Search Documents

By Alessandro Navarra

Discrete event simulation provides a computational framework in which the use of smelting equipment can be analyzed and optimized, leading to the development of alternative modes of operation. Much of the complexity of copper and nickel smelters is centered on the converter aisle. These converters operate in parallel, produce batches, and set the tempo for the downstream operations. In practice, smelter staff schedule daily operations to coordinate the smelting furnaces and converters with downstream operations. Thus, a realistic simulation of smelter operations, over hundreds of days, should incorporate converter scheduling algorithms as presented in this paper.

Jan 1, 2014

By Rod Abbott

High Definition Scanning (laser scanning) is a proven technology that is accurate to within 6mm in 50m (¼? in 150?). It can capture in excess of one million 3D point measurements in an average 2 hour scan. It has numerous applications including brown-field retrofits, bridge measurement and analysis, verifying as-built conditions, and crime scene investigation. We most commonly use it for plant design to capture current site conditions, so as to prevent interferences and problems before construction begins. All vital information is captured in the first site visit, which limits the need for extra field trips.

Oct 1, 2010

By Carlos Nieble

Ferteco Mineracao, belonging to the CVRD group, is one of the several iron ore mines in the south east of Brazil. Some of these mines have pit walls of over 350-m height and operations under difficult geo-technical conditions are steadily increasing. In order to mine the 15 million tonnes of high grade hematitic ore remaining in the Fabrica pit, Ferteco had to deal with the following restrictions: Warrant power to its concentrator and pellet plant, relocate the load-out rail road loop, stabilise a poor phillyte slope, relocate a creek on a bench, lower the water table and mine at maximum angles at a slope with phillyte and loose itabirites directly under the rail road loop. Considering these aspects, 3 stages of operations were designed, considering a safe operation, but with the lowest possible security factors at the last mining stage, before the pit would be filled in again with tailings. Stage one above the rail road loop and below the high tension power mast, where the poor phillyte slope was secured by a flexible retaining wall, using old rails and anchors up to 27 meters (80ft) with a working pressure of up till 30 tonnes and stage two with different slope angles, and deep wells, high wall blasting perpendicular to the highwall with relief holes and rerouting the creek in steel half culvert and stage three, the filling in with tailings and recuperation of the deep well pumps. Following studies and analysis were made: Geotechnical and geological studies of all rock formations including rock strength test, a hydrological study to define the lowering of the ground water level, slope stability analysis for every bench and all possible combination of benches, definition of blasting parameters close to the pit slope, a monitoring plan, including topographical movements, vibrations due to blasting, piezometers and pressure cells as well as a plan how to fill up the pit again with tailings in combination with the rising of the ground water level. A close co-operation between the geo-technical consultant, pit operations, the blasting contractor and the geological department resulted in an operation without any incidents, lowering the pit with an additional 3 benches and mining an additional 5 million tonnes of high grade ore.

May 1, 2003

By C. Bazin, D. Hodouin, M. Ounpuu

Sensors are now available in mineral processing circuits to monitor pulp flowrate and density, as well as ore characteristics and other process variables. The amount of information provided by these instruments is considerable but in many cases poorly exploited. This paper gives the results of the application of time series analysis techniques to signals generated by the sensors installed on an industrial Pb dezincing flotation circuit in New-Brunswick. Autocorrelation and cross correlation functions appear to be interesting tools for a preliminary circuit analysis, however the calibration of single input single output discrete transfer functions using collected sensors signals leads to conflicting results. For this reason a phenomenological approach, based on the kinetic and transport properties of the flotation process, is also considered. It has several advantages over the empirical transfer function modelling but also limitations in its applicability to industrial processes. A combination of the transfer function and kinetic modelling approches appears to be a promising avenue for better process modelling and control.

Jan 1, 1985

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By Felix D. Klebe

Efficient, high volume, mine load out operations have evolved in recent years to include more sophisticated control systems that integrate with mission critical equipment such as weighing systems. Traditional weighing systems often involve static weighment of individual railcars and either manual or serial transmission of scale data to a database application. In recent years integration of railcar or truck weight data into a loadout operation via direct PLC or Ethernet communication between the weighing terminal and the loadout control system has been realized. Furthermore, use of dynamic railcar weighing where railcars are automatically weighed while moving has increased productivity in a variety of mining applications.

May 1, 2008

By Jason Prno

Context ? Climate change an issue of global significance ? Research is lacking ? Study initiated by the David Suzuki Foundation, led by ArcticNorth Consulting Industry Surveying ? 34% and 48% of respondents indicated climate change is already affecting operations ? Majority believed climate change would have negative impacts in the future ? Cost and uncertainty of Future impacts are major barriers to adaptation

May 1, 2010

By J. O. Marsden

Over the past eight years, Phelps Dodge (a division of Freeport-McMoRan Copper and Gold, Inc.) has developed a suite of proprietary hydrometallurgical processes for the treatment of copper concentrates as an alternative to conventional smelting and refining technology. The technical viability of two processes has been commercially demonstrated in a large scale plant at Bagdad, Arizona, designed to process approximately 52,500 metric tons per year of concentrate containing 30.5% copper. The first process utilizes high temperature (225°C) pressure leaching, followed by countercurrent solid-liquid separation, and then blending of the copper-bearing solution with low grade stockpile leach solution for subsequent treatment by SXlEW for copper recovery. The second process uses super-fine grinding, medium temperature (l60°C) pressure leaching, followed by solid-liquid separation, and treatment of high grade copper-bearing solution by direct electrowinning to recover the bulk of the copper values. The latter process will be utilized at Morenci in a commercial facility designed to treat mixed chalcopyrite-chalcocite-covellite concentrates. This facility is scheduled to start up in 2007. Other flowsheet options have been developed by Phelps Dodge for application to a variety of concentrate materials in specific situations. Examples of various flow sheet options are presented in this paper, and the advantages and disadvantages associated with each are discussed in detail.

Jan 1, 2007

By Michel Ruel, Ali Soltanzadeh

This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control and expert systems such as fuzzy logic controllers and neural networks. Three examples are presented: ARC (Advanced Regulatory Control) on pH in a comminution circuit, MPC (Model Predictive Control) for combustible management and FLC (Fuzzy Logic Control) on a Semi Autogenous Mill. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.

Jan 1, 2014

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017

By Abdurrahman Tosun

It is very important for after blasting processes that muck pile fragmentation is predicted and controlled during blasting. Therefore, a significant research effort has been devoted to the development of mathematical equations that predict the value of average muck pile fragmentation. The specific charge parameter used in all of these equations is determined as the ratio of the total mass of explosives used to break a volume of rock. The length of blast surface and the row number of the blasthole are ignored in the calculation of the specific charge. However, in a blasting operation, blasthole geometry may result in additional material being impacted by a blasthole. This is due to effect shares of in both end sides of blastholes and the back region of blasting surface. In this study, a total of 14 blast tests, 8 at the first quarry and 6 at the second quarry of the Bati Anadolu (Western Anatolia) Cement Factory, were performed. In each study area blast tests were designed in the same direction continuously to provide stable structural properties of the rock. Therefore muck pile fragmentation depended on only specific charge values for each blast tests. Specific charge values were calculated according to both an average blasthole and also the total volume of material occurred as a result of blasting for each blast tests. During loading until the end of blasted material the front, the back, the arm off and the bucket off pump hydraulic pressure values occurred in hydraulic pistons of the loader were determined with a lot of data received for each blast tests. After that the relationships between specific charges values obtained according to two different methods and hydraulic pressure values of the loader were established with two correlations. The relationships between specific charges values obtained according to the total volume of material occurred as a result of blasting and hydraulic pressure values of the loader occurred as the best results especially the blasting operations that have the total length of blasting surfaces are short.

Aug 1, 2013

By W. Petruk

"D. Doyle How large is the beam to which you referred? Are we considering Watts, Griffis the probe of a 1 micron sized particle?& McOuatReply Yes. The beam would be about 1 micron. We could enlarge or reduce it depending on the current in-put.D. Doyle Then chemically bound material we might not see. If you are restricted to 1 micron then you would not be able to separate things smaller than this. Is this not so?Reply We won't be able to analyse it but we will see it as the scanning electron microscope has a resolution down to about 0.1 microns. We should be able to get the general composition of such a grain plus its surrounding grains. We feel we can then make a reasonable estimate if it were as small as 0.1 microns. An accurate analysis would be achieved with grains of 3 and 4 microns.D. Doyle Would this have an application in the hydrocarbon field?Reply The lowest atomic number would be sodium. We wouldn't be able to go below that atomic number. Anything with sodiumor a larger atomic number would enable us to analyse the carbon.M. Fairwether Do you have any policy relating to priorities. For instance areCominco companies going to be limited in the amout of samples permitted to give everyone a chance because quite frankly our company, and I'm sure all base metals companies can hardly wait for the installation of this equipment. I can forsee two years back-log of work in the first month.Reply Quite frankly, I haven't looked at this. At the present time the work is under the START program but I suppose we will have to look at possible changes. Anything under the START program has first line priority.B. Thorndycraft Will the briquetting of samples be automated as well? Pinson MiningReply No, not at this point. Our polish section laboratory is first-class and can turn out 18 polish sections a day which is more thar we can handle.B. Thorndycraft With the capability of this machine to operate in a hands-off manner perhaps it could start to look for the 5 micron gold particle in tailings?Reply I have such a program using a wave-length spectrometer rather than the energy dispersive. The wave-length spectometer is about 10 times as sensitive and would scan the section much faster. A one inch diameter polished section would be scanned in about 7 hours for anything 1 micron or larger."

Jan 1, 1984

By V. Ramachandran

The successful advent of solvent extraction (SX) reagents for copper recovery and improvements in electrowinning of copper to produce LME grade A copper cathode have paved the way for the hydrometallurgical treatment of copper oxide and low grade sulfide ores. This has resulted in about 25-30% of the world's copper being produced today by the Leach-SX-EW process. The obvious next step was to develop processes for the hydrometallurgical treatment of copper sulfide concentrates, as an alternative to a typical smelter-refinery complex. The current paper updates the processes that have been developed to date with emphasis on processes that are being commercialized or that are seriously under consideration for commercialization. Most of the discussions relate to the hydrometallurgy of chalcopyrite concentrates, which account for about 70% of the world's known copper reserves. In summary, in the last thirty years, the hydrometallurgical treatment of copper sulfide concentrates has attained full maturity and will be a serious option to contend with while evaluating any future new copper plant.

Jan 1, 2007

By Pierre Bénard

To achieve penetration on the energy market, hydrogen must overcome obstacles in the areas of storage, safety and infrastructure. One of the most important is the onboard storage of hydrogen for transportation applications, where large performance gaps exist between the current state of the technology and user expectations. In order to develop and demonstrate viable hydrogen storage technologies for cars, a set of gravimetric and volumetric system targets have been proposed by the US Department of Energy, based on achieving a driving range of 500 km for a hydrogen powered vehicle. A factor of 2 to 3 improvement in both hydrogen storage capacity and energy density is needed along with several other performance goals. Another key issue is safety. Although some of the safety issues can be arguably assigned to misperceptions, hydrogen has specific properties that have to be addressed, particularly in confined geometries where the risk of hydrogen detonations becomes an issue.

May 1, 2007

By J. Kang

There is increasing demand to utilize aluminium alloy sheets and their spot welds by the automotive industry. While traditional uniaxial tensile tests only determine mechanical properties to small strain, direct measurement of the constitutive behaviour of aluminium alloy spot welds at large strain remains a challenge. A technique was successfully developed using digital image correlation coupled with shear tests to directly measure the constitutive behaviour of an AA6022-T4 spot weld to large strains. The results show that the spot welding process not only decreases the yield strength but also lowers the work hardening rate of the nugget versus the base material. Details of sample preparation, experimental approach and results will be discussed.

Jan 1, 2011

By D. Harris, S. Murugesan, G. Ye, G. Oprea, J. Rigby, T. Troczynski

The spinel-added and in-situ spinel bonded castables have been developed and widely used in steel industry. It is challenging to develop magnesia-based castables for the non-ferrous industry because the temperatures in industrial furnaces are significantly lower than those in the steel industry and therefore the binding systems of these castables must have the capability to develop a ceramic matrix below 1300°C. It is also challenging to develop a good binding system without addition of fume silica, because the hydration of magnesia may take place during installation, curing and firing of the castables. This work presents the experimental results on developing magnesia-based cement-free, silica fume-free refractory castables using hydratable alumina as the hydraulic binder and a spinel phase as the final ceramic binder. In order to activate the sintering and have a ceramic matrix well developed at the relatively low required temperatures, ultrafine aluminas, chromia, magnesium-aluminate spinel and aluminum titanate powders were used as components of the binding system.

Jan 1, 2004

By M. Hawker, M. Kreuh

The mining and metallurgy industry is known to be of cyclical nature associated with price volatility. As such, some years are quite lucrative and other years require mining companies to tighten their belts. The field is a mix of junior, mid-tier, and major mining companies. One thing that is common to all of them is the time required and the cost to develop a flowsheet in accordance with best practices. Although a long list of factors can impact flowsheet development, this paper will include the impacts of: experienced metallurgical engineers and laboratories, representative samples for high quality and valuable testwork results, and following engineering development stages. The paper also provides typical time frames to complete selected engineering flowsheet development steps.

Jan 1, 2014

By P. B. Demarsh

"Location: - Mine village of Perron, 11 miles east of Val d’Or in northwestern Quebec.Life; - Started production 1932, ceased 1951.Ore: - Flat lying quartz tourmaline veins within granodiorite. Gold values related to coarse segregations of pyrite. Specific gravity 2. 80.Capacity: - 30 tons 1932-35; 125 tons 1935-37; 350 tons 1937-51.Assay: - Heads 0.21 to 0.34 oz. per ton. Grade obtained by mining 600 tons daily, sorting belt reject 250 tons, balance to milling; tailings loss 0.003 to 0.005 oz. per ton; extraction 9 8. 5%.Grind: - 70% minus 200 mesh. Detention time 26 hours.Treatment: - Cyanidation process.Reagents: - Per ton, aero cyanide (NaCn) 0.36; unslaked lump lime 1.50; zinc 0. 03; lead acetate 0. 006; steel consumption 2. 50.Water: - Equal mixture of swamp creek water and underground seepage.Cost: - Per ton, sorting and crushing 0.21; grinding 0.31; cyanidation 0.11; filtration 0.05; precipitation 0.02; miscellaneous 0.22; total 0.92.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - 95% Maritime and European, balance Quebec and Ontario.Tailings: - Absorbed over large swampy area on barren mining claims.Personnel: - 1 7 men including supervision.Flow sheet: - Canadian Mining Manual 1947"

Jan 1, 1966

By A. P. E. Dirige

The stability design of cemented backfills is normally conducted using conventional approaches. Analytical or numerical models, backed by trial-and-error methods, are the primary means used to describe or predict the support performance of backfills during mining. The stability of paste backfill free-standing faces is a major concern due to potential consequences to production, ore dilution and safety. Available analytical or mathematical models are developed based on assumptions of the failure modes that may occur when vertical fill faces are exposed during adjacent mining. Numerical modeling serves to provide an understanding of backfill strength and deformation behaviour. Such approaches offer inherent limitations and generally result in conservative designs. In this paper, centrifuge physical modeling was conducted not only for performance evaluation studies, including stability analysis, but to develop an understanding of the strength and deformation behaviour of paste backfill exposed faces when the adjacent ore zone is removed. The failure mode and mechanics of failure observed in the centrifuge model of a given prototype situation are discussed in detail. Centrifuge model results were compared to numerical modeling and it was concluded that a sliding block failure mechanism that resembles a circular slip appears to be the predominant failure mode.

Aug 1, 2013