Search Documents

By R. A. Kipp

THE dry concentration of ores and minerals is a subject on which there is very little engineering literature available. With the advent of flotation, practically all milling research was turned to this development as it held the answer to large-scale economic operations. However, there are many concentration problems that can be more adequately and economically handled by the dry methods that have been developed, and, consequently, I believe it is very advisable for mining men to become fully 'conversant with just what can be done in the dry state. Therefore, today, I should like to give a brief summary of the processes that are available and, in a general way, how they can be a p-p lied. I shall confine my remarks mainly to two dry processes: THE Am FLOTA'l'ION TABLE AND THE ELECTROSTATIC SEPARATOR Dry Magnetic Separators should probably also be included, but I am

Jan 1, 1961

By H. B. Lumsden

This paper is intended to deal merely with the commercial development of some of the principal non-metallic mineral resources in the three prairie provinces- Manitoba, Saskatchewan, and Alberta. Coal is not included in this summary. Building Stone First and foremost, mention may be made of the building stone now being produced at Tyndall, Manitoba. This is a mottled limestone and is declared by experts to be one of the finest building stones in America, both as regards durability and appearance. It has been used very extensively both for exterior and interior work, not only in western Canada, but also in the principal cities as far east as Montreal. The stone is the "'Upper Mottled Limestone", which forms the summit of the Trenton (Ordovician) strata in the Lake Winnipeg basin. Quarries are at present being operated at Garson and Tyndall . The area where this stone is known to be available extends in a north and south direction for a distance of three miles, and the main productive ridge is probably about one half mile wide. The outlook for the future of the industry is extremely promising, as the stone is becoming increasingly popular in Eastern Canada, more particularly for interior work.

Jan 1, 1928

By L. M. Scovell

The Internet and its related technologies will radically change the way that mines manage and control their maintenance, repair, and operating supply chains. The Internet is creating new distribution channels and offers new technology platforms with significant advantages over more traditional methods. Mines will have to re-evaluate both the strategies and the tactics employed in these areas. Mines will use e-commerce to integrate their maintenance, repair, and operating supply chains. The integration will extend beyond traditional trading partners to a worldwide network of communities with similar interests and goals. The changes will transform the way mines operate, lower mining costs, and thereby increase their chances of success in an increasingly competitive environment.

Jan 1, 2000

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By F. Doxey

Introduction In order to improve outputs and to reduce or hold mining costs, many attempts have been made to mechanize the getting and loading of coal in the major coal producing countries, and machines of various kinds and sizes have been designed and manufactured. Some of the most important are: Joy Continuous Miner Joy Coal Auger Goodman Mining Machine Lee-Norse Koal-Master Jeffrey Colmol Cardox Hordsecg Recovery Drill German Coal Plough British Coal Plough with agitated blades M. & C. Samson Stripper AB Meco-Moore Cutter Loader Joy Gloucester Getter The three last named are the chief longwall machines in use and the AB Meco-Moore and the Samson Stripper are doing a good job in their respective applications. It is understood that the Gloucester Getter recently installed in a British colliery also shows reasonable promise. It was felt, however, that to meet the conditions of the mines in Nova Scotia, any machine developed must have certain distinctive characteristics. It must: ( 1) Be able to cut and deliver coal in quantity and of the right sizes ( 2) Be easily manoeuvrable ( 3) Be suitable for longwall operations ( 4) Not interfere with timbers already set ( 5) Cut its own stable (6) Work on reasonably heavy gradients

Jan 1, 1951

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite's crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

By Heribert F. Broicher

By the very nature of mineral deposits the quality of the raw material generally fluctuates and should be known for optimum processing. Early classification, for example, of limestone into road-metal grade or lime grade or of run-of-mine ores into high grade, low grade and waste as well as information for blending or for dosage of reagents are prerequisite for economic processing. Non-contact, real-time and on-line rock identification or assessment of quality parameters can be realised by introducing the analysis of laser-induced fluorescence (LIF) into the mining industry. LIF analysis is an optical method evaluating the basically known photoluminescence properties of matter, however, extending the application into hitherto unimagined fields by use of high-energy pulsed lasers and time-resolved analysis of fluorescence in the ultra-violet, the visible and near-infrared domains of light. LIF analysers and test work in a limestone quarry and a cement plant in Germany as well as in an iron ore mine in Sweden are described. First results of test work are available and proof this technology to be promissing.

May 1, 2002

By P. Roman, L. Daneshmend

"During the last decade, mining companies have been overwhelmed by technological solutions to perceived problems. This is particularly true with information technology where rapid advances have resulted in a professional climate characterized by technomania — the perception that failure to adopt emerging technologies will result in a loss of competitive advantage. This paper describes the applicability of structured analysis and design techniques as an appropriate methodology for integrating emerging technologies in the mining industry. The potential of this approach to improve overall mine effectiveness through improved communication and co-ordination between operations and maintenance is discussed. IntroductionA strong working relationship between the operations and maintenance departments in both open pit and underground mines is fundamental to the overall success of the mining endeavour. Unfortunately, for many mines, this characterization is far from accurate. Short-range production targets dominate the day-to-day management of the mines. This can be seen in Bostwick and Buchanan’s (1993) report on American Barrick Resources efforts to achieve an aggressive 415 000 tpd mining program at their Goldstrike operation in Nevada. When production managers do not meet their quotas, the finger is often pointed at maintenance. As a result, a confrontational culture can develop between the two organizations, resulting in a lack of cooperation that exacerbates the problem. Historically, production planning has taken priority over maintenance planning. This is reasonable since production is the primary purpose of the mine with maintenance serving in a support role. This basic relationship remains intact today. However, the trends toward mechanization, increasing levels of automation, and larger equipment, have resulted in increased reliance on the equipment used in the mine. As a result, downtime costs now go well beyond the direct labour associated with the repair of the machine. Lost production costs due to downtime resulting from failed equipment are becoming an increasingly important factor in determining a mine’s overall economic performance."

Jan 1, 2001

By A. M. Krzanowski, T. S. Golosinski

"This paper presents results of a study undertaken to determinethe feasibility of mining plains overburdens with bucket wheel excavators. Based on extensive geotechnical testing of overburdens under study, the relations between material geotechnical properties and its cuttability were defined. The properties with the highest correlations to the cuttability werethen used to develop the material diggability classification. This classification may be used for identification of overburdens and coals mineable by bucket wheel excavators.IntroductionLow cost of mining and high productivity can be achieved when mining unconsolidated soils and soft rocks with bucket wheel excavators. As a result this mining equipment will likely be introduced into plains coal mines. At present there are plans to use a bucketwheel excavator (BWE) in at least one mine by the end of this decade. Unfortunately, the performance of a BWE deteriorates rapidly with the increasing strength of mined material. To avoid costly misapplication, material diggability must be defined in advance of an application (i.e. the force required at the cutting edges of BWE buckets must be quantified). Correct definition of material diggability permits reliable selection of a BWE, or may indicate unsuitability of this equipment for a particular application.The reported studyu i was undertaken to investigate the diggability of typical prairie overburdens and thus provide a guidance for likely future applications of bucketwheel equipment. Investigations concentrated on the parts of overburden most likely to create problems for a BWE mining. These are defined in Table 1. At present, thin layers of the two investigated materials (samples K and L) are mined by a BWE in an oil sand mine, after being loosened by blasting."

Jan 1, 1987

By A. Supomo, H. Resendiz, C. Burbidge

"Freeport-McMoRan Inc. (FMI) commissioned the expansion of the Morenci Metcalf concentrator in 2014. The concentrator included many design and equipment innovations, including the first-of-its-kind Metso Hydraulic Roll Crusher (HRC), variable speed ball mills and variable speed crushers. In addition to the innovative design, FMI commissioned the Metso APC team to design a realistic process simulator and the plant APC. The process simulator was utilized to train operators before commissioning, which led to a smoother plant start up. The plant APC utilized the concept of dynamic constraint control, which controls the feed to the primary ball mills by “pulling” the tons from crushed rock storage bins, which then automatically are filled by the upstream HRC and secondary crushing circuits. The primary ball-mill control also adjusts the water addition to the cyclone clusters to avoid overload and achieve sufficient grind size. The constraints include in-circuit constraints for feeder capacity, screen-deck capacity, ball mill power, cyclone mass flow, pump capacity and pump motor capacity. The APC system was implemented shortly after the start of commissioning and immediately demonstrated increased throughput and an ability to highlight and quantify process constraints and bottlenecks. The following paper outlines the control strategy, discusses system implementation, results and challenges.INTRODUCTION The FMI Metcalf Concentrator is located in Morenci Arizona on the site of the old original Concentrator. The new Metcalf concentrator started operation in May of 2014. This plant was designed for an average of 63,500 tpd (70,000 stpd), increasing the total Morenci concentrator complex production to a nominal 113,400 tpd (125,000 stpd). The process flow diagram is shown below in Figure 1.The process consists of primary crushing feeding a coarse ore stockpile followed by secondary crushing operating in closed circuit with vibrating screen decks. The screen undersize feeds the first of its kind Metso hydraulic roll crusher (HRC) operating in a closed circuit with vibrating screens. The primary crusher is a Metso 60x110 gyratory crusher. Secondary crushers are Metso MP1250 Crushers with variable speed drives. Secondary crusher discharge is recycled to the dry screen feed bin and screened with oversize returning to secondary crushing and undersize feeding the Metso HRC3000. The product from the 3.0 meter X 2.0 meter roll crusher is wet screened with the undersize feeding the grinding circuit, which is comprised of two each 24-foot diameter by 40- foot-long variable speed ball mills running in parallel with each in closed circuit with a cyclone bank of 12 cyclones. The wet screen oversize is recycled to the HRC feed bin."

Jan 1, 2019

By W. F. MacIsaac

"The large low-grade Copper Mountain deposit is located in the northern portion of the Gaspé Cooper Mines property. It is approximately 1 mile north of the Needle Mountain deposit. The orebody outlined to date lies in the top 1,000 feet of the Grande Greve formation. Chalcopyrite occurs in association with pyrite and quartz in small veinlets and numerous fractures. The deposit is immediately adjacent and parallel to a quartz-feldspar dyke and may be associated with a nearby porphyry stock. Stratigraphy, alteration and structure appear to have played an important role in ore deposition."

Jan 1, 1969

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By Philippe V. Scheers

Polycrystalline gold, glassy carbon and gold-activated glassy carbon electrodes were compared for the production of hydrogen peroxide by the cathodic reduction of dissolved oxygen. Gold was deposited on glassy carbon by sputtering with a sputter coater and by electrodeposition from a diluted KAuCl4 solution using short potential steps. The sputtered gold particles were not adherent enough, but there were no adhesion problems with the electrodeposited gold particles. The gold coverage of the glassy carbon surface could be varied by applying a different number of potential steps. The overpotential for the electroreduction of oxygen to hydrogen peroxide decreases with increasing gold coverage of the glassy carbon surface, and for gold coverages exceeding about 16 %, the overpotential is close to that observed on polycrystalline gold.

Oct 1, 2003

By A. Warczokand

The cleaning of copper smelting slag requires magnetite and cuprous oxide reduction. The slag reduction with coke, injected coal powder or bunker oil is strongly endothermic and requires heat generation by fuel combustion or the use of electric energy. The reduction of fayalitic slag with calcium carbide is slightly exothermic and the formed calcium silicate modifies the slag. Thus, the additional energy is required only for covering furnace heat losses. Results of crucible scale tests showed the rate of slag reduction approximately five times higher in comparison of the slag reduction with coke under the same conditions. It seems that the effect of exothermic reaction and slag modification with CaO at the reaction interface results in very high rate of slag reduction. Industrial scale tests carried out in the Anglo-American Chagres Smelter demonstrated the possibilities of effective reduction and cleaning of the slags from a flash smelter and Peirce-Smith converters in a Teniente Slag Cleaning Furnace. The slag reduction was carried out without any reductant or stirring gas injection, simply by calcium carbide charging through a furnace mouth, and was very fast.

Jan 1, 2007

By George A. Guess

The making of contracts for the purchase of ores is a business which the metallurgist usually understands better than the miner. Companies in the custom ore business often employ an ore buyer who is aware of the class of ore which the smelter needs, and is thoroughly conversant with the business. The miner on the other hand makes ore contracts but seldom, and it is often only after a settlement has been made that he realizes the meaning of the terms of the contract under which he has sold his ores. He has expectations usually greatly in excess of the amount 'net proceeds' shown at the bottom of the settlement sheet. Seldom does the occasional shipper really know his contract. A somewhat similar parallel is to be found in insurance policies. We all have insurance policies; we never know the conditions contained in them until after the fire. The clauses in the policy are for the protection of the Insurance Company. An Insurance Company has no friends.

Jan 1, 1926

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By Paul B. Warrington

This paper presents a discussion of the factors affecting copper scrap markets, including such items as price levels, freight. grades of material, sources and packaging. Reference will also be made to the effective life and turn-around of the copper content of some products. Introduction IN TERMS OF SIZE, copper scrap is second only to ferrous scrap in tonnage recycled. However, in total value, it is second to none. For example, world scrap recovery during the preceding 4 years averaged just under 2,300,000 metric tons per annum, and at an average price of 70 ¢ a pound, this works out at a turnover of about $3.5 billion, which indicates that the copper scrap industry, or recycling as it is now becoming known , is a substantial one.

Jan 1, 1977

By R. P. Charbonnier

"To understand the operation of jigs and other separating processes based on differences in gravity, it is desirable to analyse the motion of various particles in given media under specific conditions. A summary of the earlier theories shows that they lead to unsatisfactory or excessively complicated formulae in cases such as coal jigging. By adopting a simplified theory of the motion of particles in a fluid, the size and duration of the initial accelerated motion of a particle falling in hindered settling can be calculated. Based on this mathematical analysis, examples referring to actual coal jigging practice show that it is desirable to prolong and/or repeat, as frequently as possible, the optimum conditions corresponding to an effective acceleration of the particles. The separation is then obtained according to gravity rather than to particle dimensions, as would be the case if the velocity of the particles• were allowed to approach its terminal value. To achieve this gravity separation, it is suggested that the suction phase of the jigging cycle be artificially prolonged and the frequency of pulsations increased as much as possible for washing the coals of smaller sizes."

Jan 1, 1959

By J. Someehneshin

Nowadays along with population growth, industry development, consumption of mineral resources and the fact that the reserves on hand are running out, the depth of surface and underground mines for further exploitation are increasing. During recent years, in underground mining, the block caving method for low-grade and large-scale deposits has shown a growing rate of application. This method is very cost effective and economically affordable. The dimensions of blocks are one of the most important parameters which should be taken into account since it has been proved to have a great deal of effect on technical issues such as commencement of caving and mine design. Proper calculation of the length and width for a block in this method leads to proper caving and discharging which are the most important stages. Therefore, in this method, the calculation of the optimized dimensions (length and width) of blocks is not only important but also directly helps the productivity of extraction. In this study, firstly for the purpose of facilitation, some assumptions were considered and having used these assumptions for estimation of optimized length and width of block, a relationship based on rock mechanics and physics was explored. Furthermore, some necessary details were added to the said relationship and finally, it was transformed into an inequality. Solving this inequality provides us with the optimized length and width of the block. The explored relationship was analyzed with MATLAB software and the graphs thereof were drawn. In these graphs, each time one of the input parameters has been drawn up in a logical range so that it could be compared with previous states.

Aug 1, 2013

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010