Search Documents

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By P. Taskinen, D. Lindberg, H. Viitala

The formation of copper chlorides in flue dust or deposits in heat recovery boiler of copper smelters or waste-fired boilers may lead to formation of corrosive partially molten deposits on walls and heat exchangers of the boilers. These deposits can contain various other metals, such as alkalis, Fe, Zn, Pb together with oxides and sulfates. In the present study, a thermodynamic model for copper-containing binary and ternary metal chloride systems within multicomponent CuCl-CuCl2-FeCl2-FeCl3- PbCl2-ZnCl2 system has been assessed and optimized based on own experimental phase equilibrium data, as well as literature data. The thermodynamic properties of the liquid phase was modelled using the quasichemical quadruplet model and a thermodynamic database was optimized to predict all available experimental data within the experimental error limits. The thermodynamic database allows for more accurate predictions of potential corrosion-related issues in various heat recovery boilers and waste-fired boilers due to formation of copper chlorides. INTRODUCTION In the copper flash smelting, flue dust can cause severe problems in the gas train, used for separating dust from the SO2-rich off gas, by forming corroding accretions on the walls of the heat recovery boiler. Formation of dust build-ups in the boiler need to be cleaned regularly and potential corrosion damage checked, requiring costly and unscheduled shutdowns of the flash smelting process. Compounds of copper and zinc among other elements having high vapour pressures may volatilize during the smelting of the copper concentrate, forming dust when the process gas cools down. Also, particles of solid or liquid iron oxides originating from the ore get transported with process gas to the heat recovery boiler as a result of entrainment in the flue gas (Miettinen, 2008) The dust deposit build-ups on the boiler walls are formed partly by direct impact of particles and partly by vapour condensation on the boiler walls. The initial deposition takes place by the condensation of vapours that contain zinc, lead, arsenic and other metals having high vapour pressures. Also, low melting point eutectic components of alkali salts such as chlorides and sulphates can act as sticky cohesive particles attaching to the boiler walls. The fine particles landing on the surface of the porous dust deposit layer react in the SO2-rich atmosphere of the boiler to sulphates. The process gas within the boiler contains SO2, O2, SO3, H2O and N2 that diffuse into the porous accretions to form a stagnant gas layer within the dust deposit structure. The composition of this gas layer may differ greatly from the composition of the process gas that is flowing on the surface of the accretion layer. Locally HCl and H2SO4 are formed and even a reducing atmosphere may exist within the dust deposit layer, allowing new reactions to take place. The local micro-atmosphere may enable metal sulphates to be reduced to secondary sulphides and even metallic components. Within the accretion layer, components may be formed that would not be stable in the gas atmosphere inside the boiler (Miettinen, 2008). This may be the mechanism by which for instance chlorides of Cu, Fe and Zn are formed within the deposit layer.

Jan 1, 2019

By M. H. Moys, J. A. Engelbrecht

"Large-diameter flotation columns are subject to severe axial mixing which has reduced column recovery and has generally limited it to cleaner applications. It has been assumed that columns with diameter greater than 1 m should be baffled to reduce axial mixing, but little work has been reported quantifying the effectiveness of baffling. Tests were done on a 0.2 m by 2 m column fitted with baffles of different geometry. It was generally found that the inclusion of baffles in the column worsened rather than improved mixing conditions in the column. This is explained in terms of a model for the effect of poor gas distribution on the behaviour of the column; this showed that under typical conditions a 16% excess of gas flux in the one compartment of a two-compartment column could result in one of the compartments being ""dead"" (i.e. with no net flow of slurry through it), resulting in a substantial loss of performance. The quality of mixing in the laboratory column was only reliably improved when the baffle was raised so that its top was positioned above the froth-slurry interface level. It should be possible to increase column recovery substantially with this configuration. The improved residence time distribution also means that columns can be used more effectively in roughing and scavenging applications. IntroductionFlotation columns have generally been used in cleaner applications, starting with their dramatic success at Mines Gaspe(1). Their lack of applications as roughers and scavengers is probably due to their poor residence time distribution (RID) when compared to the conventional cells they would replace. Espinosa-Gomez et al,(2) recently used them in rougher applications but installed three columns in series, presumably to cope with this disadvantage.Dobby and Finch in their seminal papersl(3,4) on the scale-up of flotation columns were the first to quantify the impact of axial mixing on the performance of industrial flotation columns. Laplante et al.(5) collected further data from the literature for column diameter D, ranging between 5 cm and 183 cm, gas superficial velocity Jg ranging between 0.7 cm/s and 2.8 cm/s and per cent solids in the feed S ranging between 3% and 52%. These data were analyzed with reference to the axial mixing model using the boundary conditions for closed vessels (the latter are more appropriate for flotation columns but the model is more difficult to use because analytical solutions for the RID are not available). The data were correlated by:"

Jan 1, 1993

By A. Bouchard

"Based on laboratory testwork, a two-stage cleaner / re-cleaner circuit with feed regrind was proposed to replace an existing single-stage middling circuit treating a scavenger concentrate at Inco’s Clarabelle mill. In order to effectively transfer the technology and implement the new flowsheet in the plant, an extensive on-site pilot plant campaign was conducted. After demonstrating the improved metallurgy, the two-stage middlings circuit was successfully implemented at the operation.The present paper describes the on-site pilot plant testwork and the plant metallurgical improvement after implementation of the new middlings circuit. The addition of TETA / Na2S03 greatly enhanced the pentlandite selectivity against pyrrhotite and the two-stage cleaning considerably improved the pentlandite selectivity against rock minerals. The improvement was immediate after the installation of the new middlings circuit. Size by size recovery analysis indicated that a finer regrind would further improve the metallurgy of the new two-stage cleanerhe-cleaner circuit and those modifications are in progress at the mill.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill has been described elsewhere (Kerr and Kipkie, 1985; Agar, 1991). While maximizing the recoveries of chalcopyrite (Cp) and pentlandite (Pn), continuous effort has been directed toward improving pyrrhotite (Po) and rock minerals (Rk) rejection. Inco discovered diethylene triamine (DETA) and triethylene triamine (TETA) (Marticorena, et al., 1994) for pyrrhotite rejection. Falconbridge further improved pyrrhotite rejection using DETA and SO2 (Kelebek, et al., 1995). No special technologies are used in the rejection of rock minerals."

Jan 1, 2001

By R. W. Diamond

PUBLIC debts, and the policies guiding public finance in Canada today, are in such a state that every intelligent citizen should be familiar with them, and should be concerned about them. None of you have robe reminded that taxes have already risen to a point where they both annoy and hurt you, but they should also alarm you; alarm you, not so much because of the taxation, but because of the mounting expenditures represented by that taxation. I have no hesitation, therefore, in presenting a paper dealing with public finance at a meeting of the Mining Institute, since all present are concerned,. both as individuals and as representatives of the industry. Moreover, it is important that engineers, particularly, should become better acquainted with the interlocking relationships of economics, public finance, government, and technology. While I am neither an economist, a tax expert, nor a chartered accountant, I shall try to tell you, from my viewpoint as an engineer and an interested voter, the story of public finance in Canada today and of certain causes and effects, and I shall venture certain conclusions. In doing so I may merit criticism by experts, but I will risk this in the hope that sufficient interest will be stimulated in the subject to persuade you, as individuals and as groups, to advance, or to institute, your own studies in public finance, and in turn to interest others. I hope that some of the ideas which will be expressed, or which may develop, will bear fruit. I fully realize that several eminently qualified men have spoken on this subject during recent months, and that many authoritative articles have been written. However, I approach it with confidence, because I propose speaking to you not as an authority, bur as one of you, having similar interests and similar engineering knowledge, who only a few months ago became particularly interested in the subject, studied it, and who now sets before you a summary of his findings, with the conviction that the situation is so serious that constructive planning and constructive action by all thinking citizens are imperative.

Jan 1, 1939

By T L. Horsley

This paper deals with the drilling and blasting methods employed at the Cassiar mine, which is located just south of the B.C.-Yukon border. It covers both the "pit" and "peak" mining operations. Specific problems, such as working in frozen ground, are discussed, and the breaking characteristics of the various rock formations are outlined. The paper concludes with a brief mention of the equipment used in the operation, as "~ell as an outline of the breaking costs. Introduction T HE Cassiar asbestos mine is located just south of the British Columbia -Yukon border high on a spur of McDame mountain. Chrysotile asbestos fibre occurs in a faulted enlargement of a serpentine sill lying conformably be-tween a series of sedimentary beds and volcanic flows which dip at 45 degrees into the mountain. One end of the orebody is eroded by a cirque in which a layer of permanently frozen ore and waste talus lies at the end of the mining benches. The topography at the mine is steep, with no flat areas. Roads, dumps, and areas for crushing,

Jan 1, 1965

By A. L. Mackie

Mine water from base metal mines is generally characterized as having high concentrations of heavy metals and low pH, resulting in the need for treatment prior to discharge to receiving waters. In this study, two high-rate clarification processes were evaluated at bench-scale: the high density sludge (HDS) process and sand-ballasted flocculation. High-rate clarification processes generate larger, denser flocs which settle more quickly than those formed in conventional flocculation processes. The HDS process uses recirculated sludge in order to seed floc formation, whereas ballasted flocculation uses microsand. Both of these high-rate processes require the addition of quicklime or hydrated lime to increase pH and allow for the formation of insoluble metal hydroxides, which can then be removed in the clarification stage. Previous research has shown that cement kiln dust (CKD) can effectively replace quicklime in conventional sedimentation processes for metals and acidity reduction to meet discharge guidelines (Mackie & Walsh 2012). CKD is an alkaline by-product of cement manufacture that has fine particle sizes and varying free lime concentrations depending on the manufacturing process. The lower solubility (i.e., free lime content) of CKD requires larger doses of material to be added to reach treatment pH targets for metals precipitation. The purpose of this study was to evaluate the treatment efficacy of high-rate clarification processes for mine water treatment, compared with conventional sedimentation, at bench-scale with conventional (i.e., lime) and novel (i.e., CKD) pH adjustment additives. Results of the study showed that all treatment processes (i.e., HDS, ballasted flocculation, and conventional sedimentation) were able to reduce target metal concentrations to well below Canadian guidelines (i.e., total zinc and total nickel < 0.5 mg/L, total copper < 0.3 mg/L) using either CKD or lime. Additionally, mine water samples treated with CKD generated lower sludge volumes than those treated with lime (i.e., 50 versus 100 mL for conventional sedimentation and 100 versus 200 mL for HDS) even with increased concentrations of solids introduced during treatment. This is most likely due to slower neutralization rates when using CKD, due to its lower solubility, as well as finer particle size. The sand-ballasted flocculation process was able to reduce final turbidity in CKD-treated samples while the HDS process did not when compared to conventional sedimentation, making the ballasted flocculation process preferable for reducing final solids concentrations in CKD-treated mine water.

Aug 1, 2013

By E. Michelotti, M. Cardu

This paper presents the results of a new method that has been tested to recover metallic cobalt lost by diamond beads from rock cuttings. When dimension stones are cut using diamond wire saws, the beads become worn and, before the end of their cycle life, lose a certain amount of material; this material is prevalently made up of sintered metal and diamonds. The material is then washed away, together with rock debris, in a dilute pulp. In effect, this process involves the dispersion of economically valuable, but potentially polluting, materials (such as cobalt) that are used to confer indispensable technological features to the beads. This current research aims to develop a waste-processing pilot plant (High-gradient Magnetic Separator or HGMS) to recover metallic components from the pulp by means of a suitable separation. The research\u2019s purposes are two-fold: a. to remove the polluting components from the rock debris before their disposal and b. to start a recycling process of the valuable metals.

Jan 1, 2010

By He Zhexiang

The settlement properties of tailings modified by flocculants were investigated at the Shizhuyuan Mine, with the aims to screen for the most effective flocculants and the optimum dosage rates for tailings sedimentation. The settlement rate was used as the indicator of effective tailings sedimentation. Calcareousness and three polyacrylamides (F1, F2 and F3) were selected for settlement property evaluation. The results proved that sole use of calcareousness or any of the polyacrylamides had no apparent effect on the tailings sedimentation, while a remarkable acceleration of sedimentation could be observed with a combined addition of calcareousness and polyacrylamides, among which the addition of polyacrylamide F2 together with calcareousness is the most effective. The optimum dosage rate of F2 and calcareousness is 50g/t and 3kg/t respectively. The density of tailings slurry has an effect on sedimentation at the early settlement stage, with lower density generating quicker initial settlement.

May 1, 2007

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By Guocheng Pan

"Although many factors play roles in the estimation of recoverable reserves, smoothing effect and conditional bias are considered major geostatistical issues in the estimation. This paper introduces measures for smoothing effect and conditional bias, and provides insights into their relation to the estimation of recoverable reserves. Both smoothing effect and conditional bias are intrinsic to the information effect and kriging estimators. For a given level of drilling information, however, it is possible to identify the optimal search radius that minimizes conditional bias. Furthermore, it is also feasible to define variance correction factor for reduction of the smoothing effect from exploration block models. Both of these components are key to the accurate estimation of recoverable reserves. IntroductionThe accurate estimation of recoverable reserves is critical to decision making in different phases of feasibility study and mine planning. Much attention for improving the methodology of estimation has been focussed on the effect of the change-of-support (Parker, 1980; Dagdelen, 1996). For example, it is essential to make a volume- variance correction to the estimate of multiple indicator kriging (Hoerger, 1992). When the size of block, b, in the geostatistical model differs from that of selective mining unit (SMU), v, a volume-variance correction is warranted for the prediction of recoverable reserves.Most mining plans and decisions are made prior to the availability of high density blast-hole samples. In most mining operations, the true SMU grade Zv is unknown at the time of selection. Instead, the selection is based on the estimate Z v**derived from high density blast-hole samples within the deposit G. Nevertheless, the estimate Z v * of recoverable reserves in the stage of mine planning is derived from exploration data. At the end, the production result must be reconciled to the estimate Z v * . In other words, the selection is based on Z v** from blast-hole samples, while the final production figures are reconciled to Z v * from exploration drilling. For a given preselected cutoff grade z0, the actual mining panels will consist of the units having the estimated grade Z v** =z0 rather than the true grade Zv =z0. The difference between Z v** and Zv is usually of less concern."

Jan 1, 1998

By Mel Torrie

1 Want access to low level vehicle data so 3rd party apps can be applied as desired 2 Hardware Agnostic (COTS plug and play) 3 Common/Open protocols that facilitate integration and the coexistence of a variety of applications on a variety of equipment 4 Minimum computer hardware footprint 5 Technology Independence (including comm. backbone)

May 1, 2013

By S. H. Logan

Mr. B. Neilly: A week or so ago the Secretary was good enough to forward me an advance copy of this paper by Mr. Logan and it was suggested that I comment on it at this meeting. At that time I was not very certain that I would be here, so I committed my thoughts to paper. As a matter of courtesy to Mr. Logan, I sent him a copy of my proposed remarks and I would like to give you just what I sent to him. Appreciating fully Mr. Logan&apos;s ability and many sources of information, one naturally hesitates to question anything seriously set forth as his considered opinion. Neither does one of my political stripe like to accuse him of being too &apos;conservative.? However, in places his paper reminds me of another general manager of a Canadian bank. While I was still Secretary of the Ontario Mining Association, this general manager wrote asking for our forecast on the current year&apos;s mineral production, stating that he proposed to refer to such production figures in his annual address to his shareholders. The request was considered very complimentary to the Ontario Mining Association and, in my opinion, justified a great deal of serious study and effort. Finally, the estimate was prepared and forwarded, showing a modest increase over the previous year&apos;s total. Picture our surprise and chagrin on reading his address to find that he predicted not an increase but, if you please, a decline of over $10,000,000. Before I cooled off I wrote asking the basis of such a prediction and got a reply to the effect that men in his position had to be ultra conservative in picturing the future.

Jan 1, 1931

By R. H. McCorkell

Measurements of radon in air and aqueous solutions can be affected by leakage from vessels in which samples and standards are kept and by absorption and later release of radon by the materials of these vessels. The author had received various oral communications concerning the se processes : e.g ., that natural rubber and greases absorb large amounts of radon, whereas silicone rubber and grease do not; and that radon is readily lost from polyethylene bottles and that inverting glass bottles containing aqueous samples reduced radon loss from them . However, the results of actual tests and quantitative data showing these effects were not available. For this reason, it was necessary to make numerous measurements of the leakage and absorption of radon in the course of designing apparatus and methods for measuring radium and radon concentrations. It was thought that the data obtained might be of use to others, and consequently they are compiled in the present note .

Jan 1, 1980

By J. Zinck

The management of mine wastes generated by both active and inactive mining is an ever more challenging issue. The cost to manage and treat mine wastes, including tailings, waste rock, treatment sludge and slag, is estimated at over $50B in Canada and the United States alone. Cost-effective technologies are required to meet both short and long term challenges and increasing environmental standards. This paper will provide an overview of novel and conventional technologies to manage mine waste particularly in the areas of waste stabilization, treatment and disposal technologies.

Jan 1, 2004

By Thomas. Lisa, Mark Coleman

Schenck Process is an established customer-driven solutions provider, utilising its knowledge, expertise and technologies to transform production processes. Operating across several industries Schenck Process have developed quality solutions from their range of equipment to solve problems and fill holes in other people’s processes. In the non-ferrous metals industries Schenck Process have been using their Clyde Brand solutions in Pneumatic Transport to solve problems on smelter sites for a number of years, handling of concentrates, additives and metallurgical dusts. Working alongside clients around the world they have developed a number of dust handling systems for flash furnaces from New Boliden, through Codelco to PASAR. Solving handling issues in dust collection has proved to suit Schenck Process range of equipment well and now a series of solutions are available. Solutions have been developed to handle materials up to 600°C and can convey over 1 km. Conveying to remote location for disposal, injecting directly into a furnace through lances, return to furnace burner feed, or deliver and dose into leaching reactors, Schenck Process are ready to ‘make processes work’. Historic solutions at New Boliden and Codelco demonstrate a range of material application and the long term performance of the equipment. Recent installations at Pasar utilise the Schenck new ProPhaseTM equipment and handle the Waste Heat Boiler and ESP dusts directly and simplify the dust train. The paper will seek to show how this equipment can bring benefit in handling high temperature materials directly and eliminate several traditional steps that are often unreliable. The systems can be paired with Schenck Process new PHASiQTM and STREAMiQTM control systems which are complete PC, HMI, PLC, Interface system with full SCADA, Data Storage and IoT ready remote interrogation and support available. Installed in this challenging environment the systems are ready for smelter use. The systems can be also joined to our new E-nizingTM web portal. A perfect partnership to deliver the trend in ‘Big Data’ while providing visibility and off site support. The paper will show how these systems can deliver reliable equipment and remote support for these often isolated sites as well as delivering rapid return on investment. This paper discusses a step change in simplifying Flash Furnace Dust handling which Schenck believes shows the truth of Schenck Process Solutions claim that ‘we make processes work’.

Jan 1, 2019

By M. Schmidt, P. Nord, M. Larinkari

Cathode stripping machine technology has been developed significantly both in electrorefining (ER) and electrowinning (EW) applications in the last ten years. The main driver has been robotic cathode handling, which has enabled increased flexibility to meet different layout and material handling requirements for both ER and EW processes. Additionally, cathode stripping stations have been continuously developed to optimize speed and to reduce mechanical stress of permanent cathodes. 'taco' type cathodes have been proven as beneficial approach for high capacity operations (particularly in Cu ER), where over 600 cathodes per hour continuous throughput has been achieved. However, the latest developments also apply to split type cathode stripping. Besides material handling, the modern cathode stripping machine has also an important role to provide information for production and quality monitoring. This paper describes the latest developments from the field of copper cathode stripping based on several different projects implemented in the recent years. INTRODUCTION After introduction of the permanent cathode technology in the late 1970s, it became the prevailing technology in copper refineries over the traditional starting sheet process by the end of 1980s. The main driver was less labour-intensive production due to fewer processing steps required along with more automated electrode handling equipment (cathode stripping machine, anode preparation machine, anode scrap washing machine and tankhouse cranes). Since then the design of the cathode stripping machine has followed the development of permanent cathode technology. The main development steps so far can be summarized as follows: Full Deposit Stripping Machine (FDSM) based on waxed permanent cathodes or cathodes with bottom edge strips resulting in split cathodes (copper sheets separated, see Figure 1) Wax less cathode stripping based on V-groove on bottom of the edge strip resulting in either ‘taco’ cathodes (enveloped copper sheets, see Figure 1) or split cathodes Full Deposit Robotic Stripping Machines (FDRSM) using 1–5 robots for permanent cathode handling and cathode stacking.

Jan 1, 2019

By W. Lodge, G. Rasmussen

"The carbon-in-pulp (CIP) process has been the dominant gold recovery technology since the 1980s. During all this time carbon measurement, and control of the carbon transfer pumps has been largely manual in nature. Such manual operation inevitably limits process efficiency, potentially resulting in higher gold solution losses, and higher cost of circuit operation. Based on the authors’ experience, average plant solution loss is in the range of 0.02-0.03 ppm Au, as opposed to the general industry target of 0.01 ppm Au or less. Gekko Systems, in conjunction with Curtin University’s Gold Technology Group, has developed a carbon concentration meter, the ‘Carbon Scout’ meter. The meter automatically measures carbon concentration in all tanks, providing more frequent and more precise data. Combined with SIMCIL, a CIP circuit process model which is used to determine the optimum set points for the circuit, the meter should ensure lower gold solution losses, and more efficient operation of the carbon circuit. This paper will review they critical factors for good carbon management, the development of the meter and results from the first plant installation. Additional benefits of the Carbon Scout, including improved health and safety and the opportunity to measure other key variables in the leach/adsorption circuit from one central location will also be described.INTRODUCTION The carbon-in-pulp (CIP) process was first introduced to the gold industry in the early 1950s at the Carlton Mill in the USA (Fast, 1988), with the modern version of CIP becoming fully developed with large scale installations in South Africa in the late 1970s (Laxen, 1982). CIP quickly became the technology of choice for new operations, and for the retrofitting or upgrading of existing operations. In the 1980s the carbon-in-leach (CIL) circuit configuration became the process design of choice due mainly to its lower capital costs. With 40 years of operational experience, CIP/CIL for gold recovery is now mature a technology, whose operations and limitations are well understood. To extract further efficiencies from such technologies, by improving recoveries and/or reducing operating costs, is challenging and may require new approaches to circuit management. Gekko Systems, in association with the Gold Technology Group at Curtin University, has developed the Carbon Scout, an automated carbon measurement device. This device replaces manual measurement of carbon concentration in carbon adsorption tanks, providing more frequent and more accurate data for control of the CIP process. Data from the Carbon Scout can be used to automatically control the carbon forwarding pumps."

Jan 1, 2018