Search Documents

By C. Sideco

"Concentrate drying at the Sullivan Concentrator goes back to 1937 when the original coal-fired dryer was put into operation. This was a second hand 8' dia. x 56' long Struthers-Wells rotary dryer that came from the phosphate plant in Warfield, B.C.In 1962, replacement of the old dryer was seriously considered. The shell and the auxiliary drive mechanism were badly worn and needed replacing. In April 1963, the new 8' dia. x 65' long fuel oil-fired Struthers-Wells dryer went in operation at an installed cost of $174,000.In 1965, it was apparent that a major rebuilding of the dust collecting system would have to be done. A study was carried out and a Ducon Dynamic Gas Scrubber was installed. The system went in operation in November 1966 and has fully met expectations.In the same year, the zinc dryer was converted from fuel oil to natural gas. The conversion has resulted in savings in fuel cost of 12 to 15%.Frame No. 1Zinc Dryer PerformanceDryer Make - Struthers-WellsDryer Size 3/4 8' dia. x 65' long Drum Drive - 100 HPSpeed of Rotation - 5 RPMFeed Rate - 50-65 TPHFeed Moisture - 10-12%Discharge Moisture - 4-6%Dryer Inlet Temperature - 1600-1800°F Dryer Outlet Temperature - 200-250°F Stack Gas Volume - 25,000-40,000 CFNDust Collecting Efficiency - 99.75-99.98% Duet Loss in Stack - 50-300 lbs./day"

Jan 1, 1972

By Guy Chevalier

QCM?s pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented. This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.

May 1, 2003

By Chin J. Chang

Powder metallurgy (P/M) technique is known for its capability of producing near-net-shape parts. Its specific characteristics have resulted in low cost and eliminated of many secondary machining. However, more and more P/M parts do require additional operations to fulfil their complex geometric features and surface roughness. Many of the machining factors that influence the machinability of cast and wrought steel parts, such as cutting speed, feedrate, coolant, tool geometry and shape, are also considered in the machining of P/M components. The special feature in P/M structure is the porosity that can decrease the machinability and shorten the tool life. Different variables have been considered in the machinability of P/M materials. Densities and the free machining additive manganese sulphide (MnS), are the two main factors of material composition, which dominate the P/M machining performance. Machining process is the main method that generates the desired working surface of machining components. This paper will discuss the metallurgical structure of the powder metallurgy components, their physical properties and possible issues when encountering machining operation. Turning operation has been tested in this investigation to show the relationship between the cutting speed, federate, cutting forces and chip formation. This investigation also discusses how the free machining additive, manganese sulphide, affects the P/M structure and machinability in order to understand how the metallurgical structure can affect the machining operation and, how to obtain the optimised surface results.

May 1, 2001

"This document sets out the Exchange’s expectations and requirements for a valuation of mineral properties and outlines: the general purpose of valuation reports; guidelines respecting circumstances where the Exchange will require a valuation report; and valuation standards, guidelines and methods that are generally acceptable to the Exchange, 1. IntroductionThis Appendix sets out the Exchange's expectations and requirements for a valuation of mineral properties and outlines:(a) the general purpose of valuation reports;(b) guidelines respecting circumstances where the Exchange will require a valuation report; and(c) valuation standards, guidelines and methods that are generally acceptable to the Exchange.Mining industry standards and guidelines for valuations and valuation reports can be found in the Canadian Institute of Mining, Metallurgy and Petroleum Standards and Guidelines for Valuation of Mineral Properties (""CIMVal"") published in February, 2003 (www.cim.org). CIMVal consists of two parts, Standards and Guidelines. The Standards are mandatory and must be followed in order for a valuation to be CIMVal compliant. The Guidelines in CIMVal are not mandatory, but are strongly recommended.The Exchange requires that CIMVal Standards be used by Issuers and their professional advisors when preparing valuations and valuation reports on mineral properties. The CIMVal Guidelines should be followed by Issuers and their professional advisors in preparing valuation reports on mineral properties, with the exception that the valuation methods and guidelines under Section 4 Acceptable Valuation Methods and Guidelines below, must be followed."

Jan 1, 2003

By C. O. Aksoy

Operating the underground marble quarries effectively, it is important to evaluate the deposit blocks economically which are affected by the suitability of the topography and configuration of bedding. The joint sets within the deposit and the spacing between these discontinuties are also of great importance. In this study, the marble deposits that could be geomechanically eligible for underground excavation have been selected throughout Turkey and these selected reserves have been classified accordingly by Q-Rating System. These classified marble deposits that forms groups of 1,2, and 3 (groups were determined by evaluating the O-rating, topography, quarry situation, cracks, joints etc.) are convenient for this type of production. Nevertheless, when the auxiliary factors (topography, location, production method etc.) regarding the deposit have also been investigated, the most convenient sub-group of deposits (Afyon Tiger Skin, Burdur Beige, Diyarbakir Pink and Mugla White) have emerged. The sizing of the pillars have been performed utilising Bieniawski?s stress profile. The LAMODEL software, developed by National Institute for Occupational Safety and Health (NIOSH), USA and run under the laminated displacement discontinuity method, has been used to size the pillars. This work brings in a novel opportunity to Turkey, in which no underground marble quarry has been attempted up-to-date similar to its several examples in Italy, USA, etc. This study serves as a reference for the marble operators and for the pioneering application of laminated displacement discontinuity method in hard rocks.

Apr 1, 2005

By G. Molloy

The purpose of this paper is to demonstrate the value of applying continuous improvement, in particular 5S and standard work, in an underground environment. 5S and standard work are two aspects of Lean manufacturing that have been applied in many industries. At Vale Canada Limited, the focus is to first stabilize the process, commonly through the use of 5S, standard work and other continuous improvement techniques. In parallel with building an engaged workforce, these approaches aim to incrementally stabilize and improve a process. 5S is an employee-driven, systematic methodology to reduce waste in all its forms through attaining, maintaining, and improving workplace organization. Identified as a foundational part of any improvement process, 5S aims to remove wastes that impact on the overall efficiency of the area. Standard work is used to formulate a common approach to how tasks are carried out to ensure consistency. Standardization involves identifying, establishing, and following the best method. The aim is to eliminate the variation that can occur when there is not a pre-defined established standard. Demonstrating the value of 5S and standard work in an underground environment will be achieved by first understanding the overall concept of Operational Excellence and continuous improvement as practiced within our operations. The paper will then cover a real application of 5S and standard work within the underground environment at Thompson, Manitoba.

Aug 1, 2013

By Collin Bartlett, H. Storch

"Modern metallurgical processes operating with oxygen enriched air, such as the Outotec Flash Smelter and Flash Converter, generate very concentrated SO2 off-gas, which in combination with Outotec sulphuric acid plant technology allows the production of high pressure steam to be used for power generation. Outotec combines well proven technology of sulphur burning plants for this purpose with metallurgical plants.The application of Outotec’s proven LURECTM process enables processing of SO2 gas of up to 25 vol.-%. This process maximizes the energy recovery from the SO2 oxidation at a suitable high temperature level which can be turned into high pressure steam. The application of the Outotec HEROSTM heat recovery system enables the generation of low pressure steam from the absorption energy released at the intermediate absorption step. Additionally, energy is also recovered in the acid coolers for boiler feedwater pre-heating.The concept of integration of high and low pressure steam in combination with the pressurized operation of the boiler feedwater deaerator, thus heating up the boiler feed water to temperatures around 160…170°C, enables indirect transfer of low pressure steam (for deaerator operation) into more valuable high pressure steam, which improves the degree of heat recovery. This is the characteristic of Outotec’s HEROS+TM process.The increased generation of high pressure steam will in turn enable the generation of more electricity when compared to a standard traditional sulphuric acid process."

Jan 1, 2014

By Brien A. Perry, Art Wiebert

"Many organizations which have implemented Total Quality Management (TQM) are finding that the process has either stalled or is not working so well as originally envisioned. This can be particularly evident in an engineering environment where the uniqueness of engineers and their particular culture has not been adequately considered. Winning the commitment of a highly educated group ojprojemnnJJ1s to the TQM concepts, which are often initially 5W2 as too simplistic poses special challenges.Successful TQM implementations are found among technical groups where employees have significant input into creating the new work culture, feel empowered to make changes and are well trained in teamwork. A coach who is knowledgeable in implementation problems can, when working closely with the technical teams, help them circumvent obstacles and guide them successfully through the difficult early phases. The remaining key ingredient for success is supportive management which leads the change and is both informed and appreciative of the accomplishment being made.This Paper is based on first-hand experience with common problems and results encountered in implementing TQM in an engineering environment. Described in the paper are ways of avoiding these problems through awareness of the unique nature of engineering groups, implementation planning, just-in-time training and coaching people in the TQM process. The paper concludes with a focus on the opportunities and results from a successful implementation. These opportunities and results include the benefits each engineer can realize through process thinking, empowerment and teamwork."

Jan 1, 1995

By Louis R. Bernier

Most systematic studies carried out on passive treatment systems incorporating the use of limestone drains, under aerobic or anaerobic conditions, essentially deal with the treatment of effluents from mines in the USA. A limestone drain typically comprises a trench filled with crushed limestone rocks surrounded by impervious materials. In the case of anoxic drains, the trench is generally isolated under a geomembrane liner covered with soil. Contaminated mine effluents flow by gravity towards these limestone drains where the passive treatment consists in bringing the carbonates into solution, thus increasing the pH and alkalinity. Factors to be considered in the design are: chemistry of the contaminated mining effluent ([metals, [Al], [sulfates], dissolved oxygen, acidity, pH), desired residence time, nature of the rock, grain size, density, void ratio and mass of the limestone rock used, alkalinity, life span and hydraulic behaviour of the drain. Certain secondary effects (saturation by sulfates, co-precipitation, adsorption) may either be beneficial (lowering the sulphate and metal load) or harmful (armoring the limestone rock and clogging of the drain). This paper gives a brief status report on the available knowledge on the use of limestone drains for passive treatment of mining effluents heavily loaded with metals. Examples given include the old Lorraine mine (Ni-Cu), Témiscamingue, where limestone and dolomite rock drains were installed in 1998 when a cover with capillary barrier effects was placed over the tailings site.

Nov 1, 2002

By Robert B. Parsons

"It is quite likely that more than a handful of junior exploration companies will receive some startling news from their accountants this spring when 1989s tax returns are being prepared. These companies could find that, for the first time ever, they will have to write a cheque to the federal government on account of a new federal capital tax which became effective July I, 1989IntroductionMany mining companies which have never had to pay a federal income tax are finding that they indeed have a tax liability for 1989. Non-producing companies, such as junior exploration companies, almost automatically assume that they don't have to pay any income tax. But, a new tax imposed under the Income Tax Act catches especially the company that has no income.Effective July 1, 1989, a federal capital tax (some call it a corporation minimum tax) is payable by any corporate carrying on business in Canada where the corporation has ""taxable capital"" exceeding $10 million. As a result of the popular use of flow-through shares in recent years, many junior exploration companies are finding that their balance sheets show capital stock over $10 million, and that they are consequently caught by the new tax. Further, some of these companies are finding, to their chagrin, that the tax for 1989 was due on February 28, 1990, and that non-deductible interest is ticking away on unpaid taxes."

Jan 1, 1990

By Yves Prévost, Guy St-Amant, Guillaume Dion

In 2010, the foreseen increase of copper grade in feed concentrate at the Horne Smelter was a significant challenge to maintain a steady copper flow throughout the process. The Horne Smelter process includes a Noranda Reactor, a Noranda Converter, pyro refining vessels and anode furnaces. Of the many challenges involved, improving the single casting wheel performance was one of the key topics. Its reliability had to be improved to meet the new production objectives, as anode copper production was to increase from 170 000 to 225 000 tonnes/year. A multidisciplinary team was dedicated to improve the casting wheel availability. The improvement project allowed pinpointing failure modes and reviewing operational and maintenance practices. The common understanding developed by the team allowed improving small components with a high gain-to-effort ratio. The project allowed reaching operational targets without any significant investment. INTRODUCTION In operation since 1927, the Horne Smelter, located in Rouyn-Noranda, in Quebec, has undergone several technological changes since its original construction. Built to smelt the Horne mine concentrates, the smelter also accepted some local custom feeds from the first years of operation. When the Horne mines stopped production in 1976, the plant became a 100% custom smelter. With the development of the Noranda Reactor (1973) and Noranda Converter (1997), the Horne smelter increased its productivity and improved its environmental performance. Continuous improvement of the Horne process allowed maintaining a high level of flexibility in the operation of the smelter, while improving its overall capacity.

Jan 1, 2019

By Janne Karonen, Stephen Hughes, Mikael Jåfs, Jan Stål, Hannu Johto

End-of-life electrical and electronic scrap material attracts attention as a good opportunity for new value creation through efficient metal and energy recovery of such materials. On the other hand, the treatment of such wastes becomes important to avoid problems for society and environment. Treatment of such secondary raw materials faces multiple challenges due to their increasing complexity and evolving nature. Processing of these complex scrap materials together with recovery of a wide range of valuable metals with a combination of pyrometallurgy and hydrometallurgy using Outotec technology is discussed in this paper. One key consideration is environmental performance which needs attention when processing such complex secondary E-waste materials. Outotec has successful experience with commercial projects in the countries at the forefront of environmental and operational standards. INTRODUCTION Increasing attention has been drawn to the responsible processing of end of life Waste Electrical and Electronic Equipment (WEEE) as part of metals recycling, especially copper. It has been estimated that the amount of WEEE globally in 2016 was around the level of 46 Mtpa (Balde et al., 2017), representing a major disposal challenge but at the same time huge opportunity for resource recovery. The potential for increasing the recovery is high, because the official recycling rate of WEEE is in 2016 only 20% (Balde et al., 2017) and at the same time the estimated increase of the WEEE amount is between 3 and 5% per annum in the EU (Eurostat, 2019).

Jan 1, 2019

"Cambior currently has nearly 80 exploration properties, acting as operator on about 60 of these. The company's exploration budget has increased to over $11,100,000 for 1990. On-going efforts recently yielded a new gold discovery on the Douay- Vezza property, a joint venture project with Inco and Vior. Cambior continues to seek out new opportunities, recently acquiring an option agreement on the Sleeping Giant project in Quebec and four new exploration agreements in the United States, through its Reno office. Other nearly-concluded joint venture agreements have also given the company entries into Indonesia and Guyana.SummaryWhen it acquired SOQUEM's assets on August I, 1986, Cambior also acquired interests in 45 exploration projects. The subsequent mergers with Aiguebelle Resources and Sullivan Mines in 1987 brought the total number of exploration projects to 83, most of which are concentrated in northwestern Quebec. Cambior's strategy emphasizes gold exploration, and exploration activities were, therefore, initially limited to the Val d'Or and Rouyn-Noranda mining camps, where Cambior has a large portfolio of properties. Approximately $25.8 million has been spent on surface exploration in this area since the formation of the company, resulting in the discovery of the Mouska deposit and four sub-economic zones on the Porcupine, Forbex, Bloc Sud and Flavrian project s. In 1988, Cambior became involved in projects in the United States to which the company expects to allocate about 38070 of its 1989 exploration budget."

Jan 1, 1990

By L. R. Bower

"This paper describes a highly versatile variable speed unit with a torque multiplication feature as a direct replacement for a fluid coupling .The unit is comprised of a modulating clutch with torque converter and lock-up options.The UCD does not start or stop the motor. This is carried out in the normal manner.The UCD continually monitors and rapidly regulates the output speed to the requirement of a set point demand from input signals or a pre-set program with full manual override.The pre-set program can include start and stop ramps, top speed and minimum speed regulation and also mid-speed set point with security for man-riding, etc. Speed variation is from zero to 100% on a constant duty basis.The input signals can be from any source, e.g. belt weigher. load profile bunker probes, mine monitoring system, etc.The UCD when fitted with a torque converter has a torque multiplication feature which automatically provides a starting torque up to two and a half times greater than the full load torque without exceeding the normal motor power levels.IntroductionIt is common practice in the mining industry to drive conveyors, whether they be belt or chain, through a transmission system incorporating a fluid coupling between the driving motor and gear-box .However, there are drawbacks and in an effort to attain a better degree of drive and control, two-speed motors - inverters cycle- converters - hydrostatic drives, etc ., have been introduced."

Jan 1, 1986

By D. M. Cruden

"When two discontinuities form a tetrahedral wedge in a rock slope, a factor of safety for the wedge can be simply calculated (if motion is driven only by gravity and resisted only by friction) from plots of the normals to discontinuities on an overlay of a polar, equal-area spherical projection to which the great circles of a similar equatorial projection have been added.IntroductionThe stability of slopes in rock masses is often controlled by the discontinuities that exist in the masses. In particular, the geometry of the discontinuities constrains the ways in which the mass may fail. Displaying the orientation of the discontinuities on a spherical projection has been found to be a useful way of identifying possible failure modes. The most concise display shows the orientation of the normals (or poles) to the discontinuities that compose the fabric of the rock mass. Computer processing of large samples of discontinuity orientations is necessary if the sampling biases identified by Terzaghi (1965) are to be routinely corrected. Fortunately, displays of the poles to discontinuities (or pi diagrams) are relatively easily produced on the line printer of a computer or by a computer plotter (Cruden , 1978; Ramsden and Cruden, 1979). Unfortunately, further analysis of the stability of a rock mass has tended to use traces of typical discontinuities on a spherical projection rather than pi diagrams; examples may be seen in Hoek and Bray's book (1981)."

Jan 1, 1990

By K. Fumimura, T. Nishimura, M. Kohno

When applying numerical techniques to problems of deformation of rocks, the body to be analyzed is divided into small portions and is represented by a system of points linked together with the neighboring points. In the so-called distinct element modeling, the particles in the system are directly connected by springs and a contact law is used to specify forces on the particles to simulate the mechanical behavior of the body. The relation between the spring stiffness and commonly measured material properties, such as the Young’s modulus and the Poisson’s ratio, should be known a priori. For the general case of a random packing of particles, the relation is found by means of a process in which a system of particles and set of parameters are prepared to simulate a set of specimen-size test and then the input parameters are chosen to match the measured material properties. The validity of the numerical result is only demonstrated by comparison model behaviors with the measured responses. The process includes trial-and-error manner, therefore, no model is complete to reproduce the mechanical properties. In this paper, a relation between the spring stiffness and the elastic constants; the Young’s modulus and the Poisson’s ratio, is introduced to a three-dimensional distinct lattice spring method. Two simple numerical examples will be presented to demonstrate the performance of the method with the procedure for the determination of the spring stiffness.

Jan 1, 2015

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By Robert B. Parsons

"Next month will mark the anniversary of the release of an important federal study on a mineral policy for Canada. The study, entitled ""Mineral Policy-A Discussion Paper"", provides well-researched coverage of a broad range of issues that are of interest to the mining industry. Unfortunately, there is a real possibility that the discussion paper will wither and die on the vine, unless the federal and provincial governments, and the private sector, collectively ensure that some of the key considerations which are raised by the paper are acted upon.IntroductionAlmost one year ago, on March 8, 1982, Federal Mines Minister July Erola released an important study entitled ""Mineral Policy-A Discussion Paper"". The discussion paper, which presents the government's assessment of the opportunities and constraints facing the Canadian mineral industry in the 1980s, was prepared within the context o f three principal objectives-strengthening the resource base on which the industry rests, ensuring the adequacy of research activities needed to support development of the resource, and furthering the development of markets for the resource It is clear that, in today's economic climate, not even the most generous incentives would turn the industry around: what is needed is a sound base for future development, when this is possible. In this regard, the discussion paper is an excellent stepping stone, in that it reviews a wide range o f fundamental policy issues which touch on all facets o f the mining industry."

Jan 1, 1983

By A. G. Storey, J. B. W. Bailey

"The Noranda Process at the Horne Division ofNoranda Mines Limited now smelts approximately 350,000 short dry tons of concentrate a year, which is 40% of the total smelter throughput. Campaigns are averaging 200 days and refractory consumption is much lower than in the conventional smelter.In this paper, details ofrecent operation are given, together with updated projections for operation with higher levels of oxygen enrichment.IntroductionThe Noranda continuous smelting process has been in operation at Noranda, Quebec, for six years and in that time it has smelted a million and a half tons of concentrate. It is currently smelting 1,200 to 1,250 tons per day of concentrate on an instantaneous basis"" and it is handling approximately 40% of the Horne smelter throughput.This paper will describe the current operation of the process and the improvements that have been made since 1976, when the process was described by L.A. Mills et al.lSince early in 1975, a high-grade matte averaging 73% copper has been produced, which is then sent to the converter aisle for final treatment. All the information in this paper refers to the operation of the process in the matte mode .Early in 1978, Kennecott Copper Corporation started up their new smelter near Salt Lake City, Utah , which has three Noranda Process reactors operating with high oxygen enrichment of the tuyere air (2). These furnace s incorporate some design improvements, which will be described briefly."

Jan 1, 1980

By W. H. Hodgson, A. R. Preston

"Improved rail production techniques provide new options for the rail user. Steelmaking improvements offer tighter composition control, lower oxide and sulphide counts, greater control of segregates and freedom from hydrogen problem s. New ultrasonic, laser and eddy current equipment gives printout information on surf ace flatness, straightness and internal condition. These have come along at a time when dramatic changes have occurred on the rail heat treatment scene. Rails can now be deep hardened on or offline in ways which should eventually result in a complete rewrite of the world's specifications. Rails of simple composition can be produced in the hardness range 2801400 BHN as required. The rail user can choose the hardness within this range according to requirement without the necessity for any step changes in the process routes.It is suggested that this is the pattern f or the next decade.IntroductionRails have been the subject of very slow improvement over many years but developments gathered momentum in the early seventies. Recent improvements in quality and properties have provided dramatic increases in rail life under the more severe service situations. Rail profile grinding, lubrication and other track improvements have greatly added to expectations of even longer life. All of this, coupled to even newer mill heat treatment developments, tilt both technical and economic advantages away from tradition to the point where specifications will need to be rewritten so that railroads can take full advantage of these new products."

Jan 1, 1988