Search Documents

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By Augustine O. Orumwense, Micheline Boisclair

"The use of stirred mill to complement tumbling mills in grinding fine grained minerals is increasingly becoming an attractive processing option. Parameters such as agitation speed, grinding media type and size, feed pulp density, and grinding time were studied in order to elucidate their impact on stirred milling. Test results showed that the parameters have a profound effect on stirred mill efficiency and operating cost. A comparative test with a tumbling ball mill was also made and the specific energies of both mills in fine grinding were analyzed. A difference of over 40% in energy savings particularly when the product size is smaller than 20 µm was obtained with the stirred mill.INTRODUCTIONIn industrial processes where very fine and ultrafine particles are required such as in chemical, ink, food, paint and lacquer, pulp and paper, plastics, pharmaceutical, metallurgical and ceramic industries, the use of stirred mills for grinding is well established. Mineral processing plants are gradually shifting focus to the use of stirred mills for fine grinding and /or regrinding purposes as the target liberation size gets very small. A number of plants processing finely/sparsely disseminated ores are known to have adopted stirred milling technology for their fine grinding needs (Enderle et al., 1997; Harbort et al., 1999; Gao et al., 2000; Davey, 2003 & 2006; Pease et al., 2006).There are different kinds/designs of stirred mills available on the market but, all can be divided into two sub groups namely fluidized and non-fluidized types. The non-fluidized stirred mills consist of Tower mill, Vertimill, Sala agitated mill (SAM), and ANI-Metprotech (SVM). These mills are characterized by their low-speed and the use of fairly coarse grinding media size, 3 – 20 mm. Hence, they are mostly suitable for relatively coarse grinding application. The fluidized type includes the Isamill, Netzsch mill and Stirred mill detritor (SMD). These mills have a characteristic high agitator speed, use fine grinding media size of 0.5 – 5 mm, and are employed in very fine grinding operations. The superior fine grinding capability of stirred mills is attributable to two main process parameters, which are the use of fine grinding media and a high mill speed."

Jan 1, 2008

By Renaud Adams, Vladimir Salatic

"The El Mochito Mine located in Honduras, Central America, has produced lead, zinc and silver in concentrates since the 1950s. The paper discusses changes made in both lead and zinc circuits to reduce costs while maintaining production during the recent period of low metal prices.The intent of this paper is to show that sometimes thinking “outside the box” is beneficial for progress. Also, in striving for better metallurgical results we should not forget the basics of flotation. Sometimes the latest trends may not be applicable to the ore we are treating and may not meet the operating cost constraints.A major beneficial impact on El Mochito metallurgy was achieved when the overall grind was coarsened, eliminating the significant percentage of slimes. Switching from two parallel twostage grinding circuits to one circuit with three-stage series grinding has resulted in a significant reduction in power and steel consumption. With minor layout/reagent modifications, both lead and zinc circuits gained not only in retention time but as well in producing better grade products.Of course, the challenges are still there; they exist and only with the full support of operational data collection and metallurgical laboratory investigation success can come. That is why, we as professionals, can never stop in trying to make the most of what we have.INTRODUCTIONThe El Mochito Mine is owned by American Pacific Honduras S.A. de C.V. (AMPAC) a subsidiary of Breakwater Resources Ltd. Of Toronto, Canada. The mine is located in western Honduras, approximately 220 kilometers northwest of the capital city, Tegucigalpa and 90 kilometers south of the country’s second largest city, San Pedro Sula. The mine began operating in 1948 and to date has produced more than 19 million tonnes grading 240 g/t Ag, 3.5% Pb and 7.4% Zn. Production in 2005 was 700,190 tonnes grading 87 g/t Ag, 1.85% Pb and 6.61% Zn.Decreasing metal content in the ore followed by the lowest zinc price on the market in the last 15 years (see Figure 1) has reduced the cash flow and endangered to stop the operation."

Jan 1, 2007

By C. Veloo

"Westmin Resources operates a mine/mill complex at Myra Falls and produces copper and zinc concentrates with minor associations of gold, silver, and lead from a polymetallic, massive sulphide orebody. Mill flotation performance has historically been plagued by periods of uncontrollably high circulating loads leading to low concentrate grades and below optimal tails. This led to a detailed examination of the flotation process. Locked cycle, and pilot plant data are presented. In addition, plant design and commissioning as well as column cell details are discussed. A comparison between actual and predicted performance is also presented. Benefits realized are higher copper and zinc concentrate grades and improved zinc recovery.PrologueMyra Falls Operations is located at the south end of Suttle Lake in Strathcona Provincial Park. Access to the mine site is provided by a 90km paved highway from Campbell River, British Columbia.The mine and facilities are nestled in the narrow Myra Valley between Mount Phillips and Mount Myra. These steep, rugged mountains rise from the valley floor at an elevation of 900 feet to summits of almost 6000 feet. The steep slopes are heavily wooded with fir, hemlock, and cedar up to an elevation of 4000 feet where a transition to alpine meadows occurs. The summits are craggy rock faces, some capped with glacial ice. Myra Creek winds its way through the valley dropping several hundred feet into Suttle Lake. Precipitation is high at over 100 inches per year, which may include up to 10 feet of snow in winter. The temperature may range from 32° C in summer to -18° C in winter.Myra Falls began production in 1965 with the Lynx Mine, supplemented by the Myra and Price Mines in subsequent years, feeding a 950 stpd mill up until the middle of 1985 when the H-W mine was brought into production. The original mill was replaced with a modern 2700 mtpd facility and in 1988 production was increased to 4000 mtpd.Both Lynx and H-W mines are currently in production producing an average of 3650 mtpd. The ore minerals are primarily sphalerite and chalcopyrite, with subordinate galena, bornite, tetrahedrite, and electrum."

Jan 1, 1992

By Jan W. Merks

"The settlements between mines and smelters are based on the mass of metal contained in concentrate lots. The mass of contained metal is a function of the wet mass of a lot, and its moisture content and metal grade while the variance of the mass of contained metal is a function of the same variables and their variances. Uncertainties in the measurement procedure applied to estimate each variable are quantified in terms of precision and bias. The absence of bias and an acceptable degree of precision are the keys to effective risk analysis and loss control.ISO Technical Committee 183-Copper, Lead and Zinc Sulfide Concentrates, has developed standard methods for sampling and weighing, estimating precision and testing for bias, the determination of mass loss on drying, the calculation of the mass of contained metal and its variance, and various analytical methods for major and minor metals. The variance for wet mass is calculated from the precision of the scale while the total variances of moisture and grade are estimated from pairs of interpenetrating primary samples. The variance of contained metal can be calculated either from mine data or from smelter data but the risk associated with the settlement is largely determined by the absence or presence of bias and the variance of differences between exchange assays.ISO/TC 183 does not deal with precision and bias for exchange assays but is developing guidelines to determine realistic splitting limits. Given that the exchange of assays between mines and smelters accounts for a large part of the risk associated with the settlement, precision and bias for exchange assays should be measured and monitored. The need for umpire services can be reduced by applying statistical quality control (SQC).Calibrating static scales, moisture balances and analytical balances, bias testing of sampling methods and sample preparation procedures, estimating the variance of a single variable or the variance of a function that a set of variables defines, and monitoring precision and bias for exchange assays, are the quintessence of metrology, the science of measurement, when applied in mining and metallurgy."

Jan 1, 1995

By Olli Haavisto, Juha Timperi

"Accurate on-line assays of mineral slurries are the basis for effective operation of flotation circuits. Typically the elemental content measurements are obtained by an X-ray fluorescence (XRF) analyzer, which samples the process lines and performs the analysis concurrently line-by-line. For a more frequent measurement of each slurry line the XRF measurements can be complemented with reflectance spectrum information. In reflectance spectroscopy the absorbance properties of the slurry in the visible and near-infrared wavelength range are analyzed. The advantage of reflectance spectroscopy is that measurements can be obtained quickly and simultaneously from several slurry lines. However, since the shape of the spectrum is only indirectly affected by the slurry elemental contents, frequent calibration of the measurement against the XRF analyzer is necessary. This study elaborates the combination of reflectance spectrum analysis with XRF. Results of laboratory tests for different slurries are presented and the operation of the system in a copper-zinc flotation plant is demonstrated.IntroductionElemental analysis of mineral flotation slurries is the most important factor in evaluating the performance of concentration processes. Timely on-line assays are also used as the basis for controlling the circuits and ensuring that the grade and recovery targets are reached. X-ray fluorescence (XRF) is the dominant technology in on-line elemental slurry analysis, and typically centralized XRF analyzers are used. The advantage of a centralized analyzer is that one measurement probe can be used to acquire the data from several slurry lines. This reduces the overall operating cost of the system when compared to distributed analyzer system design with several measurement probes requiring maintenance and spare parts. Slurry samplers are installed in the interesting process flows and representative sample flows are brought to the analyzer, where the slurry is further sampled and measured consecutively by the XRF analyzer. Due to the centralized structure of the analyzers and consecutively measurement of the sampling lines the sampling interval per slurry line can be relatively long. In larger concentration plants with several sampling lines a typical assay interval is in the range of 10-20 minutes."

Jan 1, 2016

By J. E. Nesset, J. A. Finch, Rosenblum. F., S. Somot

"In a previous presentation at the CMP, evidence was shown for the formation of hydrogen sulphide (H2S) in self-heating experiments on pyrrhotite-rich samples (Somot and Finch, 2006). Oxidation of H2S is strongly exothermic leading to the proposition that H2S is playing a key role in the self-heating process. Subsequently, tests in two weathering apparatus (I and II) were run under varying oxygen levels to further examine conditions leading to self-heating. To characterise their resulting self-heating capacity the samples from the weathering tests were subjected to a modified Stage B test using the self-heating apparatus developed by Rosenblum and co-workers (Rosenblum and Spira, 1995; Rosenblum et al., 2001). Results showed highest self-heating after weathering occurs under low oxygen conditions, supporting the H2S hypothesis. It was observed that highest heating rates are not directly related to highest weight gains of samples.INTRODUCTION“Sulphides” refer to several types of minerals containing sulphur in its lowest oxidation state of - 2. Self-heating is the spontaneous heating of a material without external heat input. It is well established that some sulphides will self-heat on exposure to moisture and oxygen (Farnsworth, 1977; Good, 1977; Rosenblum et al., 2001; Wu and Li, 2005). This process is highly exothermic and if the heat generated is not dissipated, combustion may occur when the temperature reaches the ignition point of the sulphide (typically 350-400 °C). The hazards of sulphide self-heating range from handling hot material, to sulphur dioxide release, to fires. The literature documents self-heating incidents underground, on ships and trucks transporting sulphide concentrates, and in mine waste (tailing) disposal areas (Stachulak, 1990; Lukaszewski, 1969; Headley et al., 1977). Lukaszewski (1969), Farnsworth (1977), and Good (1977) note that sulphide minerals can act as fuel to promote underground mine fires. Based on such findings, sulphide minerals could become classified as hazardous materials, making transport of concentrates and storage of mine waste subject to stricter and more costly regulation. The problem is one the industry is keen to avoid."

Jan 1, 2009

By Jan E. Nesset, Antonio DiFeo, James A. Finch, Jose Hernandez-Aguilar, Cesar O. Gomez

"The gas dispersion measurement sensors and methodology developed by the mineral processing group at McGill University have to-date been employed at a number of plants in Canada, Australia, the U.S., South Africa and South America. In some cases the measurements have been directly linked with metallurgical performance while in others the gas dispersion surveys on their own have proved very useful in understanding the behaviour of the flotation cells. In addition to reviewing the current state of the gas dispersion measurement technology, the paper will present a series of case studies from the various plants and will show how this technology brings a remarkable new level of understanding to flotation behaviour. The influence of the bubble size distribution on recovery and grade are emphasized in the paper.INTRODUCTIONBackgroundThe advent of new sensors to characterize gas dispersion parameters in flotation cells is a development that is long overdue. While the chemistry of flotation has been studied since the early 1900’s, it is only now that the significance of bubble size distribution, gas rate and gas holdup can be meaningfully measured in-plant with robust and precise sensors. Early researchers, like T.A. Rickard (1916) recognized the importance of understanding the role of air and bubbles in flotation when he wrote in 1916 “we know that the key to the flotation process is to be found not in the oil, the acid, or the apparatus, but in the bubbles. The man who understands the mystery of a soap bubble has mastered the chief mystery of flotation”. In his 1999 review paper on The Froth Flotation Century D.W. Fuerstenau laments the fact that due to their “inert nature”, bubbles have never received their due attention from researchers who tended to focus on the chemical, physical, surface and colloidal aspects, rather than the physics of the process. It is perhaps fitting that now, 100 years after the inception of industrial flotation practice at Broken Hill, Australia, researchers and industry have turned their attention toward the importance of truly understanding the role of bubbles in flotation."

Jan 1, 2005

By S. Banisi, M Nesari, J. A. Finch, N. Nobari, H. Javani

"The flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. Mechanical flotation cells are used in all stages. To investigate the amenability of flotation columns in the plant especially for cleaning and recleaning stages, a column was designed, constructed, and installed at the Sarcheshmeh pilot plant. The pilot plant, which has an identical circuit configuration compared to the plant, can process up to 2 t/h of ore. The overall rate constant of the ore along with the target recovery of 94% were used to size the column. A 26 cm by 550 cm column with two filter cloth spargers and a submerged froth washing system using perforated tubes was constructed. To detect the interface level a 180 cm conductivity probe consisting of 1.5 cm diameter ring electrodes was installed. The tailings flowrate controlled by a variable speed pump was used as the main control variable. The initial testing program revealed that the optimum superficial gas and wash water flowrate were 1.5 and 0.3 cds, respectively. It was observed that the cleaning stage grade when using the column could increase by 2-3% at constant overall copper recovery.IntroductionThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tomes averaging 0.90 % copper and 0.03 % molybdenum. It is in located south-east Iran and has been processing 40,000 t/d of ore since 1982. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcopyrite and chalcocite) is obtained after cleaning and re-cleaning stages in mechanical cells. Total recovery of the plant varies between 83-87 % depending on ore type and operating conditions."

Jan 1, 2000

By Ilpo O. Auranen

Background: Mines of today are moving ever increasing tonnages of rock. The new ore bodies tend be of lower grade and located deeper in the earth?s crust. The industry?s focus to overcome this ?deeper but poorer? ore problem has traditionally been to lower the costs by increasing the scale of mining. This has resulted in an ever increasing size of mining equipment like drills, loading shovels, dump trucks. The main focus has been in reducing the cost per ton of mining. This cost focus has often resulted in increased waste rock dilution and more ore losses. From costs to value: Waste rock dilution means waste rock in the concentrator feed. It?s value in open pit mining is equal to the value of ore it replaces. In underground mining, waste rock dilution?s value is equal to the value of ore it replaces added to the costs of mining it. It is commonly accepted that waste rock dilution in open pit mining ranges between 5 and 20% and in underground mining between 5 and 40 % . In a typical large open pit mine ore value is from 20 to 60 USD per ton and mining costs are 1 to 3 USD per ton. One percentage point reduction in waste rock dilution represents savings corresponding to about 20% of total mining operation costs. The difficulty of reducing waste rock dilution comes from the complicated nature of the ores. Accurate ore waste-border detection has not been possible due to excessive costs. Core drilling combined with geochemical lab analysis is the most accurate method for locating ore waste borders. However, it is also expensive and time consuming, which is why it is often combined with somewhat lower cost methods like sampling drill cuttings from blasting drill holes or from reverse circulation drills and analyzing them in a laboratory. The main drawback with these methods, in addition high costs, lies in the sampling accuracy and in the quality control of the whole process when a large number of samples have to be handled manually. In every mine it is possible to halve waste rock dilution by using new on-line analysis technology .

Oct 1, 2009

By Graham Holmes, John Starkey

"The Kinross Kubaka Project is a gold mine located in the Russian Far East. The grinding circuit, comprised of a 6.1 m diameter x 2.74 m long SAG mill and a 4.1 m diameter x 5.5 m long secondary ball mill in closed circuit with cyclones, was built using SAG Power Index and Bond Ball Mill Work Index testing to determine the grinding energy requirements. Extremely cold climatic conditions and the need to keep heated space and capital costs to a minimum, dictated a grinding circuit with no in-circuit crusher and no conveyors external to the mill. High energy requirements for both the SAG mill and the ball mill were correctly predicted and have allowed grinding production tonnage forecasts to be met. Design test data and production results are given.INTRODUCTIONIn 1995 Davy International Canada, now Kvaerner Metals E & C, was commissioned as the Engineer and Project Manager for the Omolon Gold Mining Company, to design and construct a gold extraction plant for the Kubaka gold deposit, located in the Russian Far East. This deposit had been studied extensively in Russia during the exploration phase and a Feasibility Study was completed in 1993 by Kilborn who visited the site twice during that year to inspect facilities and to take metallurgical test samples. More samples were taken in 1995 to check ore hardness variability, as part of the final design program by Davy.The client’s objective in designing the Kubaka grinding circuit was to achieve design tonnage at all times, even when milling the hardest ore zones in the deposit. Since the samples taken in 1993 were taken as composite samples, it was necessary to take additional samples in 1995 to determine the extent of the variability. Six samples were sent to Canada for SAG Power Index (SPI) testing. Five of these were combined as a composite open pit sample, while the sixth sample was taken from the site adits as a composite sample to represent undergound ore. These two composite samples were tested to determine the MacPherson Autogenous Work Index for comparison with the SPI values."

Jan 1, 2001

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014

By Barun Gorain, Andy Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimisation of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimisation, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterise cell hydrodynamics, gas dispersion properties, fioth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimisation of the Red Dog flotation circuit.INTRODUCTIONThe traditional methodology for flotation scale-up and plant design is based on the rule-of-thumb with safety factors, dimensionless hydrodynamic group similitude considerations, etc. With the recent trend towards larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-of-thumb and trial-and-error, then the probability of failure would increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimisation of the circuit to meet its metallurgical target. This results in a plant design incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2002

By G. Lipsett, S. Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by allowing assets to be used more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the “productivity paradox,” where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the benefits are in how effectively IT is used. Most business sectors have accepted that re-engineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors, but unique operational processes. The lessons of changing business practice in more common business processes, such as inventory control and customer-supplier relationships, can be adequately transposed into a mine setting. The unique operational processes in mines, in turn, require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manager training simulators. This paper reviews some of the latest IT products and outlines the processes and kinds of change that will be required in order to benefit from these new investment options.

Jan 1, 2009

By K. K. Murray, D. G. Gelderland

"The pressure oxidation autoclave at the Goldcorp’s Red Lake Gold Mines (RLGM) was commissioned in 1991. Since commissioning, the circuit has been well maintained and its capacity increased to mechanical and gaseous oxygen limitations. With advances in available technology, opportunities to produce more sulphide concentrate and a changing business environment, an optimization project has been initiated at RLGM. A multi-phase approach has been developed to optimize both the operations and economics of the circuit. This paper describes the history and future of the autoclave circuit at RLGM.AcknowledmentsWe would like to thank the operations and maintenance staff at Red Lake Gold Mines for their support and openness of mind to enact changes to enhance the operation. We would also like to acknowledge the members of the integrated team from Red Lake maintence, metallurgy, operations and corporate technical services that did the hard work to push past the status quo in order to advance productivity.OpportunityThe Red Lake Gold Mines (RLGM) pressure oxidation (POx) circuit has been in operation for over 25 years processing the high sulphide content gold bearing minerals. Increased sulphide concentrate production from improved flotation recovery and increasing gold sulphide association at depth has led to the POx circuit becoming a throughput bottleneck. The opportunity exists to process increased tonnages of sulphide concentrates and increase gold production. In order to realize this value, it will be necessary to increase the throughput capacity of the POx circuit.BackgroundThe POx autoclave at the RLGM, commissioned in 1991, was Canada’s first gold autoclave. It was installed to replace the two-stage fluid bed roaster that was built when the Campbell mine and mill were constructed in the late Forties. The circuit was originally designed to process 12.5 t/d sulphide sulphur in about 50 t/d of Campbell flotation concentrate. Following the merger of the Campbell and Red Lake Mines in 2006, the POx circuit started processing flotation concentrate from both Campbell and Red Lake Mills. In recent years, the circuit has been processing about 18 t/d sulphide sulphur in 75-85 t/d flotation concentrate."

Jan 1, 2017

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By Tim Hughes, Steve Gannon, Jennifer Abols

"In the past year, two very innovative gold ore processing plants have been designed, built and commissioned by Gekko Systems Pty Ltd. The first plant in Vietnam utilizes conventional crushing and ball milling followed by gravity concentration (Inline Pressure Jig (IPJ) and Falcon concentrator), flotation, intensive leaching (GFIL), the first industrial scale use of AuRIX®1001 ion exchange resin and a cyanide destruction circuit. The second plant, in Australia, uses a 3 stage crushing circuit to crush the gold ore to minus 1mm, followed by gravity concentration utilising a rougher, scavenger, cleaner circuit of IPJ’s and a Falcon concentrator. A direct smeltable gold concentrate is produced as well as a lower grade concentrate for future intensive leaching or sale. Both plants were designed and built within very tight time frames and budgetary constraints. The experience gained during the plants’ design, commissioning and operation are discussed.INTRODUCTIONGekko Systems (Gekko) is a leader in the development of innovative technology for gravity recovery and intensive cyanidation. It provides low cost and metallurgically optimal solutions for its customers. It has also led the trend away from whole ore cyanidation (CIP/CIL) towards gravity/intensive cyanidation (GIL) and gravity/flotation/intensive cyanidation (GFIL) plants. These types of plants offer low capital costs, low environmental impact and maximum return to investors (Rob J Longley et al, 2002). Key to this type of flowsheet is the application of a continuous concentrate unit, such as the InLine Pressure Jig (IPJ), which is designed to produce high gold gravity recoveries at a coarse grind (Sandy Gray, 2003). When combined with other gravity devices, and/or flotation, and intensive cyanidation, using the Gekko InLine Leach Reactor (ILR), very high overall recoveries can be achieved.In 2004, Gekko launched a new range of products called Gekko Modular Systems. The idea was to provide off the shelf, complete solutions for the separation and recovery of complex and free gold as well as the pre-concentration of diamonds. A series of modules were designed that incorporated Gekko manufactured as well as outsourced equipment. Gekko now offers modules ranging from feeding and conveying to crushing, gravity recovery, flotation, intensive cyanidation, refining and detox (see Figure 1)."

Jan 1, 2007

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003