Search Documents

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

By G. V. Theja, V. B. Maji

Large infrastructure projects like tunnel excavations, underground constructions face innumerable risks. For successful completion of these projects, it is essential that we foresee and understand risks that could occur during different phases of the project. One of the risks affecting underground excavation projects is the inaccurate performance prediction of TBMs. As this could severely affect the project, resulting in lower advance rates and could also result in changing the excavation machine or method, due to difficulties in excavation, thereby increasing the overall cost of tunnelling. This makes performance prediction of the TBMs as one of the crucial aspects in tunnelling, as a precise estimation of its performance is required for planning and estimation of time and cost of the tunnelling projects. This performance prediction of TBM is a challenging geotechnical problem that is intricate and complex in nature, this is possibly due to the fact that TBM performance prediction involves understanding the rock fragmentation process in wide range from micro-scale (i.e. the interaction of surface of rock material and cutter tip) to macro-scale (including the interaction of rock mass and TBM). Thus in order for the performance prediction model to be efficient, parameters of both TBM specifications and ground conditions have to be considered. Various models have been proposed by researchers since the early phases of TBM application, these studies resulted in the development and improvement of numerous penetration prediction models. Most of these models consider the geotechnical parameters that are input to the model to be consistent along the TBM drive and neglect the uncertainties in parameters that occur. And so to improve the predictive capability of these models and to incorporate the above uncertainties, the penetration rate is modeled as a stochastic variable depending on the geotechnical and TBM parameters, its statistical distribution is determined and is used to characterize the penetration rate instead.

Jan 1, 2015

By H. T. Michels

Recent laboratory studies show that several bacteria, known to be human pathogens, die when they come in contact with copper and copper alloy surfaces. The amount of live bacteria drops by several orders of magnitude, to zero, on copper alloys in a few hours. In contrast, no reduction is seen in the concentration of live organisms on stainless steel during the six-hour test period. Aluminum painted and coated surfaces and plastics would show behavior similar to stainless steel and show no effect. Coatings and other surfaces claiming to be antimicrobial showed little to no effect. These results suggest the selection of copper alloys for surfaces exposed to human touch can materially assist in reducing the transmission of infectious organisms. In order to make antimicrobial claims in the United States, the approval of the US Environmental Protection Agency (EPA) is required. The EPA-required efficacy testing is described and the test results are summarized. It is anticipated, that once regulatory approval is obtained, that this will facilitate the introduction of antimicrobial copper alloys in hospitals, nursing homes and other healthcare facilities, as well as schools, and public buildings. Some of the application and barriers, to entry into the healthcare markets are mentioned.

Jan 1, 2007

By M. J. Fairweather

"The nature of minor element values and impurities are important both in the assessment of new properties and in the continuing improvement of operating plants. Impurity elements are frequently present as fixed solid solution impurities in association with the constituent minerals of a deposit or process streams in a concentrator. This paper uses five case studies to illustrate the application of simple regression analysis to the evaluation of minor element distribution in both operating mines and new deposits using analytical information readily available. This information maybe used to determine opportunities for improvements to the performance of an operating mine, to the economic assessment of anew deposit, or to the subsequent planning of an experimental study.IntroductionThe nature of minor element values and impurities are important, both in the assessment of new properties and in the continuing improvement of operating plants. Minor element values often contribute appreciable incremental revenue to a complex base metal deposit. Examples of valuable elements include precious metals, but may also include elements such as indium and bismuth which can be recovered at a profit by smelters provided with the necessary recovery circuits. During preliminary metallurgical studies of a new property there is usually a strong incentive to maximize the recovery of such valuable by-product elements. For example, the extent to which the by-product gold in a porphyry copper deposit is associated with chalcopyrite rather than pyrite may determine theeconomics of developing a new property.The nature of impurity elements in base metal concentrates is correspondingly important in minimizing the penalties which may be imposed by smelters in the treatment of such concentrates. Penalty elements include silica, dolomite (magnesia), arsenic, antimony, mercury, nickel and cobalt. The mineralogical association of these minor elements determines the ability of the mine to remove them in the concentrating process. This paper discusses means of assessing the mineralogical nature of such impurities without the use of sophisticated micro-analytical techniques."

Jan 1, 1997

By Cheng-Ting Chiang

Information integration and exchange for the entire building life cycle is one of the most important issues in the AEC industry. Although the Building Information Model (BIM) technology is widely utilized to address them, BIM is mainly concerned within the design and construction (D&C) phases. In the operation and maintenance (O&M) phases, however, the information integration and exchange issue becomes more complicated because software applications here require not only BIM but other information outside of the AEC domain, e.g., disaster mitigation. Nowadays, most BIM-related research focuses on the D&C phases and pays less concern on the O&M phases, hence there is a research need that can help seamlessly transfer the information between the D&C and O&M phases. In this research, a software framework using ontology was designed to deal with aforementioned problems. The BIM data from the D&C phases were used as a foundation to generate new models for different software applications for the O&M phases. The ontology technique was employed to assist the model transformation process between the original BIM and the models for applications. Finally, a disaster mitigation example was chosen to validate the framework, in order to make sure that the transformation process is comprehensive and useful from domain experts? perspective.

Aug 1, 2013

By J. H. Reiss, D. F. Bruhn, Idaho National Laboratory, Y. Jiao, D. W. Reed, Y. Fujita, D. L. Daubaras

"Bioleaching offers a potential approach for recovery of rare earth elements (REE) from recyclable materials, such as fluorescent lamp phosphors or degraded industrial catalysts. Microorganisms were enriched from REE-containing ores and recyclable materials with the goal of identifying strains capable of extracting REE from solid materials. Over 100 heterotrophic microorganisms were isolated and screened for their ability to produce organic acids capable of leaching REE. The ten most promising isolates were most closely related to Pseudomonas, Acinetobacter and Talaromyces. Of the acids produced, gluconic acid appeared to be the most effective at leaching REE (yttrium, lanthanum, cerium, europium, and terbium) from retorted phosphor powders (RPP), fluidized cracking catalyst (FCC), and europium-doped yttrium oxide (YOEu). The Acinetobacter isolate, BH1, was the most capable strain and able to leach 33% of the total REE content from the FCC material. These results support the continuing evaluation of gluconic acid-producing microbes for large-scale REE recovery from recyclable materials.INTRODUCTIONAn enhanced recovery, substitute, reuse or recycle paradigm is important for balancing the supply and demand of critical materials (DOE, 2011). The recovery of rare earth elements (REE) from recyclable materials is an important component in this model. REE are used in a variety of modern products. For example, neodymium, europium, terbium, dysprosium, and yttrium are important for applications such as permanent magnets, lamp phosphors, rechargeable batteries, etc. (Binnemans, Jones, Blanpain, Van Gerven, Yang, Walton, & Buchert, 2013; DOE, 2011; Graedel, Harper, Nassar, & Reck, 2013). Cerium and lanthanum are used in glass polishers and additives in fluidized cracking catalysts (FCC)."

Jan 1, 2016

By Michael Cullen

The Quinsam Coal Mine is in the process of extracting a panel beneath the mine access road. To prevent damage to the road, and adjacent powerline, it was necessary to establish a ?protection zone? within which the extent of mining would be limited. The protection zone is analogous to the setback limit. For economic reasons it was desirable to make the protective zone as small as possible, and with the greatest extraction ratio possible. The size of the protective zone was established by determining the angle of critical deformation using the numerical model FLAC, coupled with field data on subsidence from the Mine. The angle of critical deformation (defined as the angle, measured from the vertical, at which intolerable damage is sustained by a structure) was determined to be between 0 and 5 degrees. The allowable extraction ratio in the protection zone was established using the ARMPS method of pillar design coupled with field data on pillar stability from the Mine. Excavations spans to prevent caving were determined by historical experience and field data on span stability from the Mine, coupled with numerical modeling. The minimum pillar size was determined to be 7.5m. The maximum pillar height was established at 2.5m. The maximum allowable excavation span was determined to be 8.5m. With these criteria, extraction ratios between 54 and 73% (measured in plan view) were determined to be appropriate for the protection zone.

May 1, 2001

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By Arthur Lieu

Outline Removal mechanisms of Se and Mo in the Key Lake Bulk Neutralization circuit Bulk circuit Detail process modification in the Key Lake BN circuit Process performance after commissioning Objective Legacy effects of Se and Mo from the historical operation of Key Lake mill were shown to have an negative effect on the regional biota in the downstream environment. The water treatment circuit was not designed to remove Se and Mo from the effluent. Reduce Se and Mo concentrations in final effluent under0.028 0.028 ppm ppm and 0.3 and ppm ppm(CNSC regulatory limits).(limits).??????

Nov 1, 2011

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size."

Jan 1, 2016

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By J. Hedderson, J. Starkey, S. Reeves, B. Hilscher

"As ore sorting becomes more common, it is important to quantify its impact on comminution circuits in order to precisely predict its effect on throughput, grind, and mill operating conditions. Since sulphides and other valuable minerals are often softer then the surrounding waste rock, the ore kept by a sorting system is typically softer than the average ore. In order to accurately forecast production, new measurements of hardness need to be performed on the new concentrated mill feed. This paper proposes a methodology to examine this effect quantitatively at an early stage of project development using the SAGDesign test.INTRODUCTION The application of ore sorting in the mining industry is one of the most promising recent technologies with the potential to cause step change in the way concentrators are designed. Most typically, ore sorters are used to sort a given ore flow for grade, either to reject waste from the mill feed, or rescue ore from the waste pile. Ore sorting technologies have been successfully applied at many mining properties in various forms and while the technology has reached or is reaching maturity in other industries, it is still in development in the mining sector. As a result, there is not yet a general consensus on the considerations that need to be made when designing a plant with ore sorting from a feasibility level above and beyond what is commonly performed as best practice. This paper will discuss those considerations and propose a methodology for integrating ore sorting into a comminution circuit at the design phase. Due to the linearly additive nature of the SAGDesign Test results, a “hardness balance” can be developed to estimate the ore hardness which would be measured in any sorting mass split using only two data points. This will allow a design engineer to make more informed decisions as to the most appropriate mass split to select in relation to the incurred operating costs and grinding circuit sizing."

Jan 1, 2019

By Derrin A. Auerswald, Jacolien P. Wyethe, Nanne M. \/egter

Base and precious metal refineries often produce effluent solution and slurry streams containing between 50 mg/L and several grams per liter of base metals. Metals have historically been precipitated from these streams with lime to produce effluent streams at pH values between 8 and 9. This effluent treatment process generally does not remove alkali and alkali-earth metals or halides efficiently and with more stringent environmental legislation, more sophisticated effluent treatment plants must be considered which could for example incorporate sulphate removal with ultra-filtration, or the SavminTM process, followed by reverse osmosis for the removal of halides. The flowrates of effluents are often high and if base metals can be recovered before neutralization, the revenue generated from this stream can reduce the cost to produce clean water significantly, and in the case where high concentrations are disposed of, result in a profitable operation. As an add-on to an existing the plant the recovered metal is upgraded and recycled to the plant, but the production of a saleable metal can also be considered. Technology selection for metal recovery depends on the composition and flowrate of the effluent, but could incorporate resin-in¬pulp or other ion-exchange technology; precipitation as sulphides, hydroxides or carbonates; or solvent extraction. This paper describes, as a case study, the technology selection process and uses data from Zincor. Zincor is a division of Exxaro Base Metals (Pty) Limited, a subsidiary of Exxaro Resources Limited.

Jan 1, 2011

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By Narasimha Mangadoddy, Balraju Vadlakonda

"Bubble size distribution, bubble rise velocity and gas and solids hold-up are the key major hydrodynamic parameters that are extensively used for column flotation design and performance evaluation. The distribution characteristics of mean gas hold-up is studied using electrical resistance tomography (ERT) coupled with pressure transducers (PT) in column flotation. The ERT technique facilitates non-invasive and nonintrusive visualization of different flow regimes even in the presence of particles in a column flotation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas hold-up and its radial distribution has been analysed for both two-phase and three phase flows. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the three-phase flow hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, are employed to explore the influence of parameters in two phase flow in column flotation. Mean gas and solids hold-up values extracted from ERT have been critically analysed for the column operating in various flow regimes. Gas hold-ups and solid hold-ups results using ERT are in very good agreement with conventional estimation and correlations obtained using pressure transmitter methods. Meanwhile, the results show that the gas hold-ups in the centre region increase constantly with an increase in the superficial gas velocity, whereas solid hold-ups distribution is very heterogeneous for high gas velocity. Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the 'inside' flow behaviour of gas –liquid–solid three phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is perhaps the most significant technological innovation in flotation machinery and its successful introduction in mineral processing plants. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker & Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena, Biswal, Das, & Reddy, 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on performance of column flotation (Finch, J.A.;Dobby, 1991). Many techniques have been developed that could be used to experimentally analyse the hydrodynamics of column flotation. Tomography techniques are well sound to investigate the hydrodynamics for process equipment. Among that, Electrical resistance tomography (ERT) has been used in various industrial investigations for visualization of the concentration profiles and characteristics of the fluid dynamics in gas–liquid two-phase systems (Wang, Dickin, & Mann, 1999; Williams, R.A; Wang, 2000). ERT is an imaging technique to analyse the internal flow behavior non-intrusively. ERT provide very useful tools for measuring and monitoring of column flotation process on line. Due to its high speed capability, low cost measurement, robust sensors, ERT is considered to be the most powerful tool among other tomography techniques such as positron emission tomography (PET), magnetic resonance imaging (MRI), optical and infrared tomography. Application of ERT has extended in process systems due to its improved speed of data acquisition, sensitivity, flexibility and noise immunity. In multiphase flow of bubble columns, gas hold-up and solid hold-up are explored by using the coupling of ERT and difference pressure method (Jin, Han, Yang, & He, 2010)."

Jan 1, 2016

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By J. J. Quinn

Several mineral flotation plants utilize process water with high soluble salt content. The processing of semi-soluble minerals, the use of recycle streams, sea or well water give rise to this situation. It is unclear as to the overall effect on flotation response though there does seem to be evidence of bubble size reduction, increased froth stability and reduced reagent dosage. The present work aims to quantify the effects of salts present in process water on gas dispersion (bubble size and gas holdup) and froth properties. The salts examined were NaCI, CaCl2, Na2SO4, Na2S2O3 and Al2(SO4)3. Tests were conducted to determine the effects of salt type and concentration on gas holdup and bubble size distribution. The salts containing multivalent ions had a greater impact than the monovalent ions, in keeping with the literature. A relationship between gas holdup and ionic strength was established. The concentration of frother (methyl isobutyl carbinol, MIBC) giving equivalent gas holdup was determined. The effect of salt and frother combinations was also explored.Proposed mechanisms for coalescence inhibition in salt solutions are briefly reviewed in light of the current findings.

Jan 1, 2006

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By B. Jena, M. Rigaud, S. C. Panigrahy

"The influence of flux addition on the structure and properties of pellets produced from low silica specularite with peat moss and bentonite as binders was investigated. Specific pellets basicities in the range of 0.4 to 3.2 were obtained by the addition of limestone or a combination of dolomite and limestone as flux. A t basicities < 1.6, the bonding in the pellets was provided by a glassy silicate phase. At basicities =1.6, calcium ferrites were the predominant bonding phase. When dolomite was added as a flux, presence of magnesia-ferrite was noted. The reduction behaviour of pellets at different basicities was found to be influenced by the type of flux and binder. The pellet compression strength and swelling characteristics were improved with increased basicity.IntroductionThe properties of iron ore pellets are influenced by the type and nature of the ore or concentrate, additives and their subsequent treatment to produce pellets. The interaction between various constituents of the concentrate and additives, i.e. iron oxides, gangue and fluxes etc. result in the formation of various mineralogical phases which affect the degree and nature of bonding achieved in the pellet and the structure and distribution of pores. The pellet properties such as pellet strength and reducibility are influenced by the extent and type of bonding achieved between the ore particles. In view of the present emphasis on the production of high quality pellets to meet progressively stringent quality control requirements, it is essential to investigate the effect of additives on the bonding mechanism and properties of the pellets.In the past, the effects of additives on the bonding mechanism of pellets have been investigated. It is important to note that the conditions and parameters to be controlled are typical of a given concentrate/ore. In this paper, the results of the investigation on characterization of fluxed pellets produced from a low silica specularite concentrate are reported.This investigation was also aimed at assessing the suitability of peat moss for use as a binder for the production of low silica fluxed pellets. Peat moss is abundantly available in the vicinity of iron ore mines in Quebec and encouraging results have been obtained du ring the production of high silica acid and fluxed pellets."

Jan 1, 1992