Search Documents

By M. Kalin

"Ecological Engineering, a biotechnological approach to the decommissioning of base metal mining wastes, is being tested on two pits (Gloryholes) in Newfoundland, Canada. Pit #2 has an average pH of 3.5 and flows into Pit #1 where, through additional ground water contribution, the pH is circumneutral, ranging between 5.5 to 7.The AMD in Pit #2 originates from underground workings and exposed massive sulphide on the pit walls. The overflow from Pit #1 averages about 10 L/s with less than 0.2 mg/L of Cu and 40 mg/L of Zn.Ecological Engineering utilizes organic substrate as a source of carbon and nutrients for microbial populations which can generate alkalinity and reduce metals. In 1989, limnocorrals (enclosures of 4 m diameter and approx 3 m depth) were placed in both pits to test the most suitable organic amendment (peat and sawdust). Microbial alkalinitygeneration was evident 95 days after placement of the amendment on July 4, 1989. The pH had increased after 120 days from 3.5 to 4.5 and by day 480 the pH was 7 in limnocorrals in Pit #2. Zinc concentrations in the limnocorrals in Pit #2, dropped from an average of 35 mg/L to about 2 mg/L or less, by day 480.A scaled-up experiment has been under way since August 25, 1990, where 390 m3 are treated in pit #2 and 750 m3 in Pit #1. One hundred eighty days after placement of the amendment, zinc was reduced in the acid Pit #2 from 40 mg/L to 15 mg/L. Research is underway to determine those factors which limit microbial activity."

Jan 1, 1992

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By G. T. Fisher

A continuous process is used at Phelps Dodge Sierrita Inc. to produce copper sulfate pentahydrate via a solution extraction ? crystallization approach to supply the animal feed market. A review of the fundamental concepts of the process and unit operations is presented. Improvements in the process are aimed at achieving a controlled size distribution of product crystals (-40+80 mesh) with minimization of fines by primary nucleation and crystal breakage. An independent temperature control design was implemented for the heat transfer medium (water) in each crystallizer, albeit using common headers in and out of the chiller. This design was developed to maintain a controlled degree of supersaturation in each vessel while preventing localized spontaneous nucleation of fines and reducing encrustation of the heat transfer surfaces in each crystallizer. A model was developed to calculate the heat load and heat transfer coefficient of each crystallizer along with the saturation copper tenor as a function of temperature and free acid.

Jan 1, 2007

By B. Garitte, O. K. Mahabadi, P. Marschall, A. Lisjak, H. R. Müller, T. Vietor, G. Grasselli

Numerous research studies have shown that clay rock formations exhibit favourable characteristics for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this paper is to present new rock mechanics insights into the phenomena involved in the EDZ formation and evolution processes in Opalinus Clay, a clay shale currently being assessed as a potential host rock for an underground repository in Northern Switzerland. More specifically, discontinuum-based computer simulations, using a hybrid finite-discrete element method (FDEM) approach, were applied to two case studies considering circular excavations in an anisotropic Opalinus Clay formation. In the first case study, numerical modelling was applied to the HG-A experiment, a long-term in-situ test carried out at the Mont Terri underground rock laboratory to investigate the hydro-mechanical response of a backfilled and sealed microtunnel. A mechanistic analysis of the fracturing processes involved in the EDZ formation was carried out. In the second case study, the long-term effect of the bentonite backfill swelling on the EDZ around an emplacement was numerically analyzed. Overall, the simulation results highlight short-term distinctive rock failure kinematics due to the bedded rock structure, as well as a long-term reduction of the excavation-induced fracture porosity in response to mechanical loading.

Jan 1, 2015

By Richard Dahl, Richard P. Taylor, David H. Watkinson

"Abstract - Detailed mapping of the Eastern Gabbro, Coldwell Complex, Ontario, revealed that the copper and platinum-group-element deposit on the Marathon property is confined to a coarsegrained to pegmatitic gabbro-diorite intrusion, the Two Duck Lake intrusion (TDLI). Exposed along the eastern boundary of the Coldwell Complex, the TDLI was emplaced as a sill whose orientation is slightly oblique to the general structure of the Eastern Gabbro. The TDLI has been subdivided into lower, middle and upper sub-units on the bases of lithological, textural, mineralogical, and geochemical criteria. Both border sub-units are sulfide-, base- and precious metal-enriched, and exhibit abundant evidence of host-rock assimilation. The primary mineral assemblage in the TDLI is plagioclase, olivine, clinopyroxene, Fe-Ti oxides, with accessory orthopyroxene, biotite, apatite; this primary mineral assemblage is essentially preserved in the core of the intrusion (i.e., the middle subunit). The Cu-PGE Marathon deposit, delineated mainly in the upper sub-unit of the intrusion, consists of disseminated Fe-Cu-Ni sulfides, and platinum-group-minerals derived by hydrothermal remobilization from primary magmatic sulfides. Enrichment in Cu and PGE resulted from partial replacement of original Fe-Ti oxides and pyrrhotite in the primary mineral assemblage by reaction with (a) residual magmatic fluid, and (b) fluids derived from the breakdown of host rock xenoliths and hydrothermal alteration along the lower contact of the TDLI. Résumé - La cartographie détaillée de l’Eastern Gabbro, Complexe Coldwell, en Ontario, révèle que le gisement de cuivre et éléments du groupe du platine de Marathon est confiné à une intrusion gabbro-dioritique, de grain grossier à pegmatitique, l’intrusion Two Duck Lake (TDLI). Cette intrusion s’est mise en place sous la forme d’un filon-couche légèrement discordant sur la structure de la bordure orientale de l’Eastern Gabbro. On y distingue trois sous-unités, inférieure, centrale et supérieure, sur la base de zonations lithologique, minéralogique et géochimique. Les sous-unités marginales sont enrichies en sulfures, métaux usuels et précieux, et montrent de nombreux indices d’assimilation des roches hôtes. La paragenèse minérale primaire inclut le plagioclase, l’olivine, le clinopyroxène, les oxydes ferro-titanés et accessoirement et localement, l’orthopyroxène, la biotite et l’apatite : cet assemblage est surtout préservé au coeur de l’intrusion (sous-unité centrale). Le gisement de Cu-EGP de Marathon, situé principalement dans la sous-unité supérieure, comprend une minéralisation disséminées à sulfures de fer, cuivre, nickel, et minéraux du groupe du platine, dérivés de sulfures magmatiques primaires par remobilisation hydrothermale. L’enrichissement en Cu et EGP résulte du remplacement d’oxydes ferro-titanés primaires par réaction avec des fluides tardi-magmatiques, et des fluides assimilés le long de la bordure inférieure de l’intrusion, dérivés de la fusion partielle des xénolites et de remobilisations hydrothermales."

Jan 1, 2001

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By S. Banisi, E. Arghavani, A. Akbari, Gh. A. Parsapour, S. Darvish Tafvizi

The new copper processing plant of the Sarcheshmeh copper complex consists of two parallel circuits. After a primary crushing, the ore is sent to a SAG mill and the product is further ground in a ball mill. The overflow of the hydrocyclones is fed to a flotation circuit which contains 8 rougher tank cells (RCS130), 3 cleaner cells (RCS50), 5 scavenger cells (RCS50) and a 4 x 12 m flotation column as recleaner. The circuit was initially designed to process a feed containing 0.8% Cu, but because of the ore type change, the feed grade decreased to 0.6% Cu. This resulted in a reduction of final concentrate grade and recovery from 28 and 85.5% to 24 and 84.4%, respectively. Based on the original design, the copper and silica recovery in the cleaner cells should be 69 and 55%, respectively, but these values increased to 85 and 75% because of a higher retention time. The rather high silica recovery (i.e., 75%) was found to be the main source of the lower final concentrate grade. In order to reduce the retention time of particles in the cleaner cell from 13.7 to 6.9 min, the rougher concentrates of two parallel circuits were fed to only one cleaner-scavenger and regrind circuit. This modification increased the cleaner and final concentrate grade from 15.1 and 24.5% to 17 and 26%, respectively. To prevent a possible reduction in the copper recovery, the froth depth in the scavenger cells was reduced. The overall outcome of the circuit modification was evaluated to be a 10% reduction in the energy consumption without any loss in the overall copper recovery.

Jan 1, 2016

By R. C. Beard

"The Ontario Ministry of Natural Resources has recently initiated several incentive programs to encourage and facilitate the development of new mines in northwestern Ontario. Some are privatized out to consultants and contractors. The status of three of these programs will be reviewed in this paper.IntroductionOne of the main objectives of the Mineral Resources Group of the Ontario Ministry of Natural Resources is to encourage and assist mineral exploration and the development of new mines in the Province. Programs to accomplish this objective are largely carried out through two Branches in the main office (in Toronto), the Mineral Resources Branch and the Ontario Geological Survey, and also a number of regional field offices scattered across Ontario.The function of the Mineral Resources Branch is to identify and administer effective policies that will ensure maximum benefits to the Province from mineral resource extraction.One of the most important factors in ensuring effective exploration in the Province is the availability of a good geosciences data base from which to work. It is the responsibility of the Ontario Geological Survey to develop and continually update this data base, providing, to both the public and private sector, an inventory and analysis of the geology and mineral deposits of the Province.The main functions of the regional field offices are to provide technical data and advice to exploration companies and prospectors, to encourage and assist exploration, and to provide information and general assistance to producing and developing properties to facilitate resource development and extraction. This is accomplished through the offices of the mineral resource coordinators and resident geologists. In northwestern Ontario, these field offices are located at Thunder Bay, Kenora, Red Lake and Sioux Lookout.To accomplish their objectives, the Ontario Geological Survey and the regional field offices carry out regular, ongoing geoscience and other mineral resource programs, under their base funding."

Jan 1, 1982

By Ray Collier

MINING TODAY l EXTENSIVE AND EXPENSIVE PERMITTING PROCESSES WITH UNKNOWN RESULTS l GENERAL AND IMPASSIONED RESISTANCE TO RESOURCE BASED INDUSTRY l SOPHISTICATED, ORGANISED, AND WELL FUNDED OPPOSITION l MOST LOCAL GOVERNMENT DOESN?T WANT MINING TODAY?S TALK l FOUR SPECIFIC OPERATIONS ON WHICH OUR EXPERIENCE IS BASED ? SECHELT ? CADMAN ? GRANVILLE ISLAND ? LEHIGH CEMENT DELTA PLANT l OUR APPROACH TO COMMUNITY RELATIONS

May 1, 2002

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By Stratton-Crawley R., G. E. Agar

"A study has been done of the scale-up of laboratory bench-scale flotation to continuous plant circuit performance. It was found that the impellor speed and the air flow rate influenced the results and in this case extreme values of these operating variables were required in order to reproduce the plant rougher results in the laboratory. Despite the experimental uncertainty introduced by these extreme values, it was demonstrated that the plant performance could be predicted and experimentally reproduced with bench-scale tests.IntroductionThe mineral processing industry relies heavily on batch flotation testwork to design flowsheets, evaluate reagent s and compare various types of ore. The batch tests are generally regarded as being directly comparable within themselves, but quite often they relate poorly or not at all to continuous circuits. Obviously this dilemma generates considerable uncertainty with wide-ranging ramifications. One of the manifestations of this unfortunate situation is the commonly expressed opinion that ""it may work that way in the laboratory, but it will never work that way in the plant"".In a previous publication, a method was described whereby the results of batch bench-scale tests could be used to simulate a locked cycle flotation test series. The work to be described here is a continuation of that investigation with an extension to the simulation of an actual plant circuit. It would have been preferable to progress from laboratory batch data to a continuous pilot plant and then finally to a full-scale plant operation. However, because that possibility did not present itself, an attempt will be made to show that the performance of an existing plant circuit can be successfully simulated from batch data. The success of the procedure can be judged by the agreement among the plant results, a locked cycle test and the predicted results based on batch tests."

Jan 1, 1982

By Alexander Smith

"The three principal known mineral deposits of the Taku River area lie in the Tulsequah synclinorium. The axis of this north-south trending structure is along Tulsequah River valley; about 6 miles east of the eastern contact of the Coast Range batholith.The one proven mine of the area, the Polaris-Taku, is on the west side of the valley. It is a gold property, the gold occurring in fine needles of arsenopyrite disseminated in carbonatized volcanics. The mine was originally called the Whitewater, and the adjacent area the Whitewater gold belt. During the years 1937 to 1942 gold having a value of $3,284,000 was produced from 313,500 tons of ore milled."

Jan 1, 1954

By C. H. Lee, T. T. Wang

"Exampling of the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, this study investigates the application of the Drilling Survey System (DRISS) in both Drilling and Blasting (D&B)- and Tunnel Boring Machine (TBM)-excavated sections. In the D&B section, a nonlinear relationship exists between drilling energy and uniaxial compressive strength of rock mass, in which a reasonable coefficient of determination can be analyzed statistically. Additionally, the DRISS accurately predicted an unfavorable section with a valuable position. The magnitude of uniaxial compressive strength back calculated using DRISS data also matches those acquired from geological investigations with different approaches. Study results indicate that the DRISS is an effective tool for fore-probing of both D&B- and TBM-excavated tunnels. INTRODUCTIONModern advancements in geological and geophysical investigations, and drilling techniques, have provided valuable information for detecting and interpreting geological conditions of rock tunnels with a resolution of several to ten of meters (Brückl et al., 2001, 2008, Lorang et al., 2005). Nevertheless, construction risks remain considerable during tunnel excavation, especially when a tunnel was excavated by a Tunnel Boring Machine (TBM). Predictions of the local fault, shear zone, and other minor geological features, which may cause moderate collapse or excessive deformation of rocks surrounding the tunnel, before tunnel excavation is highly desirable for high-quality tunnel construction and economically efficient project management.Rather than conventional geophysical prospection methodologies, which always favor large-scale investigation with moderate precision, this study focuses on the drilling method probing ahead of a tunnel. The goal of such an investigation is not only to prevent catastrophic collapse, but also to provide quantitative or semi-quantitative information for estimation of the mechanical parameters of rock mass.For the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, a drilling survey system is adopted for fore probing. Data collected from both drilling and blasting (D&B) and TBM-excavated sections are analyzed statistically and discussed. The applications of the Drilling Survey System (DRISS) are addressed accordingly."

Jan 1, 2015

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By L. Sun

Recently, micro-tubular solid oxide fuel cells (SOFCs) have attracted the attention of many researchers because of their numerous advantages over larger tubular and planar SOFCs. These include excellent thermal shock properties giving rapid startup/shutdown capability, a high volumetric power density compared to larger tubular SOFCs, and reduced sealing problem compared to planar SOFCs. In order to screen cathode materials for micro-tubular SOFCs, the perovskite cathodes were deposited, using a variety of methods, on 10.5 mol % yttria-stabilized zirconia (YSZ) tubes. Their electrochemical properties were then evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods, based on a three electrode configuration, and with the reference electrode position carefully optimized. The oxygen reduction reaction kinetics at the cathode/electrolyte half cell were then investigated in detail.

Jan 1, 2005

By Kallioinen Jouko

"Advanced Flotation Technology is the application driven design of Don-Oliver flotation cells to achieve the optimum performance for each type and grind of flotation. Optimum performance is the combination of both recovery and selectivity.Optimized performance is the combined product of optimized mixing and effective froth removal. Optimized mixing is applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Effective mixing for fine material is easy, but overmixing reduces selectivity in frothbed.Selectivity in flotation is an important target, especially when treating complex ores, and parameters in frothbed have been examined to improve the separation of minerals and eliminate circumstances that reduce separation rate.Advances in process control have been achieved with expert controls and instructive operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed to be used in future process development work. Excellent results of this Advanced Flotation Technology have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified."

Jan 1, 2000

By M. D. Johnson, R. K. Bezys

"The majority of Ontario's limestone and dolostone production comes from a few Paleozoic carbonate units. In eastern and central Ontario, Ordovician rock units, which are the main sources for production, include the Oxford, Gull River, Bobcaygeon, Verulam, and Lindsay Formations. They are predominantly utilized for aggregate and cement manufacturing, with the Bobcaygeon Formation being used as a source of building stone. Along the Niagara Escarpment, the Silurian Lockport, Amabel, and Guelph Formations are sources for the limestone industry. The largest tonnage of rock extracted by the industry comes from these Silurian units, especially the Lockport and Amabel Formations. These units are used primarily for aggregate, although they are also a source for lime. In southwestern Ontario, the Silurian Bertie Formation and Devonian strata, represented by the Bois Blanc Formation, Onondaga Formation, Detroit River Group, and Dundee Formation, contribute to Ontario's production of lime, cement production and crushed stone. The Detroit River Group (Lucas and Amherstburg Formations) is the main source of the lime and cement produced in the province.Northern areas, which may become significant sources for the industry, include Manitoulin Island, the Lake Timiskaming area, and the James Bay Lowland. IntroductionThe Engineering and Terrain Geology Section of the Ontario Geological Survey has undertaken a geological inventory of all active and abandoned limestone and dolostone quarries in Ontario. This geological study, combined with a commercial study of active quarries carried out by the consulting firm of Derry, Michener, Booth and Wahl, will provide an up-to-date report on the industry in the province and will be published by the Aggregate Resources Section of the Ministry of Natural Resources. This report will follow the format and style of D.F. Hewitt's Ontario Department of Mines Industrial Mineral Reports and Circulars (Hewitt, 1960, I964a, 1964b, 1964c; Hewitt and Vos, 1972). Examinations of the quarries were carried out by geologists in the Paleozoic I Mesozoic Geology Subsection of the Engineering and Terrain Geology Section, and include, in addition to the authors, R,R. Wolf, V.A . Mazur, and D.K. Armstrong in the summer of 1986."

Jan 1, 1988

By Charles Kocsis

Over the last few years a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell powered equipment into underground mines to replaced diesel engine powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine?s energy consumption, its associated greenhouse gas impact and also reduce a mine?s significant ventilation associated costs. Fuel cell powered equipment also has the advantage of lower noise and heat production compared to their equivalent diesel powered counterpart. The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions and minimum velocity requirements. However another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations these factors change, dispersion and buoyancy are limited; time may not be available and in non-coal mines ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical, consequently ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation such as a hydrogen leak from the fuel cell stack or its distribution system.

May 1, 2007

By W. A. Crosby, W. K. Smith, K. L. McDonald

"IntroductionThis paper describes how the introduction of two blasting techniques and the resuItant development of new dragline digging methods have increased the productivity of single- and double-seam dragline operations at the Rietspruit opencast mine.LocationRietspruit , one of South Africa's largest opencast strip mines, is situated some 11 5 kilometres east of Johannesburg in the Witbank coal field.BusinessRietspruit is a joint venture between Transvaal Consolidate d Land and Exploration Company (T.C.L.) and Shell, South Africa. Rietspruit is administered and managed by Rand Mines, the Mining division of Barlow Rand, transportation and marketing being the responsibility of Shell. The total saleable coal product, approximately 5,5 million tons per annum, is exported via Richards Bay.Presplitting and Throw BlastingPresplitting was initially introduced in September 1980, as a means of dewatering t he overburden and mid burden to facilitate the use of dry-mix explosives a s opposed to slurry explosives.The utilization of the throw blasting technique arose as a direct result of observed ground movement after the successful introduction of presplitting. The first trials commenced in March 1981 on the double-seam operation. The methods, economics and resulting advantages are fully described elsewhere. A brief description follows.Method of PresplittingAfter determining the desired presplit line, 250-mm holes are drilled to top of coal at 4-m to 6-m intervals, dependent on the competency of the rock overlying the coal. A single 60-kg charge of slurry explosives is located at the bottom of each hole, no tamping is used and all the holes are detonated simultaneously. The results are a competent, straight, vertical highwall. This enables accurate control of the first row of blast holes closest to the highwall, which is a prime requisite for successful throw blasting."

Jan 1, 1983