Search Documents

By John Wightman

LOCATION OF PROPERTY THE property of Caribou Gold Mines, Limited, is situated in the north-eastern part of Halifax county, seven miles south of the Canadian National railway line at Upper Musquodoboit. Approach to the village is by a secondary road, improved recently by waste rock from the mine dump. A two-wire telephone line, seven miles long, built and owned by the present operators, provides communication to the nearest telephone exchange, Parker's Corner. HISTORY In 1870, the Caribou area was recognized as a proclaimed gold district. From then on, operations were intermittent, with periods of considerable activity by small companies until there were no fewer than seven mines in a district two miles long by three-quarters of a mile wide. These were the Holman, Truro, Caffrey, MacDonald or Elk, Lake, Dixon, and Hilchey properties, all of which have had separate stamp-mills, and have produced gold for varying periods. Depths of the workings range from 100 feet to 1,000 feet. Power was generated at each property by means of steam boilers. At the present time, the Consolidated Mining and Smelting Company of Canada, Limited, controls all the leased areas, approximately 800 acres, and is operating by means of one central vertical shaft. GEOLOGY The district in and about Caribou Mines has an elevation of approximately five hundred feet above sea level. The area is fairly well wooded, with rock outcrops here and there. These outcrops, along with information from test-pits and shafts, have been the basis for the very excellent geological map of the district prepared by E. R. Faribault some years ago. The rock structure, which is one of the best examples in Nova Scotia of an elliptical dome, has its anticlinal axis in a northeast-southwest direction, and flat plunges in the same directions.

Jan 1, 1938

By M. Abumiya, N. Onodera

"The synthesis of large scorodite particles in non-ferrous metallurgical industries usually requires a high-cost operation involving heating and high-pressure autoclaving. To overcome these obstacles, an atmospheric-pressure process for scorodite synthesis (DMSP®) was developed, in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. This process gives scorodite of good crystallinity with particle sizes as large as 15-20 µm. The solutions used for scorodite synthesis in the DMSP® are prepared from various residues containing arsenic from non-ferrous smelters. The solutions may be contaminated with Cu, Sb, and Bi, for example, and therefore the effects of such impurities on the formation of crystalline scorodite need to be investigated. In this study, the effects of Cu, Sb, and Bi contaminants on the formation behaviors of scorodite particles in the DMSP® were investigated systematically.INTRODUCTIONThe synthesis of crystalline scorodite (FeAsO4·2H2O) is a suitable method for arsenic (As) stabilization and storage of As-containing by-products such as flue gas dusts in non-ferrous smelters. It is expected that the formation of large, highly-crystalline scorodite particles would be an ideal method for avoiding the release of arsenic to the environment. Generally, autoclave methods under pressurized oxidation conditions at temperatures above 100°C have been used for the formation of arsenic minerals such as scorodite. However, the autoclave method requires sealed vessels that are resistant to high pressure, heat and acids. This process is also unfavorable on account of the high construction expenses, and high running costs as a result of vapor heat loss. Processes for synthesizing scorodite under atmospheric conditions at temperatures below 100°C which do not need an autoclave have therefore been extensively investigated (Demopoulos, Droppert, & VanWeert, 1994; Demopoulos, 1996; Demopoulos, Lagno, Wang, & Singhania, 2003; Droppert, Demopoulos, & Harris, 1996; Filippou & Demopoulos, 1997).Recently, Fujita et al. (Fujita, Taguchi, Abumiya, Matsumoto, Shibata, & Nakamura, 2008a, 2008b, 2009; Fujita, Taguchi, Kubo, Shibata, & Nakamura, 2009; Fujita, Taguchi, Shibata, & Nakamura, 2009) developed a new method for producing large scorodite crystalline particles with improved filtration and washability properties at normal atmospheric pressure and temperatures below 100°C. In the new method, oxygen gas (O2) is blown into solutions containing a high concentration of arsenic ions (As(V)) and ferrous ions (Fe(II)). The Fe(II) ions were subsequently oxidized to ferric ions (Fe(III)), resulting in the formation of large scorodite particles. High supersaturation of solutes such as Fe(III) will result in excessive nucleation, and the formation of poorly crystalline phases. The scorodite formation must therefore be conducted in a manner that avoids the critical supersaturation level being exceeded. It is supposed that the oxidation of Fe(II) to Fe(III) by O2 gas in the new method suppressed the supersaturation of Fe(III) during scorodite formation. The low Fe(III) supersaturation resulted in formations of highly crystalline scorodite particles of size of around 20 µm. In June 2008, based on the developed process described above, DOWA began experiments to verify the industrial capability of a plant with a capacity of 30 MT/month of As. It was successfully proven that it is possible to produce crystalline scorodite industrially on a commercial scale. This process was named and trademarked as DMSP® (Kubo, Abumiya, & Matsumoto, 2010)."

Jan 1, 2012

By Luino Jr. Dell'osso, Richard L. Every

The enormity of the methane-in-coal problem is discussed, with a brief summary of the state-of-the-art. Laboratory techniques and data on the desorption of methane from Pittsburgh seam coal are presented and discussed and include the effect of time, temperature and vacuum. Under laboratory conditions, it was possible to displace 90 per cent of the residual methane by flooding the coal samples with carbon dioxide. Carbon dioxide was found to be three times more effective than air and almost five times more effective than helium.

Jan 1, 1972

By A. A. el-Geassy, A. A. el-Tawil, Hesham M. Ahmed, Bo Bjorkman

The Iron and steel industry is one of the most intensive energy consuming processes. The majority of iron making processes is now directed towards the uses of fossil-based energy sources like coke, coal and oil. Recently, emphasis has been paid to replace part of fossil- based energy sources with renewable biomass-derived reducing agents. In the present work, the possibility of the effective use of woody biomass in carbon-iron oxide composites was investigated. Wood powder was carbonized in N2 atmosphere at 300 up to 450oC. The carbon content in the produced bio-char increased with temperature. The porosity of the char arises from maintaining the cellular structure inherent in wood biomass increases with temperature. The reduction behavior of four iron oxide-bio char composites having different fixed carbon content were carried out non-isothermally up to 1200oC in Ar atmosphere using thermogravimetric anlyser (TGA). Quadruple mass spectroscopy (QMS) was also adopted to measure the CO, CO2 concentrations in the off gases resulted during reduction process. The effect of volatile matter on the reduction of iron oxide was intensively studied. The different phases developed in the reduced product were identified by X-ray diffraction (XRD). The reduction of composites was found to proceed in a stepwise manner (Fe2O3?Fe3O4?FexO?Fe).

Jan 1, 2015

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By Nicholas C. Williams

This paper presents the development of a demand reduction and responsive strategy capable of reducing the electrical power demand, particularly during peak conditions. The work presented includes a case study of a UK colliery. Areas explained are the equipment installation at the mine; the development of the demand reduction strategy including the load profile database and prediction optimisation model. Some live production data from the power meter installation at the mine is also presented.

Aug 1, 2013

By D. M. Ziebarth

"Normal sequence of operations to develop a new underground mine is: construct and outfit headframe for shaft sinking, sink shaft, construct and outfit shaft sump, develop shaft station and shaft bottom steel. In an effort to reduce the overall project schedule, an innovative plan was developed to install service shaft steel below station level, prior to the completion of the shaft sinking effort. To better evaluate the construction of this substantial steel tower, a preliminary constructability evaluation was conducted, including the best method of supporting the main tower; from the bottom, middle or top of the tower. The design criteria and plan involved: •,Develop access from existing service shaft, 25 km underground •,Use of materials to maximize strength while minimizing corrosion exposure •,Estimating the location of the shaft centerline •,Over excavating the station and shaft below station to allow future shaft steel repositioning •,Designing the tower steel for modular installation •,Incorporate commissioning considerations, such as suspension of the cheese weights during steel installation •,Provision for covered stair access to shaft bottom •,Enclosed shaft envelope with open panels to allow visibility and ventilation The design approach was innovative and this paper will describe the design principles and challenges encountered while providing insight into the solutions developed and implemented; especially the modular construction and installation methodology. INTRODUCTION In an effort to expand the mining operations, a plan was developed to construct a new service shaft closer to the new mine workings and convert the existing service shaft to a production shaft at the Potash Corporation of Saskatchewan Inc. (PCS now Nutrien) Rocanville Potash mine in southeast Saskatchewan. The new service shaft required a multi roped friction hoist operating a cage / counterweight, rope guided conveyances to support the operational requirements. The service shaft is an integral part of the mining infrastructure as it provides access to the underground workings, transport personnel and materials underground for operation and maintenance of the mine. The shaft also allows for services required for safe operation of the underground mine, power supply, controls, communication, dewatering and fresh water supply."

Jan 1, 2019

By A. I. A. Salama, M. W. Mikhail

"A comprehensive software package has been developed at the Western Research Centre to meet many of the coal preparation requirements in the Canadian coal industry. This package performs three main functions: (1) data handling and manipulation; (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modelling, evaluation of density and size partition characteristics, and attrition curves; and (3) graphics output.The software described in this paper is potentially a valuable tool for coal preparation plant engineers and operators for evaluating process performance and adjusting plant density separator cutpoints. Moreover, the analytical laboratory technician could find this package very useful in manipulating and presenting laboratory results."

Jan 1, 1997

By L Gill

The four basic types of electric motors -squirrel-cage, wound rotor, synchronous and D.C. -are de-scribed, with particular reference to speed-torque characteristics. The three classifications of squirrel-cage motors, C.E.M.A. B, C and D, are compared, and methods of selection for specific drives are outlined. Wound rotor and synchronous motors are covered from the viewpoint of construction details, methods of operation and control required. The application of these motors to crushers, conveyors and ball mills is described and reasons for their selection are given. The application of D.C. motors to haulage equipment and mine hoist drives is included, and the basic principles of a variable voltage drive are illustrated. Efforts have been made through-out to provide specific examples of motor selection, with particular reference to the mining industry. THIS paper will attempt to answer the question -"which motor should be used for a specific drive?" Although it is impossible to cover the complete subject of electric motor application here, we hope to give some idea of the types of motors available and why certain types are used on specific applications.

Jan 1, 1963

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By Brian L. Beninger

This paper discusses the application of the computer to coal preparation process predictions. In broad terms, the computer is used to perform two main functions. Firstly, the given float-sink analysis is interpolated and extrapolated to cover the entire actual range of raw coal specific gravity. Assumptions based on historical data must be made at times. Secondly, the partition curve, which, from historical data, defines the efficiency of a specific coal washing process, is applied to the washability data in order to determine the expected clean coal yield and quality. The vast amount of numerical work which is required to make a prediction of this type exhibits the need for computer methods in this area.

Jan 1, 1979

By Rita Awwad

Building Information Modeling (BIM) has been gaining a significant edge in the construction industry over the last decade. BIM allows gathering all building information in one shared database that can help all construction entities better understand, integrate and visualize all work progress from inception to operation of the building. The main purpose behind BIM is to bring all project participants together (Client, Architect, Contractor, Consultant) since the initial stages of a project allowing them to cooperate and work as a team in the promise of an increased productivity, reduced cost, enhanced quality and faster delivery. However, a full-fledged implementation of BIM tools and benefits is not yet achieved in the construction industry and remains a debatable issue for researchers and practitioners in the construction field. This paper aims at assessing BIM awareness and usage in the Lebanese construction industry through conducting interviews with contractors, architects and consultants that are key players in the Lebanese market. A comprehensive literature review about BIM adoption in some developed countries and in the surrounding region is also provided in order to better evaluate the Lebanese industry status in comparison with foreign industries. This research sheds the light on BIM awareness of the different construction parties in the Lebanese market, assesses the extent of its current use, identifies the pertaining implementation challenges, and provides recommendations to enhance BIM role in the Lebanese construction industry.

Aug 1, 2013

"The technical report form provides the headings to be used and content required when a completing a technical report to be filed in accordance with NI 43-101. The technical report is meant to be a summary of the scientific and technical information on the mineral property. The Instrument (NI 43-101) requires that technical reports be filed with Canadian provincial or territorial securities regulators to support certain disclosure of mineral exploration, development and production activities and results in order to permit the public and analysts to have access to information that will assist them in making investment decisions and recommendations. FORM 43-101F1 TECHNICAL REPORT INSTRUCTIONS (1) The objective of the technical report is to provide a summary of scientific and technical information concerning mineral exploration, development and production activities on a mineral property that is material to an issuer.This Form sets out specific requirements for the preparation and contents of a technical report. (2) Terms used in this Form that are defined or interpreted in National Instrument 43-101 Standards of Disclosure for Mineral Projects (the “Instrument”) will bear that definition or interpretation. In addition, a general definitioninstrument has been adopted as National Instrument 14-101 Definitions that contains definitions of certain terms used in more than one national instrument. Readers of this Form should review both these national instruments for defined terms.(3) The qualified person preparing the technical report must use all of the headings of the items in this Formandmay create sub-headings. If unique or infrequently used technical terms are required, clear and concise explanations must be included. (4) No disclosure need be given in respect of inapplicable items and, unless otherwise required by this Form,negative answers to itemsmay be omitted. Disclosure included under one heading is not required to berepeated under another heading. (5) The technical report is not required to include the information required in Items 6 through 11 of this Form tothe extent that the required information has been previously filed in a technical report for the property being reported on, the previous technical report is referred to in the technical report and there has not been any material change in the information. (6) The technical report for development properties and production properties may summarize the information required in the items of this Form, except for Item 25, provided that the summary includes the materialinformation necessary to understand the project at its current stage of development or production. (7) The technical report may only contain disclaimers that are in accordancewith section 6.4 of the Instrument and Item 5 of this Form."

Jan 1, 2003

By M. Kane, B. Bissonnette, D. Hodouin

"A laboratory cell has been designed for a careful investigation of gold ore cyanidation using mathematical modelling of the process kinetics. The cell is a stirred vessel with continuous monitoring and control of pH, oxygen and free cyanide contents. Samples are automatically extracted for gold analysis. The instruments are connected to a microcomputer which records all the measured variables and calculates the reagent consumption (air or oxygen, cyanide, lime). For cyanide control a sample is automatically extracted and filtered and the solution analyzed, using a specific electrode, by a flow injection technique. The rate of gold dissolution is modelled using a kinetic model the parameters of which are calculated by a non linear least-squares technique. The parameters of an empirical model of reagent consumption are also estimated. The resulting model is used in a simulator for gold cyanidation plant design, tuning and control.INTRODUCTIONThe leaching of gold ores in a cyanide solution is the usual method for gold extraction from raw ores. This process requires long reaction times and leads to very significant consumption of cyanide. The optimization of the cyanidation plant operation is a very important aspect of gold ore processing for increasing gold recovery and decreasing operating costs. The key parameters to the improvement of gold extraction are the selection of an efficient solution chemistry, the design of the size and the arrangement of the equipment and the correct tuning of the operating variables. Automatic control strategies can then be applied to maintain industrial operations at their optimum setpoints.Two approaches can be used for optimizing design and control of cyanidation circuits, either empirical trials for improving process performances or mathematical modelling of the process kinetics for subsequent analysis, simulation and optimization. The advantages of the second approach, which is used in this study, is that it gives a systematic pattern to interpret data and reliable tools, in as much as the models are good, to improve operation performances. In order to determine the structure and the coefficients of cyanidation models, well controlled measurement and calibration procedures must be used. The purpose of the paper is to present an equipment and a test procedure for modelling the kinetics of gold ore cyanidation."

Jan 1, 1990

By J. P. Norrie

The presence of copper-bearing rocks in the Coppermine River area of Arctic Canada has long been known. Word of this was probably circulated along the Arctic and Hudson Bay coasts by the Eskimo, who no doubt traded articles made from native copper among themselves. It is not known whether any of these ever reached the southern shores of Hudson bay. The Indians, also, knew of the occurrence of copper here, as they served as guides to Hearne when he made a successful trip over land from Hudson bay to the Coppermine river. The possible commercial importance of these copper deposits was early appreciated by the Hudson's Bay Company, who on December 7th, 1770, despatched Samuel Hearne from Fort Prince of Wales, now Fort Churchill, to investigate them. He reached the then unnamed river at a point forty miles from its mouth on July 14th, 1771, and after surveying the river to its mouth and naming it the Coppermine, he retraced his steps to Fort Churchill by an overland route. Hearne's expedition was probably the most remarkable and arduous ever attempted in Arctic exploration, but the actual value derived from the trip was entirely out of proportion with the hardships he must have suffered. He verified the occurrence of native copper, but his astronomical and other observations were of little value. Until 1912 no concerted effort was made to obtain any definite information as to the geology and economic value of the Copper-mine deposits.

Jan 1, 1931

By V. V. Pankov, W. R. Chen, L. R. Zhao

Diffusion nickel aluminide and overlay NiCrAlY coatings were deposited on single crystal Ni-base superalloy CMSX-4 substrate using the chemical vapour deposition and cathodic arc evaporation techniques, respectively. The NiCrAlY coating underwent a post-deposition heat treatment in an argon atmosphere at 1100°C for 2 hours. All the coated specimens were subjected to furnace cyclic oxidation testing at 1000°C up to 1500 one-hour cycles. The morphology, elemental composition and phase constituents of the oxide scales formed on the coating surface were analyzed using scanning electron microscopy, energy-dispersive spectroscopy and X-ray diffraction. It was observed that the diffusion aluminide coating experienced accelerated weight gain at an early stage of the test (150-400 cycles), whereas the overlay NiCrAlY coating fabricated by cathodic arc evaporation maintained steady-state weight gain throughout the entire 1500 cycle test duration. This difference in oxidation behaviour between the two types of coatings is attributed to the early development of nickel-aluminum spinel on the surface of the diffusion aluminide coating, in contrast to the stable aluminum oxide scale formed on the overlay NiCrAlY coating during cyclic oxidation testing.

Jan 1, 2015

By H. Watari

In 1998, a voluntary agreement was reached between the European Commission and the European Car Manufacturers Association (ACEA) to reduce average carbon dioxide emissions of new cars to 25% below 1995 levels by 2008, Agreements have also been reached between the European Commission and the Japanese Automobile Manufacturers Association (JAMA) and the Korean Automobile Manufacturers Association (KAMA), However, the target average of carbon dioxide emissions of less than 140g/km in 2008 is a very challenging goal, Therefore, total product weight reduction is an objective for many manufacturers, This can be achieved utilizing materials possessing high strength and low weight, One material that has recently attracted interest is magnesium alloys, The magnesium alloys are expected to play an important role as next-generation materials, which have possibilities of contributing to lighten the total product weight when magnesium products can be used to replace aluminum and mild steel products.

Jan 1, 2005

By P. O. Sandvik, George Erdosh

"AbstractThe Cargill phosphate deposit, located 32 kilometers southwest of Kapuskasing, Ontario, was discovered by the Resource Development Group of International Minerals & Chemical Corporation in 1975 and has been evaluated through an extensive program of 190 drill holes, numerous chemical analyses, metallurgical tests, and engineering and economic studies.The Cargill alkalic complex, comprising principally car-bonatite and pyroxenite-amphibolite rocks, was intruded in to the rift system of the Kapuskasing High during late Precambrian time about 1,800 million year s ago, near the intersection of northeast- and northwest- trending faults. The Cargill complex is one of at least ten known alkalic complexes in or close to the Kapuskasing magnetic-gravity-high system and is expressed by an elongated, northeast- oriented, three-part magnetic anomaly 7.2 kilometers long by 2.8 kilometers wide . Weathering and leaching under assumed temperate to cool, moist climatic conditions , and controlled by faulting, shearing and/or initial petrographic variations within the carbonatite , developed a small, locally confined karst system in the car bonatite rocks and resulted in a thick enriched leached carbonatite zone, capped by troughs and sinks, filled with a residuum of apatite, goethite, clay and other minerals stable in the near -surface, oxidizing environment. Overburden is 5 to 165 meters thick."

Jan 1, 1977

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By P. F. Venus

In December 1977, a large pillar was removed by blasthole mining methods at lnco's Creighton No. 3 mine. Although the 2,363.000-ton blast was not a size record for a single underground blast at Inco, it did represent a significant departure from conventional blasthole mining. In terms of the application of nominal 6-inch-diameter boreholes underground, coupled with bulk slurry explosives, the magnitude of the blast is considered a first and very important development. The application of large-diameter boreholes in underground operations was first tried successfully in 1973. Since that time over 13/4 million feet have been drilled in this adaptation of an open-pit technique to underground operations. The blast, which required 708 holes, totalling 131,500 feet of drilling, was loaded in a six-week period, using special slurry handling techniques developed jointly by Inco and CIL. Inco operating and engineering personnel consider this application of large boreholes and slurry explosives for blasthole mining a very important milestone in modern mining technology.

Jan 1, 1978