Search Documents

By H. R. Taylor

The history and development of this property is more or less familiar to nearly everyone connected with the mining industry, so that only a brief outline of the more important facts will be given in this article. In 1916, a small pilot mill was constructed by the British Columbia Copper Company at Copper Mountain, and during 1916 and 1917 test work was conducted to determine the possibility of concentrating the ore and also to work out a suitable flow-sheet. In the spring of 1917, the location of a mill site at Allen by, which is about 8,% miles from Copper Mountain, and near the Similkameen river, was decided on, and the designing of a 2,000-ton plant was then worked out by Bradley, Bruff and Labarthe. Early in 1918, the actual construction of the concentrator began, and, after considerable labour difficulties, it was completed in 1920. During this period of construction, the West Kootenay Power Company ran a 60,000-volt power line over from Greenwood, a distance of 102 miles, and also built a sub-station at Allenby to take care of the mine and mill. The concentrator was started up on October 20th, 1920, and ran until December 11th, 1920, a total of 18,354 tons of ore being milled. The results of this short period of operation were encouraging, but, due to tlie prevailing low price of copper and high wages, it was necessary to shut down until a more favourable time. During the latter half of 1923, some work was done on remodelling the mill. This work continued until January 8th, 1924, when it was suspended.

Jan 1, 1929

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

"The gravimetric dust sampler is one of the tools now available to the industrial hygienists for determining the worker 's exposure to the numerous types of particulate matter that may be present in the workplace. The paper ' reviews the different sampling trains that can be used for the two major criteria for respirable dust and some of the sources of error in this dust assessment technique.IntroductionIt may be stated simply that the measurement of airborne dust in the working environment is done for one or two reasons: namely, for engineering control purposes and! or to evaluate the potential for toxicological insult arising from the inhalation of dust particles.This paper reviews the progress made in the development of dust-assessing instruments, particularly the gravimetric types designed to meet British and U.S. dust criteria , and discusses the limitations in their use for this purpose."

Jan 1, 1981

By Weng Fu, James Vaughan, Stefan Lakemond

Uranium bearing copper sulphide flotation concentrates produced from iron oxide copper gold uranium (IOCG–U) ore contains radionuclides such as 238U, 230Th, 210Pb, 226Ra, 210Po, which have the potential to reduce their marketability, thus posing a challenge to the industry. Thus, a two–stage leach process has been proposed in this study. In first stage, a sulphuric acid leach process effectively dissolve most of the 238U and 230Th into solution, but other radionulclides (mainly 210Pb, 226Ra and 210Po) remain associated with copper sulphide minerals owing to their low solubilities in sulphuric acid solution. In the second leaching stage, the use of methanesulfonic acid (MSA, CH3SO3H) is investigated to selectively dissolve the 210Pb, 226Ra and 210Po from the residue of the first stage. The results indicate that 96% of 238U, 87% of 230Th, 90% of 210Pb, 86% of 226Ra and 17% of 210Po are dissolved using 3 mol/L MSA solution at 90°C for 3 hours, which represents a dramatic decrease in the radioactivity of the copper concentrate. INTRODUCTION Australia is host to one of the largest iron oxide copper–gold–uranium (IOCG–U) deposits in the world. Most of the value in these deposits is associated with copper. In mineral processing, the gangue minerals are separated from copper sulphide minerals that report to a copper flotation concentrate. However, due to the strong association of uranium with copper minerals and hematite, even clean copper concentrates can contain significant amounts of uranium (238U) and its radioactive decay elements, of which thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) are the long life radionuclides. These hazardous radionuclides negatively affect the marketability of the copper concentrates. Customer copper smelters in China, Japan and Europe may consider the radionuclides penalty elements or may not be able to process the feed. Therefore, there is a strong motivation to remove radionuclides from copper concentrates at the mine site before shipping to custom smelters in global market. Hydrometallurgical leaching has been widely employed to remove radionuclides from different kinds of minerals such as copper concentrates (Ragozzini & Sparrow, 1987), zircon concentrates (Aral, Sparrow, McDonald, & Norgate, 2007), and coal ash (Lei, Qi, Sun, Xu, & Wang, 2014). Leaching using sulphuric acid (H2SO4) solutions is the most widely used process for the extraction of uranium from uranium ores due to the relatively low cost and wide availability of the acid (Bhargava et al., 2015; Gilligan & Nikoloski, 2015). The leach process involves treating ground ore slurry with sulphuric acid at elevated temperatures (typically 60–90 °C) under oxidising conditions in order to convert the uranium in the minerals 2+ from the relatively insoluble tetravalent form (UO2) into water–soluble hexavalent state (UO2), which then complexes with SO42- and forms UO2(SO4)22- in solution. The uranium oxidation is generally carried out in the presence of ferric ion (Fe3+), regardless of the reagent and oxidant used. The most commonly used oxidants for uranium include sodium chlorate, pyrolusite and oxygen (Ring, 1980). These oxidants act indirectly by converting ferrous sulphate, formed by the oxidation reaction of UO2 in slurries, into ferric sulphate. The presence of Fe–containing gangue minerals such as hematite in the ore usually provides sufficient Fe required for the oxidation of UO2. After sulphuric acid leaching, the locked thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) elements are chemically liberated from hematite and uranium mineral grains (Ciobanu, Wade, Cook, Schmidt Mumm, & Giles, 2013). However, the extraction rate of radium (226Ra), lead (210Pb), and polonium (210Po) in sulphate solution is very low due to the limited solubilities of (Ra, Pb, Po)SO4 (Bagnall & Freeman, 1956; Liu & Papangelakis, 2006; Nikitin & Tolmachev, 1933).

Jan 1, 2019

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By G. E. Agar, W. B. Kipkie

"This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady state balance can be calculated for a circuit.Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative tec1nique to arrive at the steady state balance. The program is written so that a variety of circuits can readily be simulated.A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets is presented on sulfide ores, on copper-nickel separation and on silver flotation,"

Jan 1, 1978

By S. Ando

The fatigue crack growth behavior of magnesium single crystal has been investigated, CT (compact tension) type specimens with different notch orientations were prepared. In the case of notch plane and direction are (1-210) and [10-10], fatigue crack propagates parallel to notch, From TEM observation, it is found that pyramial slips occures at the crack tip. When notch is normal to basal plane, a fatigue crack propagates [0001] and parallel to basal plane depending on stress intensity factor range, In the case of notch parallel to basal plane, a fatigue crack propagates through straight route with some {10-12} twin, Fatigue crack growth rate, da/dN of A- and B- specimen is lower than F-specimen with crack parallel to basal plane.

Jan 1, 2004

By Patrik Ericsson

During the 90?s Atlas Copco and LKAB developed a pioneering fully automatic long hole production drilling system based on the Atlas Copco Simba W469 drill rigs. These drill rigs have since then drilled about 8.000.000 drill meters at the LKAB Kiruna and Malmberget mines. In 2005 LKAB ordered three new Atlas Copco Simba W6 C, to complement Simba W469s still in operation. These new Simbas are based on the latest generation computerized drilling technology have proven to meet the expectations of LKAB and now form a base for future automation in Kiruna and Malmberget mines. This paper will present experiences from the introduction of Simba W6 C in LKAB Kiruna and Malmberget mines. The paper will also elaborate on the latest developments in remote access and remote control technology making it a common automation option available for all computerized Atlas Copco drill rigs.

May 1, 2007

By M. A. Stogran-Baker, S. Cole

"Fluorspar mining occurred in the St. Lawrence area from the 1930s until the mid 1980s. In 2013, CFI discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods. A new mill was designed to produce 200,000 tonnes per year of high quality, acid-grade fluorspar concentrate. The simple mill flowsheet includes crushing, dense medium separation (DMS), grinding, sulphide flotation, pulp thickening, fluorite flotation, thickening, and concentrate filtration. The type of flotation cell used is being installed for the first time in North America. Site clearing commenced in the spring of 2016, followed by mill building erection completed by the fall of the same year. Civil and mechanical installation as well as site-wide construction was completed by the end of September 2017. Commissioning commenced, and at the time of paper submission mill production is on track to ramp up to full capacity by the beginning of 2018. This paper will focus on the use of fluorine NMR analysis applied to fluorite and the development of on-stream analysis, flotation cell selection and the decision to install the new cells, and the water control program designed to maintain process control with the least possible environmental impact.HISTORY St. Lawrence is located on the south-eastern coast of the Burin Peninsula in Newfoundland and Labrador. The first occurrence of fluorspar in the St. Lawrence area was recorded in 1843 by British geologist J.B. Jukes (DNR 2010). Fluorspar was likely extracted in small quantities prior, however commercial fluorspar mining did not commence until 1933 at the Black Duck Mine. The Black Duck Mine operation processed ore by washing and screening – acid-grade was hand-picked from the oversize, the undersize was sold as a lower grade product. The Black Duck Mine was closed in 1941 (Wilson 2010). The American Fluorspar Limited (New Fluor) commenced operations on the Director vein in 1936, and was bought by Alcan in 1942 (Cooper 2012). Alcan also developed the Iron Springs as well as the Tarefare deposits. The Black Duck Mine mill had closed, and a new mill was built. This new mill crushed the ore prior to dense medium separation, the sinks of which were sent to Quebec for use in Alcan’s aluminum smelter (CFI 2016). Alcan shut down it’s mining operations in 1977 due to the dropping price of fluorspar as well as labour disputes. In 1986, the British-based Minworth Limited began producing ore from underground at Blue Beach North and Blue Beach South, as well as from open pits at Tarefare and Director veins (Cooper 2012). A new mill was built by Minworth in order to process the ore using flotation to produce an acid-grade concentrate. The low price of fluorspar caused Minworth to shut down operations in 1990. Whilst exploration has been ongoing, no mining had occurred in the area since 1990."

Jan 1, 2018

By G. Shore

Radiation grafted structures my be fabricated to contain ion exchange groups selective to an ion complex. Proper choice of substrate and monomer will provide selective ion exchange with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures have been fabricated to ''capture'' gold, silver and palladium from dilute solutions. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their regenerating solutions are pure metal foil.

Jan 1, 1985

By M. P. Amsden

"Ecstall Mining is a wholly-owned subsidiary of Texas Gulf Sulphur at Timmins, Ontario. The mill tonnage is 10,000 tons per day of two different ores, a copper zinc ore and a silver lead zinc ore, producing about 2400 tons of concentrates per day. These are as a copper concentrate, a high silver zinc concentrate, a low silver zinc concentrate and a silver-lead concentrate. For flotation recovery a very fine grind is required, about 80% minus 325 mesh and the concentrates produced are 40% minus 10 microns.The thickened concentrates are pumped to the filter floor for filtering and drying. The filtering and drying section is separated from the flotation section by a wall and is controlled from a dryer control room by one operator.Two operating panels are located in this control room. One contains stop-start controls for the thickeners, filter motors and vacuum pump motors, and stop-start controls for dryer feed conveyors and dryer product conveyors to concentrate load-out bins, as well as ammeters for conveyor drive motors. Dryer throughput is regulated by Merrick Type L weightometers located on the dryer discharge conveyors and recorded on tons per hour strip charts.The second panel contains the temperature strip charts, furnace drive ammeters, scrubber and exhaust gas controls, burner controls and panel alarms for the four dryers.Filtered concentrates are dried in Nichols-Herreshoff, multiple hearth, dryers consisting of nine hearths (zinc) and seven hearths (copper and lead). There are two dryers for handling zinc concentrates and one each for copper and lead concentrates. The dryers are heated by burning natural gas. Each zinc dryer handles 1,000 t.p.d. and the copper and lead dryers 750 t.p.d. each.Multiple hearth dryers are unusual in the base metal mining industry and the reasons for selecting them in preference to rotary dryers are as follows:1) The concentrates could only be filtered to 15 to 17 percent moisture. These sloppy filter cakes would be extremely difficult to handle in rotary dryers."

Jan 1, 1972

By H. Weissenbaeck, B. Nowak, M. Oesterreicher, R. Stastny

The producers of certain metals like nickel and cobalt increasingly face a shortage of easy-to-mine and easy-to-process ore bodies. Their focus is shifting towards alternative raw materials which in turn demand new, different extraction techniques. One potential route for processing a ferrous ore with a non-ferrous target metal is atmospheric leaching with hydrochloric acid followed by purification of the pregnant leach solution (PLS). For the separation of iron from the PLS, and, in turn, the extraction of the non-ferrous compounds, the following flow sheet is proposed. Pre-concentration of the PLS, oxidation of ferrous (if present) to ferric chloride, hydrolysis of ferric chloride leading to the precipitation of hematite and the evaporation of hydrochloric acid, followed by crystallization of non-hydrolysable metal chlorides by means of sparging hydrogen chloride into the solution. Hydrogen chloride required in the latter step is produced internally by super-azeotropic distillation of regenerated hydrochloric acid. The liquid filtrate from the crystallization step is recycled to hydrolysis. Depending on the specific composition of the PLS, the hematite produced contains only traces of other impurities, whereas the crystallized mix of non-hydrolysable metal chlorides – containing also the target metal in enriched form – contains ferric chloride only in an amount referring to the filter cake moisture. These crystals can then undergo further hydrometallurgical separation and extraction processes. As an example, this flow sheet is proposed for treating nickel laterite ores. Experiments related to the demonstration of crucial assumptions in the flow sheet are presented. Based on those experiments a mass and energy balance of the flow sheet was calculated and is presented here together with a table of the major consumables in order to provide a basis for an operating cost estimate and other process economics.

Jan 1, 2016

By Haibin Wang, Zhiwei Huang, Zhixiang Cui, Wenzhao Cui, Zhi Wang

Fangyuan Two-Step copper smelting process was commercialized in October, 2015 and has been operating for 3 years and 5 months. As the unique continuous copper smelting process with simplified flow in the world, production parameters have been significantly improved after three years. In the first half of 2018, the feed rate was above 200t/h, availability reached 97.5%, operation cost was about 20% lower than the conventional three-step processes showing obvious economic advantages. The Two-Step process in Fangyuan is composed of 1 Submerged Lance Smelting furnace (SLS) and 2 Submerged Lance Converting& Refining furnaces (SLCR). Two SLCRs work alternatively to ensure continuous production. High grade and liquid matte from the SLS is introduced to the SLCR by sealed launder to complete converting and refining. The SLCR is an original and independent innovation of Fangyuan, for which Fangyuan completed lots of development and improvement. This paper will introduce the process and experience. INTRODUCTION China is the largest producer and consumer of refined copper. Most of the processes adopted in China are conventional "Three-Step" copper smelting processes, which are comprised of smelting, converting and refining. There exists some problems in the conventional processes, such as high energy consumption, large heat loss, low altitude emission of SO2, etc. To deal with these problems, Fangyuan developed the new copper smelting process with simplified flow, low cost, clean and high efficiency. The SLCR that combines converting and the refining process was also developed, which shortens the process flow from conventional three steps to two steps. The SLCR is of great significance in promoting the development of the copper industry. Development and industrialization of SLCR At present, copper concentrates are treated in three steps: smelting, converting and refining. Anodes are also produced by continuous converting processes such as the Mitsubishi process and the Double Flash process. Problems like matte transportation by ladle, capacity limitation, and low altitude pollution exist.

Jan 1, 2019

By H. Deveci, E. Y. Yazici, A. D. Bas

The leach solutions of waste of printed circuit boards (WPCB) may contain a wide range of base and precious metals with different concentrations due to heterogeneity of these wastes in composition. Therefore, selection of a suitable metal recovery method is of practical importance for downstream processing of pregnant leach solutions of WPCB. Sulphuric acid leaching of WPCB in the presence of a suitable oxidant is capable of dissolving base metals as well as precious metals such as silver. In this study, cementation of silver from sulphuric acid leach solutions of WPCB using metallic copper, aluminum and zinc was studied. The WPCB sample was assayed to have a silver content of 694 g/t. A synthetic leach solution containing 20 mg/L Ag in sulphuric acid solution (0.51 M H2SO4) was prepared based on the silver concentration in pregnant leach solutions of oxidative sulphuric acid leaching tests. Total sulphate concentration ([SO4 2-]T) was kept constant using sodium sulphate at 1 M. Metallic powders of copper (-850 +600 µm), aluminum (-425 +45 µm) and zinc (-45 µm) were used in the cementation tests. The effects of metal type (Cu, Al or Zn), dosage of metal powders (above the stoichiometric ratio by up to 2000-fold) and temperature (20-80°C) on the rate and extent of silver extraction from the solution was investigated. The effect of presence of copper on the cementation performance was also tested. Under suitable conditions high silver recoveries (>90%) was achieved using metallic copper and zinc while aluminum yielded the lowest silver recovery (i.e. 40% Ag). The kinetics of cementation by zinc was comparatively higher than that of other metals. Increasing the temperature was observed to significantly enhance both the rate and extent of silver cementation. SEM-EDS studies were performed to characterise the metallic powders after cementation.

Jan 1, 2016

By S. A. Beeson, C. Poole

"This paper reports on the development of selective flocculation processes for the direct recovery of KCl values from low-grade Canadian sylvinite and carnallite potash ores.Two reagent suites, consisting of either a non-selective cationic or selective non-ionic flocculant, together with the same selective anionic dispersant, were evaluated. Initial data from component mineral behaviour investigations, reagent adsorption studies and selective flocculation tests on a synthetic potash ore were used in the successful development of processes capable of recovering KCl values without the necessity for desliming to remove water-insolubles.Enhanced multi-stage treatment (involving redispersion and reflocculation) and subsequent floc recovery techniques (including sedimentation, hydrocyclones and froth flotation) were examined, and in all cases the influence of process parameters such as reagent dosages, conditioning times, solids concentration, particle size and other physical design criteria were investigated.The data reported clearly demonstrate the scale-up potential of these processes and possible applications in potash operations."

Jan 1, 2000

By R. Laucournet, E. Billy, M. Joulié

Today Li-ion batteries are considered as one of the most attractive available energy storage solutions. However in order to overcome environmental, legislative and economic issues, the management of used batteries has to be considered and mainly the recycling. The present paper deals with the recycling of used Li-ion batteries and the recovery of high value metals from active materials of electrodes. Lithium nickel cobalt aluminum oxide (NCA) and lithium manganese nickel magnesium oxide (LMNM) cathodes, which contain most of valuable elements typically used in the composition of active materials for Li-ion batteries are investigated by a hydrometallurgy route. The process is divided into two steps: the materials leaching and the elements recovery by a selective chemical separation. Some experimental parameters (acid nature, concentration, time and temperature) are studied to determine the most efficient conditions of dissolution. Then, the valuable elements such as nickel, cobalt and manganese are selectively recovered with a high efficiency close to 100 % and with a high purity by precipitation. By this study, an adaptable hydrometallurgy process can be defined according to the composition of Li-ion batteries to recycle.

Jan 1, 2014

By J. W. Keyes

"The original grinding circuit at East Malartic consisted of two 8 by 8 C.A.C. mills in closed circuit with two 72 inch Akins Classifiers and an 8 by 10 secondary mill in closed circuit with two 48 inch duplex classifiers. With this circuit, we experienced a drastic drop in tonnage from one month to another, due to variations in the hardness of the ore. The first step to overcome this difficulty was made by increasing the critical speeds of the mills from 78% to 82%. This resulted in an increase in the secondary mill throughput; but, when the change was made on the primary mills no increase was obtained.The drastic drops in tonnage were still experienced and through working with Allis Chalmers the 8 by 10 mill was converted to a rod mill and the two 8 by 8 n1ills to secondary mills. This change eliminated the two 72 inch Atkins classifiers and the scoops on all the mills, since the 48 inch Akins classifiers sands could then be fed by gravity to the secondary mills through feed pipes.The rod mill and secondary mill discharges were fed to a common pump box using 5 by 5 S.R.L.'s running at 1085 R.P.M. with a twenty-five foot head. When this was done the pumping costs jumped from $105. 00 for 6 months to $1050. 00 in one month, or from 0. 0004 to 2. 75 cents a ton milled. Several factors contributed to this jump in pumping costs as follows:"

Jan 1, 1964

By O. Rabeau, M. Legault, A. Cheilletz, L. Z. Cheng, J. J. Royer, M. Jébrak

"By compiling geological, structural, geophysical, and geochemical information into a 3D geological model, we evaluated the orogenic gold potential in the vicinity of a hidden segment of an important Archean fault zone, the Cadillac-Larder Lake fault (CLLF) in the region of Rouyn-Noranda. The segment of CLLF in the present study is partly covered by Proterozoic sedimentary rocks. Because more than 2000 t Au have been extracted along the CLLF to date, our objective is to evaluate the gold potential at depth along a poorly known segment of this fault. A 3D geological model (50 km × 9 km × 1.5 km) including the covered segment was built through the compilation and homogenization of available geological data and the construction of 23 cross sections. The geology under the Proterozoic cover was evaluated using geophysical inversions, drill holes (42 in total), and surrounding geology. All available assays were filtered and upscaled to a 250 m × 250 m × 250 m regular cell grid to determine and quantify spatial relationships between geological features and mineralized occurrences using the weights of evidence method. Structural features, such as E-W-trending faults and fault intersections, and certain lithologies with a high primary porosity such as volcanoclastic rocks of the Blake River Group and Timiskaming sedimentary rocks, proved to be very prospective, yielding favourable factors with a weight of evidence index W+ > 0.24. These salient features were then assigned a combination index for ultimately evaluating the orogenic gold potential under the sedimentary cover. The zones resulting in an optimization of exploration targeting were attributed the highest probability, representing ~1% of the initial volume. La compilation des données géologiques, géophysiques, structurales, et géochimiques et leur intégration au sein d’un modèle géologique 3D a permis d’évaluer le potentiel aurifère dans les environs d’une importante zone de faille archéenne sous couverture protérozoïque. Cette méthodologie a été développée en utilisant le cas de la Faille Cadillac-Larder Lake (FCLL) dans la région de Rouyn-Noranda. Puisque plus de 2000 t d’Or ont été extrait à proximité de la FCLL, l’objectifs des travaux est l’évaluation du potentiel aurifère en profondeur de ce segment. Un modèle géologique 3D (50 km × 9 km × 1.5 km) incluant le segment sous couverture de la FCLL a été construit en utilisant l’ensemble des données géologiques disponibles et 23 coupes géologiques. La géologie du socle archéen sous la couverture protérozoïque a été interprétée avec des inversions géophysiques, des forages (42 au total) et les contacts géologiques exposés. Les teneurs aurifères dans le secteur ont été filtrées et ajusté à une grille régulière de 250 m × 250 m × 250 m afin d’évaluer et de quantifier les relations spatiales existantes entre certaines entités géologiques et les emplacements minéralisés en utilisant la méthode du poids de la preuve. Les failles de direction Est-Ouest, les intersections de failles ainsi que certaines lithologies possédant une porosité primaire importantes comme les certains tuf du Groupe de Blake River et les sédiments du Timiskaming se sont montrés très prospectifs avec des valeurs de W+ > 0.24. Ces entités géologiques ont ensuite été utilisées par le biais d’un indice de combinaison pour évaluer le potentiel en or de type orogénique sous le couvert sédimentaire. Cette méthodologie permet une optimisation des campagnes d’exploration puisque les zones pour lesquelles la probabilité de minéralisations a été évaluée à la plus haute valeur représentent 1% du volume initial."

Jan 1, 2009

By Bali. D. D., S. Chattopadhyay

"The planning and construction of prime coking coal beneficiation plants in the nationalized mines in India are reviewed. Flow schemes, construction practice, materials consumption, and costs are detailed.Medium-capacity beneficiation plants with multiple loops are recommended under Indian conditions.IntroductionThe reserve of high-grade and easily washed metallurgical coal in India are quite limited. Prime coking coal constitutes approximately 22% of the total resources and occurs exclusively in the Jharia coalfield in the state of Bihar. Bharat Coking Coal Limited (a subsidiary of Coal India Limited (CIL) the nationalized mining sector of India) owns 80% of the Jharia collieries. The development of Jharia coalfield in the pre-nationalized period before 1971 has been characterized by a large number of small mines with primitive mining methods and low productivity. The production of prime coking coal to meet the demand of the steel industry in India has to increase from the existing level of 11.1 million tonnes to 43.4 million tonnes per annum by 2000 AD, thereby producing 5.61 million tonnes and 22.7 million tonnes of clean coal respectively. An ambitious program has been undertaken for development of bigger mines with an average production of 1 to 3 million tonnes per annum. With the fast dwindling reserves of good quality coking coal, more inferior grade coal seams, having difficult washing characteristics, are now being mined. All the coal from the future mines will have to be beneficiated to make it suitable for consumption of steel plants; the following washeries are being planned for construction by 2000 AD:"

Jan 1, 1986

By A. Morales

Flue dusts from a copper smelting furnace (continuous furnace), have been extensively characterized. The main phases detected have been cuprospinel, anhydrous copper sulfate (chalcocyanite), lead sulfate (anglesite) and arsenic oxides (claudetite and arsenolite). As minor phases, zinc sulfate (zincosite) and several copper or copper/iron sulfides were detected (digenite, anilite, bornite, cubanite), and also a copper oxide (tenorite). The suspension of this material in water leads to the partial dissolution of copper and zinc (chalcocyanite and zincosite) and arsenic oxides. The hydrocyclone classification of the residue makes it possible to obtain two fractions: a copper-rich coarse fraction and an arsenic-rich fine fraction. The coarse fraction can be recycled to the smelting furnace and the fine fraction can be mixed with wastewater sludge from a paper factory, to make both residues inert before disposing them to landfill.

Jan 1, 2007