Search Documents

By R. E. Whitehead

"Abstract - Alkali-alumina and MgO-alumina plots are an effective instrument for displaying chemical and mineralogical compositions of altered and unaltered rhyolites and rhyodacites. They reveal that most supposedly unaltered rhyolites, apart from those of Cenozoic age, have undergone losses in Na2O and gains in K2O. The extreme loss of Na2O from highly altered rhyolites immediately adjacent to VMS deposits is strikingly illustrated by alkali-alumina plots. MgO/Al2O3 vs. K2O/Al2O3 diagrams display a strong negative correlation between MgO and K2O that results from the conversion of sericite to chlorite. A similar negative correlation between MgO and whole-rock d18O is apparent on plots of these two parameters. Alkali-alumina plots underscore problems in selecting appropriate precursor compositions required for mass-balance calculations. Molar ratio plots are a viable alternative to such calculations. Sommaire -Les diagrammes alcali-alumine et MgO-alumine constituent un instrument efficace pour la représentation des compositions chimiques et minéralogiques des rhyolites et rhyodacites altérées et fraîches.Ces diagrammes révèlent qu’à l'exception de celles d’âge Cénozoïque, la plupart des rhyolites qualifiées de fraîches ont subi une perte de Na2O et un gain de K2O. L’intense perte en Na2O que l’on note dans les rhyolites fortement altérées associées aux gîtes de type SMV est particulièrement bien mise en évidence par le diagramme alcali-alumine. Le diagramme MgO/Al2O3 vs. K2O/Al2O3 montre une forte corrélation inverse entre le MgO et le K2O due à la conversion de la séricite en chlorite. Une corrélation inverse analogue entre le MgO et le d18O de la roche totale s’observe sur un graphe comparant ces deux paramètres. L’usage du diagramme alcali-alumine fait ressortir combien il peut être difficile de choisir un précurseur de composition appropriée pour des calculs de balance de masse. Les diagrammes de rapport molaire constituent une alternative à de tels calculs."

Jan 1, 2006

By Marcel Labbé

La largeur de l?armature peut être modifiée selon les besoins du client entre 48 " et 64" de largeur totale, donc 2 sections de 24" à 32". Ceci permet à l?opérateur d?effectuer le démantèlement de l?équipement pour le déplacement dans les endroits restreints. Le déménagement d?un niveau à un sous-niveau devrait se faire dans un quart de travail de 8 heures. L?option de largeur permet au client de choisir un équipement adapté à son environnement de travail (1). La largeur de la table de forage peut être modifiée selon les besoins du client entre 48" et 96". Cette particularité permet une meilleure stabilité, et plus de précision dans le forage (2). Il y a 4 pattes hydrauliques à chaque coin pour la stabilisation lors de forage (3). La table de forage a 360° d?angle de forage sur 3 côtés du transporteur. La table peut sortir de chaque côté du transporteur de 40 ½" à partir du centre du transporteur pour faciliter la mise en place de la foreuse dans les endroits difficiles d?accès. La plage de forage est considérablement agrandie. Cette caractéristique qui fonctionne hydraulique, permet à l?opérateur de forer sans être obligé de changer la position du transporteur pour des changements de trous. Tous les types de foreuse peuvent être installés sur cette table de forage (4). Sa petite dimension lui permet d?accéder, par des monteries de 30" de diamètre, à des sites de travail de 2,5 mètres de hauteur et largeur. C?est un équipement adapté aux gisements filoniens. Ce genre de gisement est de moins en moins rentable pour les compagnies minières. La mécanisation des ces gisements va permettre de les rentabilisés en augmentant la productivité et la santé du travailleur, en réduisant la dilution (5). Les manettes de contrôle de la foreuse, les mouvements de la table de forage ainsi que le déplacement du transporteur ont été installés selon les recommandations d?un ergonome. Des recherches ont été effectuées par ce spécialiste sur les cas d?accident survenus avec l?utilisation de ce genre d?équipement. Il a déterminé les positions le plus confortable que l?opérateur doit prendre pour éviter les douleurs prolongées (6). Le système de roulement est composé de 4 roues pleines installées sur 4 planétaires de 9000 à 15000 livres de capacité munis chacun d?un moteur hydraulique. Des freins ont été installés sur les planétaires pour assurer la sécurité de l?opérateur et faciliter le positionnement du transporteur lors du forage. Des roues rétractables peuvent être installées pour faciliter l?accès sur rail (7). Ce transporteur peut être alimenté par une puissance électrique plutôt que par une puissance pneumatique. Cette puissance électrique est fournie par un Power Pack qui transforme l?énergie en puissance hydraulique. Ce type d?alimentation est employé lors du forage de développement, mais il peut aussi être utilisé pour le forage long trou. Cet avantage permet au client qui a un problème de pression d?air d?utiliser l?électricité. Par contre si vous utilisez l?électricité mais que dans un secteur isolé le gros courant électrique n?est pas accessible vous pouvez utiliser votre équipement en utilisant la puissance pneumatique. Le changement d?alimentation énergétique se fait facilement (8). Cet équipement est construit pour effectuer 4 types d?activités : forage de développement de niveau et sousniveau avec l?installation d?un bras porteur, forage et pose de câbles d?encrage pour soutènement de terrain, forage de production long trou et forage de monterie ascendante et descendante. L?avantage est que vous investissez dans un seul équipement au lieu de 2 ou 3. Cet avantage vous fait économiser dans votre budget d?équipement. En plus cet équipement est construit pour de dure travaux et ne contient aucun système électronique (9).

May 1, 2001

By J. Fujioka, Y. F. Gu, C. Cui, D. Ping, A. Sato, H. Harada

"A new kind of cast & wrought (C&W) Ni-Co base superalloys named as ""TMW alloys"" are developed recently for compressor or turbine disks of gas turbine engines in High Temperature Materials 21 Project at National Institute for Materials Science (NIMS) in Japan. These Ni-Co base superalloys combine the characters of two kinds of y- y' two-phase alloys (Ni-base and Co-18at%Ti alloys) and have higher tensile strength and creep resistance than C&W UNDIMET 720Li superalloy."

Jan 1, 2006

By Kilmar Mine

The Kilmar dolomitic magnesite deposit~ in sourhwesr Quebec lie in Grenville Province sedimentary rocks that strike north and dip steeply west. The sediments comprise quartzitic, carbonate and argillaceous members. The middle or carbonate member hosts the magnesite and, like the two other members, has been intensely mewmorphosed. Magnesite occurs as lenticular shaped zones of altered limestone and is mixed with 5 to 30% dolomite crystals. Diopside, serpentine and mica are common accessory minerals. Magnesite appears to have formed from merasomarism of all or part of the carbonate member due to intrusion of hot magnesia-rich solutions. Magnesite is mined from a 490 m vertical shaf1 and is milled and burned into clinkers, which then are shipped 10 pyroprocessing industries around the world.

Jan 1, 1984

By A. B. Cron, R. MacPhail, L. Melis, K. Armstong

"Mt. Milligan is a porphyry gold/copper deposit in north-central British Columbia. Diluted and mineable drill-indicated reserves total 449 million tons at an average grade of 0.013 oz gold/ton and 0.19% copper. Large-scale commercial development of the deposit will make Mt. Milligan Canada's third largest gold mine.Metallurgical investigations for the Mt. Milligan project were done in three phases: scoping tests in the first half of 1989; bench-scale work from October 1989 to April 1990; and a pilot plant program in May and June 1990. Various process alternatives for the recovery of gold and copper are described and results are presented. Net smelter return evaluations led to the selection of optimum process conditions for maximizing revenue from gold/copper flotation concentrates.The selected flotation circuit and basic design criteria are described. Forecast average recoveries over the presently-defined 20-year project life are 75.2% for gold and 90.5% for copper in a copper concentrate averaging 17.6% copper and 1.0 oz gold/ton. 1.0 PROJECT LOCATIONThe Mt. Milligan porphyry gold/copper deposit is located in northcentral British Columbia, 150 km north of Prince George, British Columbia. The site is at an elevation of 1,100 m in an area of logged, gently-rolling topography. Nearby communities include MacKenzie and Fort St. James. Climate in the area is moderate and there is direct road access to the property. A location map is presented in Figure 1-1."

Jan 1, 1991

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007

By H. Chaouki

The aim of this work is to simulate the forming process of a green anode. For this purpose, a nonlinear compressible viscoelastic constitutive law is presented. The concept of natural reference configuration is considered. Within an isothermal thermodynamic framework, a Helmholtz free energy is proposed to take into account the nonlinear compressible deformation process occurring between natural reference configuration and current configuration. A dissipation potential is introduced in order to characterize the irreversible aspect of compaction process. Thus, the constitutive law is formulated through two equations: 1) an expression of Cauchy stress tensor and 2) a differential equation characterizing the evolution of the natural reference configuration. Material parameters are assumed to be a function of the bulk density. This allows capturing the micro-mechanical phenomena within the chosen macroscopic approach. An experimental study based on compaction tests is carried out in order to characterize the mechanical behaviour of the anode paste. A user's material VUMAT subroutine for finite element dynamic explicit analysis has been developed and implemented in the ABAQUS commercial software. To evaluate the model predictive capability, numerical simulations of the compaction forming process of anode paste were performed. Simulation results show that the constitutive law predicts the experimental trends and gives interesting physical responses. This constitutes a first step toward making a benchmark with experimental results on the forming process of anode paste.

Jan 1, 2011

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978

By Francis Chachula, Niel Erasmus

"In 2002, Titanium Corporation Inc. focused its attention on the development of a process for the recovery of valuable heavy minerals, including zircon and titanium bearing minerals from oil sands froth treatment tailings. The development of a process flowsheet to recover the titanium and zircon minerals from the Athabasca oil sand tailings has evolved through many laboratory, bench and pilot scale iterations.Initial development work focused on so-called ‘beach sand’ material, which is tailings material deposited over a period of time close to the tailings pipe discharge. The derived process flowsheet primarily consisted of gravity concentration stages, which is typical of all mineral sands operations. Titanium Corporation’s business plan calls for the utilization of tailings directly from the tailings pipeline – the process developed around the beach material is therefore risky as it differs from the live tailings in a number of aspects, with the effects on the process unknown. Titanium Corporation successfully obtained an intermediate product through a ‘bulk sampling plant’ coupled directly to an Oil Sands operator’s froth treatment tailings pipeline, during the summer of 2005. Subsequent further processing of this material resulted in poor separation or concentration of the heavy minerals due to a number of reasons. A more effective process flowsheet had to be developed.The newly derived process is basically a marriage between mineral sands technology and oil sands technology that can economically concentrate and recover the heavy minerals and entails the incorporation of a flotation process that takes advantage of the entrained bitumen in the feed to separate the heavy mineral fraction from the quartz gangue This paper will describe the newly derived process as well as the successful results of a subsequent on-site concentrator pilot campaign completed during the 3rd Quarter of 2006."

Jan 1, 2008

By Chris Twigge-Molecey

Demand for metals will continue to grow as global population numbers and prosperity levels steadily increase. Consequently, there will continue to be a need to design and construct new metallurgical plants. Business success in general requires projects to be financially successful and return appropriate value to their owners. However, in the metals industry, private and public sector financing sources have become very sensitive to the perceived inability of projects to contain costs and meet other business objectives. Thus, the capital for projects has become more difficult and expensive to obtain. It is instructive to note that Ernst and Young (2011) identified that: “Delivery of predictable project results bestows competitive advantage and market confidence to those corporations who successfully instill this discipline”. The implication for future projects is that they must be systematically developed to minimize perceived risks—and more importantly—to demonstrate that the risks are managed to achieve the business case. Then, provided that the project has been developed in a well-structured way, project success can again be defined as a project with: a final cost within 10% of the budget approved at the end of FEL3, when the project is properly defined and the permit conditions are agreed upon; a start-up date within three months of the definitive, scheduled startup date; production levels at 85% of design capacity within a year of starting commercial operation; production meeting the target environmental restrictions; and with zero lost time accidents during construction and startup. The plant design is one of many integrated activities required to achieve these objectives. This book represents a valuable link between the existing engineering literature that encompasses a wide range of engineering fundamental textbooks and design manuals and the project management literature such as the Project Management Body of Knowledge, or PMBOK® (Project Management Institute, 2014). It is evident throughout this book, that the design team is a small but essential part of a much larger project team comprising the project management, construction management, and construction contractor staff. Design activities must be regarded and managed as part of the integrated whole, with two fundamental links throughout the design process:

Jan 1, 2015

By L. Louis

High resolution X-ray computed tomography imaging (with voxel size 48 µm) was conducted on various sandstone samples with different initial degrees of heterogeneity. All samples were imaged intact, and some after having developed localized compaction features in conventional triaxial experiments at high confining pressure, i.e. in the shear enhanced compaction domain (Wong et al., 1997). Our analysis of heterogeneity from X-ray CT data is based on the use of the coefficient of variation d =s /µ (s being the standard deviation and µ the average value). The coefficient of variation was shown by Otani et al. (2005) to be a convenient indicator of material heterogeneity in CT images of experimentally deformed sand piles. The authors reported differences in d before and after their experiments, and interpreted these differences as the effect of grain crushing resulting in more even material distribution within the voxels, hence in lower d values. The same concept was used by Louis et al. (2006) to image contrasts in d values throughout a volume of rock that had developed compaction bands in triaxial laboratory testing, knowing that the bands that had formed could be identified by visual inspection but not on the X-ray CT images. This study resulted in a radically enhanced image of the discrete compacted zones within the CT-scan series, whereby more deformed areas showed relatively low values of coefficient of variation due to grain crushing and pore collapse, as compared to nominally undeformed areas.

May 1, 2009

By A. Sheikh, S. Hardcastle

"Various methods of leaching are being used by Denison Mines Ltd. Uranium Operations. This study was designed to investigate the flood leaching operation of two parallel inter-connected stopes contained by pressure bulkheads. The teaching muck piles, created from large scale uppers production blasts, are aerated by compressed air lines laid beneath the pile prior to blasting.A SFr, tracer gas, injection technique has been employed to determine the post-blast integrity of the single-ended air distribution system. SF6 was injected into the compressed air line feed to the stopes and collected at borehole exhausts from the stopes in grab-sampling bags. Analyses of the air samples were performed with a gas chromatograph.The system was designed to give a sufficiency of oxygen to sustain bacterial activities used to enhance the leaching recovery in the muck piles. The results obtained indicated that there is a minor anomaly in the distribution system that may not be critical to the operation. Compared to an idealized case, the over-all efficiency of aeration throughout the muck is estimated at over 85%."

Jan 1, 1988

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By Terry Braden

"Meeting probable world mineral demand in the years ahead will almost certainly require an ability to economically treat lower grade and more complex ores. Achieving this will require extensive research and technical development across the full spectrum of mineral processing.For mid-sized or smaller companies the most effective way to participate in such extensive programs - and gain access to the technology required to stay competitive - may be through collaborative research.This paper explores the recent history of collaborative research in mineral processing and in particular its ability to attract world-class multi-institutional research teams with sufficient resources to make step-change advances. It chronicles the advances achieved, but also explores the research architecture and administrative structures required to deliver research outcomes and technology transfer mechanisms to a range of often disparate sponsoring companies.INTRODUCTIONIn medieval times the dream of alchemists was to turn base metals into gold. We modern alchemists, of course, don’t waste our time on that sort of foolishness: we turn base metals into dollars. When I see the profit reports filed by some companies recently, I can only conclude that a lot of those present today must be pretty good at this.But the fact that we are here at this conference reminds us that an alchemist’s work is never done; turning base metals into dollars is not a one-trick wonder but an art that we must extensively refine year after year if we are to survive in a competitive marketplace.It is not that demand for metals is likely to slow; most people seem to think that China, India, Brazil and other emerging economies are still at the lower end of their demand curve. They will need significantly larger volumes of metals in the years ahead. The challenge for us as processors is that to supply increasing tonnages of those metals profitably we will almost certainly need to process more complex or lower grade ores and probably to do so with reduced energy inputs."

Jan 1, 2009

By S. Ivanova

The results presented in this paper show that the gold solution dilution is a key parameter to control the dispersion of gold on ?-Al2O3 the selected support. The variation of concentration leads to changes in pH which modify the nature of gold complexes from HAuCl4 formed in the solution. These complexes are presented. Some of them (AuCl3(OH)- and AuCl2(OH)2 -) react with the surface of alumina and give interesting interaction. AuCl2(OH)2 complex has been considered as an ideal complex because of the strong anchorage of a bidentate species on the alumina. This complex is formed mainly in a solution of gold with a concentration of 10-4 M giving a pH of 3.5-4.5. The nature of the anchorage and the amount of chlorine, has an influence upon the formation of Au-Cl bridges which modify the dispersion of the gold on alumina of the final catalyst as shown by TEM.

Oct 1, 2003

By L. Bryson, J. H. W. M. Brits, K. Voogt

"The Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) has the world’s first full deposit nickel plating tankhouse. Impurities in the nickel electrolyte can induce stresses in the electrowon nickel deposits that could lead to delamination of the deposit. Identifying the impurities that contribute to increasing internal stresses in the nickel deposit is key to successful operation and automation of the tankhouse. Impurities were introduced in the plant electrolyte and the effects on the full-scale nickel deposits evaluated. The impurity-adjusted electrolyte solutions were also analyzed using commercially available bench-scale methods to determine the induced stress. A correlation between impurity-induced deposit stress and full-scale delamination was developed. A direct correlation can now be made between feed quality, i.e. impurity concentrations, and degree of delamination in the plant. This methodology has the potential to rapidly predict the effect of new reagents, upstream process upset conditions and synergistic interactions between impurities on deposit stress and delamination of nickel deposits.INTRODUCTION Nickel electrowinning in sulphate media was first pioneered by Outokumpu in its Harjavalta refinery in 1960 (Saarinen and Seilo, 1985). The original process was very manual with starter sheets plated onto “acid resistant” steel for 36 hours and then manually stripped and cut into sheets which could be inserted into the main production cells for a further 4–5 days. The starter sheet stripping and manufacture process was later automated. The same technology was subsequently implemented on a number of plants around the world. Anglo American Platinum’s Base Metal Refinery (BMR) began nickel electrowinning in the early 1980’s. The recent expansion of Anglo American Platinum’s Base Metals Refinery necessitated the construction of a new nickel tankhouse to achieve two primary objectives. The first to increase the capacity to 32 400 tpa nickel and the second to reduce employee occupational exposure to nickel aerosols. The new tankhouse has been commissioned and is in the process of ramp-up; more details are given by Hagemann et al. (2016). Fundamental to lowering employee exposure to aerosols was automating both harvesting and final handling of cathode. In order to accomplish this a bold move was taken to plate up to 10 days on permanent titanium blanks which are harvested by automatic crane and automatically stripped. The original development work for the plating nickel on titanium blanks over a ten day cycle is given by Bryson et al. (2006)."

Jan 1, 2017

By C. Veloo

"Westmin Resources operates a mine/mill complex at Myra Falls and produces copper and zinc concentrates with minor associations of gold, silver, and lead from a polymetallic, massive sulphide orebody. Mill flotation performance has historically been plagued by periods of uncontrollably high circulating loads leading to low concentrate grades and below optimal tails. This led to a detailed examination of the flotation process. Locked cycle, and pilot plant data are presented. In addition, plant design and commissioning as well as column cell details are discussed. A comparison between actual and predicted performance is also presented. Benefits realized are higher copper and zinc concentrate grades and improved zinc recovery.PrologueMyra Falls Operations is located at the south end of Suttle Lake in Strathcona Provincial Park. Access to the mine site is provided by a 90km paved highway from Campbell River, British Columbia.The mine and facilities are nestled in the narrow Myra Valley between Mount Phillips and Mount Myra. These steep, rugged mountains rise from the valley floor at an elevation of 900 feet to summits of almost 6000 feet. The steep slopes are heavily wooded with fir, hemlock, and cedar up to an elevation of 4000 feet where a transition to alpine meadows occurs. The summits are craggy rock faces, some capped with glacial ice. Myra Creek winds its way through the valley dropping several hundred feet into Suttle Lake. Precipitation is high at over 100 inches per year, which may include up to 10 feet of snow in winter. The temperature may range from 32° C in summer to -18° C in winter.Myra Falls began production in 1965 with the Lynx Mine, supplemented by the Myra and Price Mines in subsequent years, feeding a 950 stpd mill up until the middle of 1985 when the H-W mine was brought into production. The original mill was replaced with a modern 2700 mtpd facility and in 1988 production was increased to 4000 mtpd.Both Lynx and H-W mines are currently in production producing an average of 3650 mtpd. The ore minerals are primarily sphalerite and chalcopyrite, with subordinate galena, bornite, tetrahedrite, and electrum."

Jan 1, 1992

By D. A. Trotter

"This paper traces the main advances in mine lighting from neolithic times to the 1960s. The earliest lights consisted of reeds or strips of wood soaked in grease. As man's knowledge increased, the oil lamp, the candle, kerosene, acetylene and finally electricity have allowed him to see where no natural light could penetrate. These advances in technology, however, did not come easily. Many false starts were made and great dedication was required by a few lighting pioneers to overcome the many technical difficulties that were encountered. The lighting of coal mines in particular caused unique problems, as there was the ever-present threat of methane explosions. Advances in mine lighting will continue, but these advances are only possible because men like Davy, Wolf, Marsuat and Edison paved the way.IntroductionMan's first efforts at mining consisted of merely picking rock off the surface of the earth. The sun was his only source of light. The early mines of the Neolithic age were simply vertical pits, 5 to 8 m deep. In order to follow an orebody, miners began to dig horizontally from the bottom of these pits, and as work progressed the need for additional light became apparent. With the discovery of the light-giving properties of fire, man was no longer dependent on natural light. Figure 1 gives an impression of the earliest artificial mine lighting used.Early Evidence of Mine LightingCarbonized residue from wood chips which had been inserted into rock cracks can be found in early Neolithic workings. The mines at Krzemionki Opatowski in Poland contain very narrow low tunnels that were lit in this fashion and were worked from 2300 to 1800 B. C. The wood had to burn downward to provide light and because wood burns poorly in this position, the chips were probably soaked in animal fat to make them burn more easily."

Jan 1, 1982

By R. S. Nichols

"During 1973 to 1978, Canadaka Mines Limited, a subsidiary of St. Joseph Explorations Ltd., undertook an extensive exploration and development program in the Cobalt area. This program resulted in the delineation of previously unknown stratigraphic units in the Archean volcanic sequence. During this time period, significant are controls related to area silver deposits were also identified.The Archean geology is comprised of a volcanic pile conformably overlain by sediments. The volcanics contain at least two felsic volcanic centres near the stratigraphic top of the pile. The bulk of the pile consists of mafic flows and interflow sediments. lnterflow sediments around silver are shoots contain mineralized halos of base metal sulphides. The halos exhibit lateral and vertical metal zoning with Cu, Pb and Zn mineralization decreasing away from an are shoot.Silver mineralization controls determined during the Canadaka program agree with the historically well established importance of Coleman sediments as well as Archean contacts for hosting silver deposits. The vertical extent of are shoots is typically 150to 250ft. A strong correlation was found to exist in the Cobalt area between Archean strike and the strike of are veins. Finally, al/ Cobalt area are deposits appear to be associated with a distinct volcanic pile at the top of a sequence of Archean flows."

Jan 1, 1988

By Ron Ferris

The Westinghouse Temptifier TM, using heat pump principles, recovers lowgrade waste heat in the 600P to 1600P temperature range and amplifies it to usable levels of up to 2200P. Coefficients of performance (C.P.D.) normally encountered are from 3.0 to 6.0, with capacities from 200,000 to 10 million Btu/hr.

Jan 1, 1979