Search Documents

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By Donald Leroux, Ralph Dahlke, Dave Scott, Finch. James A., Cesar O. Gomez

"The efficiency of the flotation process depends on how effectively air is dispersed into small bubbles. Bubble surface area flux - the surface area of bubbles per unit time per unit cross-section area of a cell - is emerging as the parameter to characterize gas dispersion. One of the approaches proposed to measure bubble surface area flux in industrial cells is based on the measurement of two variables: gas velocity and gas holdup, using separate sensors. Plant testing of the gas velocity sensor gave evidence of a series of operational problems which may be necessary to correct before attempting to characterize gas dispersion. Problems such as uneven air distribution within a cell and along a bank, faulty air and slurry valves detected during attempts to redistribute air, and poor control of pulp level and gas flow became evident. Detection of these problems from gas velocity measurements is illustrated.INTRODUCTIONBubble surface area flux is considered a key variable in the optimization of flotation circuit performance (Gorain et al., 1997; 1998). The Mineral Processing Group at McGill University has devised and developed a method for estimating bubble surface area flux in industrial flotation cells (Finch et al., 1999). The method is based on measuring gas holdup and superficial gas velocity using two separate sensors and applying drift flux analysis to estimate bubble size (Dobby et al., 1988; Banisi and Finch, 1994). With bubble size and superficial gas velocity known bubble surface area flux can be calculated.This method was selected by Noranda to characterize gas dispersion in cells as part of a program to model and optimize flotation circuit performance. However, initial testing at Brunswick Mine with the gas velocity sensor provided some unexpected results indicating operational problems and equipment malfunctions that needed to be addressed before systematic measurement of gas dispersion could be initiated.The subject of this communication is to illustrate the detection of these problems from gas velocity measurements. The line 3 Zn Cleaner circuit comprising four stages of Denver DR cells was the main subject of analysis, including the effect of correcting these problems on the metallurgical performance of the Zn 3rd cleaner bank of ten DRl 00 cells."

Jan 1, 2001

By Alain Simard, André Gobeil, Sylvain Lacroix, Maurice Rive, Denis Racicot, Pierre Verpaelst

"The Abitibi volcano-plutonic belt forms the major portion of the Abitibi lithotectonic subprovince in the Superior Province. The Abitibi belt is composed essentially of"" (1) approximately 2.7 Ga old volcanic and sedimentary rocks; and (2) gabbro, tonalite, granodiorite and syenite intrusions occurring in well-defined prekinematic ( synvolcanic ), synkinematic and post-kinematic plutonic suites. Most of these rocks are metamorphosed to greenschist facies. Regional multi-phase deformation affects the volcano-sedimentary rocks. Deformation was initiated as these rocks were formed, and peaked at the end of the Keno ran orogeny with the emplacement of granitic batholiths.There are 145 former and current mines in the Quebec segment of the belt. To date, more than 420 Mt of ore have been extracted yielding 1,600 tonnesof Au, more than4,000 tonnesof Ag,4,400,000 tonnes of Cu and 5,300,000 tonnes of Zn. Mineral production is concentrated in geologic domains that approximately coincide with the boundaries of lithotectonic domains. We have compared the geology and mineral deposits of different domains to illustrate their distinct metallogenic signature. Certain domains are dominantly gold-producing (Cadillac-Malartic, Val-d'Or, Caopatina), others are base-metal producers (Matagami and Normetal), while others produce both gold and base metals ( Rouyn-Noranda, Chibougamau, Casa-Berardi-Joutel).Gold is extracted from quartz-rich vein deposits (for example, Val-d' Or), sulfide-rich veindeposits(Cadillac or Chibougamau) and from volcanogenic massive sulfide deposits ( Rouyn-Noranda). Base metals are generally mined from volcanogenic massive sulfide( RouynNoranda, Matagami, Normetal), although certain vein deposits yield base metals (Chibougamau) . Certain sectors are dominantly zincrich (Matagami, Normetal)."

Jan 1, 1990

By Alain Simard, Andre Gobeil, Sylvain Lacroix, Maurice Rive, Denis Racicot, Pierre Verpaelst

"The Abitibi volcano-plutonic belt forms the major portion of the Abitibi lithotectonic subprovince in the Superior Province. The Abitibi belt is composed essentially of"" (1) approximately 2.7 Ga old volcanic and sedimentary rocks; and (2) gabbro, tonalite, granodiorite and syenite intrusions occurring in well-defined prekinematic ( synvolcanic ), synkinematic and post-kinematic plutonic suites. Most of these rocks are metamorphosed to greenschist facies. Regional multi-phase deformation affects the volcano-sedimentary rocks. Deformation was initiated as these rocks were formed, and peaked at the end of the Keno ran orogeny with the emplacement of granitic batholiths.There are 145 former and current mines in the Quebec segment of the belt. To date, more than 420 Mt of ore have been extracted yielding 1,600 tonnesof Au, more than4,000 tonnesof Ag,4,400,000 tonnes of Cu and 5,300,000 tonnes of Zn. Mineral production is concentrated in geologic domains that approximately coincide with the boundaries of lithotectonic domains. We have compared the geology and mineral deposits of different domains to illustrate their distinct metallogenic signature. Certain domains are dominantly gold-producing (Cadillac-Malartic, Val-d'Or, Caopatina), others are base-metal producers (Matagami and Normetal), while others produce both gold and base metals ( Rouyn-Noranda, Chibougamau, Casa-Berardi-Joutel).Gold is extracted from quartz-rich vein deposits (for example, Val-d' Or), sulfide-rich veindeposits(Cadillac or Chibougamau) and from volcanogenic massive sulfide deposits ( Rouyn-Noranda). Base metals are generally mined from volcanogenic massive sulfide( RouynNoranda, Matagami, Normetal), although certain vein deposits yield base metals (Chibougamau) . Certain sectors are dominantly zincrich (Matagami, Normetal)."

Jan 1, 1989

By Michel Carreau

Presentation topic Introduction to Renewable Power in Remote Mining Industry Trend What are the Challenges and How to address them Acceptability (Management Buy-in) ? RP not core business to mining company Significant upfront costs Project Risks - Technological and Delivery Wind and solar power variability Operating hybrid power (Operator Buy-in) Conclusion Introduction ? RP at Remote Mining Sites Mining Project Cost Energy represents 25% of mining project CAPEX Energy represents 25% of OPEX Diesel, HFO, ? cost : 30+ cents/kWh RP - Proven technology - Excellent track record ?Wind (20 years), Solar PV (10+ years)? Hundreds of GW installed ?Reliable, High availability, very small OPEX. ?Wind/Solar cost : 15 to 22 cents/kWh (with good resource) ?Potential 10% to 20% Reduction in net cost of energy ?Price certainty for 20 to 25 years

May 1, 2013

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By Jirí Faltus

The paper deals with studying the impact of structural properties and anodizing of surface on the corrosion properties of extruded rods from commercial aluminium alloys: AA6082, AA6262, AA6012, AA2007 and new lead-free aluminium alloys AA6023, AA2015 and AA2111B. Samples were exposed to the corrosive atmosphere NSS, AASS in the chamber by EN ISO 9227. Surface of samples were either in the original state or anodizing by selected mode. The depth of corrosion attack and the form of corrosion attack are evaluated depending on the type of alloy, the metallurgical condition and surface treatment of the samples.

Jan 1, 2015

By P. K. Kaiser

3-D virtual reality (VR) visualization has opened new opportunities for complex 3D (x, y, z), 4D (x, y, z, t) or even nD data interpretation. The integration of common earth models (3D geologic data), mine models (3D excavations and stress), extraction models (1D time sequencing or mine sequencing) and nD monitoring data (e.g., seismic event parameters) into a common mining process model provides a platform for experts in various fields to better design, evaluate, monitor and modify mine plans throughout a mine?s life; from feasibility, through operation, to closure. Viewing seismic data in a stereoscopic VR environment within a mining process model offers data interpretation processes previously unavailable at lower dimensionality. MIRARCO has developed data analysis and viewing processes specifically designed to enhance microseismic and seismic data interpretation in a collaborative, immersive VR environment; bringing mine personnel and expert consultants together to evaluate data and make strategic decisions for cost effective and safe mining. Seismic events cause immediate hazards (rockbursts) and microseismicity causes gradual hazards through its cumulative effect in rockmass degradation. The focus of this paper is on understanding seismicity from a mine safety and mine planning perspective; in particular, how seismic migration patterns relate to the rockmass response to mining. The benefits of innovation in seismic data interpretation are significant, e.g., for hazardous work area identification, allowing better formulation of re-entry policies and workforce allocation planning, as well as allocation of effective support systems to strategic areas of elevated risk. Better understanding of the overall response of a mine to extraction also facilitates mine planning and design, assisting in reducing production costs and thus in enhancing profitability.

Apr 1, 2005

By Junto Nishiwaki, Shinji Kumai

"Mechanical and physical properties of the impact welded dissimilar metal joints are controlled by joint interface morphology. An intermediate layer (IML) is often formed at the joint interface and this deteriorates the interface quality in some metal combinations. Numerical and experimental studies were performed in order to examine the formation mechanism of the wavy interface and intermediate layer for explosive welded Al/Cu dissimilar metal joints. The impact welding process consists of (1) high-speed oblique collision of metal plates, (2) metal jet emission and large deformation and temperature increase at collision point and (3) rapid cooling at the joint interface. Euler-Lagrange coupling method, smooth particle hydrodynamic (SPH) method and modified laplacianFoam (LF) method were linked together to simulate a series of processes from (1) to (3), and the final interface morphology including the formation of IML was reproduced. The wavy morphology (wave-height, wavelength) and the position and composition of IML formed at the joint interface of Al/Cu joints were quantitatively in good agreement with those reproduced by numerical analysis. Our simulation results are useful for the control of the interface morphology, reduction of the amount of IML, and improvement of the mechanical properties of the impact welded dissimilar metal joints.INTRODUCTIONImpact welding is a kind of solid state joining method providing extremely high joint strength for both similar-and dissimilar metal combinations. Explosive welding and magnetic pulse welding are representative methods to achieve the impact welding. By a high-speed oblique collision between two metal plates, a metal jet is emitted from the collision point. The metal jet can remove any oxide films and contaminations on the plates and produce an active refreshed surface. Consequently, good metallurgical bonding can be achieved even for dissimilar metals (Crossland, 1982). Solid metals deform like fluids under the high pressure condition at the collision point and characteristic wavy interface is formed. In addition to the wavy interface, an intermediate layer (IML) is often formed at the joint interface in some metal combinations. Elimination or reduction of the amount of IML at the joint interface is desired since the excessive IML formation along the joint interface causes a large reduction in physical and mechanical properties. Formation of IML is considered to result from characteristic thermal history at the joint interface including partial melting due to the local temperature increase and successive rapid cooling behavior at the joint interface. In order to control the IML formation at the joint interface, it is necessary to reveal both heating and cooling processes at the joint interface. However, it is impossible to observe the phenomenon occurring at the joint interface and also difficult to investigate the temperature change at the joint interface directly during the impact welding. Therefore, simulation or numerical analysis is indispensable to overcome this problem. In the present study, the explosive welded Al/Cu joint, which is prone to form IML at the joint interface, was selected for the research. By using a newly developed numerical analysis method, not only the formation process of wavy interface, but also the local temperature increase and successive temperature decrease at the joint interface were reproduced. The formation process of IML was investigated by using both numerical analytic and experimental results."

Jan 1, 2018

By G. K. Lee, E. R. Mitchell

Designers of combustion processes may select aerodynamic conditions which produce only superfine fly ash. Although it is not usually anticipated that this will create a problem, such as has been found to agglomerate in high-velocity gas streams, to plug mechanical dust separators in a short time, and to contribute to atmospheric pollution. The problem is a fundamental one, and may be approached in several ways. The authors, in the course of their combustion research program, had occasion to examine the agglomeration of ash, ranging from sub-micron to 17 microns in size, produced in a (coal and oil) dual-fuel-fired steam generator. Several theories, supported by extensive laboratory studies, have provided some understanding of a probable mechanism of agglomeration. As a result, certain precautions are suggested in the design and selection of combustion processes and equipment.

Jan 1, 1962

By M. G. Mena, M. S. Mena-Junio

Silver (Ag) filler is the most attractive choice among all the conductive fillers of die attach materials for the attachment of silicon devices because of its balanced properties and relatively low cost. However, a major problem of silver is that it electrochemically migrates in the presence of moisture and applied bias. In microelectronic devices, silver migration can occur between adjacent conductors/electrodes, which leads to the formation of dendrites and eventually results in short-circuit failure. In order to assess the reliability of these conductive fillers, an investigation for two types of Agfilled die attach materials was done using the water drop test at room temperature and using a 1000 hour temperature-humidity-bias (THB) test under 85 ºC and 85% RH conditions. Four different bias/voltages and six different electrode distance spacing were used. Both dendrite and cloud/lace-like growths were observed as a result of the electrochemical migration of silver, Water drop test results revealed that increasing the applied bias/voltage and decreasing electrode spacing causes migration to occur faster, thus resulting into shorter time to fail (TTF). It was also observed that the growth rate of the dendrites from the cathode increased linearly as the dendrite approached the anode, probably due to a combination of increased ion availability and electric field. A minimum applied bias of 3 volts was required for migration to occur in Epoxy A as compared to 2 volts for Epoxy C. The higher migration voltage requirement for Epoxy A was attributed to the higher volume resistivity of the said epoxy. In addition to the minimum voltage requirement, it was observed that a minimum electric field of about 1 volt/mm is required for migration to occur. The 1000 hour THB testing did not result into any failures. It is surmised that the presence of condensed moisture is another requirement for migration. Such condition is not present during the THB testing.

Jan 1, 2012

By I. Le May

"The assessment of integrity in plants is discussed, together with the codes that are being developed for in service evaluation of engineering fitness for service. The use of Risk Based Inspection is described and some examples are provided of the evaluation of in service components in which flaws have been detected. An example of the assessment of the structure of a mine processing facility is described, and application of Risk Based Inspection and plant assessment procedures to mines is discussed. Periodic assessment of large plants and components to determine their integrity for continued safe operation is becoming a more accepted approach than formerly when regular shutdowns were the normal practice. This is on the way to becoming the preferred procedure for petrochemical plants and power generating plants, and the same philosophy is appropriate for many mining operations. Both the American Petroleum Institute (API) and the American Society of Mechanical Engineers (ASME) have committees developing codes for the continued operation of equipment as distinct from the existing design codes. The philosophy is one of risk-based inspection, which can be on a purely qualitative basis or more quantitatively based.The purpose is to reduce the inspection of unnecessary and non-critical items and to concentrate on the most critical components, reducing costs and downtime and increasing safety. The approach differs from that considered by many maintenance engineers, in that defects that are identified during an integrity evaluation do not automatically cause a component or structure to be condemned or require that repairs are made right away. The seriousness of the defect must be considered and the safe operating life can be estimated before it becomes necessary to replace or repair the unit or component. This is no different from what is done today with passenger aircraft and, to an increasing extent, with pressure vessels, reactor vessels and similar components in the petrochemical and power generating industries."

Jan 1, 1998

By G. W. Poling

This paper evaluates current environmental protection legislation, guidelines and criteria, focusing mainly on the land and water disposal of mill tailings. Effluent criteria and regulatory mechanisms are proposed, and submarine tailing disposal is discussed at length. The importance of basing regulations on the best available rationale is stressed.

Jan 1, 1979

By R. M. Kleine

In the fall of 1968, Sheridan Geophysics leased the Renzy Mine property 50 miles northwest of the town of Maniwaki, Quebec. A 500-tpd flotation mill was dismantled at Belleterre, Quebec, trucked into the mine over a winter road and re-erected during extreme winter conditions. Approximately one billion gallons of water were removed from Renzy lake to expose the orebody. A 3,000-hp diesel generating plant and a self-supporting community were set up during the early part of 1969. This was a remark-able achievement considering that most of the work, including the pouring of foundations and the draining of the lake, had to be done during the winter months. Despite this, the project was completed ahead of schedule and one million dollars below budget. The mill is now treating an average of 800 tpd.

Jan 1, 1970

By Burns Sutherland

Although some mine hoisting systems incorporating steel wire ropes on drum hoists experience completely dependable performance on the hoist ropes for many years, other rope records illustrate an erratic behaviour pattern and, as such, become a source of concern to the operator. This paper describes the causes of the difficulties most commonly encountered and incorporates methods of providing preventative or corrective maintenance. When such a program is utilized wisely, within the allowable limits of shaft time available, it can be the means of avoiding many unforeseen circum-stances and of reducing operating costs, as well as rope costs, to a mini-mum.

Jan 1, 1970

By D. M. Richards

"IntroductionThe Highland Valley Copper partnership was formed in July 1986 as a logical result of a mine with a large ore reserve but a small mill, and a mine with a large, modern mill but dwindling ore reserves. The original partnership of Cominco and Rio Algom was expanded in January 1988 to include Highmont Mining Company. During 1988/89 the Highmont mill was moved 7.5 km to adjoin the Lornex mill, becoming the Highland mill in the process, with a nominal capacity of 130 000 tonnes per day.The mine is located near the town of Logan Lake, 220 km northeast of Vancouver, British Columbia and 55 km southwest of Kamloops. The map in Figure 1 shows the general area. Kamloops is a major service centre and is served by two railways, two major roads and a regional airport. The mine site is situated between 1200 m and 1600 m above sea level on the Thompson Plateau. Principle activities in the area, in addition to mining, are cattle ranching and forestry. Ore reserves at the beginning of 1996 totaled 533 million tonnes at a grade of 0.42% copper and 0.008% molybdenum. Ore is mined from two pits — Valley, 3 km northwest of the mill; and Lornex, 1 km southwest of the mill. With 78% of the reserves, the Valley pit is the focus of activity.In order for Highland Valley Copper to remain competitive with a very low grade ore reserve, it has been necessary throughout the mine’s life for new technologies to be embraced as they become available. These have included such diverse technologies as in-pit crushing and conveying, large mechanical drive trucks, computerized truck dispatch and oneman survey instruments. During the next few years, it is planned to introduce two further technologies that are relatively new to both the world at large and the mining industry in particular. These are namely Global Positioning Systems (GPS) and Geographical Information Systems (GIS), both of which are expected to have a major impact on the way mining is carried out in the years to come."

Jan 1, 1997

By P. H. Willis

Since the 14th CMMI conference, held in Edinburgh in 1990, at which a paper was presented by the author (Willis, 1990) reviewing the role of integrating new technology as a survival strategy for South African gold mines, considerable change has occurred in the South African mining industry. This paper reviews the current state of the industry and provides an update on the technologies discussed ten years ago. It reviews available technology and provides a broad economic assessment of these technologies if they were to be introduced in an integrated mining system with a focus on deep level mining below 3000 m. It also reviews possible future technologies currently being researched and developed by CSIR: Division of Mining Technology (Miningtek).

Jan 1, 2000

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By Ahmad Ghahremaninezhad, Rebecca Radzinski

Arsenic is a highly toxic compound that is naturally found in the environment and is released through the processing of sulphide minerals. Arsenate (As5+) is less toxic than arsenite (As3+) and is soluble in water but can form insoluble precipitates when metal ions are present. The arsenic removal processes used in industry assume that arsenic is in its pentavalent state. Hydrogen peroxide can be employed to oxidize arsenite; however, it is expensive. It has been shown that activated carbon can be used to catalyze the oxidation of arsenite with oxygen as the only consumed reagent at ambient conditions with an efficiency of 99% in less than 24 hours. The mechanism which oxidizes arsenite is not yet understood; however, this study shows that a strong oxidizing agent is formed in-situ. The species and amount of oxidant formed were determined via iodimetric titration and electrochemical methods. The production of oxidant was optimized by comparing the amount of oxidant formed in-situ to the relative amount of arsenite oxidized.

Jan 1, 2015

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941