Search Documents

By G. Tozsin

A six-stage sequential leaching procedure was used to assess the leachability of heavy metals from waste rock in Antamina Mine. Sequential extractions procedure is well established for fine and small (? 1g) samples. However procedures for coarse and large test samples are lacking. This study presents results of the sequential leaches tests conducted on relatively coarse and large representative samples in terms of the availability and mobility of metals. Selective chemical reagents were used to extract metals from six different fractions where metals released with each subsequent extraction are believed to be bound tighter than those released in prior steps and therefore less likely to be leached.

Aug 1, 2013

By R. Barbaroux, B. Dubreuil, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"As conventional, base or precious metal ores are being depleted worldwide, the mining industry is being faced with an increasing exploitation of arsenical sulfidic ores. Enargite is a common example. The downstream processing of these ores poses several problems ranging from high smelter penalties to finding economical and environmentally acceptable means of disposing of the arsenic. Several hydrometallurgical processes have been proposed for extracting arsenic from enargite concentrates, notably using alkaline sulphide leaching (ASL). However, few alternatives exist for removing the arsenic from solution and stabilizing it in an approach that is both economical and environmentally acceptable.Dundee Sustainable Technologies (“DST”) has developed a technology for the sequestration of arsenic by vitrification. Originally optimized to cost-effectively stabilize arsenic trioxide (As2O3), DST has shown that vitrification could be successfully extended to the stabilization of other arsenical products, such as calcium arsenate (Ca3(AsO4)2) and sodium arsenate (Na3AsO4). In this paper, the vitrification of arsenic in the context of an enargite leaching was newly explored and demonstrated successfully.Two processing routes are being proposed by DST for the removal of arsenic from enargite concentrates and their stabilization by vitrification. In one route, arsenic is extracted by ASL and is then precipitated under atmospheric conditions and with minimal use of reagents and time. The resulting precipitate is an unstable hydrated ferric arsenate (FeAsO4•2H2O) that is then vitrified in a non-dilutive method, significantly increasing the stability of arsenic and meeting the TCLP guideline. Unlike is required for scorodite, stabilization was successfully achieved without concern for the crystallinity of the precipitate."

Jan 1, 2017

By P. E. Weidmark

"CANMET InformationPART 1-Published PapersAsmis, H. W., ""The dynamic response of caverns in discontinuous rock""; Proc 22nd U.S. Symposium on Rock Mechanics, Cambridge, Mass, June 1981, 272-277; 1981.Austin , M.W., Bray, J.W. and Crawford, A.M., ""A comparison of two indirect boundary element formulations incorporating planes of weakness"" ; Technical Note; Int J Rock Mech Min Sci Geomech Abstr; 19:339-344; 1982.Barrett, J. R., ""Applying geotechnical theory to underground metalliferous mining""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 210-222; 1983.Barron, K., Wright, P.L. and Smales, T., ""Guideline s for the design of coal pillars in the No .4 seam at Mclntyre Mines Ltd ., Grande Cache, Alberta""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of A IMMPE; 559-578; 1983.Bauer, A., ""Wall control blasting in open pit mines""; Mining Engng; 34:155-158; 1982.Bieniawski, Z.T., "" Improved design o f room-and-pillar coal mines for U.S. conditions""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 19-51; 1982.Blackwell, G.H. and Calder, P.N., ""Practical aspects of wall stability at Brenda Mines Ltd., Peachland, BC""; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-A1ME; 3:573-608; 1982.Blake, W., ""Microseismic monitoring for underground stability "" ; Proc 1st Intnl Cont on Stability in Underground Mining; Vancouver , BC, August 1982; SME of AIMMPE; 272-294; 1983.Brawner, C.O., ""Stabilization of rock slopes"" ; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-AIME; 3:289-310; 1982.Bridges, M.C., ""Review of open stope mining in Australia""; Proc 1st lntnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 813-828: 1983."

Jan 1, 1983

By J. A. McCamley

Gypsum scrap generated from wallboard manufacturing, construction and deconstruction activities in North America, Europe and Japan is a recognized environmental problem. Landfill disposal of this gypsum scrap is problematic, with deposits often creating hydrogen sulphide emissions and metallic sulphide groundwater leachates. Of these regions, Europe is the most advanced in dealing with the issue having enacted legislation, which will come into effect in July 2005 that will strongly encourage gypsum recycling throughout the EU. An estimated 10% to 17% of all gypsum used in the wallboard industry becomes recyclable scrap, which represents approximately 1% of the total waste stream in North America. In the United States, 2.5 to 4.5 Mt of gypsum scrap is generated each year; the volume is similar in Europe (the percentage of total tonnage is less because of the higher use of brick and concrete). The Greater Vancouver region of British Columbia has banned gypsum from its landfills, and as a result, all gypsum scrap is now recycled. New West Gypsum Recycling, a Canadian firm, uses its proprietary technology to process large quantities of gypsum scrap that is reincorporated into new wallboard, at percentages ranging up to 25%. The operation of New West Gypsum Recycling Inc. of Langley, Vancouver is examined as a case study and recommendations are provided as to how other urban regions can implement similar gypsum scrap recycling programs.

Jan 1, 2004

By J. C. Kurnia

Methane is recognized as one of the prime causes of underground mine disasters around the globe. A cost-effective mine ventilation system and methane control is required to ensure a safe and productive environment in an underground mine whilst keeping energy usage and operating cost at minimum. Typically methane enters a mine environment or tunnel from localized distributed sources at high initial concentration. Hence, an understanding of its dispersion from discrete sources is important to design a methane management system via effective ventilation. This study employs computational fluid dynamics to model methane dispersion in an underground tunnel which has a number of discrete sources of methane and effective ways to dilute and or disperse it. Air flow distribution within the tunnel as well as methane dispersion is simulated by solving the governing transport equations subject to appropriate boundary conditions. First, the effectiveness of ventilation duct placement is examined. Several possibilities are explored and investigated. It is found that the common configuration utilized in underground mine performs best as compared to other configurations in maintaining the concentration of methane below permissible levels. Next, a novel intermittent airflow ventilation system is proposed and evaluated via simulation with the goal of reducing the energy cost whilst maintaining methane level in the mining face below the allowable level. Parametric studies are conducted to investigate effects of various factors influencing the effectiveness and performance of this novel intermittent ventilation system. This study will provide some new ideas for designing an efficient and effective underground mine ventilation system by lowering the net average amount of air that needs to be circulated in the tunnel for a safe operation. KEYWORDS

Aug 1, 2013

By D. W. McDonald, L. M. Heaman, R. A. Creaser, T. Davies, T. Chacko, A. Simonetti

"The Three Bluffs gold deposit is located in the Committee Bay greenstone belt, which forms part of the Rae domain of the western Churchill province, Nunavut, Canada. Gold mineralization is hosted by iron formation of the Neoarchean volcanosedimentary Prince Albert Group, and is associated with silicification (quartz veining) and sulfidation of magnetite and other Fe-rich minerals. Conventional U-Pb zircon dating of a conformable dacite unit within the volcanosedimentary host-rock sequence and a crosscutting diorite intrusion confirm a ~2.7 Ga age for deposition of the supracrustal package. U-Pb monazite dates and Pb isotopic analyses of sulfides were obtained by laser ablation-multicollector-inductively coupled plasma-mass spectrometry (LA-MC-ICP-MS). A subset of U-Pb monazite (1813.8 ± 8.7 Ma) and Re-Os arsenopyrite (1822 ± 21 Ma) dates, combined with a Pb-Pb secondary errorchron age for pyrite and arsenopyrite (1829 ± 77 Ma), suggest that gold mineralization associated with sulfidation of the iron formation occurred at ~1815 Ma, prior to high-grade (upper amphibolite facies) tectonometamorphism in the Three Bluffs area (D2TB/(M2TB). An ~1815 Ma age for deposit formation is broadly consistent with evidence from elsewhere in the western Churchill province and to the southwest in Manitoba and Saskatchewan for a late Trans-Hudson (1.9-1.8 Ga) gold mineralizing event. The majority of U-Pb monazite ages form a second population at 1780.6 ± 4.2 Ma, similar to the age of the majority of Re-Os arsenopyrite analyses (1763 ± 11 Ma). These dates are thought to reflect the timing of peak M2TB metamorphism. 40Ar/39Ar dating of amphibole, biotite, and muscovite yielded plateau ages ranging from 1723.8 ± 9.0 Ma to 1710 ± 17 Ma, which are interpreted to record the timing of postpeak metamorphic cooling to below the respective closure temperatures for Ar diffusion in these minerals. Le gîte aurifère de Three Bluffs est situé dans la ceinture de roches vertes de Committee Bay, laquelle appartient au domaine de Rae dans l’ouest de la province de Churchill, au Nunavut, Canada. La minéralisation aurifère est encaissée par des formations de fer d’âge Néoarchéen appartenant aux roches volcanosédimentaire du Groupe de Prince Albert; la minéralisation est associée à de la silicification (veines de quartz) ainsi qu’à la sulfidation de la magnétite et d’autre minéraux riches en Fe.Les résultats de la géochronologie U-Pb conventionnelle sur une unité de dacite concordante au sein de la séquence volcanosédimentaire ainsi que d’une intrusion de diorite qui les recoupe indiquent que ces roches supracrustales ont un âge de ~2.7 Ga. Les âges U-Pb de la monazite ainsi que les analyses des isotopes du plomb des sulfures ont été obtenus par ablation laser (LA-MC-ICP-MS). Certains des âges U-Pb obtenus à partir de la monazite (1813.8 ± 8.7 Ma) et des âges Re-Os retournés par l’arsénopyrite (1822 ± 21 Ma), en association avec l’âge indiqué par une isochrone à données dispersées « errochron » secondaire Pb-Pb pour la pyrite et l’arsénopyrite (1829 ± 77 Ma), suggèrent que la minéralisation aurifère associée à la sulfidation de la formation de fer s’est formée vers ~1815 Ma, avant que l’événement tectonométamorphique (D2TB/(M2TB) de niveau élevé (faciès des amphibolites supérieures) affecte le secteur de Three Bluffs. Un âge de mise en place de ~1815 Ma pour ce gîte est compatible avec les données en provenance de l’ouest de la province de Churchill ainsi que plus au sud-ouest au Manitoba et en Saskatchewan qui indiquent la mise en place de minéralisations aurifères à la fin de l’orogénèse Trans-Hudsonienne (1.9-1.8 Ga).La majorité des âges U-Pb de la monazite constituent une seconde population formée à 1780.6 ± 4.2 Ma, ce qui est similaireLà l’âge obtenu pour la plupart des analyses Re-Os sur l’arsénopyrite (1763 ± 11 Ma). Ces âges reflètent probablement l’atteinte du pic métamorphique M2TB.La géochronologie 40Ar/39Ar de l’amphibole, de la bio"

Jan 1, 2009

By Seppo Haapamaki

"Since it started production in 1970, Anderson Lake Mine has experienced several radical changes in mining methods as a result of the physical characteristics of the ore zone along with the need for improved productivity. This paper examines the transition from longhole open stoping to mechanized cut-and fill then to vertical crater retreat at Anderson Lake Mine. The reasons for the need to change mining methods is analyzed taking into consideration the impact of such criteria as improved productivity and ground conditions and how these criteria affected the over-all economic viability of the mine. IntroductionAnderson Lake Mine is one of five producing copper mines in the Snow Lake area and is situated approximately 3 km southeast of the townsite of Snow Lake (Fig. I).The mine production rate at Anderson Lake is 700 tpd and all ore is trucked from the mine to the mill located approximately 2.5 km from the mine site . The mine is serviced by a three-compartment shaft sunk to a depth of 3300 ft with level spacings at 175 ft and 150 ft intervals from the 600 ft level to the 3000 ft level. .The shaft was collared in 1965 and, a year later, the hoist and compressors were installed. By 1969, a crusher system had been built and actual production began in 1970. During 1978, production was suspended for the year to allow for 430 ft of shaft deepening."

Jan 1, 1988

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminicki, D. Evans-Lamswood

"Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite. La caractérisation systématique de la minéralogie des gîtes de sulfures massifs peut fournir des indications précieuses sur la genèse des minerais et le traitement métallurgique qui ne seraient pas disponibles par d’autres méthodes. Nous décrivons un procédé par lequel (1) un algorithme est utilisé pour calculer l’abondance de minéraux normatifs à partir d’analyses lithogéochimiques, (2) les résultats sont exprimés dans des blocs diagrammes, (3) les résultats sont par la suite validés par analyse d’image automatisée sur un microscope électronique à balayage en électrons rétrodiffusés et par cartographie en rayons X sur des échantillons constitués de grains montés en résine, et (4) les résultats de cette validation sont combinés aux données texturales obtenues par microscopie optique.Cette technique est appliquée aux sulfures magmatiques de Ni-Cu-Co du gisement Ovoïde, en utilisant les analyses géochimiques de 3175 échantillons de roche totale. L’Ovoïde comprend trois types de minerai. Le type I est situé au centre du gisement; il est riche en magnétite et pauvre en pyrrhotite avec des quantités intermédiaires de pentlandite et de chalcopyrite. Le minerai de type II entoure le minerai de type I et est riche en pentlandite et en chalcopyrite avec des quantités intermédiaires de pyrrhotite et de magnétite. Le minerai de type III se trouve à la base ainsi qu’à bordure externe de la partie nord du gisement; il est riche en pyrrhotite et pauvre en chalcopyrite, avec un contenu intermédiaire en pentlandite et une quantité faible à moyenne de magnétite."

Jan 1, 2012

By Ainul Akhtar, Steve Cockcroft, Daan Maijer, Carl Reilly, Lu Yao, Jun Ou

A coupled thermal-fluid flow-multicomponent model has been developed to aid in understanding the melting/dissolution behavior of solid Al-rich Material (TiAl) in a liquid titanium pool produced by an electron beam. The model is capable of accounting for the significant phenomena present affecting heat, mass and momentum transport including thermal and compositional buoyancy and Marangoni forces, Darcy attenuation, evaporation, melting and solidification, and the associated release or absorption of latent heat. The modeling results have indicated the compositional fluid flow driving forces (compositional buoyancy and Marangoni forces) contribute significantly to the melting/dissolution process. The model is waiting for validation against empirical data.

Jan 1, 2014

By K. Sugawaral, W. Tongampl, K. Hiruta, Takasaki Y., A. Hosoi, T. Katol, A. Shibayamal

Printed circuit boards of discarded personal computers, televisions, mobile phones and so on contain a significant amount of valuable metals. For the recycle of valuable metals contained in the printed circuit board wastes (P CB W), the effect of temperature on chlorination-volatilization of metals under chlorine gas flow was studied. The experimental sample used was powder of two types: crushed PCBW (Sample 1) made from PC and industrial machines, and crushed-combusted PCBW (Sample 2) made from Sample 1. The principal element in Sample 1 and Sample 2 was copper, about 13 wt% and 20 wt% respectively. Sample 1 was composed of pure metals such as copper, tin and lead. In comparison, Sample 2 consisted of oxide metals such as copper oxide, tin dioxide and silicon dioxide. The two samples were heated at predefined temperatures (ranging from 300 °C to 900 °C) in chlorine gas. The chlorine gas flow into the furnace was set at a rate of 100 mL/min. As a result, copper in Sample 1 began to volatilize at 600 °C and completely vaporized at 700 °C. While in Sample 2, copper started to volatilize at 600 °C and reached 100% vaporization at 800 °C. For Sample 1, zinc finished volatilizing at 500 °C, while for Sample 2, zinc volatilization reached only about 80% (maximum). Also, lead, nickel and titanium showed similar results. Consequently the volatilization rate of Sample 1 is higher than Sample 2 and the temperature dependency was verified for copper, lead, zinc, nickel, antimony, titanium and chromium. In fact, the volatilization rate of these metals increased with the temperature. This result reflects the difference between pure metal and metal oxide, as Sample 2 was combusted before the chlorination-volatilization test. Moreover, the chlorination reaction may be accelerated by a reductive atmosphere because Sample 1 contains carbon. In this study, the volatilization behavior of some valuable metals in PCBW by chlorine gas was observed. Further improvement in the rate of volatilization can be achieved by optimizing the experimental conditions.

Jan 1, 2011

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By R. Sage, N. Rillette, M. D. Everell, G. Herget

"CANMET has been operating as a Government Technology Centre for two years. Many of CANMET's programs involve long-term research and require special expertise, often available at Canadian universities. CANMET's involvement with universities ranges from research grants and contracts to exchanges of scientists and joint use of research facililies. Examples of CANMET - university cooperation in mining are presented. IntroductionIn the last two years or so CANMET has undergone a significant metamorphosis, resulting in greater emphasis on applied research to enhance Canada's industrial capability. CANMET's new mandate is reflected in the types of projects undertaken and their categorization, (Fig . I). Emphasis is being placed on two project categories: strategic R&D, to enable CANMET to serve the changing technological needs of the industry; and incrernental R&D, to serve the more immediate industry needs through modifications to existing technologies and knowledge. The balance of CANMET's e ffor t is devoted to providing Mandated and Specialized Services, and to Exploratory Research.CANMET interaction with universities can involve one of several available vehicles : contracts, research grants, exchanges of scientists , student employment and nomination of professors on CANMET's advisory council. Instances of key university technical support to CANMET mining projects are highlighted."

Jan 1, 1990

By L. Vollert

In-situ recovery of metals is presently experiencing a revival not seen since early applications in amenable copper oxide deposits, uranium and generally applications where neither, porosity and permeability, nor process chemistry have been prohibitively difficult. With ever decreasing grades in current mining operations or Greenfields projects and ever increasing capital and operating costs, in-situ recovery is looked to as the processing option that will both unlock these deposits as well as potentially derive revenue from mineralised waste remaining in the ground once traditional mining and processing methods become uneconomical. In-situ recovery is also being looked to as a mining method that minimises the environmental impact sustained in the application of traditional energy and water intensive mining and processing operations where millions of tonnes of ore are mined from the earth, processed on surface and then disposed of in both waste dumps and tailings facilities. The key challenge facing companies like Newcrest is that these low-grade deposits or remnant mines are generally hard rock applications that require costly methods to liberate the valuable minerals. A further challenge includes identifying suitable chemistries that both facilitate the economic recovery of gold and copper and that may be considered environmentally acceptable. This paper presents a desktop study whereby the issues of access creation and chemical extraction are discussed and evaluated with a view to driving future research in the area and unlocking this application as a real processing option. INTRODUCTION Mining companies are increasingly challenged by low grade, deep and complex ore deposits which are no longer economically exploitable by current methods. The large footprint of current open pit operations can present obstacles for permitting and social acceptance. For these reasons in-situ recovery (ISR) technologies are receiving renewed attention as a technology which could be used to exploit these more complex deposits economically and with less environmental impact. The environmental impact may be further reduced if emphasis is placed on use of renewable energy sources rather than traditional grid power, gas turbine or diesel generators are employed to drive the operation. A potential renewable energy driven ISR mine of the future is shown in Figure 1.

Jan 1, 2019

By P. Chu, J. A. Finch, R. Li

"Bubble size plays a key role in flotation. In this paper, we examine the possibility of using passive acoustic sending to determine bubble size. Software was developed based on Short Time Fourier Transformation (STFT) to analyze the frequency of the acoustic signal emitted from the bubble formation event. Bubble size was determined from the Minnaert frequency. The acoustic-determined bubble size responded to reagent dosage, but was less sensitive than that given by imaging. The constraints of the current acoustic approach are discussed.INTRODUCTIONBubble size is an important factor affecting flotation performance. It determines the maximum available surface area for collecting and transporting mineral particles. Of interest for process control (Gorain, Franzidis, & Manlapig, 1995), it can be determined by several techniques, such as image analysis (Grau & Heiskanen, 2002; Hernandez-Aguilar, Gomez, & Finch, 2002); conductivity (Barigou & Greaves, 1992); drift flux analysis using gas rate and gas holdup measurements (Banisi & Finch, 1994); and optical sensors (Randall, Goodall, Fairlamb, Dold, & Connor, 1989). However, all these techniques have drawbacks.Acoustic analysis of the oscillatory behaviour of bubbles to extract bubble size is another possibility (Leighton & Walton, 1987; Pandit, Varley, Thorpe, & Davidson, 1992; Al-Masry, Ali, & Aqeel, 2005; Manasseh & Ooi, 2009; Leighton & White, 2012; Spencer et al., 2012). The fundamental basis is the work of Minnaert (1933) who first correlated the bubble size with its natural frequency, Equation 1:"

Jan 1, 2016

By L. Xia, B. Hart, K. Douglas

In the flotation of Rare Earth Element (REE) bearing minerals, oxalic acid is reportedly acting both as a depressant and pH modifier. Testing has established the significance of oxalic acid in the flotation process however its specific role in either the recovery or selectivity of REE over their gangue minerals is not well understood. Pulp pH reduction trials with alternative acids have not shown the same effect on the REE mineral recovery or the depression of gangue phases. This work examines the effect of oxalic acid on the surface of gangue minerals (quartz and carbonates (dolomite and calcite)) in a series of conditioning tests. Gangue surface analyses by TOF-SIMS indicate that oxalic acid inhibits the transfer of secondary ions generated during the conditioning process from one mineral phase to another. In this regard, the oxalate anion acts to fix ions in solution through chelation, limiting their participation in surface adsorption.

Jan 1, 2014

By D. Sagara, V. G. Makhado

"A model based control strategy was implemented at Loulo Gold Mine in Mali, to stabilise the thickener underflow stream density. This stream acts as the feed to the leaching circuit. pH control of the leaching circuit was integrated with the model-based controller due to slow process dynamics that are not suited to PID control. The controller performance was quantified over a period of 6 months, and was compared to the performance before implementation. The model based controller reduced process variability for both thickener underflow density and pH considerably, and resulted in a reduction in flocculant and lime consumption of 9.32 and 6.55%, respectively. INTRODUCTION Reagent consumption in gold processing plants significantly contributes to the total operational costs. In a typical Carbon-in-pulp (CIP) circuit, the reagent consumption associated with leaching, adsorption, elution and regeneration contribute to approximately 15% of the total operational costs (Stange, 1999). At Loulo Gold Mine, the reagent consumption associated with leaching, adsorption, elution and regeneration contributes to 6% of the total operational costs. As such, a reduction in reagent consumption will present a significant opportunity for savings on operating expenditure. Variability in feed ore characteristics results in continuous changes in steady state operating regions, which presents process control challenges as a result of the long residence times in some of the process units associated with gold processing plants. Overdosing often occurs in the presence of process variability to ensure safe operation and to maintain recovery targets. As a means of reducing reagent consumption and accounting for significant changes in the feed to gold plants, some of the plants have resorted to improving their process control strategies around their circuits. This paper focuses on the implementation of a model predictive based controller at Loulo Gold Mine on their thickener and Carbon-in-leach (CIL) tank to: •,stabilise the thickener underflow density, and •,the CIL tank pH."

Jan 1, 2017

By Ashu Garg, Anirban Bhattacharya

"Friction stir spot welding of aluminum alloy AA6061-T6 sheets was performed with circular (plunge depths 0.4 and 0.6 mm), square and triangular tool pin (plunge depth 0.4 mm) with constant 0.2 mm shoulder penetration to characterize various zones of weld nugget. It was observed that the depth of the stir zone formed below the tool pin is comparatively similar for different tool pins but wider for circular tool pin. The size of another stir zone formed at the interface of tool pin and a tool shoulder is observed to be larger for triangular and square tool pin due to the higher swept rate. Predicted strain from finite element analysis, calculated strain rate using Zener-Hollomon relationship and experimentally measured grain size distribution indicates severe amount of plastic deformation in-and-around the nugget/spot region. Finer grains in various stir zones were observed than thermo-mechanically and heat affected zones. Grain size (at distribution peaks) in stir zones varied around 2.54 µm to 3.69 µm for different tool pin profiles as compared to base metal grain size of 20 µm. Microhardness results indicate that the welded region is quite softened than base metal and maximum hardness is mostly observed around the thermo-mechanically affected zone.INTRODUCTION Friction stir spot welding (FSSW) is widely used for joining the sheets of materials like aluminum, copper, magnesium, etc. The process begins by plunging a rotating tool (generally having a pin and a shoulder) into the sheets to be welded. Continuous stirring of the tool and downward plunging force generates localized heat due to friction at the tool-sheet interface and plastic deformation of the sheet metal. The material gets softened and the plasticized material adjacent to the tool pin starts flowing due to the action of tool rotation and tool plunge thereby causing intermixing and bonding between the overlapped sheets. The tool stirring also promotes grain refinement in the weld nugget associated with high strain, strain rate and thermal cycle. The formation of new microstructure also affects the mechanical properties and efficiency of FSSW joints. Studies also showed that the tool pin design and tool shoulder feature exerts a noteworthy influence on the material flow and intermixing during the FSSW process (Reilly et al., 2015; Hirasawa et al., 2010). Sarkar et al. (2016) studied the material flow and intermixing during FSSW using tracer material method and reported that the size and width of flow zone increases with tool penetration depth. The influence of tool rotational speed on microstructure and stir zone temperature was investigated during FSSW of dissimilar AA6061-AA5754 alloys (Gerlich et al., 2007). They reported that the average grain size in stir zone of AA6061 weld increases with increase in tool rotational speed. In another work, Gerlich et al. (2008) studied the local melting and tool slippage during FSSW of Al alloys. Tool slippage was investigated by calculating the strain rate using Zener-Hollomon relation. Garg and Bhattacharya (2017a) studied the effect of dwell time, tool pin profiles and tool rotational speed on shear strength, microstructure, temperature and strain distribution during FSSW of AA6061. In another work, Garg and Bhattacharya (2017b) analyzed the effect of different tool pins and pinless tools on the shear strength and microstructure during similar and dissimilar FSSW of AA6061-T6 and pure Cu. Chang et al. (2004) proposed mathematical relationship between the average grain size and Zener-Hollomon parameter during friction stir processing of Mg alloy. Solhjoo (2010) presented a mathematical approach to determine the critical strain as a function of peak strain required for initiation of dynamic recrystallization in austenitic stainless steel. Fratini and Buffa (2005) also proposed the numerical model to determine the grain size during continuous dynamic recrystallization phenomenon."

Jan 1, 2018

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010