallurgical plant to reduce capital cost. Operating costs for each process option were also included in the relative analysis.The challenges of treatment of MDO sulphides, principally enargite and pyrite for recovery of gold, silver and copper center on fixation of arsenic and sulphur capture with environmentally acceptable disposal of residue tailings. This environmental focus was included in the process option selection and comparative analysis.This paper presents a review of the process options considered and highlights comparative advantages/disadvantages of each process with associated environmental issues. Preliminary conclusions are drawn on roasting as a potentially favorable process option for the treatment of MDO sulphides."

Jan 1, 2009