Search Documents

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel/truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By Robert B. Parsons

"The 1994 Quebec Budget included a significant overhaul of the mining duties sys-tem in that province: broadening the base and lowering the rate, all in the name of “ensuring the integrity of the taxation system"" and ""enabling the State to collect fair compensation "". The reforms hit hardest on the small, lightly-capitalized producer, by repealing the basic annual exemption, limiting the refund for losses, and significantly reducing the investment and processing allowances. There is some relief provided in the form of faster depreciation rates and a lower nominal tax rate, but the thrust of the overhaul is clear -higher taxes on the mining sector.IntroductionAlthough Quebec's mining tax regime represents under 10J0 of the province's revenue base, and was significantly reformed in 1979 and 1985, the May 13, 1994, provincial budget introduced further significant changes to the Mining Duties Act, The hope (on the part of the province) is to reduce the provincial ""subsidy"" for mining by $20 mil· lion per year by 1996."

Jan 1, 1995

By C. Okay Aksoy

In Turkey, the increasing demand for lignite has necessitated an increased emphasis on both lignite production and recovery. This emphasis has resulted in a gradual increase in the application of the retreat longwall mining method for both its product recovery and productivity benefits. Also, in order to maximize the recovery of the natural resources and to increase total production, it is necessary to take advantage of underground reserve before abandoning the mine. This means that at the end of the life of the mine, the main drift safety pillar and the shaft pillar will generally be extracted. This investigation a preliminary study of the stability of the main drift and the shaft at the Hustas Mine as the safety pillars are extracted. In this study, field surveys belonging to the underground colliery of Hustas Co. in Soma have been investigated with the help of LAMODEL working under the Laminated Displacement Discontinuity principle for the models calibrated as a results of physical model and finite element analyses. The convenience of Laminated Displacement Discontinuity Analysis has been researched in such studies. The results out of the models have been coherent with the previous studies.

May 1, 2004

By C. O. Aksoy

"Pillars left to ensure the stability of major underground coal mine infrastructure (shafts, drifts) often contain substantial quantities of coal. Recovery of this coal is an efficient use of the resource, but often presents safety hazards; pillar extraction destabilizes the protected structure, and can make its use dangerous. In this study, the stability of an active shaft at an underground coal mine situated in the Soma- Manisa region of Turkey was investigated during the recovery of the coal in the shaft safety pillar.A proprietary three-dimensional finite element analysis model (ANSYS) was used. An elastic-plastic material model utilizing the Drucker-Prager failure criterion was employed. The three-dimensional Drucker-Prager formulation was preferred over the two-dimensional Mohr-Coulomb model because it was thought to more accurately represent the strain hardening behaviour shown by most geologic materials.Stresses and deformations formed around the shaft support were estimated using the model and the results were verified by in situ observations. The results show that stress distributions around the shaft and the subsidence of the shaft support are influenced by the location location of the extraction front and the break angle of the overlying material."

Jan 1, 2005

By C. H. Ash

"Abstract-The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of western Canada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits. The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bornite± magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprise quartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite is the main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+ carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)], contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite composition which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By C. H. Ash

"The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of westernCanada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits.The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bor-nite±magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprisequartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite isthe main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)],contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite com-position which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By Vern Evans

Saskatchewan has historically been recognized for farming, but in 1943 while drilling for oil, potash was discovered. The initial attempt to gain access to the potash beds was unsuccessful, however, subsequent attempts were successful and today there are ten operating potash mines in Saskatchewan. In this paper we will provide a brief overview of the historical and current Potash industry in Saskatchewan.

May 1, 2011

By C. Poon

For slope stability, knowledge of major and minor discontinuity sets that form the rock mass fabric is paramount for pit slope designs. Due to the increased awareness of health and safety in mining projects, efforts have been made to limit structural mapping in order to minimize the risk to personnel associated with approaching potentially unstable areas. Recognizing the importance of such safety precautions, Golder Associates Ltd. is applying a combination of techniques including 3D photogrammetry, conventional mapping and drilling with core orientation to enhance structural data collection. Photogrammetry uses digital photographs to produce a virtual model of a rock mass surface. The application of these techniques will be exemplified through an expansion design of an existing open pit. A comparison of stereonets obtained using these techniques showed some agreements, but also highlighted limitations of each method. The application of photogrammetry was found to be very useful in complementing the other existing techniques.

May 1, 2009

By Josée Dartois

En 1988, à l?instar de plusieurs états du monde industrialisé, le Québec décidait d?accélérer la cadence de l?assainissement des rejets industriels et lançait un programme intégré de réduction de la pollution industrielle visant, à la fois, les rejets dans le milieu aquatique, les émissions atmosphériques et les matières résiduelles. Ce programme fut intitulé le Programme de réduction des rejets industriels.

Nov 1, 2002

By John Hughes

1. De Beers, Diamonds and Canada 1.1. De Beers was founded long ago (1888, the same time that Canada became a country) in a rural mining village in South Africa. Today, we employ 22,000 people across 19 countries and have 14 mines including open pits, shafts, beach-sands and seabed. 1.2. Last year our sales were US$5.7 billion and our total production amounted to 47 million carats which means a 40% global market share. For the Kyoto buffs in the audience, the company consumes 66 million cubic metres of water per annum, 210 million litres of hydrocarbon fuel and 1,600 GWh of electricity. Stats are good, but aren?t as expressive as a movie. This one is 2 minutes long, which is quicker than I could elaborate. (Video 1 - 2 minutes) 2. De Beers in Botswana is the leading source of diamonds 2.1 Today Botswana is the Jewell in the Crown. There are three big open pits that enjoy economies of scale that make them the lowest cost producers. Last year 60 million tonnes of overburden and 30 million tonnes of ore were moved in Botswana alone. Botswana produced 31 million carats, compared to 14 million carats in South Africa and 2 million very high quality carats inn Namibia. 3. Diamond Mines provide feedstock? ?.to jewellery stores

Apr 1, 2005

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By Q. Han

Irradiation of high energy ultrasonic vibration in metals and alloys generates oscillating strain and stress fields in solids, and introduces nonlinear effects such as cavitation, acoustic streaming, and radiation pressure in molten materials. These nonlinear effects can be utilized to assist conventional material processing processes. This article describes recent research at Oak Ridge National Labs (ORNL) and Purdue University on using high intensity ultrasonic vibrations for degassing molten aluminum, processing particulate reinforced metal matrix composites, refining metals and alloys during solidification process, welding, and producing bulk nanostructures in solid metals and alloys.

Jan 1, 2014

By Masaharu Moteki

At present, the Unmanned Construction System (UCS) is adapted on initial operation against the disaster. For instance, it has been used in Unzen. When the scale of the disaster is big, or the danger to a person is big, the UCS is expected as a quick and safe construction technology. The Remote Controlled UCS is introduced into construction site to repair earth-fill embankment or to remove rock, as urgent measures after the disaster outbreak. For improvement of the operability, shortening of the skill time, reduction of the fatigue, examination of the most suitable system (placement of a monitor and the joy stick) of the remote system is a main theme in the Public Works Research Institute (PWRI). In the report of this year, when the operator controls construction machine directly or he controls it using remote system (he can check the situation of site only via monitor), the degree of achievement, construction efficiency and construction precision were inspected. The remote system which is based on the system used at Unzen was developed at PWRI.

Aug 1, 2013

By R. A. Triglavcanin

Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ? all of these need to occur in the right order and in the right proportions within the thickener feedwell, the secret to thickener performance.

May 1, 2009

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By D. B. Langford, R. Hart

"This paper presents an overview of the state-of-the-art in industrial and utility power metering and control systems with particular emphasis on Digital Power Meters and Power Demand Controllers.IntroductionModern micro-processor technology, combined with very fast, high accuracy analog to digital converters, is rapidly allowing economical, digital power instrumentation systems to replace the traditional electro-mechanical meters and equipment previously used for instrumentation, control and protection in industrial power systems. Consequently, instrumentation and Supervisory, Control and Data Acquisition (SCADA) systems that were only practical for the very large utility or user are now available to smaller utilities and users. The information available includes sequence of event recording, trend logging, energy management cost allocation and automated load control, among others. The heart of any power monitoring system is the Digital Instrumentation Package (DIP) . These ""DIP's"" include Digital Power Meters (DPM's) and Power Demand Controllers (PDC's) as well as other specialized instrumentation packages such as Mini RTU's."

Jan 1, 1991

By Trang T. Tran-Valade

With continually increasing energy prices, the mining industry has been on the search for new energy optimization technologies. One area that is garnering great interest is Ventilation-On-Demand (VOD). Prior to selection and implementation of a VOD solution, it is important to fully understand the mine requirements as well as its existing infrastructure and the interaction with other automation in place at the site. With this information, a business case can be generated including a cost versus benefit comparison for various control strategies. To assist in the development of the business case, this paper will identify key areas for consideration and recommendations for an implementation plan.

May 1, 2013