Search Documents

By Subrata Dutta

Sindesar Khurd Mine is situated in Rajasthan, India, and operated by Hindustan Zinc Ltd, under Vedanta Group. The base metal mine is high in reserves of Lead, Zinc and silver and has been producing since 2007 with initial production of 0.3 mtpa. Recently the mine has gained prominence as a base metal underground mine in introduction of latest mining techniques and achieving high production at lowest costs. The promising Lead-Zinc reserves of Sindesar Khurd Mine (SKM) and high-tech exploration adopted by Hindustan Zinc Ltd (HZL), (Vedanta Group), raising the reserves and resources from a meager 9 Mt (1997) to 81 Mt (2012), has prompted HZL management to ramp up the mine production from 0.3 mtpa (2006-07) to 2 mtpa by 2013-14 with ambitious plans to reach 3.5mtpa subsequently (presently largest underground metal mine in India). The complete trackless system underground mine, recently equipped with latest leaky feeder communication system (unique in India), utilize modern drilling, mucking and hauling equipment aided with various utility/service vehicles. Excavation optimization and quality recovery maximization from the open and post filled stoping methods, continual expert analysis and feedback from International consultants like AMC (Australia) and SRK (UK), and involvement of renowned bodies in management excellence, have lead the mine towards highest productivity and lowest mine operating cost, earning the mine a prominent place in the global base metal industry. The paper deals with how the various challenges in mine planning and designing, mine development, operator skill, equipment introduction and maintenance, expertise availability, provide training and exposure to officials, prompt and effective communication/service, control of ground vibrations, maintain ventilation standards etc are faced in attaining high operational excellence and thus attain a record mine output/man shift (OMS) of 14 ton/man shift with targets to reach 20 ton/man /shift. Scientific designing using 2D/3D numerical mine-modeling techniques, faster stope sequencing with introduction of paste filling ( first time in India),latest leaky feeder communication system, control ground vibration to stringent standards using electronic delay system, faster raising techniques using raise borers to enhance development and ventilation, cavity scanners to monitor large stope voids, fast shaft sinking at 100 m/month(Chinese expertise) and maintaining adequate ventilation with close software monitoring are some of the highlights discussed in the paper towards achieving the targets.

Aug 1, 2013

By T. W. Wlodek

"AbstractSatisfactory mine drilling operations depend on the good performance of the drilling machine, and of what may be called the drill set, i.e., the following four elements: bit, attachment, drill rod, and shank end. The field performances of these four elements in the drill set are analysed and their service lives are compared. The most .common causes of service failure are reviewed and possibilities of increasing service life are discussed.The laboratory methods now employed for the simulated service testing of tungsten carbide bits, conical push-on and threaded .types of attachments, drill rods, and shank ends are described, and some results are discussed. The objectives of the research programme now being carried out •on the above mentioned elements are outlined.A number of mines in British Columbia, northern Ontario, and northern Quebec have been visited, and, with the co-operation of the C.I.M. Branches in these areas, meetings with representatives of the mining and steel industries concerned have been held. In this paper, the mechanical-metallurgical problems most frequently encountered and discussed during these visits and meetings are described and .analysed.IntroductionSUCCESSFUL mine drill operations depend to a great extent on• the satisfactory field performance of the four elements which form the mining drill set, shown diagrammatically in Figure 1.These important elements are:1. -The bit, which may be one of the following types:(a) Detachable tungsten carbide bit( b) Inserted rod bit, so called chisel bit( c) Detachable steel bit( d) Solid rod bit"

Jan 1, 1952

By P. A. Peach, W. H. Gross

The modern economic geologist in Canada is well equipped to apply geological, geochemical or geophysical techniques in the exploration for ore. Recently, great advances have been made in geophysics and geochemistry, and a large number of new orebodies have been discovered by these methods. An attempt is made in this paper to show that there has also been a considerable advancement in geological knowledge and that the most effective application of geophysics and geochemistry often occurs in areas already considered geologically favourable for the occurrence of ore. Ali exploration methods sooner or later suffer from diminishing returns. Therefore, as time goes on, one can expect to see the application of some of the more subtle or refined geological techniques that are presently being developed.

Jan 1, 1967

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

In 2009 Newmont Mining Corporation?s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

By G. G. Li

"A dynamic ventilation-modeling package, VREX, was used to simulate the mine activities through tracking the equipment movements in underground workings and determine the airflow demand for a new production scenario in a ventilation-on-demand (VOD) system. It incorporates the mine development data from a discrete event simulation and balances the ventilation network using the CANVENT ventilation solver. A case study was performed to demonstrate the capabilities of the software, evaluate the performance of the network and determine the potential energy savings for implementing VOD in a deep mine operation.INTRODUCTIONThe ventilation cost of an underground mine can be significant—up to 50% of the mine’s energy consumption could be used to run fans and provide heat/refrigeration to meet the specified production environment for workers and equipment. The VOD system has proven to be more efficient in operating the fans and supplying the amount of air corresponding to the mine activities taking place in underground workings (Hardcastle, Kocsis, & O’Connor, 2006). In order to properly solve and evaluate the VOD system, a dynamic ventilation modeling software VREX—the ventilation rules engine has been developed to simulate the mine activities and determine the airflow demand for each production scenario within an operation period (Dasys & Cameron, 2011).VREX is a decision support tool, backed by the CANVENT mine ventilation solver (Li, Kocsis, & Hardcastle, 2009), for determining the outcomes of network configuration changes over time. The software incorporates the mine development data with ventilation modeling through the discrete event simulation (DES) performed by SimMineTM. As it simulates the air requirements for different vehicles and activities, VREX can evaluate both the performance of the ventilation system and the potential economic benefits of making operational or technological changes (Pritchard, 2010). For example, the model can be used to assess the economic and environmental impacts arising from modifying regulations to support the use of electric or lower emission vehicles. The combination of DES and ventilation modeling provides a new technology to generate the production scenarios according to mine schedules and activities and to determine the potential benefits for various levels of ventilation control, such as time interval and work shift change."

Jan 1, 2019

By W. Rostoker

Packing Experiments The porosity and most of the other physical properties of a coherent mass of any material built up by the packing together of discrete particles will obviously vary with, and be governed by, the manner of association of the particles. The relation of packing to powder metallurgy has been discussed in some detail by at least two authors. Packing Theory Theories of particle packing have been put forward by C. C. Furnas and A. E. R. Westman. Although their approach to the problem is not the same, their conclusions are similar. In the process of packing, they visualize the voids of a uniformly sized material becoming filled with particles of a smaller size, and the voids between these being filled in turn with still finer particles. Obviously, if this process is carried ad infinitum, the resultant mass will have the same density as the constituent particles. In practice, of course, such a density of packing is never attained. In addition, the premise is made that successive particle sizes must fit into the voids left by the immediately larger particles- an assumption requiring definite size gradations and also particle shapes. It remained, then, for theory to correlate relative diameter ratios, and proportions and numbers of sizes of particles, for requisite packed densities. Briefly, the following principles were postulated: (a) For an infinite diameter ratio between largest and smallest sizes, an infinite number of particle sizes in proper proportion is required to give natural density. (b) For a given diameter ratio, there is a maximum number of permissible particle sizes for maximum packed density (Furnas). (c) Provided the particle shape is spherical, or approximately so, the proportions o particle sizes can be calculated. (d) The ratios of successive diameters of particles are in geometric progression.

Jan 1, 1947

By R. A. Hemstock

AREAS in which the surface de-posits consist of organic material -known in some parts of Canada as muskeg and in Europe, more generally, as peat lands -have long been some of the least rewarding of lands of the north temperature zone. Even in such countries as Great Britain, Holland, and Denmark where a good deal of incentive exists to develop all available land, the use of peat land has been negligible except as a source of fuel. Only recently have efforts shown promise in re-claiming these lands for farming or for forestry. Russia has large areas of peat and use is made of it for power generation. The Russian people have also ?developed a variety of machines for handling peat, which would indicate that they are well ahead of the Wes tern World in their technical and physical ability to solve some of the problems. Certainly in Canada, where there are over 500,000 square miles of muskeg, the economic aspects of this problem are important. This is especially true in considering the shifting emphasis to northern development. Not only is muskeg in possession of great stretches of terrain, thereby rendering it useless for agricultural purposes, but it is apparently moving into forested areas and reducing their productivity. In addition, it lies as a great barrier to movement in the search for and development of such natural resources as petroleum, natural gas and minerals generally. This situation has long been recognized in Canada but only recently have organized efforts been made to study the problems and search out ways of overcoming them.

Jan 1, 1958

By K. D. Bulin

"An interesting brief history review of shovels as the primary excavating tool will permit the reader to see that immeasurable development and resources have preceded the shovel excavators which today are used extensively throughout the mining industry. With this as a background, the shovel manufacturer has the ability to utilize his resources best in those areas of shovel development in which the maximum benefits of increased reliability, performance and ease of maintenance will improve the operating rewards to the user of the equipment. The author explains the function of the shovel as a part of the material handling system. A detailed description of those areas of the shovel in which the most recent developments and major improvements have been implemented in the manufacture of the shovel excavator arc included."

Jan 1, 1973

By H D. Smith

T HE production of coal in Canada was slightly higher in 1964 than in the immediate past, and the major users continue to be the electric utility and metallurgical industries. There are continuing trends toward the increased use of cokes and chars in various metallurgical applications. Geological Research During 1964, the coal drilling program of the Research Council of Alberta (RCA) was concentrated in the extreme south of the Province (notably in the Milk River area and the region immediately to the northeast of this area). Field work commenced on June 1 and was completed at the end of September, by which time a total of 376 holes, aggregating some 48,500 ft., were drilled in 132 townships. Although no new major coal occurrences were intersected, the pro-gram yielded useful data for defining the extent of the known coal deposits in the area. Detailed results will be analyzed during the winter and reported in due course. Meanwhile, a full report on the

Jan 1, 1965

By O. E. Andrew

THE object of this paper is to present a brief summary of the dust control system in use on the 3,825-foot level at the jaw crusher station, Lake Shore mine. During the years 1936 and 1937, dust survey reports were presented to the management showing that high dust concentrations were being created during operating periods. At that time, however, this crusher was running only an hour or so each shift, and it was felt that no large capital expenditure for dust control equipment could be justified. In order to afford some protection to the operators, a number of respirators then on the market were .tested and the &apos;Comfo&apos; respirator was adopted for use by the crusher-men. In 1938 this crusher began to handle a large share of the total mine tonnage and the hours of operation were increased. Further dust sampling showed increased dustiness with the longer operating time. It was also realized that the operators suffered considerable inconvenience if they wore their respirators throughout the shift. If the respirators were not worn, then dangerous amounts of dust were being inhaled. The fact that the crusher station was situated on the 3,825-foot level limited the means that could be employed to eliminate the dust hazard. At that rime there was not available the 5,000 c.f.m. of fresh air which would be required to sweep out or dilute0 the dust, and there was also no way of disposing of the contaminated air without passing it on for other men to breathe. Thus it became apparent that a self-contained dust disposal system would have to be installed.

Jan 1, 1941

By V. C. Pandolfelli, L. Paulino, C. E. Zangiacomi

The continuous improvement in aluminum industry over the last years has increased metal output at lower cost. The potlining plays an important role in this regard due to high cost involved and more recently in its environmental aspects. In order to increase potlife and thus minimize the aluminum cash cost, a systemic approach is needed, through investigating the main cathode failure mechanisms by using a pot autopsy as a powerful tool, and then making the necessary chances to achieve extended potlife. In addition, preheating and pot start-up may also damage the cathode if not performed with an appropriate technique or even if the lining materials are not specified correctly, among other factors. All these aspects will be presented and discussed in this paper. Increased potlife, especially now that the current is reaching values up to 300kA, will allow aluminum plants to match their goals more efficiently at lower costs.

Jan 1, 2006

By John Vergunst

"This paper traces the development of Ontario &apos;s cap lamp standard. Over the years, numerous Coroner&apos;s Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner&apos;s Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By B. R. MacKay

Introduction The Corbin coalfield is one of the smallest, and at the same time one of the principal, producing bituminous-coal areas in southeastern British Columbia, and is unique on account of the great original thickness of one of its coal seams and the remarkable concentration of coal in a small area that has occurred through intense folding and faulting of the measures. These are such that the deposit has been referred to at times as "the world&apos;s thickest coal seam" and as" a mountain of coal." The determination of the number, thickness, and character of the seams present, and the structure, extent, and geological relationship of the several deposits, are of vital interest both to the operating company in its endeavour to evolve the most efficient method of mining these exceptionally thick deposits and to the Government in estimating the coal resources of the different fields. With the object of ascertaining these data the writer was assigned in 1930 to geologically map and study the Corbin coal deposit. A topographic map covering Coal mountain and the immediate vicinity on a scale of 1 inch =800 feet, with a contour interval of 25 feet, made by the Topographic Division of the Geological Survey, served as the base for the geological mapping.

Jan 1, 1931

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By Ralph H. Cleland

Introduction The mines of northern Ontario have entered the class of deep mines. It has often been asked: How deep can operations be carried on? What will the temperature be? This paper is a résumé of a brief survey of rock temperatures made by the Ontario Department of Mines during the year 1932. Present temperatures were recorded and the geothermal gradients that now exist were determined. No alarming situations were found, but many interesting ones have been noted. Northern Ontario mines are fortunately situated as compared with most deep-level mines of the world. The mean yearly temperature, as determined from meteorological records of the Federal Department of Marine, is from 33 to 38 degrees Fahrenheit. The tables on the next page show the temperature range in and about our mining camps ( l ). As no exact figures were obtainable for Kirkland Lake, the data for Iroquois Falls, which is about 50 miles northwest, were taken as applicable there. The figures for Timmins were checked against those of Cochrane and Iroquois Falls and found to be very similar, so that the Cochrane data may be used for the Porcupine camp. The yearly mean temperature is considered to be 33.5 F.

Jan 1, 1933

By Brad Bjornson, Geoff Stevens, Mike Ashar, Cliff Britch

"LocationThe facilities are located 30 km north of Fort McMurray, Alberta (or 470 km northeast of Edmonton, Alberta).Brief Description of OperationThe operation includes the mining of oil sands, extraction of bitumen from the oil sands, and upgrading of the hydrocarbon fraction prior to shipment via pipelines to refineries.HistorySuncor was initially called Great Canadian Oil Sands. It was started by Sun Oil of Philadelphia. Construction began in 1965, with the first production coming on September 1967.Details of Present Milling Practice (Plant 3)Plant 3 recovers bitumen from the oil sand using the Clark hot water process. The basic steps in the process are conditioning, primary recovery, secondary recovery and tailings oil recovery.Oil Sand Feed SystemThe oil sand feed from the mine is transferred to the feed bin in extraction by two conveyor systems. Oil sand analyzers on each conveyor system measure the amount of bitumen and fines in the ore. Cones at the bottom of the feed bin distribute the oil sand to five process lines. Feed flow from each cone is regulated by an apron feeder which transfers the oil sand to conveyors that discharge into the conditioning drums. Weightometers on each of these five conveyors measure the rate at which the oil sand is delivered into the drums. The oil sand feed rate to each drum can be adjusted by varying the speed of the apron feeders."

Jan 1, 2000

By G. Warren

"In the past, smelting and refining of the precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. This philosophy is changing however, as economic and environmental pressure are forcing a re-evaluation of all aspects of gold mining and milling.This paper describes and evaluates three furnace technologies available and used by precious metal operators. The operation of arc, induction, and reverberatory furnaces are discussed and their strengths and weaknesses with respect to capital cost, impurity removal, slag quality, and environmental concerns highlighted.INTRODUCTIONIn the past, smelting and refining of precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space, and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. Generally, gold producers will spend a great deal of effort to squeeze the last drop of efficiency out of a leach or grinding circuit via simulation or testwork but will design and build the refinery based upon past practices or industry standards. That past practices or industry standards will provide a functional refinery is undisputed; that this philosophy achieves the efficiencies that are possible or demanded in other plant operations is debatable.Environmental and worker hygiene requirements are considerations as well. Pollution control equipment can become a substantial contributor to both the capital and operating costs of a refinery and furnace selection has a marked influence upon the type and cost of this equipment. Slag characteristics and subsequent processing options available also play a role in furnace selection as precious metal slag losses and the recovery effort can greatly influence the cost / benefit analysis of a particular technology."

Jan 1, 2001

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015