Search Documents

By J. C. White

"This paper was prepared for and presented at a lecture series on ""Materials Randling"" at McGill University. The development of trackless mining at Gaspe Copper Mines, Limited is described, showing the changes in mining method and the part played by the mobile equipment in the evolution of this highly mechanized underground operation. Comparisons of loading and hauling machines are given and an attempt is made to predict some possible future developments.INTRODUCTIONTHE PROPERTY OF GASPE COPPER MINES LIMITED is located in the Gaspe Peninsula of the Province of Quebec, 60 miles west of the village of Gaspe and 25 miles south of the St. Lawrence River. The original discovery of low-grade ore was made at Copper Mountain in 1921. Subsequent exploration revealed the richer Needle Mountain orebodies, and eventually in 1951 the decision was made by Noranda Mines to build the mining, concentrating and smelting complex (Figure 1). Construction and development of the mine was commenced in 1952 and production started in 1955."

Jan 1, 1968

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936

By The Staff

THE object of the work was to increase the capacity of the plant and, if possible, to reduce costs of the actual unit grinding while doing so. The accompanying assays of an infra-sizer analysis of the cyanide tail (Table l) illustrate the problem in hand. The cyanide tail is a combination of two products, gangue and FeS2. The assay alters by virtue of a change in gold value due to grinding and the relative quantity of FeS2 in the sizes, which itself varies with the grind. The disposal tail is the residue after the cyanide tail is scavenged by flotation, most of the pyrite being removed for roasting. It presents a somewhat different problem, since grinding gangue is all gain, but -10 micron FeS2 does not float nearly as well as + 10 product. This results in compromise in the final size to be aimed at. Extra grinding has hardly any appreciable effect on the gold extraction from the FeS2. (See Milling Investigations Into the Ore as Occurring at the Lake Shore Mine; Trans. C.l.M.M., Vol. XXXIX, 1936).

Jan 1, 1940

By Lionel C. Piuze

Introduction and Early History The British Canadian Mine is one of four operating properties of Asbestos Corporation, Limited, and is located in the town of Black Lake, Que., five miles southwest of Thetford Mines. In the early days of as1bestos mining, this .property was owned by a few small companies who later became part of the Asbestos Corporation. First .to commence mining operations on the property was the Coleraine Mining Company who, in 1885, began selling part of their large holdings in the area to various asbestos mining interests. Of these, the earliest active companies were Manhattan United Asbestos, the Glasgow and Montreal Asbestos Company, and the Anglo-Canadian, the last named later becoming the Standard and Dominion Asbestos Companies. Extraction of fibre was limited to what is now known as crude asbestos and the methods were primitive. Drilling was done .by hand and the ore was lifted by derricks operated by band winches. These were later replaced by horse power, but it was not until 1887 that the first steam-operated boom derricks were introduced, at the Anglo-Canadian mine. The ore was hand cobbled and the asbestos roughly classified and bagged. The waste rock, which by today's standards contained a considerable percentage of marketable fibre, was dumped near the pit. The first attempt to separate the asbestos from the host rock by mechanical means was made in 1888 by the G1asgow and Montreal Asbestos Company, then known as the Scottish-Canadian Asbestos Company, whose mill, erected in that year, was the world's first asbestos mill. Though the equipment was crude, the principles employed were the same as those used today with much larger units. The next steps were the use of rock drills, the adoption of steam rail transportation for moving mill rock, and conversion to the more flexible cable-derrick hoisting.

Jan 1, 1950

By J. M. Whatley

"IntroductionIN UNDERGROUND mining operations, the mine hoist has become one of the most important and one of the most expensive single pieces of equipment. As the means of transporting men and materials to the face, broken ore to the mill, and waste to the dump, it is often the very lifeline of a mine and must operate with dependability and efficiency or the whole operation will suffer. The mine hoist has become synonymous with safety. In few other types of mechanical equipment do so many men so frequently and completely place their lives. In Canada, more has probably been done to assure safe hoisting than in most other countries, but, unfortunately, this has resulted, in many cases, in the mines having to pay a high price for equipment. Hoist manufacturers have carried out much research in recent years in the endeavour to keep down these costs and at the same time maintain or improve the efficiency and safety of their products. Broadly classified, the bases for design research are dependability, efficiency, safety, and first cost.Probably the greatest single factor influencing the design of mine hoists was the introduction of electric motor drives. It was not until about 1905 that an effective start was made in the development of electric mine hoists, and then only with machines of small size. From that time on, however, progress was rapid, as may be gauged from the fact that by 1910 one large group of mines in Johannesburg had in use, or on order, fifty-four three-phase hoists and four Ward-Leonard. type hoists."

Jan 1, 1953

By Xue Yang

Even though many approaches have been proposed for automated fault detection and diagnosis of Heating Ventilation and Air Conditioning (HVAC) systems, and advanced maintenance programs, such as preventive and predictive maintenance have been applied for the systems, issuing work orders for corrective maintenance is still a reality. Currently corrective maintenance still accounts for more than 55% of all maintenance programs in average facilities in the US (DoE, 2010). Indoor air related problems are especially important among corrective maintenance work orders. This paper provides details of a case study conducted to capture the workflow that HVAC mechanics follow, their rationale in diagnosis process and the information they typically refer to while responding to indoor air related corrective maintenance work orders. The general workflow for HVAC mechanics to complete such types of work orders was summarized into 5 stages, and generic information requirements recorded from the case study were synthesized. Initial findings show two main challenges in the industry for HVAC mechanics to get access to required information, which highlights the need for a systematic approach that would enable identification of such information applicable to a given context under which a work order has been generated and provide values of required information for HVAC mechanics to do sound diagnosis through integrated data repositories.

Aug 1, 2013

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

By C. Caballero, K. Itagaki, P. Morales, A. Moyano, J. Font

Codelco-Chile is considering different processing options for the new projected concentrate from the Alejandro Hales mine. This concentrate is featured by its high arsenic content of up to 6%. Thus, it is important for Codelco Norte Smelter to define the technical feasibility for processing this high-arsenic bearing concentrate in its main smelting unit as it is the Teniente Converter, which beside of its dual feeding system can enhance the arsenic removal by volatilization. The present paper which is a part of an extensive research work will focus in the performed industrial scale test for processing about 7,000 tonnes of a high-arsenic bearing concentrates in the Teniente Converter at the processing rate of about 2,300 tpd. The impact on the chemical quality of the produced high grade matte will be discussed, and the effect of the As removal by increasing the Teniente Converter processing rate of concentrates up to 3,000 tpd when producing 70% Cu in the white metal will also be addressed.

Jan 1, 2007

By M. Pearson, J. Irvine, L. Mercer, P. Lauzon

Severe service ball valve performance has a direct impact on the mechanical availability of high pressure oxidation and leach plants. The primary function of these valves is to isolate the autoclave for maintenance. Valve failure has historically contributed significantly to the maintenance downtime of these process plants. An understanding of the root causes of valve failures is the first step in increasing the reliability of the severe service ball valves. A rigorous failure analysis practice has been developed by Hatch for investigating refractory failures in furnaces and kilns based on Kepner-Tregoe methodology. The method has also been modified for valve failure analysis. From a root-cause failure tree analysis of each of the valve components, a list of all potential valve failure mechanisms was developed for ranking and evaluation, along with recommendations for further valve development. The purpose of this paper is to present the reader with the modified Kepner-Tregoe method and examples of this analysis.

Jan 1, 2004

By Diego L. Romero, Joy P. Romero

"IntroductionThe purpose of this paper is to explain the theory and demonstrate the industrial applications of electrostatic separation. Wabush Mines' use of this type of processing for the concentration of iron ore is unique in the industry. Other minerals are concentrated electrostatically but the process is not widely used.Typical minerals separated by electrostatic separation techniques are:Non-ConductorsAnhydriteApatiteBariteBastnasiteBerylCalciteChrysotileCorundumDiamondEpidoteFeldsparsFluoriteGarnetGypsumHornblendeKyaniteAcmiteAugiteBrookiteCassiteriteChalcopyriteChromiteColumbiteCopperDaviditeEuxeniteFerberiteFrankliniteGalenaGoldGraphiteHematiteMica (Biotite)Mica (Muscovite)MonaziteOlivinePerovskiteQuartzScheeliteSideriteSillimaniteSpheneStauroliteSulphurTopazTourmalineXenotimeZirconConductorsIlmeniteIlmenite-( High Iron)IlvaiteKoppiteMagnetiteMarmatiteMolybdenitePyriteRutileSamarskiteSphaleriteTantaliteWolframiteWulfeniteThe limitations of this process are:1. There must be a difference in conductivity between the minerals being separated.2. The size range must not be very wide.3. The specific gravity of minerals being separated should be similar or the minerals to be pinned should be lighter. 4. The feed must be dry.5. The particle shape should be more or less uniform. 6. The feed must not be high in true middling particles."

Jan 1, 1989

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By D. Emadi

The ASTM B108 Mould and a Modified Mould were used to cast test bars under a variety of conditions: mould and pouring temperatures, mould coating and tilt. Mechanical properties were determined in the as-cast and heat-treated conditions. The ASTM Mould is less sensitive to casting variables. Enlarging the gating system and adding additional gates to the ASTM mould can improve properties in the tilt position. The reproducibility of properties in as-cast and T6 heat treated bars was investigated.

Jan 1, 2004

By M. Timmins

Campbell Mine operates a 100 tpd gold autoclave that treats sulphide concentrates at 305 psi and 200 °C. Autoclave feed consists of fresh pretreated concentrate, an acidic oxide slurry recycle as well as other high arsenic sources. The brickwork that is used to construct the five compartments of the vessel must be inspected and repaired periodically. Shutdowns are scheduled to inspect this brickwork and at times replace entire sections of the brick walls or lining. It also provides an opportunity to repair or replace other internal features such as agitator blades or oxygen spargers. Mechanics and contractors are scheduled around the clock to perform the maintenance requirements. There are many safety considerations and precautions that must be taken in order to protect the well-being of the workers and minimize damage to sensitive pieces of equipment. Heat, arsenic and lead contamination and confined space issues are just a few of the hazards involved. The following paper will describe how these safety concerns are addressed and will serve as a guide for future autoclave shutdowns.

Jan 1, 2004

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

By K. L. Boyd

"Can the increasing tonnages of ore and waste mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each stage of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in material handling from the mine to the mill, maximizing operating hours per year.RÉSUMÉ Le recours à des concasseurs plus grands et plus performants suffit-il à gérer l’augmentation du tonnage du minerai et des déchets que l’on extrait de nos jours ? Cet article examine les tous derniers modèles de concassage primaire et de grands concasseurs à cône. Il montre que, pour satisfaire aux exigences de production plus conséquente des exploitations minières existantes et nouvelles, il est important d’optimiser les taux d’utilisation à chacune des étapes du circuit de réduction de la taille des roches, en plus d’utiliser les concasseurs plus grands actuellement disponibles. L’objectif de cet article est d’aider les sociétés d’experts-conseils et les exploitants à sélectionner le meilleur équipement ainsi que des articles fabriqués sur mesure pour la manutention de la mine au concentrateur, en optimisant les heures d’exploitation par année.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications have since become available.The rock size reduction process from the mine to the selected milling process facility has not changed since a person first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages:• stage 1: mining (rock breakage and fragmentation);• stage 2: prescreening (scalping);• stage 3: primary crushing; and• stage 4: fine crushing (secondary, tertiary, and quaternary).Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments play a key role in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2017

By Jim Excell, Jim Rothwell, Mike Rylati

"LocationThe Ekati Diamond mine is located at Lac de Gras, Northwest Territories.Brief Description of OperationBHP Diamonds Inc. has developed Canada's first diamond mine in the Northwest Territories (NWT), Canada. BHP Diamonds Inc. is part of the BHP World Minerals Division ofBHP Minerals. The project is a joint venture between manager and operator BHP (51%) and the Blackwater Group (49%). The Blackwater Group comprises Dia Met Minerals Limited, Charles Fipke and Stewart Blusson.Production at the NWT diamonds project began in October with the mine officially opened October 14, 1998. The project is situated on an 853 000 acre claim block located in the Lac de Gras region of the NWT. It is about 300 km northeast of Yellowknife and 100 km south of the Arctic Circle. The seasonal winter ice road to the Echo Bay Lupin mine passes along the eastern margin of the project area. This allows road access each year from mid-January to mid-April. For the remainder of the year, the project is accessible only by air.HistoryIn 1980, Charles Fipke traced indicator minerals east from the Mackenzie River area. He discovered indicator minerals in the Lac de Gras area and staked mineral claims in 1989. A joint venture was formed between BHP and Dia Met in 1990, and in 1991, the first diamonds in the NWT were discovered at Point Lake by BHP and Dia Met. This initiated the largest staking rush in Canadian history. The joint venture launched an aggressive exploration program.Koala, Fox, and Leslie were identified in 1992 as potentially economic pipes.As soon as the project's potential was established, it was recognized that an enormous amount of work had to be completed in several areas before a mine could be developed, namely: technical evaluation of the resources; environmental and socio-economic evaluation to procure the necessary permits for the development; and engineering design to optimize mining and processing of the resource and to comply with specific environmental requirements."

Jan 1, 2000

By R. H. Waddington

Historical The limitations of reverberatory furnace operation have prompted many investigators to consider electric furnaces for melting electrolytically refined cathode copper. In the majority of cases where experimental work was performed, the furnace used was of the granular resistor, induction, or indirect-arc rocking type, and attempts to adapt the three-phase direct-arc furnace to copper melting appear to have been relatively few. In 1935, the International Nickel Company of Canada, Limited, carried to an advanced stage its experimental investigation of continuous melting of copper in the three-phase direct-arc furnace, and demonstrated that this process was technologically and economically practicable. Trial operations were conducted at the Huntington, W.Va. works of the Company, and were followed by the installation at Copper Cliff, Ontario, in 1936, of a full-scale unit for commercial operation. Two years later, a second unit was installed -which raised the electric melting capacity to a point permitting complete replacement of the coal-fired reverberatory furnace operation in the production of refined copper castings.

Jan 1, 1946

By J. S. Redpath, W. R. Dengler

"A description of the equipment used and the electrical-mechanical problems encountered in sinking a deep shaft is given. This shaft is currently being sunk to a depth of 7,115 feet. Some of the features of the sinking plant are a 6,500-hp double-drum hoist, a Blair stage hoist, special high-capacity mucking gear, a Galloway stage, high-tensile stage suspension ropes and 12-ton sinking buckets.INTRODUCTIONIN THE EARLY FALL OF 1965, a contract was let, by The International Nickel Company of Canada, Limited, to Shaft Sinkers (Canada) Limited -J. S. Redpath Limited -Joint Venture, • to sink and equip the Creighton No. 9 shaft at their Creighton Mine proper-ty in Ontario. This paper describes the electrical and mechanical equipment used by the contractor on this project, and details various problems that were en-countered.The shaft itself is circular in section and is lined with monolithic concrete. Upon completion, it will feature twin skip compartments, a cage compartment, counterweight compartment, manway and pipe compartment. The finished diameter of this opening will be 21 feet and the shaft will bottom 7,115 feet below the collar. The present depth of the shaft (April, 1968) is 5,400 feet. The opening is concrete lined as excavation takes place and the steel will be placed in the shaft upon completion of sinking. Hoisting is done on rope guides which are part of the stage suspension system."

Jan 1, 1968

By C. O. Stee

IN the October, 1936, issue of the Canadian Mining Journal there was published a series of very comprehensive and exccellently illustrated papers by Mr. C. O. Stee and members of his staff dealing with Siscoe operations and ore-bodies. These were, in the order in which they appeared: Geology of Siscoe Gold Mine, by O. L. BACKMAN Diesel Power at Siscoe Gold Mines, Ltd., by C. O. STEE andE. A. BLOMQUIST Mining at Siscoe, by L. T. POSTLE and W. F. Engineering and Surveying, Siscoe Milling Practice, Research and Testing Laboratory, Assaying of Mill Tails and Solutions, BROWN(6) by P. A. TEEPLE (7) by L. E. DJINGHEUZTAN by L. RIVETT (8) by G. IRWIN (9) The Editor of the Canadian Mining Journal cordially assented to our suggestion that these papers be reviewed at the 1937 Annual General Meeting of the Institute, and the authors very kindly accepted our invitation to present such reviews . Of these courtesies, full acknowledgment is here accorded. To our readers, we commend the original papers in the Canadian Mining Journal. The summaries presented at the meeting follow. EDITOR. THE GEOGLY OF THE SISCOE MINE The Siscoe gold deposits lie in and near a stock of granodiorite, related to the Bourlamaque batholith, which has intruded highly folded Keewatin volcanic rocks .. The volcanic rocks lie to the north of a belt of Timiskaming sediments.

Jan 1, 1937