Search Documents

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By Ian Rozier

"Emphasis in recent years in western Canada has been placed on the development of large open-pit coal mines, the most notable developments being in northeast British Columbia. However, vast resources exist below the limit of economic open-pit mining, and with world demand predictions of the late seventies in mind, the potential of underground coal mining in western Canada has been investigated. Particular emphasis has been placed on the Plains coalfield of Alberta, and there is optimism that underground coal mines will be developed in the Lethbridge area of southern Alberta.With no existing operations in southern Alberta with which to compare mining conditions, any mine planning and feasibility level studies rely heavily on the engineering/geotechnical data obtained from surface investigation to predict ground control problems and technical constraints on mining. Such investigations have been integrated with exploration drilling programs. Emphasis has been placed on extracting maximum information to provide an over-all appreciation of potential ground conditions and to identify specific ground control problems that could be encountered.The acquired geotechnical parameters are then used to evaluate the mine properties from an engineering standpoint for input into the determination of optimum mine layouts, development directions, mining methods and roadway and face support requirements. These geotechnical studies have been primarily directed toward the longwall mining method, but the acquired data base could equally be applied to alternative mining methods.In addition to the lithologic and structural controls which relate to roof stability, caving characteristics, floor heave and subsidence, investigations have been directed at gaining an understanding of the over-all surface and ground water regime with respect to potential inflow into the mine openings and ground control problems that could be caused by inflows encountered during mining. Experience has shown that soft floor conditions and water control are important factors to be considered in a longwall layout, and without doubt these parameters will play a major role in the design and operation of a successful longwall operation in the Lethbridge coalfield."

Jan 1, 1986

By O. Benavente, M. C. Hernández

Selenium is obtained mainly from copper anode slimes, which is a by-product of the copper electrorefining process. Selenium is present in copper anode slimes as silver and copper selenides. Traditionally, selenium has been obtained by pyrometallurgical processes; however, hydrometallurgy has now been incorporated either full or partial to the conventional process. Some hydrometallurgical processes are been developed and used at laboratory level an industrial scale. This document describes theoretical background and results of characterization and dissolution of selenium from a decopperized anode slimes in an alkaline oxidizing system. The results have indicated that the oxidizing leaching process reaches a practically complete dissolution of selenium (up to 90 %); the undissolved portion is due to the generation of a AgCl around the particle surfaces that delays the progression of the reaction. The results indicated that 90% of selenium extraction can be obtained by dissolution under moderate conditions of pH, temperature and reagent concentration in oxidizing medium. INTRODUCTION Selenium is distributed in the earth's crust in most rocks and soils. Selenium is essential, as it has wide range of applications in the medical and food industries as well as, used in semiconductor, sensors and photochemical devices. Selenium is rarely found in the native state, 90% of selenium is obtained from copper anode slimes, which is a byproduct of the copper electrorefining process (Lu, Chang, Yang, & Xie, 2015; Xiao et al., 2017; Yang et al., 2018). In anode slimes, selenium is present as an intermetallic compound, as Ag-Cu selenides. Currently, selenium is recovered from the anode slimes via hydrometallurgical and pyrometallurgical processes (Lu et al., 2015). The traditional pyrometallurgical method recovers selenium effectively, but faces difficulty as a result of increased energy costs and strict environmental regulations associated with the process (Li, Yang, Jin, Chen, & Tong, 2017). Therefore, hydrometallurgical processes are proposed in oxidizing medium such as nitric acid, alkaline leaching with sodium nitrate, wet chlorination and pressure leaching, amongst others (Hait, Jana, & Sanyal, 2012; Kim & Wang, 2010; Xiao et al., 2017; Yang et al., 2018).

Jan 1, 2019

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By D. Q. Li

"This paper briefly introduces problems that can occur in the design of rare earth separation processes and that require close attention during engineering design. Important factors must be considered include the following. 1) The separation process is primarily based on two points. One is the raw material composition and the other is the product purity requirements. 2) Optimization of the rare earth separation process requires optimization of the flowsheet configuration and each process parameter. 3) The separation of heavy rare earths is performed under non-equilibrium conditions. 4) The radioactive elements uranium and thorium must be removed from the feed to separation. 5) Process economy and environmental protection must be considered together in the evaluation of any separation technology options. INTRODUCTIONThe importance of rare earth (RE) is well recognized in high-tech applications and sophisticated national defense technologies. RE is the treasure house of the 21st Century new materials. The RE separation processes developed using HEHEHP (P507), P507-alcohol (ROH) and naphthenic acid (NA) have been widely applied in China. These processes have led to industrial production of all of the individual RE with up to 4N (99.99%) or higher purity (Li, Wan, Lin, Xie, Lin, & Wang, 1980; Li, Wang, & Xie, 1985; Li, 1995; Li, Wang, Meng, & Li, 2005). In order to achieve the best economic and environmental benefits, this paper discusses several problems to which attention must be paid in the design of rare earth separation process."

Jan 1, 2016

By Rui Wang, Engang Wang, En Jiang, Anyuan Deng, Xingwu Zhang, Fei Wang

In this paper, the rectangular strands of Incoloy 800 superalloy were fabricated with a pilot vertical continuous caster in Northeastern University, China. In the processing, an electromagnetic stirring (EMS) is applied on the secondary cooling zone to control the solidifying structure and segregation of elements in the strands. The solidification structure of Incoloy 800 superalloy strands were investigated at different electric parameters and casting parameters. The research results show that the EMS can effectively restrain the dendrite growth and increase the ratio of equiaxed grains in Incoloy 800 superalloy strands as applied a suitable electric parameters and cooling condition in the process of continuous casting. The evolution of dendrite crystallization in Incoloy 800 alloy strands from the surface to its center during the solidifying process was investigated with and without EMS.

Jan 1, 2014

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By N. Molaei, E. R. Bobicki

The continued demand for mineral products, coupled with the depletion of high-grade ore resources, has led to the mining of lower grade ores, which often require fine grinding to achieve mineral liberation. Regrinding of low-grade ores results in the production of fine gangue mineral solids and produces vast quantities of fluid fine tailings which are difficult to separate from water, particularly if they are composed of clay minerals. Organic synthetic polymers and inorganic salts have been widely applied in flocculation of colloidal suspensions in the treatment of mining tailings. However, there are growing concerns regarding their impact on the environment and human health. Recently, extracellular biopolymer flocculants or bioflocculants have attracted much attention as alternative reagents. In this study, much effort has been devoted to considering the effectiveness of protein and polysaccharide-based biopolymers for the dewatering of clay slurries. The interaction between kaolinite and illite clays and biopolymers was investigated via settling tests at pH 7 and 10. Zeta potential measurements were also conducted as a complementary technique. Results showed that protamine and lysozyme protein- based biopolymers were generally the more effective bioflocculants. Pectin, a polysaccharide-based biopolymer, showed a dispersing effect and has the potential to be used as a dispersant and/or depressant for clay minerals in froth flotation. INTRODUCTION With the depletion of high-grade ore resources, the need for mining of low-grade ores has increased over the past few decades (Bourgès-Gastaud, Stoltz, Dolez, Blond, & Touze-Foltz, 2014; Chen, Walshe, Fru, Ciborowski, & Weisener, 2013; C. Wang, Harbottle, Liu, & Xu, 2014). Low-grade ores often require fine grinding and contain clay minerals, leading to the generation of fluid fine tailings (FFT). It is a challenging process to separate suspended clay particles from water (Craciun, Manaila, & Stelescu, 2013; Dompierre, Lindsay, Cruz-Hernández, & Halferdahl, 2016; Kasperski & Mikula, 2011; Mercier et al., 2012). Clay minerals form stable dispersions in water due to their anisotropic nature, non-spherical morphology and colloidal size (Lagaly & Ziesmer, 2003; Olphen, 1977). The difficulty in separating clay minerals from water has led to the accumulation of vast quantities of FFT in oil sands, phosphate, copper and nickel operations, representing a huge liability for mining companies (Chen et al., 2013; Mercier et al., 2012)

Jan 1, 2019

By A. A. Ruitenberg, S. C. Johnson, L. R. Fyffe

"Several types of stratiform and epigenetic gold deposits have been found in New Brunswick, It is the purpose of this paper to describe and classify the epigenetic deposits and demonstrate their relationship to tectonic evolution. The stratiform deposits are mostly volcanogenic massive sulphide deposits that are described elsewhere (Davies et al., 1985).The auriferous epigenetic deposits include quartz-carbonate veins and stockworks, polymetallic veins, contact metasomatic, porphyry copper and volcanic breccia (epithermal) deposits. These epigenetic deposits are concentrated in major fault zones that define or are close to the boundaries of tectonostratigraphic terranes or terranes and cover sequences. The host rocks of the deposits were subjected to extensive crustal thickening resulting from thrusting and/or high angle reverse faulting.The gold deposits north of the Avalon Terrane occur indilatent structures related to mainly dextral wrench faulting that postdated the episode of crustal thickening. The deposits along the southern margin of the Avalon Terrane occur in structures related to late phase thrusting."

Jan 1, 1990

By K. Hashiba, Y. Z. Liang, K. Fukui, M. Koizumi

"Efficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Development and modification of the rock drills based on test data are timeconsuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved. The objective of our research project is to construct a new realistic numerical model of continuous percussive drilling, which is based on the previous Okubo-Nishimatsu’s model. In this study, the parts of the previous model involved in stress wave propagation and attenuation were modified. The two models were prepared for HD712 hydraulic rock drill mounted on crawler drills and HD210 hydraulic rock drill mounted on drilling jumbos. Stress wave propagation was computed with the discretized one-dimensional wave equation. The calculated results were compared to the stress waves measured on a rod during percussive drilling. In both models for HD712 and HD210, the measured stress waves can be reproduced with the one-dimensional model of the same acoustic impedance as the actual piston, shank rod and rod combined with the CI+spring model as a rod joint. The calculated results indicate that the spring constant in the model of a rod joint needs to be set appropriately depending on drilling conditions. INTRODUCTIONEfficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Components related to the percussive drilling are a drill body, a piston, a shank rod, rods, rod joints, a bit and rock. The piston in the drill body is reciprocated by hydraulic pressure and collides with the shank rod a few thousand times per minute. Stress waves generated by the collision propagate and attenuate in the rods and rod joints, and then reach the bit. The bit penetrates and crushes rock. During percussive drilling, the components mutually affect each other and self-induced oscillation occurs. The number of blows and the rate of penetration are determined by the practical drilling conditions such as hydraulic pressure, thrust force, number of rods and mechanical properties of rock. Development and modification of the rock drills based on test data are time-consuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved."

Jan 1, 2015

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"Unique production and environmental problems are associated with multiple seam mining where dragfines are used for overburden and interburden removal. On the production side, the problems are decreased dragfine efficiency in chopdown operations, the general need for spoil rehandle, complications in sequencing stripping and coal handling operations, and potential stability problems in highly stacked spoil. Many variations of dragline methods have been reported in the literature to encounter these problems. Because of the physical properties and peculiar hydrology of sub-arctic region mining of multiple seams in such areas probably could not be done with the methods used in temperate regions.The properties of thawed material would make spoil hard to place in a stable manner and thus would influence the mini sequence. For instance, multiple seam mining which requires some rehandling of spoil and prolonged exposure of overburden and interburden material might be precluded by the instability of thawed spoil and therefore mining techniques have to be modified. Since the deployment and operation of a dragline in modes different from conventional schemes will affect productivity, it will be necessary to study the effects on production of changing the dragfine operational schemes. This paper presents a heuristic simulation model of multi-seam dragline operation of a sub-arctic mine that can be used to analyze the handling of overburden and detailed study of the dragfine performance."

Jan 1, 1986

By Sean Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by using assets more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the ?productivity paradox,? where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the true source of benefits is in how effectively IT is used. Most business sectors have accepted that the reengineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors but unique operational processes. The lessons of changing business practice in more common business processes such as inventory control and customer-supplier relationships can be adequately transposed into a mine. The unique operational processes in mines, in turn require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manger training simulators. This paper reviews the latest IT products and ou lines the processes and kinds of change that will be required in order to benefit from these new investment options.

May 1, 2002

By M. Walmsley, D. Maynard

"This paper describes the use of terrain and soil information in the planning of mine developments, particularly in satisfying many of the existing provincial regulatory requirements. It is also noted that, if properly used, this will provide a solid data base for cost-efficient and environmentally acceptable land use.IntroductionIn planning the development or expansion of a new or existing mine, engineering alternatives are judged on many factors, one of which is the environmental influence. Ecological investigations, ensuring consideration of a rational approach to managing land use and environmental impacts, should be carried out prior to a final decision being made on mine development. The Pit Slope Manual (CANMET, 1976) suggests that both baseline aquatic and terrestrial data be collected and interpreted in such pre-mining surveys. In British Columbia, planning procedures now exist which incorporate biophysical studies to help identify, assess and manage major environmental impacts associated with mine development.Methods outlined in the Guidelines for Coal Development (E.L.U.C., 1976) have been successfully applied in recent years. Following this example, the Inspection and Engineering Division of the B.C. Mineral Resources Branch prepared guidelines to help expedite the development of new base metal mines (Procedures for Obtaining Approval for Metal Mine Development; Ministry of Energy, Mines and PetroleumResources, 1979).The metal-mine guidelines require the proponent of a new mine development project to prepare a two-stage assessment proposal which systematically moves from a preliminary feasibility study (Stage I) to a final project design (Stage II), including application for regulatory approvals. One purpose of the Stage I report is to provide a description of the existing environmental conditions that could be affected by the proposed development. A preliminary environmental impact assessment should also be reported. The Stage II report will contain detailed assessment and management of environmental impacts."

Jan 1, 1981

By Robert Cameron, Colin Ashton, John MacNeil, Leo Piciacchia

"The in pit dam construction and utilities relocation, known as the East Mine Corridor Relocation (EMCR) project, was developed to extend the life of the east side of the Base Mine pit by two veal's. This will result in the recovery of an additional 80 million barrels of oil and delay expenditures associated with the opening of the North Mine by two years. To accomplish this, a large in pit earth structure was required to provide a new embankment foundation for relocating a public highway, four powerlines, a natural gas back-up pipeline, a substation, and a conveyor train. This structure would also he required as a temporary dam 10 contain mature fine tails on the west side until mining is completed in the east mine corridor area, that will then be filled with fluid.The in pit dam, known as The Highway Berm, is 2.5 km long, 63 m high and has 42 million m3 of engineered soil added to the already existing end-dumped soil volumes. To complete the design and construction of a structure of this magnitude, in the very short time frame of two-and-a-half years, presented many new challenges. The main challenges faced were: designing while construction was ongoing; designing without the use of clay cores or sand filters; using relatively non-select overburden material; proper dewatering and base preparation; changing from construction of 50 m high spoil piles to a high specification construction operation; compacting lifts with heavy haulers; constructing during the winter; and monitoring movement of the structure with satellites."

Jan 1, 1995

By P. A. Mascaró, N. Chacon, A. A. Cecchi

"This document shows the development of a system called the “On-line charge level determination in SAG mills” (abbreviated as Jc). The Jc variable has certainly been difficult to measure due to the relevant number of factors and variables that affect the grinding phenomena inside semi autogenous (SAG) mills. To assess the feasibility stage of the proposed system, it was necessary to carry out two tests in different sized SAG mills, 38´ × 22´ and 36´ × 15´, respectively. In each test, the system was configured with a battery of sensors of the following types: (1) strain gauge, (2) accelerometer, and (3) gyroscope. The first step involved for charge level determinations was to determine kidney foot and shoulder by means of a study of the energy-impacts on shell structures. The second step consisted of correlating the measured grinding operational variables with the actual charge levels obtained from SAG mill crash stops. This system development is extremely useful and relevant for providing approximations about mass balances inside SAG mills. It will be a suitable tool for explaining “tonnes per hour” variations and determining optimal points under various operating conditions.INTRODUCTIONThere has been a growing necessity for technologies capable of obtaining “on-line data” of the main comminution variables in order to increase throughput. Computer systems have taken an important role in providing important solutions by means of processing on-line device signals (commonly referred to as monitoring). In semi autogenous (SAG) milling, there are many examples of monitoring devices that allow the operational staff to obtain detailed information both mechanically and electronically inside a grinding circuit. In this context, a new technology has been developed to obtain “Jc total charge (%) online” in two different SAG mills called Vibro-Energy® System.As part of the analysis performed by JKsimMet® the Jb/Jc was estimated because it has an important impact on SAG mill throughput. Different scenarios were simulated and contrasted at various theoretical Jb/Jc values in a baseline circuit (Figure 1)."

Jan 1, 2016

By W. D. Gould, A. Kapoor, K. Morin, P. Bédard

This paper presents the results of a research study that is being conducted by the Mine Effluents Program, Mining and Mineral Science Laboratory (MMSL), Natural Resources Canada aimed at evaluating biotechnology processes for the treatment of nitrogen compounds such as thiocyanide (CNS) and ammonia (NH4-N) which are present in gold mill effluents. A sequencing batch reactor (SBR) technology, commonly used for the biological treatment of municipal and industrial effluents, was used in this study. In the SBR process, the micro-organisms were able to degrade CNS to NH4-N and NH4-N to nitrate (NO3-N) at operating conditions of two 12 h treatment cycles per day, with pH maintained in the 7.4 to 7.6 range, and at room temperature (approximately 21°C) and also at 12 °C. The end products of CNS and NH4-N biological oxidation were NO3-N and sulphate (SO4) that are relatively non-toxic. Partial removal of NO3-N was achieved by biological denitrification reactions in the SBR process. The SBR process effluent was measured to be non-toxic to rainbow trout based on the 96 h acute toxicity test. The microbial consortium isolated from the SBR treating a simulated effluent was able to effectively oxidize CNS and NH4-N to NO3-N in water samples (under batch conditions) collected at three mine sites located in Quebec, the Northwest Territories, and Yukon.

Jan 1, 2004

By Kari Niiranen, Andreas Boehm

LKAB (Luossavaara-Kiirunavaara AB) is operating underground iron ore mine, with three beneficiation and pelletizing plants in Kiruna, Northern Sweden. The wet low intensity magnetic separation (WLIMS) is regarded as the crucial part of silicate mineral separation from the ore. The Kiirunavaara iron ore deposit shows a rather low content of silica (ca. 2.3 to 3.3 % SiO2) but the silica grade is expected to increase in the deeper parts of the deposit. This can be problematic in the case of DR pellet quality with an average silica grade under 0.75 % SiO2. A laboratory scale methodology was developed for the systematic characterization of the ore for mineral processing with the focus on silicates at the Institute of Mineral Processing, University of Leoben. This methodology is combining mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN) was used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and degree of liberation and intergrowth of magnetite and silicates. Based on the mineralogical investigations, actinolite, phlogopite and even quartz and albite are the predominating SiO2 bearing minerals in the ore. The important result of the investigations was the discovery of two separate subtypes within the high silica ore type B2 based on their mineralogy and mineral processing characteristics. The crucial part of the investigations of intergrowths and liberation of magnetite results was the magnetic separation tests carried out with the Davis magnetic tube. The binary intergrowths of magnetite and the silicate minerals (mostly actinolite) are the most common type of mineral association discovered. The significant characteristics in the intergrowths of magnetite and actinolite are the fine-grained magnetite inclusions in actinolite which may end up increasing the SiO2 grade in the magnetite concentrate despite magnetic separation.

Jan 1, 2016

By S. A. Willis

For over 150 years gypsum from Nova Scotia has been shipped via water to the United States east coast. The history of the movement has been one of continual improvements in quarrying, loading, and shipping. At the start, man-size rock quarried by hand auger and black powder was loaded into horse-drawn carts, hauled to the waterfront, and dumped into 100-ton sailing schooners. Last year the Canadian Gypsum Company completed the latest and most modern of these successive installations for the movement of this Nova Scotia product. The new system loads crushed gypsum into 11,600-ton vessels at Hantsport in two hours' time at high tide. At the head of the bay of Fundy are located vast deposits of gypsum. The tidal rise and fall of 45 feet twice a day, with its attendant swift currents, has always presented major navigation and shipping problems. When the tide is low, the Hantsport ship-loading pier is high and dry, with no water within 400 feet. Three hours later a large river has flooded in (running up hill) and large steamers can dock at the wharf. Before high water, the ship has been loaded and -there is a depth of 30 feet or more of water around the wharf. At high water, the ship sails away on the ebbing tide as the river runs in the other direction. Tides are caused by the gravitational attraction of the moon and sun on the ocean. When both celestial bodies are pulling together the 'spring tide' results, which means a 50-foot variation from high to low. This occurs at new and full moon. A week later, when the sun and moon work in opposition, the difference is only 32 feet between high and low water. The bay of Fundy, having a funnel shape (150 miles wide at mouth from Yarmouth to Portland, while the upper estuary at Hantsport is only one mile wide), builds up a tidal influence from 10 feet at the mouth to an average of 45 feet at Hantsport.

Jan 1, 1948

By V. Cvetkovic, L. Zou, L. Jing

"Sorption process plays a significant role for solute retardation in rock fractures. In this paper, for the aim to investigate the effect of sorption on solute transport in a single rough fracture, a 2D model of representative single rock fracture was built and its roughness was statistically characterized based on the measured data of rock surface topography by laser scanning. A Finite Volume Method (FVM) code was developed to solve the Navier-Stokes (NS) equations and transport equation for numerical modelling the process of fluid flow and solute transport in the rock fracture model. Two groups of simulations were conducted: with and without the consideration of the sorption process with different average flow velocities. The results show that the surface roughness increased the complexities of flow fields, and the non-linear sorption process plays a significant role in the retardation of solute transport through rock fractures. The sorption process caused an obvious lagging time in both the solute concentration fields (plumes) and corresponding breakthrough curves. This lagging time increases with the distance from the inlet boundary, and relatively decreases with the increase of mean velocities. INTRODUCTIONFluid flow and solute transport in fractured rocks is an important research topic for performance and risk assessments for rock engineering projects concerning geo-environment safety, such as radioactive waste disposal, mining, geothermal extraction, reservoir engineering and other contaminant transport processes in geosphere (Berkowitz 2002).The solute transport in the rock fractures mainly involve the advection, surface sorption, matrix diffusion, dispersion, radioactive decay and chemical reactions, governed by general transport equations (e.g. Bodin et al., 2003). Among these transport phenomena, the sorption on the fracture walls can alter solute migration between the fractures, and play an important role in natural retention of solute transport (Weber et al., 1991; Wels et al., 1998; Kumar 2007; Dai et al., 2012). The aim of this study is to investigate the effect of sorption on the solute transport in a single rock fracture with rough surfaces. More complex transport processes, such as matrix diffusion, dispersions, radioactive decay and chemical reactions, are not included in this study."

Jan 1, 2015