Search Documents

By R. Wirth, B. Orberger, C. Wagner, A. Tudryn, B. Baptiste, S. Miska, Université Paris-Sud

Banded iron formations (BIFs) comprise complex textures and mineralogy, which result from fluid-rock interactions related to high and low temperature alteration. The initial iron oxy hydroxide mineralogy and associated phases such as carbonates, quartz, apatite and phyllosilicates were transformed leading to an upgrading of these BIFs into the world’s largest source of iron ore. In low-grade BIFs, a large part of the iron is related to micro- and nano- metric iron-bearing inclusions within micrometric quartz and/or carbonates (mainly dolomite). We studied laminated jaspilitic BIF samples from a drill core containing 26.71 wt.% total iron, 0.2 wt.% SiO2, 0.32 wt.% MnO, 15.46 wt.% MgO, 22.32 wt.% CaO, 0.09 wt.% P2O5, < 0.05 wt.% Al2O3, 0.15 wt.% H2O and 34.08 wt.% CO2 (Aguas Claras Mine, Quadrilatero Ferrifero, Brazil). Bright rose coloured dolomite and quartz bands alternate with massive specular hematite bands. Raman spectroscopy, X-ray diffraction and FIB-TEM analyses reveal that the micro- and nanometric inclusions in dolomite are mainly hematite and minor goethite, partly occurring as clusters in voids. Curie Balance analyses were carried out at different heating steps and temperatures on whole rock samples and a synthetic mix of decarbonated sample and pure dolomite. X-ray diffraction on the products of the heating experiments shows that that hematite is stable and new phases: magnesioferrite (MgFe2O4), lime (CaO), periclase (MgO), portlandite (Ca(OH)2) and srebrodoskite (Ca2Fe2O5) were formed between 680°C and 920°C. These finding gives hints to optimizing the beneficiation process, as the presence of hydroxyl ions bearing goethite micro- and nanoinclusions lowers the sintering temperature. Prior separation of coarse hematite and barren dolomite and quartz, followed by lower temperature sintering of the inclusionbearing dolomite/quartz leads to transformations into phases with higher magnetic susceptibilities (such as hematite and magnesioferrite). The entire Fe and Fe/Mg oxide feed (the priorly separated fraction added to the sintered fraction) can then pass through wet-high intensity magnetic separation after crushing.

Jan 1, 2016

By Sylvie Lévesque, Frederic Couët, Laura Pérez-Barnuevo, Cory Hennessey

Determining mineralogical characteristics of samples throughout the iron ore concentration process – from drill core samples up to the concentrate – is critical to process improvement and remediation. However, assessment of mineral proportions, liberation, and texture, although essential, can be time-consuming and costly. Thus, a mineralogical study is often not performed or only restricted to a limited number of samples. New iron ore deposits or new ore zones in active mines will bring new challenges as they are known to be problematic due to their lower grades, complex textures and presence of mineral impurities. In those cases, applied process mineralogy will be necessary to understand and to diagnose potential processing issues. To take full advantage of mineralogical information along the iron ore concentration process, new tools are being developed to provide mineralogical data based on texture, composition and liberation. In an early stage at the mine, the automated identification of drill core textures could provide essential information for the prediction of ore concentrability and grindability. In a later stage, the automated modal tool, combining the knowledge of the iron ore mineralogy of a specific deposit and the results of chemical analyses, can quantify the mineral proportions of the ore; results show good agreement between mineral estimation via chemical analysis and modal analysis using a Mineral Liberation Analyser. A bulk mineralogical analyser allowing semi-quantitative evaluation of the liberation of iron oxides is being validated. The results from the bulk mineralogical analyser will eventually be linked with the mineral proportions issued by the automated modal tool to provide complete mineralogical characteristics of iron ore samples. Ultimately, these mineralogical tools could provide valuable and timely insight for predicting concentrators’ performances or troubleshooting gravity separation processes.

Jan 1, 2016

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By W E. vanSteenburgh

The Polar Continental Shelf Project was initiated in 1959 to provide an administrative and logistic vehicle for research in the physical sciences of the land, sea and channel area of the Arctic Archipelago. Most of the scientists are supplied on secondment from the professional branches of the Department. The yearly expeditions number some eighty scientists and sub-professional staff, and they are supported by a fleet of fixed-winged aircraft and helicopters. Accurate positioning is obtained by the use of a Decca Lambda navigational system which is moved as the area of interest is shifted. The Project is designed to accommodate not only physical scientists, but to provide facilities for other scientist who may have an interest in the area under study. The main research scope of the Project includes topographical surveys, hydrography, oceanography, geology, including marine sedimentary studies, gravity, magnetics, seismology, glaciology and geography. The Polar Continental Shelf Project was initiated and recommended by the Committee on Northern Development in 1958.

Jan 1, 1963

By John G. McCamis

The Maritimes Carboniferous Basin is the largest intermontane basin in the Appalachian Mountain System, occupying a total area of 57,200 square miles and containing up to 30,000 feet of late Devonian through Permian .sediments. Deposition began with continental elastics in late Devonian and early Mississippian. Marine deposition is represented by a limestone-evaporite sequence of late Mississippian age. Pennsylvanian and Permian continental rocks deposited largely in flood-plain and swamp environments complete the succession. Marine seismic data disclose several varieties of structure, both halokinetic and tectonic in origin. Recent exploratory drilling in the offshore part of the Basin encountered good reservoir rocks in the Riversdale sandstones, which also provided encouraging shows. The most likely source rocks of hydro~ arbons in the Maritimes Basin are shales in the Horton and Riversdale groups. Potential recoverable reserves of the Maritimes Basin are estimated to be 400 million barrels of oil or 7.8 trillion cubic feet of gas, based on the volume-of-sediment method of calculation.

Jan 1, 1973

By John S. Stevenson

THE Twin "J" Mine, operated by Twin "J" Mines, Limited, represents an amalgamation of the old Lenora, Tyee, and Richard III mines (see Figure 1) on mount Sicker, eight miles by road, northwesterly, from the city of Duncan, on Vancouver island. These mines produced 253,000 tons of copper-gold ore between 1898 and 1909 (see Table I). During the more recent period of production from these properties, July, 1943, to May, 1944, Twin ?J? Mines, Limited, mined and milled ore with values mainly in copper and zinc, and minor values in gold, silver, and lead. Figures are not available for this later production. Field work at the property was started by the writer in 1941 and continued in 1943 and 1944.

Jan 1, 1945

By Richard Stewart

There are highly competitive world markets in most of the minerals being mined today. The high standard of living we enjoy in North America results in ever increasing productivity through mechanization and automation. Conventional underground and open-pit mining practices throughout the world are constantly changing to reflect the engineering advances of our technology. New records in tunneling, shaft sinking and excavating are being established. Larger and faster equipment is in production. Mining operations are being studied in detail to improve materials, methods and machines. Standards and controls are being established to measure the performance of people and equipment. These steps all tend to improve our present performance. In addition to these short-range improvements, however, there are the basic research and applied research studies which are aimed at developing entirely new approaches to our mining problems. Basic research in rock mechanics is coupled with applied research in rock penetration, fragmentation and stabilization.

Jan 1, 1963

By F. C. Grensing, W. R. Crib

Copper-15 Nickel-8 Tin alloy is a relatively modern material, having been discovered in the 1970’s. It has complexities with casting, hot working and interdependent solid state phase transformations. A key to the high reliability manufacture of wrought rods, bars, plates and tube is the casting technology, which limits segregation, promotes microstructural uniformity and enables hot working. The EquaCast® continuous casting process has enabled the production of a broadening variety of wrought forms with typical yield strengths ranging from 100 to 180 ksi (690 to 1241 MPa) depending on size, shape and temper. This paper reviews the characteristics of wrought Copper-15 Nickel-8 Tin products which have registration in AMS specifications (4596 and 4597) and MMPDS-04 (CN-1) for use in aircraft. The design limits, microstructures, fracture characteristics and tribological behavior will be examined. This alloy system is emerging as a material of choice for aircraft bearings, corrosion resistant oil and gas exploration components, machinery and demanding off-road equipment applications. ToughMet® 3 is an alternative or upgrade to conventional moderate and high strength aluminum bronze bearing alloys.

Jan 1, 2010

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By Peter M. Power

A microscopic study was made of a series of simultaneous slag and metal samples taken from a low carbon basic open hearth heat. An attempt was made to identify the various micro-constituents found. As the various impurities in the bath are oxidized, the metal structure changes from that of high-phosphorus white cast iron to that of low.-carbon steel. A detailed study of phosphorus distribution is included. The acid run-off slag has an .acicular orthosilicate structure which changes on &apos;shape-up&apos; to a very basic tri-calcium silicate and calciuim ferrite structure. Many unidentified minor constituents are present in the slags. Though metallography will never replace chemic.al analysis of the bath, the microsopic study of polished slags has some promise of being useful in slag control work.

Jan 1, 1956

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By J. M. Cummings

The importance of controlled sand properties to the production of quality castings has been recognized by foundry men for many years, but the maintenance of requisite standards results in a relatively high sand consumption, which in steel foundries, for instance, may range from half a ton to over one ton of sand per ton of finished casting. During the war, obtaining and maintaining adequate sand supplies became a serious problem in many foundries, owing to increased wartime production and serious &apos;bottlenecks&apos; in transportation. As a result, considerable interest was aroused in the possibilities of various sand reclamation systems by which up to 85 or 90 percent of discarded sand may be returned to a usable condition. During the past five years or so, a number of sand recovery installations have been made by both ferrous and non-ferrous foundries in Canada and the United States, and have resulted in substantial reductions in sand costs in every case. The possible benefits of sand reclamation are particularly apparent in British Columbia where no suitable sands for steel and heavy iron foundries occur naturally, and where freight costs on imported sands are considerably higher than initial selling prices. This is well illustrated by the fact that silica sand, which sells for about $2.00 per ton at pits in Illinois, is laid clown in British Columbia for around $11.00 or $12.00 per ton. The operating costs quoted for certain of the reclamation schemes, i.e. $0.25 to $1.50 per ton, may actually be no higher than the cost of waste sand disposal in city-located foundries. In view of the foregoing considerations, the British Columbia Research Council has undertaken a study of the possibilities for sand reclamation, with particular attention directed to its application in local steel foundries. No commercial occurrences of silica sand are known in the Province, and, with this in view, the Council previously investigated the possibility of recovering silica sand from local impure sands. Results were definitely encouraging, but it was felt that the present market is too small to permit economical production by the method developed.

Jan 1, 1947

By Donald L. Mordell

Introduction A very large part of the world&apos;s fuel resources are in solid form, as various grades of ?coal, but an increasing proportion of fuel demands on this Continent and else-where are having to be met by liquid fuels. Convenience and, in many cases, cost weigh heavily in favour of the liquid: fuels, and there are many fuel burning applications where the use of coal would be impractical, such as for automotive or air transport. By extrapolating the present trends one might conclude that, in future years in Canada and the United States, coal will be used only in a few power stations close to coal fields. If such a state of affairs should arise, it will obviously prove embarrassing to those accustomed to make their livelihood from the winning and marketing of coal, but it is perhaps not so obvious that it must also prove an embarrassment to the nation. The major reasons for this are two in number. Firstly, if present coal production is to be replaced by oil production, a large capital expenditure is necessary, which must inevitably be paid by the consumer; and secondly, in times of emergency, large amounts of oil fuels are required for military purposes which cannot be achieved with solid fuels. It is obviously unwise, therefore, to discontinue the use of coal for those non-military jobs that it can do. If we examine the major fuel markets we find that there are three: Domestic heating Steam generation Transport by air, sea, and land For domestic heating, the extreme convenience of oil, in spite of its greater cost, has captured much of the coal market.

Jan 1, 1952

By Lin Li, Ahmad Ghahremaninezhad

"In this paper, the electrochemical behavior of ferric and ferrous couple on the pyrite surface was studied by application of the chronoamperometry technique in an acidic solution at room temperatures and atmospheric pressure. The effects of the pyrite origin, ferric and ferrous ions concentration on the electron transfer kinetics of Fe3+/Fe2+ reaction were probed. Tafel behavior of all the test conditions were developed. The results showed that the ferric-ferrous reaction on pyrite electrodes with different origins have a common mechanism, despite different reaction kinetics. The exchange current densities of the redox reaction have the same magnitude of about 10-5 A·cm-2, which is far lower than the value reported for the gold and platinum electrodes, but larger than that of the chalcopyrite electrode. The cathodic transfer coefficients are between 0.4 and 0.5, while the anodic transfer coefficients appear unusual with the lowest value being 0.23. It was also demonstrated that an increase of one order of magnitude of iron concentration has no clear effect on the exchange current density and cathodic transfer coefficients of Fe3+/Fe2+ redox reaction.INTRODUCTIONPyrite, FeS2, is mostly considered as a gangue mineral which frequently coexists with valuable minerals and metals, such as gold, copper and nickel. Its separation from valuable minerals can be a costly process (Chandra & Gerson, 2010). In refractory gold ores, the fine gold particles are locked inside the pyrite structure. Oxidative leaching of pyrite is a hydrometallurgical method to destroy the structure of pyrite and expose the fine gold particles to the cyanide solution in the downstream cyanidation circuit. Pyrite oxidative leaching can be achieved by oxidation of pyrite via oxygen and ferric ion(McKibben & Barnes, 1986). In fact, pyrite oxidation by oxygen and ferric is a significant source of acid mine drainage(AMD), which adversely causes serious environmental problems(V. P. Evangelou, 1995).The pyrite oxidation mechanism is accomplished in three consecutive steps: (i) pyrite is oxidized by oxygen and ferrous ion formation (Eq. 1); (ii) ferrous oxidation by oxygen and ferric ion formation (Eq. 2); (iii) pyrite oxidation by means of ferric ions (Eq. 3). Hence, both oxygen and ferric participate in the pyrite oxidation process (Moses & Herman, 1991):"

Jan 1, 2016

By J. Paraszczak

ABSTRACT Diesel-powered loaders are a pillar of modern underground metal mining. As these mines are getting deeper and hotter and the emission regulations stricter, ventilation costs are soaring, affecting production cost. Also, the cost of diesel fuel is expected to rise. These may make the use of diesel engines more problematic. Electric load-haul-dump machines (LHDs) are an interesting alternative. This paper compares features and performance of diesel and electric, cable-powered LHDs. It overviews equipment offerings, and compares, analyzes and discusses technical parameters, operational problems and cost issues. The paper gives some conclusions about electric LHD applicability and performance, indicates possible applications, and suggests further research work.

Jan 1, 2013

By H. L. Noblitt, Pauline Moyd, Louis Moyd

The deposit, which forms a ridge -adjacent to the York river, in Mont-eagle township, is held by Monteagle Minerals Limited, of Toronto. The ore is in a Precambrian gneiss which is composed of nepheline, scapolite, andesine and microcline feldspars, muscovite and biotite micas, and -corundum. The major orebody is tabular and is exposed for 1,200 feet along the crest of the ridge. It aver-ages about 90 feet in thickness, dips at about 70°, and was intersected by drilling at a vertical depth of 600 feet. The deposit was prospected for corundum in the early 1900's. Recent exploration was undertaken to deter-mine its potential as a source of high-alumina ceramic material, with by-product corundum and white mica. The program included prospecting, mapping, trenching, diamond drilling, bulk sampling, beneficiation research, a large-scale beneficiation test, product evaluation, market investigations, and plant design. Reserves, to a depth of about 300 feet, are estimated at about 3 million tons.

Jan 1, 1962

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By Jacek Paraszczak

For mining companies facing strong international competition and unfavorable commodities? prices, automation of underground operations has got a potential to increase productivity and help cut cost. However, despite considerable technological progress in this field, there still remain some problems to overcome. Furthermore, a success implementation of automation depends also on numerous operational, organizational and even human factors. In this context, this paper reviews briefly a technological progress with regard to different underground operations. Following that, several issues related to implementation of automated equipment and systems are presented and discussed. Particular emphasis is put on the factors whose importance is sometimes underestimated. Some recommendations in this respect are also given. It is stated that a success of an automation project is a function of many ?winning conditions?, which may be created through a very thorough planning and preparation. It is also underlined that despite achievements made, a vision of a man-less underground mine is not yet a question of near future as it may seem.

May 1, 2001

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

By M. Turner-Jones, N. Steenekamp

"The Lonmin Base Metal Refinery treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode as well as a concentrate containing the platinum group (PGM) metals. The original process employed a Sherritt design and utilizes atmospheric and pressure leaches for the dissolution of base metals. This paper describes the original flow sheet and the improvements made to enhance PGM recoveries, product quality and to increase capacity. Changes include the introduction of flash recycle cooling on the autoclave, batch leaches to improve the quality of the PGM concentrate and the implementation of solid-liquid separation with centrifuges. INTRODUCTIONThe Lonmin Base Metal Refinery (BMR) is about 100 km north-west of Johannesburg and treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode and a concentrate containing the PGMs. The plant was commissioned in 1985 based on a Sherritt design to treat 12 tonnes converter matte per day. The original flow sheet consists of a milling circuit, an atmospheric leach and a pressure leach to produce a PGM concentrate which is despatched by helicopter to the Lonmin Platinum refinery in Brakpan, about 40 km east of Johannesburg. The liquor from the atmospheric leach is treated by crystallization to produce a nickel sulphate hexa-hydrate crystal. The leach liquor from the pressure leach is treated by a selenium removal step followed by electro-winning to produce copper cathode. The spent solution from the copper electro-winning is recycled to both the atmospheric and pressure leach steps to provide sulphuric acid for the leaching reactions.Modifications were made to the original circuit to increase the plant capacity, to improve the PGM recoveries and to improve the quality of the PGM concentrate. Capacity increases included all the unit operations, new mill, new first stage, additional autoclaves, additional nickel sulphate crystallizers, new copper electro-winning and new batch leach reactors for upgrading the PGM concentrate. The current circuit is described in this paper and not the detailed history of each plant change."

Jan 1, 2012