Search Documents

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determination in a series of industrial campaigns. Some frother observations are described, including: concentration evolution down a bank, distribution between pulp and froth phases, and a mass balance around a circuit. Minute amounts of frother in recycle water were also measured.The contribution of frother and alcohol by-products in the analysis was generally additive for plants using aliphatic alcohol type frothers and decoupled for systems using glycols. Typically, U250C (polyglycol) was used at higher concentration (>10 ppm) than MIBC (aliphatic alcohol) (<10 ppm) or F-150 (polyglycol) (<3ppm).The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2007

By J. Asfahani

"The Schlumberger configuration used in geoelectrical sounding is slightly adapted here to obtain reliable data for both shallow and deep penetration depths from the same survey. In this configuration, two kinds of current electrode half-spacings are used: the first enables construction of vertical electrical resistivity sounding (VES) curves for shallow depths (<50 m), and the second for depths =250 m. For a given VES location, two field curves are measured and interpreted using two standard approaches. Practical characteristics of such a modified configuration are illustrated with two field applications in Syria. The first aims to characterize the structure of Quaternary and recent deposits in the Al-Ghab depression region, and the second deals with exploration for phosphatic sedimentary units in the Al-Sharquieh mine. La configuration de Schlumberger normalement employée dans les levés géoélectriques a été légèrement modifiée afin d’obtenir des données fiables à faible et forte profondeur durant le même levé. Dans cette nouvelle configuration, deux types de demi-espacements des électrodes sont utilisés : le premier permet le développement de courbes de sondage de résistivité électrique verticales (REV) pour les faibles profondeurs (<50 m), et le second atteint des profondeurs =250 m. Pour une localité REV donnée, deux courbes de champs sont donc mesurées et interprétées grâce à deux approches standardisées. Les caractéristiques pratiques de cette configuration modifiée sont illustrées par deus exemples d’application en Syrie. Le premier vise la caractérisation de la structure des dépôts Quaternaires et récents de la région de la dépression d’Al-Ghab, et le second traite de l’exploration pour des unités phosphatiques sédimentaires à la mine Al-Sharquieh."

Jan 1, 2009

"The standards set out requirements of the Toronto Stock Exchange for company’s providing information to investors, regulators and/or the media regarding their mineral properties. In addition, information contained in new releases, continuous disclosure documents [annual report], or other forms of communication [printed investor relations materials and electronic publications] are also subject to these standards.1.0 INTRODUCTIONThe disclosure of the results of exploration and development activity on mineral properties mustcomply with the requirements of the Toronto Stock Exchange Policy Statement on Timely Disclosure, theOntario Securities Act and all applicable policies and rules of the Ontario Securities Commission and anyother securities regulatory body having jurisdiction over an issuer listed on the Exchange. In particular,the requirements of National Instrument 43-101 must be followed.The purpose of the standards is to set out the requirements of the Toronto Stock Exchange when acompany provides information to investors, regulators and/or the media regarding its properties, whethersuch information is contained in a news release, a continuous disclosure document such as an annualreport, or other form of communication, including, but not limited to, printed investor relations material andelectronic publications such as Internet Web sites. These standards do not apply to prospectuses orlisting applications, the standards for which are contained in the policies and rules of the securitiescommissions and the Exchange. These standards are also not intended to establish requirements for thecontent of technical reports.Any information published by or on behalf of a company must comply with these standards. If acompany becomes aware of information published by others regarding its mineral properties which ismaterially misleading to investors, it should take appropriate action to correct such information orotherwise make it known that it is not responsible for publishing such information and does notnecessarily agree with such statements.Disclosure concerning mineral properties should identify the ""qualified person"" as defined in NI 43-101 who is responsible for the work conducted on the property and such person shall have read andapproved of the technical disclosure."

Jan 1, 2003

By Jeffrey Oke D.S.H. Oke, Craig J. Archibald, Anna P. Perry

Underground mining at the Diavik Diamond Mine (Northwest Territories, Canada) commenced in 2003 and has targeted four kimberlite pipe orebodies. The A154 North (A154N) pipe was mined using longhole open stoping with cemented and uncemented rock fill. During the later stages of mining, unique geotechnical challenges developed in the upper portion of the orebody, resulting in difficult ground conditions during secondary stoping. The two uppermost stoping horizons in A154N (A- and B-blocks) were located within the widest portion of the kimberlite pipe and were mined using a multi-panel retreat, overhand primary–secondary extraction sequence. Primary stopes were commonly advanced to near the top of each block prior to the initiation of secondary stoping. Ore development was excavated to full stope width, and secondary development initiated at the base of the block adjacent to mined-out primary stopes resulted in the formation of tall, slender hanging pendant pillars—locally up to 100 m high—laterally supported by frictional contact with adjacent cemented rockfill pillars. Beginning in 2015, differential vertical movements across the ore-waste contact of A154N pendant stope pillars were identified, and the extent and rates of movements increased significantly as secondary stoping progressed through to 2025. These conditions created significant challenges for the safe extraction of remaining stopes and raised concerns for deeper mining blocks if similar methods were maintained. This case study describes the factors contributing to the observed ground behaviour and outlines the strategic mine design modifications and tactical risk mitigation measures implemented to manage geotechnical risk in the remaining A- and B-blocks and to prevent recurrence in lower A154N mining horizons.

May 2, 2026

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company&apos;s business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010

By Waldbillig. D.

A baseline of the poisoning effect of hydrogen sulfide (H2S) fuel impurities on solid oxide fuel cell (SOFC) anodes was developed using polarization testing. After the baseline behaviour was characterized, tests to study the effect of various H2S concentrations on the rate and amount of cell voltage degradation and recovery were performed. Attempts were made to improve the rate and amount of recovery by various methods. Testing was very reproducible, but significant electrochemical performance degradation was seen after all H2S poisoning tests even at an H2S concentration of 0.1 ppm. Degradation is initially quite rapid, but after a period of time the rate of degradation levels off. After poisoning was complete, the H2S flow was stopped and the cells were allowed to recover. Some recovery was seen after poisoning, but cell performance was never fully recovered.

Jan 1, 2005

By K. Östcrdahl

We are developing a cost-saving and environmentally friendly process with low energy consumption to recover the metal content and recycle the acid from spent pickle baths. The metals are precipitated as metal fluorides, which can be turned into metal oxides and hydrofluoric acid by thermal hydrolysis. In the proposed process the solution is concentrated by nanofiltration and the metals are precipitated in a subsequent crystallization step. Different nanofiltration membranes have been evaluated in experimental batch tests. The membrane MPF-34 from Koch Membrane Systems offered both good flux and acceptable metal retention even after long periods of acid storage. The solubility of B-FeF3.3H20 has been measured at varying acid concentrations and at different temperatures. The solubility decreases with increasing hydrofluoric acid and nitric acid concentrations. This suggests that the crystallization process should be operated at high acid concentrations. The crystal growth rate of B-FeF3.3H2O is found to be quite low but increases significantly with temperature. This suggests that the crystallization process should be operated at higher temperatures (40 - 60°C). Within the project a pilot plant has been constructed where the spent pickle bath solution is concentrated by nanofiltration to the desired metal fluoride supersaturation, and B-FeF3.3H2O is crystallized in a 10 L continuous crystallizer.

Jan 1, 2006

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By K. Honkivaara, S. Junnikkala, J. Aho, K. Föhr, P. Lampinen

"Bubble area flux has been claimed to be a major tool to dimension flotation equipment. The paper describes laboratory scale (batch and 301 continuous cell using plant feed) and small-scale (1 ,8m3) industrial experiments with coarse-grained massive sulphide ore.Samples were taken with different froth thickness and air addition rates while the bubble size was measured with an UTC capillary device. Problems of averaging the bubble size measurements and the bubble area flux measurements are also discussed.Material balances were calculated using the commercial program BILCO. The flotation rate constants were calculated for pulp and for froth assuming that we can extrapolate the flotation rate constant of the pulp phase from tests using very thin froth thicknesses.The results indicate that the bubble area flux is not alone an adequate dimensioning tool. With fine sizes there was a nearly linear relationship between the bubble area flux and rate constant for constant impeller revolutions. For coarse sizes the form of the relationship is non-linear and seems to go through a maximum value. Thus the final flotation outcome is not a simple function of bubble area flux but depends on the particle size distribution and other more traditional flotation cell dimensioning variables. The effect of the froth residence time in the total recovery of coarse particles is large, but will not be treated in this paper."

Jan 1, 2000

By Hervé Toubon, Matthieu Davrinche, Jim Corman, Mamane Bello Boubacar Kinassa, Pierre Amadieu

Orano Mining maintains a significant level of Innovation and Development Research for its sites in Canada, Niger, Kazakhstan, Mongolia, and France. This effort is formalized within the six major thematic programs below, which include more than one hundred affiliated R&D projects:  Geological understanding, tools and methods for exploration  ISR technology (geology, modeling, mining development tools)  Mining technology (SABRE)  Ore treatment and processing (in particular via our Centre for Innovation for extractive metallurgy, CIME)  Environment (radiochemistry, modeling, tools and methods for remediation)  Digital Mine (sensors, transmission, database, and data modeling) This paper describes the main actions of these six programs, their stakes, and their progress. There is no single path leading to innovation but fostering an innovative context and a structured project approach are essential ingredients to successful development and industrial deployment. As a result, Orano Mining has, over the years, developed a disciplined methodology for R&D portfolio and project management. This methodology, presented here, targets a reduction in time to implementation while valuing both the expertise and the work in project mode.

Jan 1, 2020

By P. Botane, A. Cailleau

"Compagnie Miniere Esperance operates a gold primary ore body. The ore is processed through crushing, grinding and gravity concentration generating tailings with remaining fine gold. Analyses of the tailings proved a residual gold grade sufficient for a chemical treatment.As lab tests proved the technical feasibility of a pre-concentration using flotation, an on-site pilot operation has been carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for the industrial circuit sizing.Data collected during the pilot campaign have been used for calibrating a process simulator built with the USIM™ PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain a good fine gold recovery in a small amount of concentrate. A preliminary capital cost has been achieved to assess the flotation workshop profitability.INTRODUCTIONCompagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation in two stages: a top plant and a bottom plant. A “coarse” pond contains tailings of the top plant; this product feeds the bottom plant. Tailings of the bottom plant are stored in the “fine” pond.Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and meteorological conditions).It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility."

Jan 1, 2009

By C. Caners

One of the main uses of fossil fuels is in the transportation sector, leading to environmental consequences such as climate change. In order to move towards a more sustainable energy infrastructure, a transition must begin from fossil fuels to renewable fuels, derived from e.g. biomass. One means of facilitating this transition is to develop reforming technology that can extract hydrogen from a suitable fuel that is either fossil fuel or renewable in origin. The hydrogen would be feed to a &apos;fuel cell&apos; engine that would power the car, truck or bus. One reforming technology that is attractive for automotive applications is autothermal reforming (ATR). Autothermal reforming is the combination of steam reforming and partial oxidation, whereby a portion of the fuel is combusted using a sub-stoichiometric amount of air, and the resulting thermal energy drives the more desirable steam reforming reaction. ATR is attractive for fast start-up, rapid load following and ease of control. ATR also has the benefit of smaller volume and fewer peripheral requirements as compared to other reforming technologies. Recently, a bench-scale gasoline autothermal reformer (ATR) was constructed and tested. This ATR employs a novel design, consisting of three concentric annuli in order to promote heat transfer from the partial oxidation reaction to the steam reforming reaction. Concurrently, a CFD based model (FLUENT) of the ATR that considers the geometric complexity of the reformer was validated. In spite of the use of simplified kinetics, the model predicted well the observed trends in temperature and overall performance. This paper will discuss the use of the model to improve the design of the ATR. The impact of various system parameters upon performance will be investigated along with alterations in the geometry of the ATR. The various tradeoffs in performance and system volume/size will be highlighted in the context of a fuel cell power system.

Jan 1, 2005

By A. F. Matheson

"Bankfield Consolidated Mines, Limited, and Tombill Gold Mines, Limited, in the Little Long Lac area, Ontario, mined an orebody that was common to both. The discovery' of this orebody was made by surface prospecting in May, 1932, on Bankfield ground, following an original discovery made in the same manner on the same property on a small reef in Magnet lake in October, 1931. The production from the two mines between 1937 and 1942 was approximately 135,000 oz. gold from about 420,000 tons of ore, an average grade of 0.32 oz. a ton. Production was nearly equally divided between the two properties. Both mines are now closed, the ore exhausted.""The ore is mainly sheared and fractured greywacke and porphyry impregnated by silica and small amounts of metallic minerals. To a lesser extent there are definite quartz veins in the ore zone""(l). The metallic minerals present were principally pyrite, arsenopyrite, pyrrhotite, and native gold .As at other mines in the Little Long Lac area, an elongated, broad, deep trough of folded, steeply dipping volcanic and sedimentary rocks, striking roughly east-west and surrounded by younger granite, is host to the orebodies of the Bankfield and Tombill. In the immediate area of the two mines iron formation and conglomerate bands occur nearby both north and south of an intrusion of porphyry-Cliorite, suggesting repetition of beds and folding. Although considerable drag folding is in evidence, folding on the above scale has neither been proved nor disproved."

Jan 1, 1954

By Claude Bazin, Patricia Obiang

"The slurry density (pulp percentage of solids) and the size of the grinding media are often used for the optimization of an operating ball mill. In many cases a change of ball size is made at the slurry density used with the original ball size. But is the optimum slurry density changing with grinding media size? Laboratory grinding tests were conducted to answer that question and results indicate that more than likely there is no need to adjust mill slurry density when adjusting the size of a grinding media in a ball mill. Full scale behaviour could be different because slurry density affects the slurry transportation through the mill and the classifier operation.INTRODUCTIONOre preparation begins with a fragmentation step that liberates valuable minerals or exposes mineral surface to the environment. The size reduction step of a mineral processing operation is energy demanding and the optimisation of this process should always be an objective for the plant metallurgists. Various approaches could be considered for improving the operation of a grinding circuit. For a close grinding circuit an adequate tuning of the classifiers operation may lead to substantial savings (McIvor, 1988). Once a grinding mill is in operation, few variables remain to be considered for process optimization. The ball charge is usually maintained to achieve a target power drawn by the grinding mill motor. The rotation speed is seldom considered (McIvor, 1983; Bazin and Lavoie, 2000) as a change of mill speed usually implies a costly pinion change. If the liner and lifter configuration is critical for SAG and AG mills (Latchireddi et al., 2005), few discussions are available for ball mills (Fuerstenau and Abouzeid, 1985; McIvor, 1983). The mill feed size distribution can also be adjusted but this implies changing the upstream processes, which transposes the optimization process to another level. Modification to grinding media shape is a possible avenue (Cooper et al., 1994), but it remains that slurry density and grinding media size are probably the most frequently considered variables for the optimization of a ball mill."

Jan 1, 2007

By R. Pelletier, Herny. E., C. Allaire

Corrosion of refractory linings by molten metals is controlled by interactions between penetration and chemical reaction. Corrosion of aluminosilicates by molten aluminium is no exception. The early stage of corrosion can be described as a particular case of reactive wetting over a porous medium. Although the reactivity between aluminium and silica is great, which should improve wetting and penetration, the presence of air and the formation of a protective oxide layer disfavours initial penetration. This paper presents the results of an exploratory study on the effect of some parameters on the initial stage of aluminium penetration. Penetration kinetics and metal intrusion tests have been performed on alumina and silica powders with pure aluminium and Al¬5%Mg. Capillary models are used as tools of interpretation. Penetration kinetics tests had a poor reproducibility and the kinetics itself can not be explained very well by the capillary-tube-bundle model. On the other hand, a capillary model initially developed for ice intrusion into freezing soils produced predictions in reasonably good agreement with intrusion pressure measurements. The effect of particle size and alloy composition can be predicted using this model. However, the effects of temperature and powder chemistry need additional interpretations to be rationalised. An unusual resistance to penetration of silica powder by molten aluminium have been observed in a series of experiments. This led the authors to the strange conclusion that oxygen should be seen as an excellent non-wetting agent and that there might be ways to use it in industrial applications.

Jan 1, 2004

By Fathi Habashi, Ahmet Deniz Bas

"The mechanism of leaching of semiconducting minerals such as PbS, ZnS, UO2, etc., has been the subject of intensive speculation by hydrometallurgy researchers in the early 1950s who assumed the formation of intermediate surface complexes that could be neither separated nor identified by physicochemical techniques. The electrochemical theory of leaching introduced in the late 1960s resolved this problem by comparing the leaching process to a corrosion phenomenon similar to the corrosion of metals. Few years later, experimental evidence showed that anodic and cathodic zones are formed on the dissolving mineral although no electric current is imposed on the mineral during dissolution. A discussion of these findings is outlined.INTRODUCTIONIn the early 1950s researchers realized that kinetic studies for leaching ores are as important as thermodynamic calculations. It was also during this period that the concept of species adsorption on mineral surfaces has dominated the interpretation of the mechanisms of most reactions. This may have been due to the fact that many researchers of this period came from the mineral dressing sector and were influenced by flotation theories. However, when the knowledge of lattice defects and the semiconductivity of minerals became known and their importance in extractive metallurgy was realized, there was a need to explain the leaching reactions in light of these modern theories (Habashi, 1969, 1970). Semiconducting minerals of importance in metallurgy are two categories: the sulfides such as those of copper, lead, zinc, and the oxides such as those of uranium."

Jan 1, 2016

By C. J. Coulson, G. A. McKay, A. M. Cormie

"The Leitch mine, in the Beardmore area, Thunder Bay district, Ontario, is a part of the Leitch estate. It includes a group of patented claims, staked by P. A. Leitch of Port Arthur early in the century, along bands of jasper, hematite, iron-bearing slates, carbonatized schists, and greywacke, commonly known as 'iron formation'. The folding and shearing in these variably interstratified beds is a striking structural feature. The vein pattern is very definitely related to these structures.ROCKSThe rocks in the area are typical Keewatin lavas-greenstone-overlain by a series of Timiskaming sediments consisting of arkosic greywacke, iron formation, slate, greywacke, conglomerate, and greywacke, in this order from the contact. The sedimentary beds are generally conformable with the older rock contact except on local folds.Small intrusions of diorite occur as nearly vertical dykes and are believed to be of Algoman age. To the northwest of the mine there are larger intrusions of granodiorite belonging to the same period.Several dykes of quartz diabase up to 100 feet in width, striking generally north and south, with a vertical dip, cross the property. These have been classified by W. C. Laird as pre-Keweenawan in age. One of these dykes in particular is of importance for it cuts through the No. 2 vein and serves as a pillar when stoping. It is approximately 6 feet wide.The youngest rock type represented is a sheet of olivine diabase that extends over an area of thousands of square miles in and around lake Nipigon. It underlies most of this area and its outcrops form some of the most interesting topographical features, with fault scarps rising hundreds of feet. In the vicinity of the mine shaft the sheet is about 600 feet thick and extends from a depth of 1,871 feet to approximately 2,470 feet. It has a dense, hard, chilled margin and a sharp, tight contact. It intruded the sediments with very little lateral disturbance. The chief effect was baking, which darkened and hardened the greywacke near the contact. The sheet dips flatly to the cast."

Jan 1, 1954

By D. Bronkhorst, J. Rheault

"Backfill practices at the Williams mine have evolved significantly since underground mining began in 1986. The use of conveyors as a means of transporting fill material to stopes has been discontinued in favour of load-haul-dump equipment. The method of adding binder to the fill product has been refined along with the placement technique. Slurry preparation has been fully automated and flyash is now included as a binding agent. Surface preparation of the fill product has evolved substantially with the quarry operation coming into full operation and the construction of pennanent crushing, screening, and storage facilities. Company personnel have replaced all contracted labour involved in backfill operations. Some changes have been made to achieve a higher standard of quality control while others were implemented as a matter of cost reduction. BackgroundThe Williams mine is one of three mines operating at the Hernlo gold deposit, located 40 km east of Marathon, Ontario, along the north shore of Lake Superior. Daily production at the mine is 6000 Ud yielding an annual gold production of approximately 500 000 oz. The orebody extends from surface to a depth of 1300 m dipping north at 70 degrees. The average orebody width is 25 m, but varies from 45 m on the eastern boundary to about 10 m at the western probable limit and at depth. Proven and probable reserves currently stand at 32 million tonnes grading 6 g/t.The Williams orebody has been divided into four separate mining zones: the A-zone, the West-of-Dyke zone, the B-zone, and the C-zone (Fig 1). Ore production originally was from the A-zone open pit operation while the A-zone and B-zone underground workings were being developed. The mining method employed underground is blasthole open stoping with delayed rockfill. Mining block dimensions are nominally 20 m along strike by 25 m high. Stope extraction is sequenced to achieve a relatively short pillar life and 100010 ore recovery. Pillars are extracted as soon as the adjacent primary stopes are two cycles ahead. Primary stopes are filled with consolidated rock fill after mining. This allows pillars to be blasted right against the consolidated fill, but also requires that the fill be self supporting to a height of 30 m.The Williams mine places approximately 1.4 million tonnes of rockfill and 50 000 tonnes of binding agents each year, with about three quarters of the fill placed being consolidated. The consolidated fill placed at the Williams mine contains Portland cement and flyash as binding agents."

Jan 1, 1994

By Douglas Macaulay

"The Work contains the personal views and opinions of the Author and in no manner should it be construed as reflecting the official position of Export Development Canada. The Author makes no representation or warranty with respect to the accuracy or completeness of the contents of the Work and specifically disclaims any implied warranties, merchantability or fitness of use for a particular purpose". Export Development Canada ?Canada?s official export credit agency, established 1944 ?Mandate to support export and foreign investment ?Financially self-sustaining, AAA rated borrower ?Services include: Financing (FIN), Political Risk Insurance (PRI), Contract Insurance & Bonding (CIB), Accounts Receivable Insurance (ARI) ?A trusted partner in troubled times

May 1, 2010