Search Documents

By John Russell

"Faster, safer, grinding mill relining offers the obvious attractions of reduced mill relining times with the knock-on incentive to reduce all other maintenance down-time, opening the possibility for increased annual plant utilisation.Leading edge liner handler technologies by RME, focused toward even shorter relines for very large SAG and AG mills, have recently split into two quite distinct paths:•,?Single SAG/AG Mill Relining Machines (MRM’s) of very large capacity, such as Newcrest Cadia’s 40’ SAG MRM of 6000 kg capacity and P.T. Freeport’s 38’/34’ SAG MRM of 7250 kg capacity;•,?Twin-machine SAG/AG Mill Relining Systems of moderate to large capacity such as BHP Billiton’s Escondida Laguna Seca 38’ SAG MRM’s, each featuring 4500 kg capacity.RME, its customers noted above and their liner suppliers are providing leadership in this important annual utilisation advance.Once the 24 hour mill shell reline becomes reality, liners designed for maximum profit, not maximum life, albeit exchanged more frequently, become possible too.INTRODUCTIONAt most mineral grinding plants, mill relining activities dictate each maintenance shutdown’s critical path. When annualized, mill relining remains the largest, single influence in defining plant availability.Because of restricted access, both inside and outside the mill, increased application of manual labour has no effect on reducing relining downtime. The only answer for RME has been to develop and apply new relining technologies now known as RME’s Mill Relining System.RME’s primary focus for over twenty years has been the reduction of grinding mill relining times while simultaneously providing a marked improvement in relining safety. Our original (1990) target was to halve traditional (pre-RME) reline times and to eliminate accidents and injury by mechanizing all physical work."

Jan 1, 2008

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By David Whittle

When does a project with questionable viability, warrant further investment? There are cases in which projects, which evaluate to a negative mean probable value, are worth investing in. There are also cases in which projects that evaluate to a positive mean probable value, should not be invested in. The author will present a model for ?project-control?which includes an adaptation of a well know grade-control concept. Comments on Resources and Reserves ?Resource and Reserve estimates are based on positive information (43-101). ?Reserve and Resource confidence qualitatively assessed. ?U.S. Geological Survey (USGS) recognizes Undiscovered Resources (U.S. Geological Survey 2003).

May 1, 2006

Westwood Quebec Long Life, Low Cost CONSTRUCTION UPDATE ? Shaft advanced to 840m (after 1 year), 3 km of down ramp and 2 km of exploration drift ? Head frame and hoist room structure completed ? 2009, 84,700m drilling program completed (increase 9%) 2010 OUTLOOK ? $102 million expenditures planned ? Shaft to advance to 1,300m and the first loading excavate 71,500m drilling program planned

May 1, 2010

By S. Gorzalczynski

The recent trend in underground mine developments is “bigger is better.” This is most certainly evident in the mine shaft and conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed in the past 50 years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident remains conceptually unchanged from Elisha Otis’ design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha’s invention with the last major design change occurring in the late 1940s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment, but also an increased awareness toward safety

Jan 1, 2002

By Maurice Morton

THE use of organic and inorganic stains has found wide application as a means of detection and estimation of organic fibres. Such stains have enabled the analyst to distinguish between organic fibres of different type and even between wood fibres produced by different processes. Among these stains, aqueous iodine solutions have figured prominently, as in the case of the well-known Sutermeister and Herzberg stains. At the Johns-Manville laboratories, the idea of applying a stain to asbestos fibres was first considered solely as a visual aid in the microscopic examination of such fibres. The staining medium used in this work consisted of a 1 per cent solution of iodine in C.P. glycerine, the latter being used extensively here as a dispersing and mounting liquid for asbestos fibre. This iodine solution was found to have distinct staining properties when used on the local chrysotile fibres, and to improve greatly their visibility under the microscope. It was soon revealed, however, that this staining is apparently limited to the chrysotile variety of asbestos, as against other varieties. It can be readily seen that, if such were the case, the staining test would become a very useful tool in differentiating between chrysotile fibre and the other mineral fibres, without recourse to a lengthy chemical analysis. Hence this investigation was launched, with the purpose of obtaining more information as to the selectivity of this stain as well as its mechanism. The only previous work of this nature that could be found in the literature was that of Van Winsen and Graham (1, 2, 3) on the adsorption of erioviolet dye by serpentine and related magnesia minerals. However, these authors did not refer to any specific behaviour of chrysotile as against other types of asbestos fibre.

Jan 1, 1941

By James Mackie

The Vancouver Stock Exchange (VSE) has been providing venture capital for start-up companies since 1907. Ninety years' experience in the junior mining industry has enabled the VSE to develop policies and procedures tailored to the unique needs of start-up companies. Policies and procedures applicable to listed companies are documented in the Corporate Finance Services Department "Policy and Procedures Manual." Approximately 50% of the companies listed on the VSE are in the mineral exploration and development business. The largest number are exploring base metal, precious metal or diamond properties. A recent count shows that about 20 companies are exploring industrial mineral or non-metallic deposits. The minerals sought by these companies include limestone, decorative stone, building stone, lava rock, wollastonite, zeolite, garnet and graphite. There are two basic routes to obtaining VSE financing for an industrial mineral property. The owner can either sell an interest in the property to a listed company or form a company and have it listed on the VSE. In each instance, the listed company is responsible for raising funds to develop the property. A typical financing consists of the sale of company securities byway ofeitherprivate placement or prospectus offering.

Jan 1, 2001

By R. A. Frith

"Belts of Yellowknife Supergroup volcanic and sedimentary strata in the Slave Structural Province are separated by granitoid complexes. The strata and most intrusive rocks are 2.7 and 2.5 Ga old, but rocks around 3.1 Ga have been recognized in some of the complexes and are believed to represent a once-extensive sialic crust. Volcanics were erupted along rifts in this crust and the rifts became sites of crustal foundering and the development of troughs that filled with turbidites of volcanic and granitoid provenance. Present margins of the granitoid complexes may be close to the original margins of deposition of volcanics, with associated mineral deposits, and close to the thickest parts of basins of sedimentation.The Hackett River volcanic belt extends 100 kilometres between Mara River and Back River and is crudely S-shaped, with a northern sector surrounding a core of granitoid basement rocks, a northeasterly facin g central sector and a southerly facing southern sector. Up to 8 kilometres of andesitic volcanics with intercalated felsi c volcanic rocks are preserved within the central sector. The f elsic rocks include thick lenses of volcaniclastics with large, quartz-eye-bearing clasts, but the known metal deposits are not associated with these. Both of the deposit areas, the Hackett River area in the northern domal sector and the 'A itch ' Lake area 40 kilometres to the south in the central sector, are near the tops of relatively thin atypical volcanic sequences above suspected basement rocks. The Yava deposit near 'A itch , Lake overlies a unit of subaerially deposited, welded, andesit ic ash flows and the Hack ett River deposits overlie highly metamorphosed volcaniclastic rocks that include suspected ignimbrites.The deposits are notably argentijerous and lead-rich. They consist of stratigraphically zoned sheet-like bodies of iron sulphides, sphalerite, galena and chalcopyrite underlain by altered rocks containing chalcopyrite stringers. The Yava deposit was formed where hydrothermal fluids exuded through the fractured floor of a flooded caldera basin. The Hackett River deposits may have been formed in a similar setting and it is not inconceivable that all the known deposits in the belt were formed in a single large caldera basin, although there is no independent evidence for the required major fault separation between the Hackett River dome and the 'Aitch' Lake area."

Jan 1, 1980

By M. Narita, S. Nakayama, M. Fujihara

Hibi Kyodo Smelting Co., Ltd. was founded in 1968 and celebrated its 50th anniversary in 2018. In 1972, we started producing copper cathode with a production capacity of 84 KTPY. Since the company founding, we have undertaken seven expansion projects, and our current copper-cathode production capacity is 290 KTPY. To increase our production efficiency, two tank houses were converted from Conventional process to ISA process in 2006 and 2014. In another investment, we equipped a continuous glue dosing system, which allowed for strict additive-concentration control, yielded quality improvements and reduced the power-consumption rate. Along with an increase in the production of copper cathode, the amount of impurities eluted from the anode increases. To solve this problem, the chelate-resin purification process that was introduced in 1983 was renovated, and impurities could be recovered more efficiently. In this paper, we report various improvements that have been implemented at the refinery since 2000. INTRODUCTION Tamano Smelter and Refinery of Hibi Kyodo Smelting Co., Ltd., founded in 1968, celebrated the 50th anniversary of its founding in 2018. The Tamano Smelter opened its No. 1 tankhouse in 1972, and began operating No. 2 tankhouse in 1984. Thereafter, with continuous production increases and technical improvements, electrolytic copper production was increased from 84 KTPY to 290 KTPY as shown in Figure 1. Table 1 shows the major operating facilities and operation data in 2017.In this paper, details of equipment introduced to continuously dissolve and add glue, various improvements made to the chelate resin process, enhancements made to the crude Ni sulfate process, and another vibrating screen introduced to the copper slime processing flow in accordance with the expansion of copper production capacity since 2000 are reported.

Jan 1, 2019

By A. M. Bell

"The property of Gaspe Copper Mines, Limited, is in the Gaspe Peninsula some 60 miles west of the town of Gaspe and 20 miles in from the north coast. The Copper Mountain deposit was first discovered in 1921 and first optioned and drilled by Noranda in 1938. The Upper Needle Mountain showings a mile south were found in 1938, but it was not until after a delay of 10 years that the more important deep ore at Needle Mountain was located by drilling. Production started in 1955, and the smelter commenced operation in December. Mining is by open stope methods with first production coming from the Lower Needle Mountain orebody, of which only a small portion has been exposed in underground openings.Stratigraphy and AlterationThe country rock is composed of limy siltstones of Devonian age. Away from alteration these are dark and generally carbonaceous. Throughout the drilled area numerous narrow layers of tuffaceous fragmental material occur, and such beds are found to provide excellent horizon markers by virtue of their uniform thickness and wide lateral distribution. These markers are valuable for stope control in mining the bedded replacement deposits.Intruding the sediments at Copper Mountain are porphyry dykes, and one drill hole encountered granite 1,400 feet below the valley. Solutions responsible for the rock alteration and ore deposits seem to have emanated from this intrusive centre.On the mine claims strong hydrothermal alteration has completely obscured the original character of the sediments. The unaltered formations are all very similar in appearance, but following alteration rocks that are very dissimilar in physical characteristics are produced, and such differences have an important influence on ore deposition. The alteration effects are known to extend over a vertical range in excess of 3,000 feet and have a surface area of two square miles. All known ore bodies are within the zone of alteration. In this, rocks are strikingly bleached to a white colour in contrast to the normal dark-coloured sediments, and are much harder and more abrasive, with bedding often obscured. The first effect of alteration is driving off of carbonaceous matter, followed progressively by silicification in the acid rocks and by the formation of lime silicates in the lime rocks, with an accompanying gain in silica and a corresponding loss in lime. Extensive analysis has shown that there is an actual addition of silica involved in the alteration."

Jan 1, 1949

By C. J. Hodgson

"IntroductionThe Kitsault molybdenum mine is located 600 m above sea level on Lime Creek at the head of the inlet of Alice Arm, 140 km northeast of Prince Rupert, British Columbia (Fig. 1). The area of the mine is characterized by rugged topography and deeply incised creeks which drain into the Portland Canal - Observatory Inlet fjord system. Access is by air service or boat from Prince Rupert, or by secondary road from Terrace.HistoryThe deposit was first staked in 1911, at which time the main feature of interest was a polymetallic vein with values in silver located southeast of the molybdenum deposit (Woodcock and Carter, 1976). Turnbull (1916) was the first to describe the extensive zone of crisscross quartz stringers with Mo~ on the banks of Lime Creek which, although it clearly had the potential to contain a major deposit, was not then believed to be of commercial value.Following sporadic work through the 1920s and early 1930s, the ground lay idle unti11959 when Kennco Explorations (Western) Ltd. commenced a program of systematic diamond drilling on the stockwork-type mineralization adjacent to Lime Creek. In late 1964, Kennco announced the presence of an orebody of 36 million tonnes averaging 0.230Jo Mo~ which was to be put into production at a rate of 5450 tonnes per day under a new subsidiary, British Columbia Molybdenum Ltd., at a forecasted capital cost of $20 million (revised to $30 million).Between January 1968 and April 1972, 10.4 million kg of molybdenum were produced from 9.3 million tonnes of ore, at an average mill recovery of 90%, and with an average mill head grade of 0.206% Mo~. The ore was mined in an open pit with a waste to ore stip ratio of 1.5 to 1. The. operation was terminated in 1972 due to weak molybdenum prices and escalating costs.In May 1973, the deposit was purchased by Climax Molybdenum Corporation of British Columbia, Limited and in 1979 transferred to affiliate Amax of Canada Limited. In early 1979, following completion of detailed feasibility studies, Arnax commenced construction of the 10 900 tonne per day Kitsault mine and mill complex based on a mineable open pit reserve of 95 million tonnes at an average grade of 0.192% Mo~, sufficient for a mine life of 25 years. The original capital cost estimate was $143 million; it subsequently escalated to approximately $200 million."

Jan 1, 1995

?Why TSM in Canada ?How it was developed ?Architecture and Goverance ?COI panel ?Performance indicators and how they work ?External Verification ?Reporting ?The national organization of the Canadian mining industry ?Mining, smelting and refining of base and precious metals ?Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ?Many associate members ?www.mining.ca

May 1, 2011

By T. G. Joseph, G. W. Hansen

"This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sands material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 sq. yd. Consequences are manifested in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability.The objective of these considerations, as part of the Oil sands-Equipment Interaction Program (OsEIP), currently a joint venture between Syncrude Canada Ltd., James Progithin International (JPi) Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta, is to identify and provide feedback to the manufacturer and end user of adverse shovel-ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance."

Jan 1, 2002

By D. Yamada, T. Tanaka, N. Inouchi, J. Nakahigashi, H. Yoshimura, T. Nonishi

The use of cereal food materials as lubricants was investigated in an attempt to develop nonpolluting lubricants. Suspensions of wheat flour in water and other types of cereal food lubricants were prepared and their friction coefficients measured. The results indicate that a cereal food lubricant containing 30% lipids, 2% proteins, 60% carbohydrates and 0.6% calcium carbonates has the lowest friction coefficient for a sheet (cpTi-1). As example applications, the lubricant was tested with a forming press and a screw-fastening device. In both applications the cereal food lubricant performed relatively well in comparison to conventional lubricants and thereby has potential for practical applications.

Jan 1, 2006

By Daniel D. M. Adams

Over the last 100 years industry in general has been trying to advance the ability to maintain systems through management processes. Mining has looked to utilize onboard data systems in our mobile mining fleets to compliment these processes. Combining the two concepts build the concept that Rio Tinto refers to as asset health. These programs can generate a cost shift between $20,000 and $100,000 per piece of equipment annually. Even with the documented savings many operations struggle to justify the systems, why?

May 1, 2011

By Cz. Mora, A. Pawelczyk, D. Hreniak, P. Nowak, A. Dyonizy, S. Strek, W. Strek, K. Grabas, A. Ostrowski

Globalization and a growing demand for limited raw material resources have forced changes in the approach to the supply chain. This is particularly true in the case of rare earths, which are regarded as one of the most important development indicators of modern technologies. To ensure a secure supply of commodities, the European economies have been prompted to investigate REE recovery from sources which until recently, for technical or economic reasons, were considered not sufficiently attractive. An interesting example is apatite phosphogypsum waste dumps. The REE content in these waste dumps averages around 0.5-1 %. One of the most important phosphogypsum locations in Poland is the Lower Silesia region where a phosphoric acid Chemical Plant "Wizów" operated for several dozen years. In this work, rare earths are leached from the phosphogypsum crystalline structure by a chemical treatment and can then be separated into individual chemical compounds. The technology used in these recovery tests, matches up to a coherent European raw materials policy supporting effective management of resources and promoting waste materials recycling.

Jan 1, 2014

By M. Grenon

OBJECTIVE ?To link slope stability and financial assessment algorithms into a commercially available mine design software packages to provide integrated global pit optimization.

May 1, 2013

By Aparup Chattopadhyay, Barun K. Gorain

"Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.INTRODUCTIONA novel characterization tool has been developed for double refractory gold ores and complex copper-gold ores using state-of-the-art technology for quantitative gold and copper deportment study. The characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulphide phases and variable proportion of visible and invisible gold in different sulphides phases (pyrite, chalcopyrite, chalcocite and bornite) and iron oxide phases (magnetite, hematite and goethite). A study was initiated on various ore deposits and also on samples representing various processing streams of pilot plant batches such as flotation concentrates and tailings. This paper attempts to discuss the deportment characterization methodology through presenting results from investigations on four samples from a flotation circuit viz, Feed, Final concentrate, Cleaner Scavenger Tail and Rougher Tail samples. These four samples represent the key streams for a typical copper-gold flotation flow sheet. The key objective of this investigation was to identify and quantify visible and invisible gold along with understanding the morphology and liberation of gold associated with various sulphides, Fe- Oxides and non-sulphide gangue species. In addition, the aim of this study was also to relate this mineralogical and gold deportment information to metallurgical performance."

Jan 1, 2013

By V. Gaudreault

Rio Tinto Alcan (RTA) has three smelters that use the Alcoa P155 technology: two in Canada (Grande-Baie and Laterrière, Saguenay, QC) and one in the United States (Sebree, Kentucky). The oldest RTA P155 smelter was built in the 1970s (Sebree) and had an initial current intensity of 155 kA. In the 1990s, RTA installed an amperage booster in Grande-Baie smelter to increase cell productivity. Since then, RTA has continuously pushed the limit of this technology and the target amperage that was 195 kA in 2005 has been increased to 210 kA in 2010.This article describes the successful plant-scale trials to increase current intensity from 195 kA to 210 kA, and the key performance indicator results. It demonstrates RTA's technology leadership to undertake such a development with its Brownfield smelters.

Jan 1, 2011