Search Documents

By Marvin J. Udy

THE preparation of this paper is in response to many requests for in-formation on the mining and smelting developments which have been carried on for the past three years or more by the Chromium Mining and Smelting Corporation of Canada. By way of introduction, the following paragraphs, relating to the early history and present status of the chrome-mining industry in the United States, are of interest. They are quoted from Bulletin No. 76 of the California State Mining Bureau, published in August, 1918: 'Chromium was discovered about 1797 by a French chemist, Louis Nicolaus Vauquelin, in ore from Siberia. From that time until 1827, the Urals, in the region of Ekaterinburg, supplied the chromium used in . Europe. In the summer of 1827, as the historian advises us, Isaac Tyson, Jr., saw in a Baltimore market-place a cart containing a cider barrel, which was held from rolling about by some heavy black stones. He had made a study of such stones at the first-known American locality, the Bare hills near his father's home, six miles from Baltimore, and he recognized the black stones as chromite. On inquiry, he found the chromite came from the Reed farm in Harford county, 27 miles northeast of Baltimore. At this time, Tyson was one of the very few men in the country who knew the value of chromite, and in the next few years he took full advantage of this knowledge. He immediately bought the Reed farm. He found about 30 tons of float-ore on the surface, but there was no outcrop of ore in place. Never-theless, he sank a shaft, and at a depth of eight feet struck an ore-pocket which proved to be 80 ft. long, 25 ft. wide, and 8 ft. in maximum thickness. His next discovery was of placer chromite in the sands in the beds of brooks on an estate called Soldiers' Delight, 16 miles northwest of Baltimore. Thus far, Tyson's observations had shown him that chromite occurred apparently only in serpentine areas. His explorations were now leading him farther afield. In 1828, he found on the Wood Farm, in Lancaster county, Pennsylvania, a deposit of float chromite which led him to lease the ore-right of the farm, which he finally purChased in 1832. Here he developed the famous Wood mine, the largest single producer of chromite in the world.

Jan 1, 1938

By A. Azizi, P. Blatter, A. Bouajila

ABSTRACT In-situ monitoring of gold dissolution by means of a rotating electrochemical quartzcrystal microbalance unveiled dramatic decreases in gold leaching from sulphide-rich ore after 360 minutes in an actual cyanidation circuit. Pre-oxidation was effective in enhancing gold extraction by preventing a passive film from forming on gold surfaces. This work aims to highlight efforts undertaken to determine (1) how gold cyanidation is limited by passivation, (2) what reactions and mechanisms are involved during sulphide-rich ore cyanidation, and (3) how peroxidation efficiency of an industrial sulphide ore is controlled by galvanic associations between its sulphide constituents.

Jan 1, 2013

By R. Bainbridge

"IntroductionTHE LEAD SMELTING Department of The Consolidated Mining •and Smelting Company of Canada, Limited (Cominco), at Trail, B.C. treats materials from numerous sources for the recovery of lead, •and, of secondary importance, for the .recovery of sulphur as S02• The Department's sintering section has a .capacity of 1,500 tons daily. This section is being replaced by •a new charge-•handling and sintering plant with a daily capacity of 2,000 tons of finished sinter. Materials handled in the sintering section comprise concentrates, ores, and fluxes from Company mines and from 'custom' (independent) producers, together with intermediate products from various plants of Cominco'•s Metallurgical Division, all of which must be treated to, make up a chemically balanced charge of a predetermined lead content for the sintering plant.As received, 80 •per .cent of these materials are finer than 200 mesh, and one-quarter of the tonnage (dry basis) is a slurry .at 30 to 40 per cent moisture. This slurry, a -residue from the electrolytic zinc operation, was, for many years, partially dried before being mixed with other dry materials to make up the sinterplant charge.Some experimental work carried out in 1937 indicated that the metallurgy of the sintering operation could be improved by adopting a technique of 'wet-mixing' followed by controlled drying and nodulizing."

Jan 1, 1953

The dissolution of chalcopyrite has received a significant amount of attention. The predominant paradigm of investigation is that its rate of dissolution is limited or passivated by a surface coating or film of material. The common candidates for such a passivating coating are numerous: polysulfide coating, metal deficient layers, copper sulfide coating, bornite layers, jarosite precipitates, and elemental sulfur films. While this line of explanation, that is, the explanation based on passivation, seems to have won some form of consensus with researchers, there is another explanation for the results that can account for all the results observed. Crundwell (1988) proposed that the solid state properties of chalcopyrite, in particular, the semiconducting properties, are responsible for the observed behaviour of chalcopyrite. The purpose of this paper is to outline the semiconductor mechanism of dissolution, and to show how this mechanism accounts for all the observed phenomena recently reported in the literature. The paper outlines the semiconductor mechanism of dissolution, shows how this mechanism accounts for the dissolution

Jan 1, 2014

By D. M. Ziebarth

"Normal sequence of operations to develop a new underground mine is: construct and outfit headframe for shaft sinking, sink shaft, construct and outfit shaft sump, develop shaft station and shaft bottom steel. In an effort to reduce the overall project schedule, an innovative plan was developed to install service shaft steel below station level, prior to the completion of the shaft sinking effort. To better evaluate the construction of this substantial steel tower, a preliminary constructability evaluation was conducted, including the best method of supporting the main tower; from the bottom, middle or top of the tower. The design criteria and plan involved: •,Develop access from existing service shaft, 25 km underground •,Use of materials to maximize strength while minimizing corrosion exposure •,Estimating the location of the shaft centerline •,Over excavating the station and shaft below station to allow future shaft steel repositioning •,Designing the tower steel for modular installation •,Incorporate commissioning considerations, such as suspension of the cheese weights during steel installation •,Provision for covered stair access to shaft bottom •,Enclosed shaft envelope with open panels to allow visibility and ventilation The design approach was innovative and this paper will describe the design principles and challenges encountered while providing insight into the solutions developed and implemented; especially the modular construction and installation methodology. INTRODUCTION In an effort to expand the mining operations, a plan was developed to construct a new service shaft closer to the new mine workings and convert the existing service shaft to a production shaft at the Potash Corporation of Saskatchewan Inc. (PCS now Nutrien) Rocanville Potash mine in southeast Saskatchewan. The new service shaft required a multi roped friction hoist operating a cage / counterweight, rope guided conveyances to support the operational requirements. The service shaft is an integral part of the mining infrastructure as it provides access to the underground workings, transport personnel and materials underground for operation and maintenance of the mine. The shaft also allows for services required for safe operation of the underground mine, power supply, controls, communication, dewatering and fresh water supply."

Jan 1, 2019

By Douglas Brand

"The data that many mineral processing plants make use of, is provided by samples taken from sampling systems which are inadequately designed or improperly maintained, and therefore cause detrimental effects to plant operations, production planning and metallurgical accounting! Poorly designed or maintained sampling systems will likely produce low probability samples which give the operator a false sense of security of the product and the process. If data is the basis for action (Flintoff, 1992, p.2), then using the resulting suspect or bad assays by operators, control systems, or metallurgist and administration personnel will act and make decisions which may adversely affect the profitability of a processing plant. Here we will discuss some of the fundamental sampling problems, propagation of errors and a method to estimate what impact this has on an operations Net Smelter Return.INTRODUCTIONIn order to control a mineral processing plant at its best potential, it is necessary to obtain the best possible measurement results of the metal or mineral in question. The sample which is delivered to a measuring instrument, or lab, needs to be of the highest probability to be able to achieve this. This paper will discuss the effects of sampling errors on grade / recovery and grade / Net Smelter Return (NSR) and provide a method to estimate the monetary advantages of using probabilistic sampling in a processing plant.REVIEW OF SAMPLINGSampling, by definition, is the removal of a small representative portion from a total consignment, or flow, for the purpose of accounting or process control.• A sample can only be considered representative, if each and every increment collected, in each of the sampling stages, is representative.• Each particle of the sampling lot must have the same probability of being included in the final sample.• If both of the above conditions are met, then the final sample will be representative of the complete sampling lot.It is commonly known that in order to take truly representative and probabilistic sample, best practices indicate that:• The total stream should be sampled.• The sample cutter should intersect the sample at right angles to the flow.• The sample cutter should travel through the stream at a linear and constant speed and the speed deviations should be less than 5%."

Jan 1, 2016

"A numerical procedure based on Smoothed Particle Hydrodynamics (SPH) is developed for rock blasting phenomena involving multiple intersecting joints. In this procedure, an elasto-plastic damage constitutive model has been applied in the framework of SPH to simulate yielding response of the surrounding rock medium. In this paper, a square shape rock medium with centrally located emulsion explosive in a borehole is numerically blasted with and without the presence of two diagonal rock joints. The model is simulated by assuming all four sides of the rock medium as free surfaces. The paper elaborates the propagation of stress wave, expansion dynamics of gaseous products, and development of fracture, fragmentation of the medium and dissipation of energy due to damage.INTRODUCTIONDamage prediction of rock mass and its mean fragmentation size are of important to design blast parameters for a given explosive. Current blasting practice solely depends on empirical relationships between fragmentation sizes to those blast design parameters while mathematical descriptions of the physical laws governing the process of rock blasting are limited. A constitutive relationship based on properties of explosives and rock mass is of special interest because of its capabilities in describing the key features of rock fracture and fragmentation, resulting in understanding of the physical process involved in rock blasting. It is well known that blast-induced damage and fragmentation of rock mass occur due to detonation induced stress wave and product gas driven fracture propagation. Nevertheless, the fundamental mechanism of the failure process and the behavior of rock characteristics under these two different loading are not well understood in many cases, which are closely related to growth of fractures and interaction of cracks under different loading conditions.Continuum damage mechanics is considered to be appropriate to describe the failure process under such high-amplitude stress wave. Based on this approach, several theoretical models have been developed to analyze the dynamic damage of brittle material such as rock and concrete with microstructure (Chen, 1999; Taylor et al., 1986; Wu et al., 2004; Yazdchi et al., 1996). These models are mostly based on the theory of damage mechanics or fracture mechanics with some statistical treatment to incorporate random distribution of microcracks. In the application of fracture mechanics theory, sometimes it is difficult to estimate the micromechanical parameters such as crack density and fracture toughness in different modes. In this study, damage in rock material is evaluated according to the earlier model developed by Grady and Kipp (1980), which is a fracture model coupled with a material description for stress wave propagation to predict quantitatively fracture and fragmentation under explosive loading conditions."

Jan 1, 2015

By R. C. Rowe

THIS paper is an endeavour to analyse the ideal and practical functions of government technical mining services, and their relationship to the National Domain, as well as to one another. its spirit is not critical, even though at times it may appear to besoin fact. It is a serious effort to divert a trend in public thought which delights in calling itself practical whereas it is really merely short-sighted. The author refers particularly to the idea that governmental research is a luxury which should be curtailed in the interests of economy, and turned over to private enterprise or the provinces. In order that we obtain the proper perspective of the question, it is advisable to indulge in a little history. In the year 1842, the Geological Survey of Canada was formed under the guidance of William (later Sir William) Edmund Logan. The literature on the founding and history of the Geological Survey of Canada is extensive, and therefore it is unnecessary to go into detail here regarding it. It might be mentioned, however, that the Geological Survey of Canada is only seven years younger than the Geological Survey of Great Britain (founded in 1835), and is only exceeded in age on the American continent by the State Geological Surveys of New York, Pennsylvania, Massachusetts, and Michigan, which were founded between 1833 and 1836. In 1877, the Geological Survey became a permanent government institution as a branch of the Department of the Interior. It should be noted, however, that the Director of the Survey ranked as a Deputy Minister and reported direct to the Minister. This continued until 1907. In 1886, the Mineral Resources and Statistics Division of the Geological Survey was formed. Some years later, the Canadian Institute of Mining and Metallurgy (then the Canadian Mining Institute), backed by the mining press, began to agitate for the establishment of a Dominion Department of Mines, and in 1907 such a department was founded by the Geology and Mines Act of that year, with a separate Cabinet portfolio for the position of Minister of Mines.

Jan 1, 1939

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By J. Sliwinski, H. Kikutani, J. Atwood, D. Larimer, J. Pyecha

"The Pogo mine start-up milling targets of 2005 are vastly different than the targets of today. Improvements have been driven by unintentional design oversight, continual circuit optimization or optimization due to changing mineralogy. The more significant process improvements to date have occurred in the gravity, flotation and leach/CIP unit operations. Details of the significant improvements are presented along with the impacts to the process.INTRODUCTION Deposit Overview Pogo mine is located along the Goodpaster River, southeast of Fairbanks, Alaska. This deposit sits in the center of the Tintina Gold Province (Figure 1), a region of similar Intrusion Related Gold deposits in Interior Alaska, the Yukon and British Columbia Canada (McCoy et al., 1997). The Pogo deposit is hosted in a rock sequence of amphibolite-grade gneisses intruded by mid-Cretaceous granitic plutons and dikes, which in turn, were cut by and host the auriferous quartz veins of the Pogo deposit.The Pogo deposit is comprised of three distinct zones of auriferous quartz veins spatially adjacent to each other. These are the Liese Zone, North Zone, and the East Deep Zone. The Liese Zone consists of three stacked, massive quartz veins, designated the L1, L2, and L3. Vein thickness averages 3.0 m, with variations from 0.3–18 m thick. The North Zone mineralization is comprised of four veins with more consistent thickness, between 1 and 1.5 m. The East Deep deposit lies northeast of the Liese Zone ore body. It is separated by a post mineralization, quartz diorite pluton. The East Deep Zone is comprised of two stacked massive quartz veins with similar orientation as the Liese Zone."

Jan 1, 2017

By A. Grimod

Rockfall drapery systems are commonly used as a simple, fast and cheap measure against the rock falling trajectories affecting very steep slopes. The system basically consists of a steel mesh, which is held on the top edge with a longitudinal cable fixed by means of a suitable number of anchors. The effect of this kind of intervention is to control the falls of the rocks, which are driven toward the bottom with slow velocity, or are stabilized on place. It can be used on any kind of slope to protect sensitive target in the mining industry, roads and railways, and inhabited areas. The falling blocks, typically smaller than 0.6 - 1.0 m in diameter, pile up into a trench (or into a ?pocket of mesh?) at the bottom. In comparison to other types of rockfall interventions, the simple drapery is cheaper, and its maintenance is easier, but on the other hand it cannot be considered the remedy for shallow instabilities, because it can only mitigate the effect of the falling trajectories. The design of simple draperies requires the analysis of several factors like the slope features (height, gradient, morphology), the geological and dynamic features (nature of the ground or rock, type of instability, erosion problem, blocks size), the environmental condition (presence of vegetation, aesthetical problem), the installation problem (accesses to the slope, safety for the workers, safety for the surrounding areas) and finally the performance required (temporary or permanent intervention, required maintenance, cost). Finally the most problematic design-step is the choice of the suitable mesh, the top longitudinal cable, and the top anchors type. Because of the highly variable nature of rockfall behaviour these structures cannot be standardized, but they have to be analyzed and designed for each case. Maccaferri has developed a new software application (MacRO 2) has a practical tool to define the mesh and the related supporting structure composed by up-slope cable and anchors. The software, based on the approach proposed by Muhunthan B. et al. (2005), allows designers to verify the top longitudinal cable, the anchors, and the mesh drapery, and to plan for maintenance procedures. Even if the method seems quite simple and rough, it is effective and lets the designer correctly foresee the materials and the geometrical features to be used on the interventions. This paper analyses the condition for the simple drapery installation, the main steps for the calculations, and it will present a case study in a U.S. mine. Nevertheless, even if the software allows a quick and simple calculation approach, onsite observations are always recommended in order to achieve a good design, with the ultimate goal of protecting property and human lives.

Aug 1, 2013

By K. Adham

Iron chloride pyrohydrolysis (ICP) is used as an efficient way to fix iron as an oxide, for sale as a by-product or for safe disposal. Iron chloride is reacted with water at elevated temperatures to yield iron oxide and hydrogen chloride. Both the steel industry and synthetic rutile producers make extensive use of ICP. Two technologies are available for ICP: fluidized bed (FB) and spray roaster (SR). Both technologies are energy intensive. Here, fluid beds and spray roasters are compared with respect to their fuel and electrical energy consumptions. Roaster size and oxide product characteristics are also considered. Process models are prepared, using the METSIM® software, and specific energy consumptions are compared. The results will help the industry decide which technology best suits its goals and at what energy cost.

Jan 1, 2006

The mining industry has generally been slow to apply ion exchange processes to hydrometallurgical applications even if ion exchange offers an ideal solution for a particular problem. Two notable exceptions are in gold and uranium recovery. The largest application of ion exchange in the metals processing industry has been the use of resin-in-pulp (RIP) for gold recovery as an alternative to activated carbon. Iron is a ubiquitous impurity in hydrometallurgical solutions. In many cases, bulk removal of iron from the process solutions is accomplished by precipitation. However, precipitation for iron control is often accompanied by losses of base metals by co-precipitation. Increasingly, the option of ion exchange for removal of smaller amounts of iron from process solutions has been favoured. A number of applications have been developed and proven at the commercial scale for the removal/control of iron from a range of metal processing solutions. This paper provides an overview of the application of ion exchange for iron removal from a range of metal processing operations, including Cu, Ni and Co solutions. A number of case studies are provided which review operational and resin regeneration strategies and the impact upon the commercial operation of metal processing with improved iron control.

Jan 1, 2006

By Christopher Andreae

Years before iron and steel works were established at Sydney, several thriving although short-lived iron works operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron works. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principal fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel works dominated production for Nova Scotia and the rest of Canada. Two sites achieved prominence in the nineteenthcentury Nova Scotia iron industry: Londonderry and Ferrona (Fig. 1). Londonderry, the larger and longerlasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace. But once the furnace was blown out in 1904, the population gradually drifted away.

Jan 1, 1999

By Yi Yang, Mark Zoback

"We report laboratory studies of the time-dependent deformation of core samples from four different formations in the Williston Basin - the Lodgepole formation, the Middle and Lower Bakken formations and Three Forks formation. The laboratory tests reveal varying amounts of viscoplastic deformation in response to applied differential stress. The time-dependent deformation is generally greater in rocks with higher clay and organic content, and can be described by a power-law function. Because the magnitude of the creep strain is linearly proportional to the applied differential stress, we can utilize viscoelastic theory and geophysical logs to estimate the degree to which tectonic stress is affected by viscoplastic stress relaxation. We suggest that viscoplastic stress relaxation results in the Upper and Lower Bakken Formations act as frac barriers during hydraulic fracture stimulation in the Middle Bakken, but the Lodgepole and the Three Forks Formations are not frac barriers.INTRODUCTIONHorizontal drilling and multi-stage hydraulic fracturing in shale reservoirs are critical for successful exploitation of ultra-low permeability shale gas, tight gas and shale oil reservoirs. Characterization of the mechanical properties of the reservoir rocks is essential to understanding the behavior of rocks during drilling and completion. Previous laboratory studies have shown that the timedependent deformation in clay-rich shales can be characterized as linear/viscoelastic deformation (Chang et al., 1997; Hagin and Zoback, 2004a, b; Sone and Zoback, 2013b, 2013c). Sone and Zoback (2013c) showed that laboratory measurements of time-dependent deformation in various gas shale reservoir rocks, and demonstrated that the viscoplastic deformation of these rocks can be characterized by a power-law function. They interpreted the results in the framework of linear viscoelastic theory to quantitatively assess the geomechanical effect of viscous time-dependent deformation over engineering and geological time scales. (Sone and Zoback, 2014) further extended the theory and proposed a viscous relaxation model that can be applied to predict the continuous differential stress magnitude using the geophysical logs. They tested the validity of their model by comparing the stress prediction with the occurrence of drilling induced tensile fractures (DITFs) and the vertical hydraulic fracture penetration observed from microseismicity."

Jan 1, 2015

By W. R. Tyson

Imperfections such as lack-of-fusion and undercut are inevitable in field welding of pipelines. Above a certain size, such defects must be removed or repaired. In the present state of the art, determination of allowable defect size is done by Engineering Critical Assessment (ECA). This requires measurement of toughness, and comparison of toughness with crack driving force. ECA methods used in current international pipeline standards will be reviewed and compared.

Jan 1, 2010

By Marketa D. Evans

The mining industry has a significant opportunity to capitalize on its past learnings in order to build better social relationships. The industry?s relationship with society is both critical and under pressure. Rising levels of public opposition and social conflict are already having material impacts on operations around the world. Industry has an opportunity to shape the future direction of this social engagement, build public trust and proactively respond to a material risk to operations, but first it needs to better understand the nature of the challenges and the urgency of addressing them.

Aug 1, 2013

By Curtin University Western Australian School Mines

"Curtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc.) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The model structure, modelling approach, and some scenarios are discussed.INTRODUCTIONCurtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. The model has recently been upgraded to include an integrated liberation-leach modelling (ILLM) approach. The ILLM approach provides the means to evaluate the impact of the gravity recoverable gold (GRG) characteristics of the ore (GRG content and liberation behaviour), various process parameters (such as grind size, bleed to gravity, etc.) and circuit configurations on the gravity gold recovery, leachadsorption circuit behaviour and overall plant gold recovery.A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach. The data required for the ILLM calibration can be obtained directly from the 3 stage GRG test, leach tests and size-by-assay analysis of the 3 stage GRG test products, and leach test products.This paper describes the ore characterisation methodology, model structure, modelling approach, and the application of the ILLM."

Jan 1, 2016

By C. Riveros, H. Henein

Bulk Metallic Glasses have a high potential as advanced engineering materials due to their various properties including strength and corrosion resistance, to name a few. This paper investigates amorphous phase formation and rapid solidification characteristics of impulse atomized Co-based alloys in order to understand and control the application properties of the final products. Amorphous fraction and kinetic crystallization properties of the atomized Co-based alloy powders were quantified by means of Differential Scanning Calorimetry. In addition, different but complementary characterization tools were used to analyze microstructures of the powders. These include optical microscopy, X-ray diffraction and micro-hardness tests. While the amorphous fraction within the powders is promoted by high cooling rate and smaller powder size as expected, hardness is found to decrease with the fraction of amorphous phase.

Jan 1, 2015

By A. L. Valdivieso

"The correlation obtained by plotting pH of maximum adsorption of dextrin versus the isoelectric point of involved metal hydroxides can be used to predict the depressing effect of dextrin on flotation in ""pure"" sulfide mineral systems. Sulfides are strongly depressed by dextrin whenever their surfaces are coated by the corresponding metal hydroxide. The efficiency of dextrin as a depressant is affected by the adsorption of the sulfhydryl collector. Hydrolyzable cations modify this relationship in flotation of sulfide ores. This type of deviation of the real-life systems from the predictions based on the behavior of the pure systems shows the possible ways that could be followed to further improve the obtained correlations. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by"

Jan 1, 2009