Search Documents

By Adil Aledresse, N. Emre Altun, Bern Klein, Nuri Hmidi, Brent Hilscher

A study was conducted to investigate high gold grades in water lines and carbon fines collected from the Musselwhite gold recovery circuit. It was discovered that fine magnetic particles in the overflow from the carbon fines settling tank launder had high gold grades ranging from 2,000 to7,000 g/t. The -37 micron fraction had up to 17,000 g/t gold. Scanning electron microscopy revealed the gold was attached to the surface of iron particles. The objective of the study was to identify possible mechanisms that result in the attachment of the gold to the magnetic iron particle surface and to recommend process modifications that would reduce these types of gold losses around the carbon circuits. Solid and solution samples were collected from the gold recovery circuit and analysed. Two possible mechanisms were identified including gold cementation onto iron and heterocoagulation of colloidal gold onto iron oxides in the elution column. Possible sources of the colloidal gold include reduction of gold cyanide complex to metallic gold in the carbon regeneration kiln and gold detached from cathode in EW cell. Based on SEM+EDX, the sources of iron were natural magnetite and roasted iron sulphides. Thermal reduction of gold is believed to be the cause of dendritic gold from the carbon regeneration kiln.

Jan 1, 2014

By Margarete Kalin

"Biotechnological approaches to decommissioning of mine waste management areas are presented in the context of sustainable environmental management. Improved design of waste sites and environmental management paves the way for the application of new technological approaches. Mining wastes are better confined, effluent quantity is reduced and the quality is expected to improve in the future. The biologically mediated treatments focus on the creation of conditions inside the waste management area which lead to the confinement of the contaminants in the inactive tailings ponds and seepage collection ponds, as well as pits or other disturbed areas which were part of the operating conditions.Biogeochemical reactions lead to three fundamental water treatment steps mediated biogeochemically , alterations in chemistry which lead to formation of particles, which then have to flocculate and be assisted to collect in the bottom of the ponds. Microbially active sediments are installed to assist particulate formation and serve as sinks for metals. In deeper sediment strata, stable forms of metals are created. Biological polishing is used to collect the particulates and relegate them to the sediment. Examples will be given of the application of these processes, to waste rock piles, open pits and tailings ponds. This paper attempts to show that, through the integration of applied biotechnological advances and the application of new approaches to decommissioning, reductions of environmental impacts by mining are possible. * Note: this paper has been presented at the 13th Annual Meeting of BIOMINETIntroductionThe role of biotechnology in decommissioning of mining waste management areas should be placed in the context of sustainable development. The concept of sustainable development as defined by the Brundtland Commission (1987) for the restoration/ reclamation of mining operations could be translated as follows: The increasing demand for the resources by the world population must be met in a manner which does not compromise the earth's environment over the long term (Brooks et al., 1995)."

Jan 1, 1998

By F. Liu, H. A. Meier, D. M. Valiveti, P. A. Gordon

Hydraulic fracture is a frequently used technique in the Oil and Gas industry to create high permeability pathways for extraction of hydrocarbons. Numerical simulation of this method poses challenges such as representation of 3D fractures, propagation of randomly oriented fractures in 3D media, enabling fluid leak-off from fracture to poro-elastic medium. We have developed a numerical model using the Generalized Finite Element Method (GFEM) to simulate fluid driven fracture in a poro-elastic medium that addresses these challenges. In the GFEM framework, special enrichment functions are used to augment the solution space in the displacement and pore-pressure fields in order to accurately capture the response in the vicinity of the fracture. Adaptive refinement of the finite element mesh is also employed to facilitate accurate and efficient solution of the model. Our model fully couples fluid flow in the fracture, represented with the lubrication approximation, to the geo-mechanical behavior of the bulk poroelastic rock, comprised of an elastic rock skeleton saturated with fluid. Fracturing fluid exerts traction on the fracture surface and is also allowed to leak-off into the poroelastic medium using a transfer function approach. Stress intensity factors (SIFs) are evaluated based on the Contour Integral Method, accounting for the fluid pressure on the fracture surface. The SIFs are used to govern a full 3-D evolution of the fracture. Verification of the model is performed for known behaviors for the poroelastic response and fluid flow in the fracture.

Jan 1, 2015

By G. E. Agar

This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady-state balance can be calculated for a circuit. Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative technique to arrive at the steady-state balance. The program is written so that a variety of circuits can readily be simulated. A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets are presented on sulphide ores, on copper-nickel separation and on silver flotation.

Jan 1, 1978

By P. Mageau-Béland, È. -M. Proulx, M. -C. Patoine

Over the past six decades, Hatch has helped several industrial processing facilities in debottlenecking their operations, allowing them to produce more with the same equipment, to reduce and even eliminate expenditure investments, or to increase the return value of their expansion projects. These successes result from the application of a proven analysis approach that can be applied to any industrial facility. A five-stage methodology is discussed and demonstrated with a specific example of a nickel concentrator optimization study. The first stage is an observation stage which allows to meet key actors at the plant, develop mutual understanding of problems, understand operating philosophy, and efficiently collect large amounts of operating and maintenance data. Following is a data compilation stage during which data is analyzed over a representative time period to identify parameters that significantly affect the production, to evaluate data reliability and to define the focus of the upcoming analysis. Quantitative metrics are defined using statistical tools such as pivot tables, histograms, percentiles and MDR (Maximum demonstrated production rate during 3 to 7 consecutive days). Then, the production bottlenecks are identified by a thorough analysis of the facility’s control philosophy, process throughput, equipment capacity, availability, downtime causes, and interaction between components of each circuit. Understanding the maintenance practices and frequency of planned shutdown is also critical to this analysis. Opportunities for improvement are identified in collaboration with the operation, maintenance and engineering teams, ranked as a function of their impact on the bottlenecks and prioritized. The final and most critical stage involves engagement with the plant stakeholders, namely the operators and the maintenance staff members, to present the results of the analysis and obtain their participation in the implementation of the solutions. The benefits of the case study translated into: 10% production capacity gain, improved maintenance planning and avoidance of several million dollars of investment.

Jan 1, 2016

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By Paulo F. T. Sachs

ERP systems have been widely implemented nowadays in several industries. However, ERP was originally designed to fit former MRP and MRP II users, and most of the ERP research has been focused on discrete manufacturing . On the other hand, process industries ? and mining in particular ? present many peculiar characteristics, which are difficult to comply with ERP systems standard functionalities. Again, very limited research has been developed covering enterprise management systems in mining. The objective of this paper is to identify, through an explanatory study that includes a case study methodology, how ERP systems manage the functional areas of the mining industry, and how they fit into the mineral value chain IT requirements. A secondary objective is to identify the gaps between ERP?s functional capabilities and the mining industry business requirements, and to point out the perceived benefits they generate to the companies.

May 1, 2004

By M. Stogran-Baker, E. Legault-Seguin

"Fluorspar mining in the St. Lawrence area of Newfoundland and Labrador began in the 1930s and ended in the mid-1980s. In 2013, Canada Fluorspar (NL) Inc (CFI) discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods and began developing this resource. This paper discusses the flowsheet development of the AGS vein deposit. Testing at SGS began in 2009 with samples from other deposits in the area. The testwork included pilot-scale dense medium separation (DMS), laboratory-scale flotation tests to develop the flowsheet and a flotation pilot plant. The more recent work that is presented here has been devoted to the AGS vein, and included a variability testing program that gave tremendous insight into the metallurgical drivers of processing the deposit. The ore was found to be fairly variable in terms of fluorite grade, but also gangue mineralogy, which had greater implications on the DMS performance. The gangue mineralogy was also found to significantly impact the grindability characteristics of the DMS product. This paper will detail the testing conducted and the mitigating steps which were identified for the operation.INTRODUCTION Fluorspar is the industrial trade name for the mineral fluorite (CaF2), which is the primary industrial source of fluoride. There are a number of categories of fluorspar, most notably acid-grade fluorspar and metallurgical fluorspar (metspar). Acid-grade fluorspar has stringent specifications and is suitable for the production of hydrofluoric acid that is used for many applications. The typical specifications of acid-grade fluorspar are >97% CaF2 and less than 1% each of SiO2 and CaCO3, with a particle size distribution in the order of 80% passing 100 µm. Metspar is typically used for metallurgical purposes, typically as a flux in smelting, and has significantly more relaxed specifications (< 15% SiO2). The principle source of fluorspar in Canada has been from the Burin Peninsula in Newfoundland and Labrador. More than 3 million tonnes of fluorspar were produced there between 1940 and 1978 and from 1987 to 1990, when production ceased (Fulton & Montgomery, 1994)."

Jan 1, 2018

By J. B. Scott

"A computerized cost estimating program developed with the use of the Lotus 1-2-3 spreadsheet program has produced dramatic savings in preparing estimates for operating costs, equipment fleet size and manpower requirements for underground mines.The program is used by Dynatec to support its consulting engineering projects, particularly feasibility studies. The &apos;first principles&apos; approach is used to prepare detailed estimates under direct labour and supplies categories and maintenance costs for each mining operation . User notes have been developed to guide the estimator and ensure appropriate consideration is given to the specifics of the particular mine.A typical case history is illustrated and the ease by which alternatives and sensitivity analyses can be prepared is demonstrated. IntroductionHistorical MethodsMining engineers have used one or a combination of methods to prepare operating cost estimates for new or existing mine s. Operating companies have access to historical cost data and generally use this for preparing estimates. Consulting engineers do not usually have direct access to such information and must rely on mining companies (the present or previous clients); publications (text books, equipment manufacturers manuals, CMJ reference manual, etc.); annual reports (applicable to public companies); previous studies (to be used with caution as conditions change from mine to mine); and first principles (the subject of this paper), for cost information:Definition of First PrinciplesA first principles approach to cost estimating considers individual primary work elements of an operation. Quantities of work items are developed from the mine plans, production rates, geographic and physical layouts etc. The knowledgeable estimator, assisted by experienced operations personnel, can assign appropriate resources (equipment, labour, supplies and services) to each work element and establish productivities. Completion of the cost estimate is then largely arithmetic."

Jan 1, 1988

By B. Morrison

"The Kiruna Electric System is a recently developed inclined ore haul age system for underground mining operations. Although an initial investigation was carried out at the Swedish underground iron ore mine LKAB almost three decades ago, it was not until 1981 that the resources of LKAB, ASEA and Kiruna Truck AB were combined to investigate, and subsequently develop an ""all- electric truck"" for the mining industry.It has long been appreciated, that major economical advantages could be realized by a mining operation through an extension of the cost-effective life of the existing ore hoisting system by the use of ramps to haul ore up to the main haulage level. Diesel truck s have been used and are being used for ramp haulage. Their use however, is limited due to ventilation and operating costs restraints.There are numerous instances of orebodies, located within a couple of hundred metre s of surface, or below an existing hoisting facility, being developed by ramp access while the shaft is being sunk. Development of an orebody via ramp access has many advantages to a mining operation where mechanized mining is to be practiced. These advantages are both practical and economical; generally falling within the over-all umbrella of the phrase ""cash flow"" mining.The decision to sink a shaft is a major committment by any mining company, regardless of size and financial reserves. Extensive diamond drilling, both shallow and deep must be carried out before a decision can be executed. This constitutes a major financial expenditure over an extended period of time.The decision to sink a shaft must be weighed against the reliability of geological interpretation of the deep diamond drilling results, the stability of the mineral market and potential fluctuation in ore prices and interest rates."

Jan 1, 1989

By Piotr Malkowski

Studies on the properties of rocks heated to high temperatures are rather rare. Such research is occasionally conducted for example; in areas around nuclear power plants. The national Polish coal gasification (underground coal gasification, or UCG) project has, however, forced the analysis of the geomechanical properties of heated rocks in the vicinity of a designed geo-reactor. Ukrainian experience with UCG show that rocks up to 2 m from the burned coal seam be at a temperature > 600ºC. Such a high temperature will undoubtedly influence their physical properties. This paper presents studies on the strength and deformation properties of carboniferous rocks in the Upper Silesian region, where the UCG process is planned. Three types of rocks were tested: claystones, mudstones and sandstones. Laboratory tests of these rocks evaluated compressive strength, elastic modulus and weight loss. An evaluation of the results of the tests comparing the thermal conductivity of rocks and their specific thermal capacity was then carried out. All of the rocks studied were heated to 300, 600 and 1000ºC, and also evaluated at room temperature. This procedure shed new light upon the behavior of heated rocks in relation to their distance from the designed geo-reactor. The test results presented were developed within Research Task No. 3 ?Developing a technology of coal gasification for efficient production of fuels and electric power?, financed by The National Centre for Research and Development under strategic research and development programme ?Advanced Technologies for Energy Generation.?

Aug 1, 2013

By S. E. El-Alfy, John Starkey

"The Iron Ore Company of Canada treats up to 125,000 t/d of iron ore at its Carol Concentrator in Labrador City, NF.A complete water balance study in the concentrator was done to show how to reduce the consumption of fresh water, to improve metallurgy in the magnetic separation (mag) plant, and to help reduce maintenance costs for the reclaim water and tailing pumping systems.The study showed that more than 60% of the water used in the mill was internally recycled dirty water from dewatering cyclone overflows, and that water reduction was closely tied to the effective use of these internal reclaim pumping systems. In addition, new operating parameters were set for the 4 -15,000 USGPM reclaim water pumps which should save over $100,000 per year in maintenance costs.IntroductionThe study described in this paper was set up for the purpose of lowering water usage in the concentrator, and to reduce tailing and process water pumping costs (operating and maintenance). Another benefit was also expected, namely, to improve magnetic separation efficiency through better water and density management of magnetic separator feed streams.The procedures selected to perform this work were: ( 1) to prepare accurate, as built flowsheets of the entire iron recovery process, including fresh and process water systems, (2) to calculate normal material balances in all circuits at full production, (3) to use the computer spreadsheet model so generated, to evaluate specific ways to reduce water consumption and (4) to re-evaluate metallurgical performance and operating parameters in the light of this information.Overall control of the 28 spiral iron recovery lines was found to be excellent because automated start up and shut down of the individual lines had been incorporated in the design from the start. Because production rates can vary due to sales requirements, mine and mill maintenance delays and hardness variance, the mag plant (which treats spiral tailings) must deal with a wide variety of operating conditions. Good water management therefore is a key item in achieving high recovery of the fine free magnetite which is too fine for recovery in the spirals.In order to make the study as accurate as possible, process data for major flows was reviewed by metallurgical staff and then by mill supervisors. The operating picture of the concentrator so generated was judged to be a good estimate of the mill at full production. By changing key inputs, the variance of process water demand and tailing slurry produced for several other operating conditions were studied.The usefulness of this exercise has prompted this present presentation to be made. Older plants by nature have undergone many revisions as operators have worked through ore changes, market changes, labour cost increases and the availability of new equipment, to improve their operation. Sometimes therefore it is necessary to stop and reassess what is happening in a plant in order to continue the never ending work of process optimization. The techniques used here were ideally suited to the gravity/magnetic concentration flowsheets used, but there is no reason why similar studies could not be done in other process plants.The authors of this paper hope that this experience at IOC will be helpful to others who face similar challenges in the pursuit of excellence in their processing plants."

Jan 1, 1995

By Glenn Norris, Tyler Buckingham

"Gold recovery gains in the order of one to two percent have been realized in 2009 due to changes in the operation of the grinding circuits at Barrick Gold Corporation’s Hemlo - Williams Mill. The initiative known as “split milling” involves milling low grade open pit ore in one grinding circuit and higher grade underground ore in the other grinding circuit under different conditions.The philosophy of split milling involves processing higher grade underground ore at a lower throughput rate and a finer grind while milling lower grade open pit ore at a higher throughput rate and a coarser grind. Bench scale tests showed that the recovery relationship for underground ore sources was much more grind sensitive than that of open pit ore. This relationship proved to hold in the plant. The gold recovery gain due to finer grinding of the higher grade ore is much greater than the recovery loss due to coarser grinding on the lower grade ore. Since the majority of gold is being recovered at a higher rate, this results in higher overall plant gold recovery when compared to the traditional operation philosophy of blending the ore sources.The challenges for achieving the maximum benefits of split milling were two fold; the need to increase throughput on the open pit ore milling circuit and a means of grinding finer on the underground circuit. The former was met with an increase in SAG (Semi-Autogenous Grinding) mill ball charge, a basic “drill to mill” blasting campaign and changes to the primary gyratory crusher. The latter was met with a reduced SAG mill ball charge and a higher milling density. The resulting benefits in additional gold recovered are in the order of $3-5 million per annum.INTRODUCTIONThe Williams Mill processes ore from three different ore sources, the David Bell Mine (DB), the Williams Underground Mine (WUG) and the Williams Open Pit (OP). All three ore sources are located within the Hemlo camp in Northwestern Ontario adjacent to the Trans-Canada Highway. The Williams Mill was built in the mid 1980’s at which time it was designed to process 3,000 dry metric tonnes per day through a 22’ SAG mill in series with a 16’ ball mill. In 1988 a Mill expansion doubled the mill capacity by adding a second identical grinding circuit. A photo of the current grinding circuit can be seen in Figure 1. Today the Williams Mill processes an average of 8,000 tonnes per day of which approximately 60% is from the Williams Open Pit."

Jan 1, 2010

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By H. J. Chalmers

"Since the advent of large volume flotation machines, Cominco Ltd. has actively studied possible application of such machines to their various milling operations. A number of installations have been made and more are on the drawing board. This paper gives a description of these units, information as to choice of equipment, and information as to operating experience. Mechanical and operating details of six installations are summarized. Three different types of machines are discussed.Pine PointThe original Pine Point zinc flotation circuit comprised conventional roughing with two stages of cleaning. Over the years with increase in feed tonnage there have developed two adverse conditions; namely, a reduction in zinc concentrate grade coupled with an increase in MgO in the concentrate. This resulted in higher freight payments along with more severe smelter penalties. An intensive test program, in 1971, showed that the concentrate grade could be raised by 1.5 units of zinc along with a reduction in MgO from 0.8% to 0.47.. Subsequently this was done by adding two additional stages of cleaning using 16 cells of Denver 200-V's. The project was completed in January 1973 at a cost of $510,000 to give an estimated annual savings of about $390,000.Selection of the Denver Model 200-V was based on minimum floor space requirement, availability, and favourable operational and maintenance experience with Denver 100’s. As it happens it was possible to ""shoe-horn"" the 16 cells into place with a minimum of plant alteration. Some problems have been encountered with a tendency to ""sand up"" at high pH, particularly at the corners. Otherwise operational service has been very good."

Jan 1, 1974

By A. L. Irwin

THE disposal of tailing or waste material, which is generally a very large proportion of the ore treated, is a major problem in the location and operation of any concentrating enterprise and especially so where the life of the operation is expected to continue for many years. Many factors need to be taken into consideration in the selection of a tailing site, chief among which are economical handling of the material, subsequent re-treatment of the tailing, and precaution against stream pollution by waste water. The final location of many mill sites bas been governed largely by the selection of a sui table area for tailing storage. The Sullivan concentrator of the Consolidated Mining and Smelting Company is situated about three miles from the Sullivan mine at Kimberley, B.C., and one of the deciding factors in its location at this distance from the mine was the availability of a suitable area in which tailing could be deposited. In view of the indicated long life of the property, a far-sighted policy bad to be adopted in the matter of tailing storage, for not only would it be necessary to accumulate a huge tonnage of finely ground material, but also reclamation for iron recovery at some future date bad to be considered. Some idea of the extent of the problem may be grasped when it is noted that, by the end of 1938, over 18,000,000 tons of tailing bad been impounded in an area of some 200 acres.

Jan 1, 1939

By M. J. Baker

Energy and Minerals Australia Ltd are undertaking a study of the recovery of uranium from the Mulga Rock Deposits in Western Australia. Approximately 80-90% of uranium identified to date is present as tabular layer up to 5 m thick within a lignite seam 30 m to 50 m below surface. Other metals are also present. Metallurgical studies at ANSTO Minerals laboratories in Sydney have focused on identifying a suitable uranium leaching process and assessing the possible downstream impacts of the organic material in the ore. The extraction of other metals has also been examined. This paper provides the results of testwork performed at ANSTO to date.

Aug 1, 2010

By Pura Alfonso, Teresa Escobet, Hernan Anticoi, Eduard Guasch, Josep Oliva, Sarbast A. Hamid

"The liberation modelling of mineral particles using mineral liberation analysis have been used in the past to model comminution and concentration processes. In this work this concept has been taken a little further, using comminution and concentration for applying the mineralogical characteristics of particles. This approach is shown using the image analysis, mineral liberation analysis and the distribution density functions for liberation modelling. The work focused on the effect of comminution on mineral liberation for liberation modelling. To model this, effect the mineral liberation of the particles using distribution density and the cumulative distribution was linked to the image analysis of the ore particles. These properties have been estimated by statistical measures such as the distribution density and liberation grade, which were extracted from MLA data and images analysis, using proper image analysis and techniques based on MATLAB software. A comparison of different tungsten ores of liberated particles, has been introduced and evaluated by estimated results and image analysis.INTRODUCTION The chief economic minerals of tungsten are wolframite [(Fe,Mn) WO4] and scheelite(CaWO4), and approximately two-thirds of the world tungsten reserves consist of scheelite deposits (Lassner and Schubert, 1999). Tungsten has unique properties and is widely used in various industrial high strength and high temperature applications. It occurs coarsely aggregated in low grade ores. Most of tungsten ores, particularly scheelite, wolframite and ferberite, occur in deposits with very low content of WO3 (0.1–2.5%) that is not economically viable to apply directly metallurgical methods to extract tungsten (Martins, 2014). Tungsten is considered as a critical metal by the European Union by the economic importance and also the high supply risk (European Commission, 2014; Chakhmouradian et al., 2015).Currently, scheelite is playing an increasingly important role in tungsten industry because the mineral reserve of wolframite is getting depleted after gradual exploitation and utilization (Min et al., 2016). In mineral processing, the liberation of valuable mineral from the gangue determines the efficiency of subsequent separation processes. The liberation characteristics of an ore are primarily dependent on its texture, the association of mineral in the host matrix of gangue minerals, and to some extent on the grinding process (Zhang and Subasinghe; 2013)."

Jan 1, 2017

By H. Nakano

The codeposition behavior of impurities such as Ag, Bi, Fe, Ni, Pb and Sb with Cu was investigated galvanostatically at 5-3000 A/m2 using a Pt cathode at 60 °C in acidic copper (I) chloride (cuprous chloride) solution at pH1-2 containing 1.0 mol/L of Cu+ and 4.9 mol/L of Cl-. The impurities were classified into two groups: Group I (Ag, Bi) which codeposits with Cu as a metal, and Group II (Fe, Ni, Pb, Sb) which is slightly involved in the deposited Cu in nonmetal form from the electrolyte. Silver and Bi in Group I behaved as more noble metals than Cu, and significantly codeposited with Cu, showing typical features of regular-type codeposition. When Cu was deposited dendritically, the Ag and Bi content in the deposit increased with increased duration of electrolysis as a result of decreased net current density caused by increased cathode area. The current efficiency for Cu deposition in impurity-free solution was 95-100% over 100-1000 A/m2, but it abruptly decreased at above 1000 A/m2 when the limiting current density of Cu was attained. Although Fe, Ni, Pb and Sb in Group II were involved to 0.01-0.02 mass% in the deposit, they had no influence on the current efficiency or morphology of Cu.

Jan 1, 2007

By M. Sturzenegger

This paper documents a field survey using long-range terrestrial digital photogrammetry at the Palabora open-pit mine, South Africa, for multi-scale characterization of rock mass discontinuities. Stereomodels covering the entire mine were generated based on photographs taken from a distance of 1600m across the pit, using a series of f=20-400mm lenses. Details on the methodology used and its accuracy are discussed. Preliminary results on discontinuity orientation, persistence and intensity are presented, highlighting the effect of observation scale. The potential uses of long-range terrestrial digital photogrammetry in open-pit mine and large natural rock slope environments is emphasized. The use of an f=400mm lens from distances larger than 1.5km may represent an important step forward in the geotechnical characterization of inaccessible remote rock faces.

May 1, 2009