Search Documents

By A. Shakoor, T. P. Gautam

The long-term slaking behavior of clay-bearing rocks in the field can be quite different than the short-term slaking behavior in the laboratory. To assess this difference, 12 replicate samples of each of 20 clay-bearing rocks, including 5 claystones, 5 mudstones, 5 siltstones, and 5 shales, were exposed to natural climatic conditions for 12 months. After each month of exposure, one replicate sample of each rock was removed from natural exposure and its grain size distribution was determined. Disintegration ratio (DR), defined as the ratio of the area under the grain size distribution curve of the slaked material for a given rock to the total area encompassing all grain size distribution curves of the tested samples, was used to quantify the amount of disintegration under natural climatic conditions. DR values of naturally exposed samples were then compared with the corresponding values of second-cycle slake durability index (Id2) determined in the laboratory. The relationship between Id2 and DR after, 1 month of exposure, exhibits an R2 value of 0.65 but the relationship deteriorates when DR values for 6 and 12 months of exposure are used, with R2 values of 0.63 and 0.25, respectively. However, when DR values for laboratory samples, computed from grain size distributions of slaked material after second cycle, are compared with DR values of naturally exposed samples for the three periods of exposure, the relationship improves with the corresponding R2 values being 0.61, 0.71, and 0.41. These results suggest that DR may be a better parameter for assessing the long-term disintegration behavior of clay-bearing rocks than Id2.

Jan 1, 2015

By George Hope, Brigitte Lacouture

"The Red Dog Mine has increased mill throughput for most years since startup. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Late in 1999, a new circuit was designed with increased flotation capacity while simplifylng the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, twentyone (21) Outokumpu OK50 mechanical flotation cells and four (4) 3.66m dia. column cells will be added to the current flotation circuit. The VIP (Value Improvement Program) Mill Optimization project is also addressing thickening, water treatment and power issues and has a total budget of $US105 M. Startup of equipment will be phased in to minimize the impact on current operations and is expected to be complete by the end of Q3-2001.INTRODUCTIONRed Dog Operations started production in November 1989. The mine is located above the arctic circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred (100) days of open seas. Typical of sedimentary exhalative deposits, the metallurgy proved to be challenging and coupled with many mechanical shortcomings, the initial few years were very difficult. The start-up issues were slowly resolved and in 1998, a major grinding expansion, the PRI (Production Rate Increase) project, was completed. The project was designed to allow a 40% increase over the 1995 throughput. In 2000 mill throughput was 3,050,000 tonnes to produce a total of 960,000 and 140,000 dry tonnes of zinc and lead concentrates respectively, making Red Dog the largest zinc concentrate producer in the world. To address a shortage of flotation capacity remaining from the PRI grinding expansion, a project designated as the VIP (Value Improvement Program) Mill Optimization project was initiated. The mill optimization project is targeted to produce 1,100,000 tonnes of zinc concentrate at 56% zinc grade and 87% zinc recovery. The project will add twenty-one (21) Outokumpu OK50 (50m3) flotation cells, four (4) 3.66mO column cells and address water treatment, thickening and power generation capacities."

Jan 1, 2002

By G. F. Flaherty

THE property of Tashota Goldfields, Limited, in the Lake Nipigon area, Ontario, is located about 4 miles west of Onaman lake and 16 miles by winter road south-southeast of Tashota station on the transcontinental line of the Canadian National railways. The mine, formerly developed to a limited extent under the name of Tashota Gold mine, has, since late in 1933, been under the management of Minefinders Limited, who, in 1935, brought it into production on a 60-ton per day basis. During the winter of 1934-35, the writer was geologist at the property. The geological structure in the immediate vicinity of the mine workings lends itself well to analysis on the basis of the mechanical principles of folding. Since structure is of prime importance in the localization of the ore-shoots and of the host shear-zones at the property, the correlation of all structural details and their mechanical interpretation forms a working hypothesis of structural control for the direction of exploration and development work. It is believed that the structural relations here set forth may be found applicable in part, or at least suggestive, in working out the relations of ore-shoots to structure in the Sturgeon River area to the south, and in the Little Long Lac area to the southeast (Figure 1).

Jan 1, 1936

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

By J M. Gibbs

Craigmont Mines Limited mine 50,000 tons of ore and waste per day from the open pit at Merritt, British Columbia. An electric-powered "down-the-hole" drill, a diesel-powered rotary drill and two electric-powered rotary drills have been used. All primary drilling, as a result of cost and operating experience, is now performed with two electric-powered rotary drills. Trials with various loading techniques have increased the amount of AN-FO and decreased the amount of commercially prepared slurries used for primary blasting. Approximately 95 per cent of the primary blasting is accomplished with AN -FO, mixed at the hole. Introduction THE Craigmont mine is located near the village of Merritt, B.C., 240 miles northeast of Vancouver. The concentrator has been in production since September of 1961. Craigmont is a combined open-pit and underground operation. To date, slightly more than 95 per cent of the mill feed has been mined from the open pit. As underground development proceeds, the ore requirements from the open pit will decrease. The average milling rate from September, 1961, to April, 1964, was approximately 4,900 tons per day.

Jan 1, 1965

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By A. Torkian

Process water from production of concentrates in Meydook copper sulfide mine is transferred to the 8.3 million m3 tailings dam and a water retention pond after initial thickening. Elevated concentrations of heavy metals, sulfate, and TDS and decrease in pH as well as seepage into the aquifers have been the concern of the regulatory agencies since the start of activities. In this paper the results of a 6-month monitoring program from 4 wells are presented. The wells were located approximately 1.5 km from downstream of tailing dam (0.4 km from water retention pond) as well as upstream background well (2.28 km from water retention pond and 1.27 km from tailings dam). The objective was to study possible effect of accumulated tailings on the groundwater resources. Water levels in sampled wells were on average between 20 and 40 m. Results showed high levels of lead (5 ppb), copper (0.17-0.46 ppm) and selenium (73.1- 29.1 ppb). High levels of selenium and lead were partly due to natural geological settings of the area with high levels present in unaffected soils in the vicinity including water wells of villages upstream of mining operations. High copper levels were attributed to both mining operations as well as deposition from particulate air deposition onto the soil and transport to ground water by rain.

Aug 1, 2013

By Ruy L. Rodrigues

Vale is in the early stages of commissioning its Onça Puma nickel operations. The project is meant for the production of 58,000 tpa of nickel contained in ferro-nickel, substantially contributing to the company?s vision to achieve world leadership in the nickel business. Mineral resources will be exploited from the homonymous deposits in the Midwest of state of Para, Brazil ? some 100 km southwestwards from the company?s Carajás iron ore properties. Resources as of 83 Mt at 1.73 % Ni will sustain a mine life of approximately 40 years. The property was acquired in late 2005 and Vale has since extended the engineering studies and proceeded with the implementation. Nickel will be mined from saprolitic ore at a rate of approximately 10 Mtpa (ore plus waste) in early years ? ramping up to some 15 Mtpa 7 years later ?, to feed the plant at a rate of 2.5 Mtpa. The process uses conventional RKEF (Rotary Kiln Electric Furnace) pyrometalurgical route whereby the ore is homogenized, calcined in rotary kilns, melted in electric furnaces and further refined to ferro-nickel. The plant has been designed and constructed applying the latest available technology, aligned with Vale?s vison to exceed the highest existing standards for environmental control, health and safety and productivity in the industry. Total investments in these operations are anticipated to correspond to USD 2.3 Bi and will materially contribute to the regional development and well being of the nearby communities and other stakeholders.

May 1, 2010

By F. R. Deluca

"ClassificationClassification is a combination of mechanical and hydraulic operation which separates a pulp into two portions according to their respective settling rate. The finished product, the overflow, is removed from the other product, sand, which requires further grinding.Pulp is the uniform suspension of solids in a liquid. Overflow is the fines and therefore the more slowly settling portion of the pulp which is carried over the top of the classifier by the flow of water; sand is the coarser and more rapidly settling portion of the original pulp which is discharged from the classifier by the mechanical action of the rakes or conveyed out by a ""screw"" .Selective classification is classification that has for its object the concentration of the heavy constituents of the original pulp in the sand product so that it may be ground finer than the lighter constituent.Classification is used as follows:I. To make a size separation, for example, a sand-fines separation so that each product may be given a different treatment.2. For closed circuit grinding so that the maximum size of particles entering the circuit is limited, and so that the useful work is increased by enabling the mill to operate mainly on the particles that require the reduction.3. For differential grinding of the heavy mineral constituent and the gangue. In this case, the heavy mineral is concentrated in the sand product and is reduced further, while the lighter gangue material overflows the classifier.The selection of the proper size and type of classifier is determined by the function required, the character of the ore, and the tonnage to be handled, the initial cost and the operating cost."

Jan 1, 1989

By H. R. Wilson

"This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1988. The program was developed in response to the terms and conditions of the Water Licence issued to the mine in 1981 by the Northwest Territories Water Board. Echo Bay Mines Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle.The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that the total containment concept would require reevaluation since discharge from the pond would be required within a few years. During the initial years of production, an investigative program was established to determine the most effective means for treating the tailings pond water. This program incorporated both laboratory studies as well as monitoring of the tailings pond contents and environmental conditions as the impoundment area was filling. The program showed that natural degradation phenomena, if properly utilized, are effective in lowering the concentrations of all contaminants to within Licence limits with the exception of arsenic. To ensure compliance with arsenic limits, an iron salt was added to cause arsenic to precipitate from solution in the tailings pond.As a result of our studies, the tailings management system finally implemented at Lupin Mine includes the following components:Tailings pulp retention cells constructed by dyking off one end of the tailings impoundment area.Two tailings ponds in series operated in a sequential decant and fill fashion.An iron salt solution preparation and metering system.A syphon system into which the iron salt solution is injected as the contents of the first pond are decanted into the second pond.A second syphon system for decanting the contents of the second pond to the receiving streamThis paper discusses the findings and conclusions of the waste management investigative program, describes the civil work completed to reach our final operating scenario, describes the sequence of operating the treatment system, reviews performance data, and comments on abandonment and restoration of the tailings impoundment area."

Jan 1, 1989

By V. Thangadurai

The critical problems in commercialization of the present solid oxide fuel cells (SOFCs) and useful electrical and physical properties of IT-SOFCs electrolytes are discussed briefly. The conductivity behavior of the perovskite-type and perovskite-related structure metal oxides are summarized. Perovskite-type La0.9Sr0.10ao.8Mgo.203_8 (LSGM) exhibits high ionic conductivity of 0.1 S/cm at 800 °C. In order to improve the electrical conductivity of LSGM and the In analogue of LSGM, substitutions have been made at the A-and B-sites. Substitution of trivalent La3+ by isovalent Pr3+ in LSGM and La09Sro ilno.sMgo.202.85 (LSIM), yield new mixed conductors. Among the investigated compounds in the present study, La0APro.4Sro.21no sMgo.2028 exhibits the highest total electrical conductivity of 3.2 x 10-5 S/cm at 200 °C in air with the lowest activation energy of 0.44 eV (200-700 °C). LSIM and Pr-substituted LSGM and LSIM perovskites show p-type electronic conductivity in the oxygen partial pressure range 10-5 ? 0.21 atm at 750 °C. The perovskite-type solid solution SrSn1-xFex03 exhibits compositionally driven phase transitions. For example, compound of the composition x = 0 to 0.3 crystallizes in an orthorhombic GdFeO3-like perovskite structure, where as that of x = 0.4-0.9 crystallizes in simple cubic SrTiO3-like, and that of x = 1 in orthorhombic structure. The electrical conductivity of SrSn1_xFex03 increases with the increasing Fe content and reaches a value of about 10-1 S/cm at 25 °C in air for x = 1. Compounds with low Fe content exhibit both ionic and electronic conductivity, while the higher Fe content 0.5) perovskites are electronic conductors over a wide range of oxygen partial pressure of 10-22? 0.21 atm at 750 °C.

Jan 1, 2005

"The first SkimAir flash flotation cell was installed in Outokumpu’s Hammaslahti Copper Concentrator in 1982 to prevent overgrinding of soft sulphides in the milling circuit. Since this first installation the popularity of the flash flotation has fluctuated depending on metal market conditions and regional preferences. Units have been installed in many commodities including copper, lead, gold, PGMs, silver and nickel. Though it has been successfully employed in many operations around the world, flash flotation technology is still not well understood by many in the mining industry. This paper will discuss aspects of flash flotation flowsheet development along with some of the metallurgical and engineering considerations required to successfully incorporate flash flotation into new or existing milling circuits. This paper will also try and debunk some of the myths that exist around flash flotation cells and their operation. Case studies of flash flotation implementation will be discussed.IntroductionModern flash flotation technology was developed several decades ago by Outokumpu, with the first commercial installation of this technology being at the Hammaslahti concentrator in Finland in 1982 (Kallioinen & Niitti, 1985). This was a relatively modestly sized SK80 cell producing final grade copper concentrate directly from the flash flotation cell operating in the grinding circuit. Since that time the size and number of flash flotation cells installed globally has grown considerably to the point where today, it is a widely known application of flotation technology for amenable ores. Owing to their long history in developing the technology, Outotec are the market leader with their SkimAir range of flash flotation cells. Though there is a general awareness of flash flotation process in the mineral processing industry, there is a lack of detailed understanding of the process and the benefits it can provide to new and existing operations."

Jan 1, 2017

By A. R. Byers

"This paper describes the distribution, occurrence, and paragenesis of known sulphide deposits within an area bounded by longitudes 102°00' to 106°00' west and latitudes 54 ° 301 to 57 °00 1 north. The Precambrian bed-rock which outcrops over all but the southern fringe of the area con- . sists of regional metamorphic assemblages ranging from low grade or green schist facies to high grade or amphibolite-granulite facies. The areas . of low-grade metamorphism correspond to 'islands' of volcanic rocks which are surrounded by highgrade paragneisses and migmatites. Intrusive rocks range in composition from ultrabasic to granitic and may be divided into syntectonic and posttectonic sequences. The average composition of the former is granodiorite and of the latter quartz diorite.The massive sulphide deposits fall naturally on basis of mineral content into the following divisions: ( 1) pyrrhotite and / or pyrite, (2) sphalerite and/ or chalcopyrite plus iron sulphides, (3) sphalerite and galena, ( 4) sulphide-bearing pegmatite, and (5) nickeliferous pyrrhotite and / or chalcopyrite. The deposits of iron sulphides are ubiquitous. Ratio of pyrrhotite to pyrite is fairly constant for individual deposits, but their areal distribution appears to be independent of the nature of the enclosing rock and grade of regional metamorphism. All deposits containing ore-grade quantities of base metals have been concentrated at favourable structural locations. Copper-zinc and lead-zinc deposits appear to be associated with syntectonic granodiorite with the lead-zinc concentrations confined to calc-silicate gneisses. Copper-nickel deposits show a close relationship to post-tectonic gabbros and pyroxenites. The paragenesis is more or less the same for the majority of deposits, with iron sulphides and sphalerite being introduced early and followed by chalcopyrite and galena. Some vertical and / or horizontal zoning is apparent in a few deposits. Temperatures of formation and origin of the deposits are briefly discussed."

Jan 1, 1960

By Linlin Tong, Xiangling Song, Guobao Chen, Zhenan Jin, Hongying Yang

Biooxidation of a high arsenic-bearing refractory gold ore was investigated to determine the arsenic removal efficiency by the cultured bacteria and to examine the effect of biological pretreatment on subsequent gold cyanidation. The biooxidation pretreatment process utilizes the ability of adapted acidophilic bacteria to oxidize pyrite and arsenopyrite and release the encapsulated gold. The released gold can be efficiently extracted by the subsequent cyanidation process. The biooxidation experiments were conducted with cultured bacteria using various sizes of agitation tanks. Leaching results showed that over 96.26 % arsenic extraction could be obtained from this ore after 6 days of bioleaching with continuous stirred tank reactor (CSTR). Gold extraction during the cyanidation process was increased from 29.35% to 96.71% after biological pretreatment. The content of arsenic in the biooxidation residue was reduced to below 0.3%. The transformation process of As was considered as [AsS]2- ? As (?) ? As (?) during the biological pretreatment.

Jan 1, 2014

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By V. G. Papangelakis, G. A. Moldoveanu

"Rare earths adsorbed on clay minerals are easily recovered via ion exchange during leaching with inorganic monovalent salt solutions. The leaching efficiency of various salts at 0.5M and 25°C was investigated as a function of cation type and salt system (sulphates vs. chlorides). (NH4)2SO4 was identified as the lixiviant of choice and a procedure was established to investigate the influence of lixiviant concentration, temperature, pH and agitation on desorption kinetics and REE extraction levels. It was determined that the kinetics were fast and the optimum leaching conditions (for >80% total REE extraction) required pH below 5 and moderate temperatures (<50°C). INTRODUCTIONRare earth elements (REE) are at the core of numerous advanced applications due to their various uses in high strength permanent magnets, lasers, automotive catalytic converters, fiber optics/superconductors, and electronic devices (as phosphors in TVs and display screens for computers and cell phones). Because of the ongoing development of new technologies, there is an increased demand for REE in the international market, with emphasis on identifying new resources to insure an adequate supply for present and future use. World production of rare earths is dominated by China, the United States and Australia; however, in terms of resources, China dominates the world potential with reserves estimated to be over 90% of the total (Chen, 2011).The main commercially significant REE sources, as reviewed by O’Driscoll (1991) are bastnasite (carbonate) and monazite (phosphate) minerals, containing up to 70% wt. rare earth oxides (REO). In spite of being high grade, these ores are associated with elevated recovery costs due to difficulty in mining, separation and beneficiation. Moreover, aggressive conditions are required to solubilize the REE from the mineral, such as leaching with hot, concentrated acids or baking in 70% NaOH (Gupta & Krishnamurti, 2005)."

Jan 1, 2012