Search Documents

By M. D. Lawton, P. Steen

"Drilling results from the established levels at AngloRouyn Mines Limited had indicated inadequate tonnages to meet the planning schedule. It was decided to develop the main zone of the orebody below the bottom working level of the mine. The orebody dips north at an average of 50 degrees and plunges to the west at about 10 degrees. Due to the need for rapid development of this area, a decision was made to use trackless equipment.This paper describes the method used and highlights the use of small 5-ton diesel trucks as carriers for the 2-cu.yd LHD machine. The method achieved advances of about 1,000 feet per month, at a dip of 12 degrees over a length of close to 2,000 feet, using as few as 20 men per day."

Jan 1, 1971

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as 'soapstone'. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By T. K. Akopyan, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"A qualitative and quantitative analysis of the new Al-Ca-Mn-Fe phase diagram in the region of the aluminium corner is carried out using both thermodynamic calculations and experimental methods. Using the obtained data, the principal possibility of creating both cast and wrought sparingly alloyed aluminium alloys with calcium, manganese, scandium and zirconium at allowable iron contents of up to 0.4% that do not require solution treatment and quenching is justified. At the selected concentrations, the entire amount of manganese (1%) is practically included in the aluminium matrix, while calcium (~2%) and iron are in the multiphase eutectic, which has a fine structure. The joint introduction of 0.25% Zr and 0.1% Sc into the alloy leads to precipitation hardening due to the formation of the L12-Al3(Zr,Sc) phase during annealing. Based on the experimental data for the model multicomponent Al2CaMnFeZrSc alloy, it is shown that such alloys can combine high mechanical properties and good manufacturability during both casting and metal forming. This is due to the combination of a narrow temperature range of solidification with a fine eutectic structure.INTRODUCTION Hardening in branded aluminium alloys (both cast and wrought) is generally achieved by heat treatment of the T6 type, including quenching and artificial aging (Zolotorevskiy, 2007; Kaufman, 2004; Mondolfo, 1976). Heat treatment significantly increases the cost of the final products. Therefore, industrial companies are interested in developing alloys that can be hardened to the desired level without quenching. To solve this problem, alloys with scandium are the most suitable (Toropova, 1998; RØyset, 2005). This element (usually in an amount of ~0.3%) is one of the most effective hardeners in aluminium alloys, due to the formation of Al3Sc (L12) phase secondary precipitates, the size of which is less than 10 nm (Knipling, 2010; Fuller, 2005). These nanoparticles are formed during the annealing via decomposition of the supersaturated aluminium solid solution (hereinafter referred to as (Al)). This feature allows us to significantly increase the strength of aluminium alloys by simple annealing (at ~300°C), i.e., without heat treatment, including quenching. However, scandium is a very expensive metal, so its use as an additive is severely limited. The most effective method is the introduction of scandium together with zirconium (Lefebvre, 2009; Booth-Morrison, 2012). The optimal combination is the introduction of ~0.1% Sc together with 0.20–0.25% Zr, which, according to (Belov, 2006), gives approximately the same strengthening effect as the introduction of 0.3% Sc."

Jan 1, 2018

By David A. Edgecombre

This paper discusses modern practices in the extrusion of steel. Particular emphasis is given to a description of the Ugine Sejournet method of extrusion, involving the use of glass as a hot work lubricant. Other methods are also mentioned. A brief history of extrusion is presented; present practices in the quality extrusion of tubing and solids are described; and the future potentials of the) process as a tonnage producer are briefly discussed. The advantages of extrusion and the reasons for the use of a glass lubricant, as well as the various methods of using glass, are given. The process, as described, is being used in the manufacture of large commercial quantities of stainless steel tubing and sections. This extrusion process is an essential and unique means of forming such atomic-age materials as titanium, zirconium, molybdenum and other super alloys all of which are materials required in the creation of nuclear installations.

Jan 1, 1963

By The Staff

"THE property of Red Mountain Mines Limited is located 11/2 miles north and west of the town of Rossland, in southern British Columbia. The mine is situated on the flank of Red mountain, famous in pioneer days as the site of a number of profitable gold-copper producers. Mining and milling commenced in May, 1966, and by the first of July the concentrator was treating close to its average design capacity of 400 tons per day. The following description of the property and its operations is divided into three parts, dealing respectively with geology, mining and milling.GeologyAll the known ore reserves of Red Mountain Mines occur on the Coxey claim, on the west slope of Red mountain. Although there are indications of molybdenite mineralization elsewhere on the Company's property, these have not been developed.The Coxey and adjoining areas are underlain by the Mount Roberts formation of the Rossland volca-nics. This formation consists of an interbedded series of volcanic and sedimentary rocks, mostly brecciated and silicified near the ore zone, and all intruded by igneous rocks which occur in various forms, and vary in composition from basic to acid. The country rock in the vicinity of the mineralization seems to be mostly a volcanic, approximately andesitic in composition, and possibly a surface flow. There is much banding, some of which is undoubtedly due to tuff and agglomerate layers, and some to narrow, siliceous, sedimentary horizons such as the surface exposure of the main ""A"" orebody, much of which was a thin capping of greyish banded rock that looked like quartzite. The drill holes also intersected occasional layers of black, argillaceous quartzite, sometimes altered to a greenish colour. The whole assemblage has been silicified with varied intensity, sometimes to such an extent as to have obscured or obliterated the original characteristics. The mineralized zone has also been strongly brecciated, the fragments varying in size from less than an inch up to large masses, best described as a mega-breccia. Anomalous results obtained in drilling, such as sedimentary sections that do not appear in adjoining holes, may sometimes be due to the presence of these large blocks, no longer in their original position. The whole volcanic unit is thus very complex and confusing. For practical purposes, the ore may be said to occur in a greenstone formation with minor sedimentary interbeds and considerable later igneous material."

Jan 1, 1967

By W. A. Green

Introduction While pilot-mill operations were being carried on at Flin Flon, as described by R. E. Phelan (1), a detailed topographic map was being made of the area in the vicinity of the ore-body for later use in laying out plans for the final plant. The area covered by this survey was 6,600 feet by 6,600 feet, with contours on 2-foot intervals. As mentioned by Mr. Phelan, it was definitely decided at the end of November, 1927, to take up the option on the Flin Flon property and to proceed immediately with the plans for construction of a metallurgical plant at Flin Flon to treat 3,000 tons of ore per day, and of a hydro-electric power plant at Island Falls, Saskatchewan, to supply power for the future operations at Flin Flon. Railway Built From The Pas to Flin Flon Just as soon as the decision was made to go ahead with the construction work and opening-up of the property, it was of course essential to give immediate attention to the building of a railway to the mine. Many years previously, a preliminary survey had been made for a railway to branch off the Hudson Bay railway at a point 4.7 miles northeast of The Pas, and, during certain negotiations in 1925, the Provincial Government of Manitoba had agreed to guarantee the railway bonds necessary to finance the building of the line, so that it was possible to organize for this work immediately. A contract was let by the newly organized Manitoba Northern Railway Company to the Dominion Construction Company, Ltd., and Tomlinson, for the building of the railway to the mine, a distance of approximately 87 miles (see Figure 1). The Manitoba Northern railway is a subsidiary to the Canadian National railway, and all engineering and supervision of the contractors was done by the Canadian National engineers. Actual construction work was started in January, 1928. The first 52 miles of the railway from The Pas to Cranberry Portage is over fairly level, although slightly rolling, country, and a considerable portion of the route is over muskeg area. Rails were laid on top of the frozen muskegs. Gravel deposits were opened-up along the line and, before warm weather; sufficient ballast .was distributed in the muskeg areas to prevent thawing under the track, and thus give the necessary support to allow uninterrupted transportation over the line.

Jan 1, 1935

By Diego L. Romero, Joy P. Romero

"IntroductionThe purpose of this paper is to explain the theory and demonstrate the industrial applications of electrostatic separation. Wabush Mines' use of this type of processing for the concentration of iron ore is unique in the industry. Other minerals are concentrated electrostatically but the process is not widely used.Typical minerals separated by electrostatic separation techniques are:Non-ConductorsAnhydriteApatiteBariteBastnasiteBerylCalciteChrysotileCorundumDiamondEpidoteFeldsparsFluoriteGarnetGypsumHornblendeKyaniteAcmiteAugiteBrookiteCassiteriteChalcopyriteChromiteColumbiteCopperDaviditeEuxeniteFerberiteFrankliniteGalenaGoldGraphiteHematiteMica (Biotite)Mica (Muscovite)MonaziteOlivinePerovskiteQuartzScheeliteSideriteSillimaniteSpheneStauroliteSulphurTopazTourmalineXenotimeZirconConductorsIlmeniteIlmenite-( High Iron)IlvaiteKoppiteMagnetiteMarmatiteMolybdenitePyriteRutileSamarskiteSphaleriteTantaliteWolframiteWulfeniteThe limitations of this process are:1. There must be a difference in conductivity between the minerals being separated.2. The size range must not be very wide.3. The specific gravity of minerals being separated should be similar or the minerals to be pinned should be lighter. 4. The feed must be dry.5. The particle shape should be more or less uniform. 6. The feed must not be high in true middling particles."

Jan 1, 1989

By Cristina Echavarría

MAIN POINTS ? The region: opportunities and limitations ? Overview of main issues emerging from MMSD in South America ? Who comprises the local community? ? What are the main challenges? ? Some suggestions for companies to improve their contribution to local sustainable development of mineral rich localities THE REGIONAL CONTEXT 1. The region is a producer of minerals contributing over 20% to world metal production. It consumes only 8% 2. Significant diversity of national contexts-both between countries and within countries 3. Variable but predominant need for strengthening of government and community institutions and governance, especially at the local level 4. Dearth of baseline information for decision making 5. Sustained social spending during early 90?s as a consequence of economic recovery and fiscal policy, produced important advances in education and health 6. Despite government efforts in most countries poverty continues growing 7. Highly inequitable distribution of wealth persists

May 1, 2002

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By E. A. Roux

As the first mine-to-metal zinc operation utilising atmospheric leaching, solvent extraction and electrowinning, Skorpion Zinc faces unique challenges and opportunities. One of these challenges is found in the solvent extraction circuit, in which di-ethylhexyl phosphoric acid (D2EHPA) is used as the organic extractant. Although D2EHPA is an excellent extractant for zinc, it suffers from the co-extraction of ferric iron, which is produced during leaching and by the corrosion of the grinding media. This situation is partially mitigated by iron precipitation in the neutralisation step prior to solvent extraction. Unfortunately, some ferric iron still reports to the solvent extraction process. This leads to a slow build up of iron in the organic phase. Chemical stripping is used to maintain the Fe concentration at an acceptable level. In this paper, the efficiency of the iron removal process is discussed.

Jan 1, 2006

By W. F. Scott, K. L. Somerville

"This paper outlines the development and inplementation of functional training at the Thompson Mine of Inco Metals Company, Manitoba Division. This training is an extension of similar methods implemented throughout the company to meet safety and health and productivity objectives. It consists of the orientation to the mine, induction in the basic mining skills, and specific training in drilling and other skills in the mine. Initial results indicated a positive effect on the safety performance and proficiency of the mine workforce.IntroductionThe primary mining method at the Thompson Mine is mechanized cut and fill, with secondary recovery of pillars by undercut and fill . These methods require a workforce of about 900 hourly operating employees to obtain capacity production of 6500 tons of ore per day.Historically, turnover of mine employees has been high and large numbers of new recruits are introduced to the mine every year. These men are recruited primarily in Manitoba, but also from distant areas of Canada; most of the se people have no previous mining experience.Training has always been an important component of mine operations. Mine supervisors and experienced miners have committed an appreciable amount of time and effort to training these new recruits. As well, training efforts have been directed toward upgrading the skills of experienced workers.Recently, a growing awareness of the significance of this training effort and its impact on accident frequency, productivity, turnover and other important parameters of the mine operation has led to a review of training methods. The training program described in this paper has resulted from this review."

Jan 1, 1981

By B. Voyzelle

The deterioration of highway and bridge infrastructure has received considerable attention in recent years because of the billions of dollars needed for repair and rehabilitation. A major factor contributing to this problem is the corrosion of steel reinforcement. Reinforcing steels with good corrosion resistance and relatively low price are therefore essential for maintenance, cost reduction and service-life extension of the steel-reinforced structures. This article describes the development of low-alloying steels that offers good corrosion resistance with reasonably low cost. Topics include steel microstructures, mechanical properties, corrosion performance, industrial applications and economic aspects.

Jan 1, 2005

By B. L. Moreau

Certain gas wells tend to form hydrates in the production tubing. This paper outlines a method developed and used by the Author's company to overcome the problem. The injection of glycol to control hydrates results in sufficient dehydration to allow the gas to be trans-ported through a field-gathering system b a treatment plant. Sub-surface injection of glycol also offers a method of introducing corrosion inhibitors into the gas stream. The major operating difficulties have been overcome and the system is now in use in the northeastern part of British Columbia.

Jan 1, 1958

By P. D. Waters

"Mineral deposits are where you find them; they have no allegiance to territorial boundaries. Over the past decade much of the new investment in mining has been outside of continental North America, let alone Canada. The larger Canadian Banks have pursued this offshore business through their multi-national organizations; this reflects both the increasingly international orientation of today's business environment, and to a degree, the competitive advantage of these offshore developments.The current oversupply situation in mineral markets and the increasing maturity of the Developed World Economy reduces the need for new mining projects relative to growth' in GNP. Those that are brought on stream in the future due to their competitive advantage, will continue to be pursued by lenders and equity investors alike. IntroductionProspects facing those who search for mineral wealth were described rather well more than 200 years ago by a Scottish professor of moral philosophy, who also happens to be the father of modern economics.In search for new mines, Adam Smith wrote in The Wealth of Nations, ""there seems to be no certain limits either to the possible success or to the possible disappointment of human industry"".How true that statement remains today, where we are seeing economic cyclical problems compounded by basic fundamental structural change within the mining industry.Despite the enormous advances in earth sciences during the past two centuries, the rewards of mineral exploration still remain uncertain. Even though a promising orebody is found, ultimate profitability may still depend on the vagaries of the marketplace, where large and unanticipated changes in supply, demand and prices can play havoc with the best of calculations.The Canadian mining industry has had its share of disappointment during the past few years, with savage competition, shrinking demand, declining prices, and disappearing profits. But it has also had some share of success, such as at Hernlo, which now seems certain to provide some of the lowest cost gold production in the world"

Jan 1, 1986

By Milton C. Graves, Marcos Zentilli

"Gold has been reported from most geological environments in Nova Scotia; however, virtually all production (circa 2,000, 000 troy ounces; circa 60 tonnes) has come from that part of the province to the south of the Glooscap Fault which is underlain by Lower Paleozoic rocks of the Meguma Group. Over fifty concordant sets of quartz-carbonate-arsenopyrite veins have seen production. The host rocks are greenschist-grade equivalents of Cambro-Ordovician flyschoid quartz wackes and shales folded and metamorphosed during the Devonian Acadian Orogeny. The veins were emplaced under conditions of greenschist-grade regional metamorphism and under the same conditions of tectonic stress that later resulted in the regional folds and penetrative, axial-plane slaty cleavage. Rapid filling of hydraulic fractures caused by excess metamorphic pore fluid pressure under Acadian tectonic stress conditions can account for the geometry and paragenesis of these veins.The ultimate source for gold deposits in most greenschist-grade domains remains in doubt, but these domains seem to have had ample gold within them available for mobilization. The work done, to date, on the gold geology of Nova Scotia suggests that regional greenschist metamorphism was an effective mobilizer and a potential concentrator of Au, As, W, Fe and S from these vast reservoirs.In rocks of pre-Acadian age north of the Glooscap Fault, gold occurs as an important accessory in volcanogenic massive sulphide ore, as a minor constituent in other types of basemetal concentrations and in one small concordant group of quartz veins.The post-Acadian metallogenetic domain, which overlies and overprints the two older domains, contains small amounts of gold in many mineralizing environments. Veins, with stibnite and gold, cross-cut crystalline rocks. Disseminated gold is present in basal conglomerates of post-tectonic molasse. Gold has been a by-product of Mississippi Valley-type Pb-Zn-Ba-Sr deposits in Lower Carboniferous sedimentary rocks and has been reported with Pb-Zn-Ba-F in veins which cross-cut Lower Carboniferous and older rocks. Small post-glacial placers have also seen minor production."

Jan 1, 1982

By Z. Jun, L. Kerning

Jinlong copper smelter and refinery, originally designed for 100,000tpa primary copper and started up in 1997, has been expanding its capacity on the basis of operational optimization and by modifying its facilities. Currently it is producing 210,000tpa primary copper, and the new phase of expansion project with a target capacity of 350,000tpa primary copper is ongoing. This paper reviews problems and improvements made with operation and equipment in the past years. Recent plant operation is briefly described. The expansion projects completed are summarized and the ongoing expansion project is present.

Jan 1, 2007

By C. G. McLachlan

INTRODUCTION The work described in the following paper was under-taken with a view to determining, if possible, the relative importance of some of the phenomena on which flotation seems to depend, in the hope that, if this information could be obtained, it would be of value in dealing with the problem as a whole. At the outset, brief reference will be made to three papers which had a considerable bearing on the course followed in the present investigation. In 1919, Langmuir, in a paper on 'The Mechanism of the Surface Phenomena of Flotation', showed that mono-molecular films of very great stability could be produced on solid surfaces with oleic acid, but that pure paraffin oil, though spreading readily on a dean dry surface, was easily displaced by water.

Jan 1, 1926

By W. Torres Pino, L. Mariscal Samaniego

The Ilo Smelter has been continuously operating since 1960 with Reverberatory furnaces and Pierce Smith converters producing blister copper. The original installed capacity of 1.134 tons per day of concentrated was expanded in 1976. A process of modernization started in 1995 and 1998 with the installation of an El Teniente Converter, a sulfuric acid plant and an oxygen plant to reduce the gaseous emissions to the atmosphere. With the official approval of the Environmental Compliance and Management Program (Programa de Adecuaci6n y Manejo Ambiental - PAMA) in January 1997, Southern Peru Copper Corporation made a commitment to capture 91. 7% of the S02 generated at the smelter by January 2007. After an evaluation of six different technologies, the ISASMEL T process was selected because it can be easily adapted to the present operation, has a lower capital cost and it is a simple process. The fast learning curve to reach the total capacity will allow to fulfill the PAMA commitment in time. The project construction is in process and SPCC is prepared for a successful start-up and transition of the current operations at the end of year 2006. This paper outlines the factors considered by SPCC in its choice of ISASMEL T technology and describes the construction and the start-up activities of the new facilities.

Jan 1, 2007

By D. Harrington

Ventilation of underground workings consists in establishment of such control of air currents that the underground workers may work in safety, with maximum comfort and efficiency, and without impairment of health; and requires that the mine openings may be made subject to such control of air flow as to remove from these workings at ordinary times harmful gases and dusts, and that, at time of emergency, such as fire or explosion, there may be maintained as much or as little air flow as may be desired covering portions of the mine or the mine in its entirety. Control of air flow is the keystone of any ventilating structure, and this very essential feature is obtainable only by the installation of mechanically-operated fans, together with other;. ventilating devices such as doors, over-casts, regulators, etc. Every mine, large or small, coal or metal, should from the outset be equipped with a fan. While much has been written about natural ventilation and many claims made that in specific mines there is sufficient natural air flow, there are few if any mines, coal or metal, where natural ventilation supplies anything like adequately safe or healthful conditions for underground workers even at ordinary times; and at a time of mine fire or explosion, mines depending upon natural ventilation are practically helpless, and certainly are decidedly dangerous to those unfortunates forced to be in them. While ventilation has practically always been deemed an integral part of coal mining, metal mines have rarely paid much, if any, attention to air circulation until forced to do so by occurrence of some untoward condition or accident. Yet metal mines actually have as great need of efficient circulation of air as have coal mines. The coal mine must remove the dangerous explosive gas, methane, also fumes from explosives and, in occasional places, other gases such as carbon dioxide or nitrogen.

Jan 1, 1933

By W. Pietsch

For a number of reasons, solids entering and leaving facilities for the treatment of minerals are becoming increasingly finer. Such materials pose problems throughout processing. Solids featuring small particle sizes tend to dusting, result in losses and segregation, exhibit various storage, transportation, and metering problems, and fine particulate effluents can not be easily captured, used and/or recycled. Sustainable mineral processing must minimize the exploitation of natural resources and avoid the need for disposal of wastes. The first requires the use of lower quality raw materials and upgrading, which typically results in the production of fine grained concentrates, and the latter encourages the recycling of wastes and byproducts or efforts to investigate them as sources for secondary raw materials or other beneficial applications. To overcome the difficulties associated with fine particulate solids, size enlargement by agglomeration is necessary. The resulting products have free flow characteristics, do no longer dust or segregate, and are sized and shaped as required for optimum processing. In addition, agglomerated materials may be engineered to feature desirable structure, composition, and a number of related, improved properties. Such engineering may be applied for the modification of fine run-of-mine and up-graded minerals as well as the production of secondary raw materials from by-products or wastes. By the interdisciplinary application of size enlargement by agglomeration waste-free processing of minerals becomes feasible.

Jan 1, 2004