Search Documents

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

By A. Longval, Q. Jiao, T. Shannon

In 2000, Xstrata Zinc (former Falconbridge Ltd.) Brunswick Smelter commissioned a modified lead blast furnace. Since then, efforts have been made to improve its operation in order to achieve optimal operation in terms of coke consumption, lead loss to slag, and improved environmental and hygiene conditions. This paper will review the important step changes in operational philosophy, undertaken since 2004, for the control of the blast rate, oxygen enrichment in blast, slag chemistry and charge level. Furthermore, a review of the improvements made in secondary materials consumed at the blast furnace will be made. This paper will also discuss the significant reduction of the frequency of accretion removal as a result of improved furnace operation.

Jan 1, 2008

By G. Belzil, F. Robichaud, M. Fullam

ABSTRACT The Goldex mining and milling complex is operated by Agnico-Eagle and is located in the Abitibi greenstone region of northwestern Quebec, Canada. Commercial production started in 2008. Average gold recovery is 93.5% with approximately 68% of gold recovery coming from the gravity circuit. During the first three years of production, three gravity audits were carried out to optimize performance of the gravity circuit. This paper presents results of the audits and the development of a model linking gravity and overall gold recovery, and outlines improvements made to increase gravity performance and reduce operating costs.

Jan 1, 2013

By W. L. Ott, J. E. Hawley, C. L. Lewis

"IntroductionTHE APPLICATION of spectrochemical analysis to metals of the platinum group was advocated by Harvey (3) as follows: ""The spectra of the platinum group metals have been studied less than many of the more common metals. The rarity of occurrence of these elements makes the analysis relatively unusual. Potentially, the analysis of this group is an excellent application of spectrographic methods, particularly in contrast to the tedious chemical procedure"".Wichers (8) divides platinum-metal analysis into three broad divisions as follows :( 1) The detection and estimation of these metals in other materials, e.g., ores, where the amounts present are very small.(2) The detection and estimation of impurities in the refined metals themselves ....(3) The analysis of alloys of the platinum metals .....The present paper deals with the second division: analysis of refined rhodium.Research on spectrochemical techniques for determination of trace contaminants in refined platinum metals was begun at Queen's University in 1949, under the supervision of Professor J. E. Hawley. Since 1953, the work has been continued in the Metallurgical Laboratories of Falconbridge Nickel Mines, Limited. Techniques for spectrochemical analysis of refined platinum and palladium have been published ( 4, 5). A technique for analysis of refined iridium has been developed but not yet published."

Jan 1, 1955

By J. -P. Saindon, L. D. Nel, A. E. Hall, S. G. Hardcastle

"This paper reports on an investigation into gas and dust concentrations in Ruttan Mine's exhaust air. The values obtained indicate that there is excellent potential to recirculate approximately 25% of the hot exhaust air into the intake air to reduce winter heating costs. Contaminant concentrations vary significantly during the course of the working shift and decrease in the mine exhaust system as the air returns to surface. A proposed on-line control system is outlined which would permit recirculation to be implemented with a pay-back period of less than two years. IntroductionIncreased energy costs and depressed mineral prices have resulted in mines, which use winter ventilation air heating, reviewing their systems to try to reduce costs. Heating costs can be significant, for example, Potash Corporation of Saskatchewan spends an average of $580,000 per mine per year and Ruttan mine spends approximately $IM per year on propane for its direct-fired heating system.Several method s of reducing heating costs have been considered and the following have potential application.Heat Exchange Between Exhaust andIntakeThis is usually accomplished by run-round glycol systems. The system is limited by ice formation on the coils in wet exhaust air and by the low exhaust air temperature, usually l0ºC. It also requires close proximity of the intake and exhaust airways to ma~e the cost of the connecting pipeline and pump systems economic . A feasibility study by Inco's Thompson operation reported that a proposed system of this type had a 19-year payback period and was, therefore, uneconomic. Potash Corporation of Saskatchewan is currently investigating plastic heat exchangers for a trial system because of corrosion on metal exchangers. It has the advantage of a 17°C exhaust temperature and relatively dry exhaust air.Waste Heat ReclamationThe waste heat from compressors and hoists can be used for heating in some mines. The feasibility of such a system depends on the individual layout and the proximity of the heat source to the inlet airway. Other mines have considered using the exhaust air in greenhouses to provide a cash crop."

Jan 1, 1988

By G. Reuben Yourt

IN 1935, Wright-Hargreaves Mines, Limited, initiated an enlarged programme of ventilation. In the mine, surveys were made from time to time by the geological staff, and improvements in ventilation were effected to accord with progress in mining as greater depth was attained. In the summer of 1938 an engineer was trained in the technique of dust sampling. Instruments and equipment for this purpose, such as konimeter, microscope, furnace, etc., were purchased, and a suitable office, equipped with laboratory facilities, was provided. The full time of the engineer is devoted to ventilation and dust control. On surface, in the mill crushing-plant and in the assay office and sample crushing room, an elaborate arrangement of hoods and exhaust systems has been installed to eliminate the dust. These installations, however, are not described in the present paper, which deals only with an extensive programme of underground ventilation as a method of coping with high dust concentrations, increasing temperatures and high humilities.

Jan 1, 1940

By F. P. Hassani, A. Hara, M. Momayez

To be competitive on the international market, the Canadian mining industry must reduce its costs, increase its productivity and maintain a high standard of safety. There is a great need today for improved methods that would allow the detection of geological structures in advance of mining to reduce dilution and the monitoring of underground structures to increase safety. This will facilitate planning for optimum exploitation of the mine and to increase production at lower costs. This paper discusses two examples of more efficient mine planning using new technologies such as Ground Probing Radar (GPR). In Kidd Creek mine, GPR technology was used at the 2500and 2600 levels to (1) monitor the stability of the sill pillar; (2) locate the presence of disseminated sulphide pockets in the sill pillar for extracting the mineral content; (3) monitor the stope backs and wall structures to evaluate the effect of on-time filling sequences; and (4)assess rockfill quality in terms of the presence of voids and fractures within the rockfilled areas. In the New Brunswick coal mine in Minto, GPR was used along with core log data to map and construct a 3D block of a section of the bench showing the relative position of different layers overlying the coal seam.

Jan 1, 1996

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By T. A. Lloyd

"This paper indicates the extent to which Canadian coal mine operators have taken advantage of developments in the science and technology of coal that would allow them to better satisfy changing market demands through improving the properties of their products. At some mines, no attempt is made to alter the coal from its as-mined condition, but at most mines grading into various size ranges and hand-cleaning of lump sizes is undertaken.Over-all, Canada Jags behind most of the other major world coal producers in the proportion of its coals being processed in wash plants. To some extent, this is due to the fact that a high proportion of the coal production satisfies market demands without such treatment. On the other hand, a few of the coal mines in Canada, which produce about 25 per cent of the nation's total coal output, have in operation some of the most modern coal beneficiating equipment available, including jigs, flotation cells, water cyclones, centrifuges, disc filters and thermal dryers."

Jan 1, 1968

By Wm. L. Giachino

"Over the last 10 years, C-1-L has played a significant role in the major advances that have taken place in blasting technology, among them the following: development and introduction of capsensitive slurries; development of bulk slurry systems both for underground and open-pit operations; development of the TOE-DET and ANODET systems of delay blasting;introduction of the NONEL system of initiation;development of the Vertical Crater Retreat (VCR) system of mining.This paper identifies areasin which we foresee further developments in blasting technology over the next 10 years and outlines how and to what extent C-1-L will become involved."

Jan 1, 1980

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"Abstract — The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units. © 2012 Canadian Institute of Mining, Metallurgy and Petroleum. All rights reserved."

Jan 1, 2012

"Acid resistant brick lined autoclaves and related vessels are utilized in pressure oxidation for the recovery of gold, copper, and other metals. The combination of the corrosion resistant membrane, acid resistant brick, mortar and steel shell is a composite system that requires a sophisticated stress analysis. In order to obtain meaningful results both the model and physical properties of the materials must be carefully selected. Evaluation of the calculated results requires an understanding of both the failure mechanisms of ceramics and experience with the performance of existing lining systems.INTRODUCTIONAcid brick lining systems are used in pressure oxidation autoclaves and related vessels to provide thermal and mechanical protection for corrosion resistant membranes that are applied directly to the interior of the vessel shell. The acid brick and mortar must be resistant to the process conditions and must provide a mechanically reliable structure.The construction of lined vessels incorporates a wide range of materials that can include the carbon steel vessel, austenitic weld overlay, lead lining, organic membrane, ceramic brick, mortars and other alloy components. The physical properties of the materials can vary by orders of magnitude and when combined in the construction of the lined vessel create a complex composite structure. The materials may be bonded together or act independently of each other. Stresses are induced into the lined vessel include pressure, thermal expansion, chemical expansion and mechanical loads.The complexity of these systems makes it is very difficult to account for all of the variables in the structural analysis of lined vessels. Historically calculations were simplified and designers primarily relied on experience with previous applications.The greatly improved tools for Finite Element Analysis (FEA) available today allow for detailed calculation of the stresses imposed on the vessel shell and lining. Koning & Lauzon (2004) presented a paper on design fundamentals including a discussion on the application of FEA methods at Pressure Hydrometallurgy 2004 in Banff. When a designer carefully constructs a model and selects the correct materials properties for the calculations, meaningful and useful results can be achieved."

Jan 1, 2012

By M. J. King, D. A. Van den berg, R. Fukuzawa

"Mercury bearing ore bodies are often treated for the production of copper, lead, zinc, gold, and silver. The mercury deports either to tailings or is collected during various stages of the extraction process. This paper reviews the relationship between various mercury collection processes and the subsequent management of the mercury by-product or waste. It focuses on mercury removal sequestration including cementation, sulphide precipitation, bulk neutralization, and carbon adsorption. Long term mercury management strategies including third-party stabilization, stabilized mercury co-disposal, secure storage, and mercury recycle are also evaluated. INTRODUCTIONMercury is produced in North America as a by-product of non-ferrous metals processing and from recycling of products such as dental amalgam, fluorescent lamps, and thermometers. Its toxicity is recognized to have significant negative impacts on the environment and human health. As a result, many countries are adopting regulations limiting mercury use and its uncontrolled release.The European Union banned mercury exports in 2011 and the United States will do so in 2013. The export bans aim to prevent mercury use in developing countries for activities such as artisanal small scale gold mining. However, by-product mercury production from the non-ferrous metals industries continues.These factors contribute to an oversupply of mercury and the need to find suitable treatment methods for the long term management and storage of mercury and mercury bearing materials."

Jan 1, 2012

By Y. Hayashi, A. Fuwa

To analyze zinc vaporization kinetics of zinc smelting slag in the ISP furnace, reduction reaction rate of zinc oxide from ZnO-FeOx-CaO-SiO2 slag system with CO-CO2-Ar gas mixtures has been measured by a therm o-gravim etric apparatus at various ZnO content, Pco, and temperature. The reduction rate was measured under a chemical reaction control in the initial three minutes where surface zinc content can be assumed constant. Through the reaction rate dependency analysis on ZnO contents, Pco and temperature, discussion has been made on its reaction mechanistic information in terms of rate coefficient, adsorption/desorption mechanism and activation energy.

Jan 1, 2008

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973

By C. Schlumberger

INTRODUCTION The object of the present paper is to discuss, from a geological point of view, the practical results obtained by the authors with the method of the 'resistivity map of the subsoil' in the study of various mining problems. Some of the studies described date from 1920, 1922, and 1923. They are, therefore, quite old, at least as far as geophysical research is concerned (1). Others, on the contrary, are very recent (2). We shall deal only very briefly with the theoretical and technical sides of the processes employed. This paper has, essentially, a practical purpose, and it has seemed unnecessary to enter into a detailed discussion of the methods. Such a discussion cannot be presented without introducing ,quite. Complex considerations both of mathematics and experimental physics, which interest only the geophysicist: whose work is highly specialized.

Jan 1, 1931

By S. H. Schulz

100 YEARS AGO, on the first of August, 1877, the mining engineer Friedrich Koepe was granted the patent rights for a hoist driving ropes on the principle of friction. It was named after him: the Koepe hoist. On the occasion of this centenary, the main features of the Kcepe principle are described.

Jan 1, 1977

By T. G. Carter

"Damaging seismicity associated with deep faulting in both mining and civil excavations not infrequently occurs without warning, and often before proper mitigation measures have been put into place. Severe squeezing is also a common problem for excavating through deep major faults. While both problematic conditions are difficult to predict and characterize, there is often a need at pre-feasibility and feasibility level to more reliably estimate the possible level of risk posed by such geologic structures. This paper introduces some structural geologic techniques that have potential application for both mining and civil applications for aiding forewarning of the extent of these types of problem.INTRODUCTIONEncountering adverse faulting at depth in deep excavations, whether for mining or civil purposes can create serious economic and safety impacts. For deep mines or for deep tunnel projects, measures are available for aiding prediction of the extent of possible influence that large scale faults could create, but these techniques are rarely if ever applied as part of routine site investigation programs, or even as part of risk assessment evaluations. Several well established structural geologic methods of palao-history reconstruction have potential application for aiding forewarning of the extent of these types of potential problem by allowing estimates to be made of:• controlling stress orientations that might engender reactivation movement;• principal stress magnitudes that could lead to failure initiation, and• probable mechanisms of fault deformation - brittle (bursting) or plastic (squeezing).This paper explores several structural geological and rockmass characterization techniques that have application for unravelling fault structure of importance to deep engineering projects. Their application for mining or tunnelling purposes is advocated in conjunction with conventional rockmass characterization assessment approaches using GSI, RMR and/or Q to aid early recognition and definition of potential adverse ground condition behaviour associated with intersection of significant faulting at depth."

Jan 1, 2015

By A. E. Dyment

In formulating an explosive for any specific set of conditions, various factors must be taken into consideration. Is it to be subjected to water or moisture? .If so, it must be designed to have an inherent ability to resist water. Is it to be used in confined spaces underground, where ventilation is limited? If it is, it must possess qualities enabling it to form, upon explosion, the minimum quantity of noxious gases, such as carbon monoxide or oxides of nitrogen. Is it for use where low temperatures may possibly prevail? If so, it must be capable of resisting such temperatures without freezing. Is it for use where dust or inflammable gases may be present? If it is, then it must be so formulated as to produce, upon detonation, a flame of the lowest possible temperature and the shortest possible duration, in order to lessen the chance of ignition of such gas or dust. This is actually the essential property of a permitted explosive, and it is undoubtedly the most important characteristic of an explosive which is to be used in gassy or closed-light mines. This being the quality that distinguishes permitted explosives from other types, it is interesting to investigate the ways and means by which the low-flame-temperature characteristic is obtained . Generally speaking, such explosives are so designed as to contain comparatively small quantities of nitroglycerin and relatively large quantities of the strength-producing salt, ammonium nitrate. This ingredient does not develop as high a temperature upon explosion as does nitroglycerin, so its presence, in large measure, in place of nitroglycerin results in an explosive which has an inherent low-flame-temperature characteristic, as opposed to one which is .made up largely of nitroglycerin, which would ordinarily be in the high-flame-temperature class. Additions are also made of flame-quenching salts such as sodium chloride, ammonium chloride, and up to a certain limiting percentage of sodium nitrate. These salts, with the exception of the last, do not ordinarily take an active part in the explosive reaction, being present primarily to absorb heat liberated by the reacting ingredients.

Jan 1, 1947

By J. E. Quinn, S. Wolstencrof, K. H. Soldenhoff

Ion Exchange (IX) using Strong Base Anion Exchange (SBA) resins is conventionally used to purify uranium from sulfuric acid pregnant leach solutions (PLS), particularly when uranium grades are relatively low. However, the presence of chloride in the PLS interferes negatively with conventional SBA based IX processes, by reducing the uranium loading on the resin. Chloride can be present in the PLS due to the use of saline bore or seawater in leaching, or chloride containing leach/IX reagents. ANSTO has been examining strategies to combat this problem for several years. ANSTO previously reported that a recently developed high-capacity SBA resin was capable of extracting uranium efficiently from saline leach liquors produced at Boss Resources’ Honeymoon in-situ recovery mine in South Australia. The resin was tested successfully in a 2017 Field Leach Trial carried out onsite in the existing wellfield area. While the piloting was extremely promising, the elution was more challenging, with eluate tenors limited to 2 g/L U3O8 using NaCl. This is due to the resin’s strong affinity for the uranium complex, which makes it difficult to elute efficiently by standard methods. In this paper, we describe a novel elution process developed for strong base resins that significantly improves upon conventional methods. The process, developed by ANSTO, is based upon conversion of the extracted uranyl sulfate species to uranyl carbonate, followed by elution with sodium chloride. The loading and elution process was demonstrated in continuous locked-cycle piloting conducted at ANSTO in 2019. The results were excellent, with eluate tenors of 8–9 g/L U3O8 achieved from Honeymoon PLS containing 50 mg/L U3O8, with very little transfer of impurities. In subsequent test work, the eluate was shown to be amenable to uranium peroxide precipitation. The results represent a huge step forward for the purification of uranium from saline leach liquors.

Jan 1, 2020