Search Documents

By J. Eric Nylund

"Intensive mechanization and automation in the LKAB, Kiruna Mine in Sweden have resulted in substantial rise in productivity and decrease in production cost. Capital investment in a modern mine today averages a considerable amount per miner and costs increase with requirements for more efficient methods and equipment. Equipment reliability becomes more and more important. Equipment maintenance requirements are directly proportional to equipment reliability and grade of availability. Weaknesses in the equipment result in unnecessary costs with regard to maintenance which can add up considerably per year, but of more importance are the costs caused by equipment breakdown. These breakdowns disturb or interrupt the production and often cause damage to other parts of the system. This paper discusses the important parameters involved in mine car wheel wear and the design principles of wheels, axle suspension and track.IntroductionTrains operating in an underground mine do not follow the same standard of performance as trains operating on surface railways. The differences in speed, curve radius and environment require different methods of calculation for underground train systems, and when judging the parameters involved one must keep in mind these differences at all times.While surface railway technology was given all possible attention over the last century no one was seriously looking into underground rail haulage in the sense of rail vehicles performance on the track until LKAB in 1975 started to question the methods of calculations used. Even though LKAB by then attained mine car maintenance cost that was 1/6 to 1/10 of other mining companies they were not pleased with the situation. The objective for the ensuing engineering work was to derive the reasons for wear and breakdowns. Once those reasons were established, the design of a completely new generation of mine cars could start. The result of these efforts were beyond all expectations. The maintenance cost on mine cars had been reduced to 1/15 of prior car generation which already had comparatively low cost.The most significant cost savings were made on wheel maintenance, which earlier represented 50% to 55% of car maintenance. Wheel life was increased from an average of 3 to 30 years or more.The LKAB theories around wheel wear are described in the following report."

Jan 1, 1987

By Y. L. Su, S. Vongpaisal, H. A. Smith

"It is extremely difficult for a mine's central control room operator to control peakpower demands and to maintain normal materials handling operations at the same time. An investigation of the Falconbridge Strathcona Mine 's central control room has revealed that there are more than eight thousand possible combinations of ""situations"" that can arise. For such a circumstance, an expert system can become a very valuable tool to assist the operator in taking the most appropriate and timely action.A forward chaining expert system module has been developed for this application. The module is based on Level 5 ObjectTM software. It is graphics oriented and user-friendly. Training requirement is minimal.ForewordThis paper has arisen out of work carried out by YLS Associates and Falconbridge Limited as part of a contract between Falconbridge and the Department of Energy, Mines and Resources, Government of Canada, on the application of expert systems in mining operations.IntroductionThe electrical bill charged to large consumers by Ontario Hydro is based upon two elements: demand and energy consumption. The demand is the peak kilowatt level that the consumer has required during a monthly period. It is not uncommon for the demand portion to be as much as one third of the monthly bill. Energy consumption is the total kilowatt-hour s (kWh) consumed during the period.Ways to reduce the energy consumption part of the electrical bill involve utilizing energy-efficient equipment and operating machines in off-peak hours when a lower energy rate is charged. Maintaining the peak power below a critical level may require that simultaneous usage of major pieces of equipment be avoided. A 3000 kW skip run at an inopportune time could cost a company an extra $30,000 in that month's power cost.Potential disadvantages associated with peak power control are lost production due to work stoppage and increased operating costs due to the need to employ extra personnel. Most companies find these matters relatively easy to deal with and with incentives provided by Ontario Hydro, actively pursue this facet of energy savings (Harju , 1991)."

Jan 1, 1993

By K. Najim, D. Hodouin

"The raw ores which are processed in mineral processing plants exhibit very strong variations of their physical and chemical properties. As a consequence, the performances of the comminution and separation processes vary greatly from time to time. Model-based control strategies improve the performance of the plant; however, they require some form of adaptation to cope with the variations of the are properties.This paper deals with the use of adaptive techniques for the control of mineral processes. It begins with a survey on adaptive control algorithms including parameters estimation aspects. Then several examples dealing with crushing, rod, ball, autogenous and semi-autogenous grinding, flotation , drying and calcination processes are reviewed.IntroductionThe operation of the various processes of mineral processing plants (crushing, grinding, flotation, dewatering, etc.) is generally controlled using empirically tuned regulators of constant structure, such as PID controllers. To improve the operation performance, mineral processors try to implement specifically designed controllers, i.e. controllers based on plant dynamic models. Most of the time, these techniques improve the control of the mineral processing installations. However, modelling is a complex procedure because of the problems of measurement and data management, specific to this industry, and because of the variations of the model parameters. In this context model-based control strategies do not always bring the expected improvements or are sometimes discarded and replaced by more conventional techniques .The sources of variation of the dynamic behaviour of mineral processing systems can be classified into three categories: (I) the inherent changes of the raw ore properties (composition, grindability, mineralogical texture, etc.); (2) the process tuning modifications (grinding media loads, number of hydrocyclones, slurry level in flotation cells, agitation speeds, etc.); (3) the feedrate variation of the ore, water, chemical reagents, etc. All these factors change the fundamental properties of the process dynamics such as the grinding or flotation rates and the residence time in the equipment. The simplified linear models which are used to describe the process dynamics are not able to track the complex behaviour of the mineral processing systems when the amplitude of the sources of variation are too large. The mismatch between the model and the plant behaviour is then frequently a cause of model-based controller failures."

Jan 1, 1992

By Frederick W. Breaks, Andrew G. Tindle, Julie B. Selway

"Abstract - Rare-element pegmatites may host several economic commodities, such as tantalum (Taoxide minerals), tin (cassiterite), lithium (ceramic-grade spodumene and petalite), and cesium (pollucite). Key geological features that are common to pegmatites in the Superior province of Ontario and Manitoba, Canada, and in other large tantalum deposits worldwide, can be used in exploration.An exploration project for rare-element pegmatites should begin with an examination of a regional geology map. Rare-element pegmatites occur along large regional-scale faults in greenschist and amphibolite facies metamorphic terranes. They are typically hosted by mafic metavolcanic or metasedimentary rocks, and are located near peraluminous granite plutons (A/CNK > 1.0). Once a peraluminous granite pluton has been identified, then the next step is to determine if the pluton is barren or fertile. Fertile granites have elevated rare element contents, Mg/Li ratio < 10, and Nb/Ta ratio < 8. They commonly contain blocky K-feldspar and green muscovite. Key fractionation indicators can be plotted on a map of the fertile granite pluton to determine the fractionation direction: presence of tourmaline, beryl, and ferrocolumbite; Mn content in garnet; Rb content in bulk K-feldspar; and Mg/Li and Nb/Ta ratios in bulk granite samples. Pegmatite dikes with the most economic potential for Li-Cs-Ta deposits occur the greatest distance (up to 10 km) from the parent granite.Metasomatized host rocks are an indication of a nearby rare-element pegmatite. Metasomatic aureoles can be identified by their geochemistry: elevated Li, Rb, Cs, B, and F contents; and by their mineralogy: presence of tourmaline, (Rb, Cs)-enriched biotite, holmquistite, muscovite, and rarely garnet.Once a pegmatite dike has been located, the next step is to assess its potential to contain Ta mineralization. Pegmatites with the highest degree of fractionation (and thus the most economic potential for Li-Cs-Ta) contain blocky K-feldspar with >3,000 ppm Rb, K/Rb < 30, and >100 ppm Cs; and coarsegrained green muscovite with >2,000 ppm Li, >10,000 ppm Rb, >500 ppm Cs, and >65 ppm Ta. Pegmatites with Ta mineralization usually contain Li-rich minerals (e.g., spodumene, petalite, lepidolite, elbaite, amblygonite, and lithiophilite) and may contain Cs-rich minerals (e.g., pollucite, Cs-rich beryl). The ore minerals of Ta are commonly manganotantalite, manganocolumbite, wodginite, and microlite; Ta-rich cassiterite is also commonly present. Tantalum mineralization tends to occur in albitic aplite, mica-rich (lepidolite, cleavelandite ± lepidolite), and spodumene/petalite pegmatite zones."

Jan 1, 2005

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By M. K. Mishra, U. M. R. Karanam

Relative to slender pillars, larger size pillars exhibit improved strata control. Fly ash, though traditionally treated as a waste product, is emerging as an alternate engineering material. This paper deals with the development of a strong fly ash composite material with additives. The geotechnical properties of this fly ash composite were determined and used to trap model core pillars, which resemble squat pillars. The trapped samples were tested under uni-axial loading in the laboratory and the results showed higher load-bearing capacity of the model core pillars. The reinforced fly ash composites provide lateral confinement and exhibit improved post- failure behaviour of the model cores.

Jan 1, 2008

By D. McConchie

The use of Bauxsol? (physically and chemically modified alumina refinery residues) to treat acid rock drainage (ARD), and sulphidic waste rock and tailings, provides new options for managing some intractable environmental problems at both derelict and active mine sites. Treatment of ARD waters using the Bauxsol technology shows that the effectiveness of raw Bauxsol material can be enhanced by including modest amounts of selected industrial minerals or common chemical additives. The type and amount of additive required and the amount of the blend needed to treat the water depends on the initial composition of the water and the target water quality; for some ARD waters, optimum treatment may require one or more changes in the type or amount of additive used. Maximum treatment efficiency can be achieved only when a balance is maintained between the rate of trace metal binding and the rate of change in water pH; adding treatment reagents faster than can be accommodated by the reaction kinetics will not result in more rapid water treatment. This paper presents the results for treating several ARD waters to illustrate the importance of blend selection and treatment procedure. Although treating ARD water is often necessary, this strategy treats the symptoms rather than the cause. The best permanent solution is to treat the sulphidic waste rock or tailings such that they do not continue to oxidise and produce acidic metal-rich leachates; sulphide oxidation needs to be stopped or slowed to a rate that can be accommodated by normal environmental processes. Capping lined impoundments is not a solution because all caps and linings will inevitably fail some time in the future creating a nasty surprise for some future generation. Adding lime is also less than ideal because the lime leaches from the treated material; treatment often appears to be effective for a few years and then fails. Bauxsol technology offers effective alternatives to conventional liming and capping procedures and Bauxsol blend application rates and procedures can be planned to ensure that no acidic or metal-rich water can ever escape from the site. Bauxsol can be physically mixed with the sulphidic mine wastes or it can used to form subsurface permeable reactive barriers, or both. Bauxsol treated waste rock and tailings can be immediately and effectively revegetated. In this paper we present leachate quality and plant growth rate data for several sulphidic waste rock and tailings deposits treated using the new technology.

May 1, 2003

By Richard Morland

The Ekati Safety Guarantee is a conversation that has been taking place at Ekati for the last two years. It is a challenging, confronting, inspiring conversation which encourages people to see and pursue the possibility of guaranteeing that nobody who works at Ekati will be seriously injured or killed at work. The conversation takes us out of the normal, incremental approach to safety improvement; it takes us out of the world of striving, of seeking, of trying, and allows us to stand in, and be a stand for the future possibility of Zero Harm. It requires an unreasonable stand for, and commitment to, our own safety and the safety of our colleagues. A Powerful Conversation The safety guarantee began with conversations between executive team members and has been propagated regularly through the line through management meetings, pre-shift meetings, during workplace inspections, job safety observations, job and project planning, orientation and induction sessions, and when opportunities present themselves. This is a conversation that continues outside of Ekati with family, with government, with community members. It is a stand for safety as a value. The conversation about the safety guarantee is now pervasive at Ekati and forms part of a framework of initiatives that have led to sustained improvement in safety performance. During the last two years, the recordable injury frequency at Ekati has dropped to its lowest level in Ekati?s history. At the same time, job safety observations have increased from 500 per month to 4000 per month, whilst the overall number of people at Ekati has reduced by 30%. It has led to new ways of thinking about the conduct of operations. It influenced the 2008 upgrade of the Ekati process plant, resulting in the development and implementation of a crane lift protocol that eliminated injuries during over 100 lifts in two weeks, in an area of difficult geometry and with multiple entrances. It created space to successfully conduct a challenging commissioning period for the process plant crusher, during which time the machine was disassembled and reassembled several times, without incident or injury. No production pressure was permitted to interfere with this work, in line with our stated aim that we wanted everyone involved to guarantee that they would not be seriously injured or killed?our people had the space to do the work at a pace, and in a way, that guaranteed this outcome.

May 1, 2010

By M. Carvalho

The primary motivation underlying the proposal of polygeneration systems for mine sites is to increase the efficient use of natural resources by combining different technologies and energy resources while satisfying energy service demands. For many mineral producers, particularly in Canada?s mining extremes of climate and depth, energy in support of mineral production can be the second largest cost centre after labour. A generic methodology is proposed for the design of energy supply systems in mine sites, based on a search for the minimum discounted cost of energy supplied for all feasible different plant configurations. These configurations can be represented within a connectivity matrix which corresponds to a network representation. A Mixed Integer Programming formulation is set out for the multiperiod synthesis and operational planning problem. This is characterized by i) binary variables for the selection of technologies, ii) integer variables for the determination of the number of units installed, and iii) by continuous variables for the representation of energy and economic flows. Through the integration of particular energy supply strategies matching specific mine circumstances (on-grid, remote, degree days, etc) and consideration of technologies that improve energy efficiency, hitherto not considered new technologies and demand management systems or new perspectives on optimal mine site energy supply can be investigated. Some of these investigations identify the economic conditions through which biomass energy feedstocks should be used, for direct heat production, for gasification and providing for Fischer-Tropsch syndiesel manufacture. As well as integrating demand from mobile diesel-fuelled plant into an optimization procedure that hitherto has only been considered for static energy production and consumption plant, this analysis shows how the techniques can be used to explore economic conditions of threshold prices for biomass (purpose-grown biomass and peat are considered herein) and trucked-in diesel. The methodology also allows for electricity and syngas storage and diesel and biomass bunkering. Within the paper the energy demands for a remote, open pit mining operation located in Northern Ontario are considered as a case study to illustrate the technique and investigations. As expected, for mines close to electricity, natural gas, and diesel distribution infrastructures, the optimal choice is to connect. When a constraint is applied specifying that connection is not possible, as would be for the case exemplified, the optimal choice includes some of the more exotic options for mine site energy supply.

Aug 1, 2013

By Scott D. Long

"Abstract-Grass roots exploration has an emphasis on good precision at low (sub-economic) concentrations of an element, in order to identify "anomalies" which may lead to drilling targets. Although it is wise to have well-defined quality controls in place during early stage sampling, the control procedures at this stage tend to be rudimentary. When a deposit warrants detailed delineation, the need for accurate geological characterization and assaying of ore-grade rock must be supported by appropriate quality control procedures.As a project returns more promising results, and the likelihood of the project warranting a prefeasibility study increases, it is time to tighten quality assurance requirements and quality control protocols. Delays in instituting adequate quality control and verification procedures may lead to costly remedial actions that can also delay completion of the prefeasibility or feasibility study. Sometimes, as a project matures, the quality control and quality assurance aspects fail to keep pace with the changing nature of the work: an increasing emphasis on precise and accurate assaying of oregrade rock.A resource model is like a house of cards. The foundation of the house is the geological observations, the sampling methods and the geological interpretations performed upon those samples. Upon the sampling, which includes all the sub-sampling steps of sample preparation, rest the assay results. The quality of the assays can be no better than the quality of the sampling. Good assaying technique will preserve all biases and imprecisions introduced during sampling and sample preparation; it cannot remove them. If the sub-samples and/or assays are bad and must be redone, all the succeeding levels of the house of cards must also be rebuilt, or at least patched up.From geological observations, a geological interpretation is built, the quality of which is critical to the construction of an acceptable resource model. Geological elements are difficult to assess, and are not discussed here; they are dependent upon the expertise of the geologists involved. Geological knowledge contributes essential quality control elements to resource/reserve determinations (Sinclair and Postolski, 1999; Postolski and Sinclair, 1999).This paper consists of five sections: (1) overview of quality control protocols, (2) maintaining quality control of databases, (3) quality control of drill sampling, (4) optimizing crushing and grinding requirements, and (5) quality control of assay data acquisition."

Jan 1, 1998

By Pierre Gaucher

It is possible to selectively mine an orebody by combining the use of the SSW probe with any bulk mining methods as well as narrow vein exploitations. In other words, thanks to the use of the SSW probe, mining operators will be able to reduce and control dilution that is generally associated to every mining operation. Already, quick and substantial savings have been obtained. Falconbridge mines have demonstrated in Sudbury and Raglan operations, that the SSW probe can log nickel, copper and iron sulphides in blast holes. They have raised the grade and reduced dilution by outlining the limits of the ore zones before selectively loading explosives in the blast holes. By lowering the probe in a blast hole, a profile of the ore content is instantly measured and recorded. Logging cored diamond drill holes at the mine have demonstrated that the ore content (nickel, copper, cobalt, PGM) as assayed is proportional to the intensity of the probe?s electromagnetic response (EM), probably because the nickel / pyrrhotite ratio is uniform within a given orebody. The probe also measures the intrinsic conductivity of the sulphides and the percentage of magnetite. All probe readings are displayed and automatically stored at a 10-cm interval within the same reading unit. A 30-meter blast hole takes less than 2 minutes to survey. The whole instrument is light (12 kg) and very simple to use. One operator can carry the SSW system and survey either down or up-holes. The probe works from ?40°C to +50°C. Plotting the measurements of the SSW probe in blast holes (2-3-4-6-10 inches in diameter) before blasting allows to determine the exact shape of the orebody within the waste rock and uneconomic low-grade ore. Thus, only the portion of the holes that contains ore is blasted. The dilution is then much reduced and, by leaving the waste and low-grade ore in place, the mine saves on transportation, blasting, crushing, backfilling, milling, etc. Thousands of dollars are thus saved. Some savings may also be achieved during the development of stopes by guiding development drifts and by replacing diamond drilling by percussion drilling. In some circumstances, when the probe shows that some of the rich ore was not drilled-off, additional blast holes will allow to recover pockets of rich ore that otherwise would have been abandoned in the walls of a stope.

May 1, 2001

By Louise Corriveau

Exploration strategies have traditionally considered felsic gneiss complexes of the Canadian Shield sterile. This paradigm is challenged with the discovery of extensive granulite-facies Cu-Au, Fe oxides-bearing hydrothermal systems in the 1.4 Ga Bondy and 1.5 Ga La Romaine volcano-plutonic complexes of the Grenville Province. Early identification of magnetite-rich units in association with meta-exhalite and pelite-like units was key to targeting the search for mineralization, protolith information and indicators of pre-metamorphic hydrothermal activity during regional surveys of these frontier terrains. Textural evidences for a volcano-plutonic setting were found. There remained, however, numerous impediments to the recognition that the ubiquitous magnetite-laden units and associated aluminous gneiss were hydrothermal in origin. Many metamorphic reactions form magnetite at the amphibolite to granulite facies transition, and hydrothermally-leached rocks resemble metapelite or migmatitic restite, while carbonate alteration zones may look like marble or calc-silicate rock. Non-typical metamorphic mineral assemblages, modes and colours arise when hydrothermally-derived rock types are metamorphosed. These effective markers served as tools for reliable field identification of hydrothermally-altered rocks. In our case-studies, we traced pre-metamorphic hydrothermally-driven Fe-oxide precipitation in association with sericitization, albitization, pyrophyllite alteration, chloritization, and B enrichment by mapping unusually high contents of (1) magnetite or hematite, (2) biotite, (3) albite, (4) sillimanite, (5) orthopyroxene or phlogopite with cordierite, and (6) tourmaline or kornerupine. The unveiled garnetite, tourmalinite, and aluminous gneiss had assemblages that vary according to metamorphic grade and composition. To assess if high mode of Fe-Mg-Al phases resulted from partial melting (restitic residue) or metamorphism of hydrothermal rocks, we compared leucosome mineral assemblages, shape and amount with that expected of in situ partial melting reactions. In both areas there is no compelling evidence for these units to be restites. In contrast, the presence of lapilli in garnet-cordierite-sillimanite gneiss, though extremely rare, constitutes conclusive evidence for extreme pre-metamorphic high-sulphidation alteration of a volcanic protolith, while Fe-oxides or sillimanite-bearing nodules and veins record a less pervasive alteration. Geochemical research on element mobility and mass balance calculations further testified of an hydrothermal origin for these gneisses. The magnetite-rich units, together with calc-silicate rocks, garnetite, hornblendite, albitite among amphibolite, provided effective guides to sites of fluid discharge and led to the discovery of Cu and Cu-Au showings. With the presence of highsulphidation alteration, these features suggest early Cu-Au VHMS-type alteration halos within a predominantly felsic composite volcano-plutonic arc setting for both case-studies. Evidences for subsequent F-driven orthomagmatic fluid activity are also present.

May 1, 2003

By M. Amsden

"Since the computer program is far from complete this must be only a brief progress report on the computerization of flotation metallurgy at the Ecstall concentrator at Timmins.Ecstall is currently treating about 10,000 tons per day of two different ore types. One is a low sulphide copper-zinc ore, the other is a high sulphide lead-zinc-silver ore. The concentrator is divided into three individual grinding and flotation circuits. In effect there are three mills under one roof. Normally there are two circuits on copper-zinc ore and oneone lead-zinc-silver ore. At this point in time one of the copper-zinc circuits is under computerized metallurgy control.The first step in this control is the use of an ARL on-stream x-ray analyzer, coupled with a Honeywell 21 computer which types out assays and recoveries for each individual circuit. Our approach to a computer program was to keep it simple. The program was written to coincide as closely as possible to what an operator would do in the performance of his duties based on the in-formation he was getting from the x-ray analyser read-out. Initially, computer control was put on just the copper circuit of the ""A"" Division, controlling the collector addition at three points in the circuit; primary, secondary, and scavengers. The control was based on recoveries and the grade of the copper concentrate. Targets like 95% recovery and 24% copper concentrate grades that it was felt the circuit could achieve were set to start with. It quickly became apparent that this alone was not enough because if on a certain ore the best recovery that could be made was only 94.9% the computer kept calling for more reagents until the circuit was completely out of control. On another ore it might have been quite possible to get 96% recovery but when the set point of 95% was reached the computer stopped trying for any more. To overcome this problem a very simple optimum seeking program was devised by one of the Ecstall staff and it has worked very satisfactorily since being put into use in July 1970.In the copper float only the two collectors R-208 and the xanthate R-317 are under computer control. The addition of frother and depressant is left to the operator. The flotation cells have automatic level controls which can be adjusted by the operator. pH is controlled automatically through a lime loop-sensor arrangement."

Jan 1, 1971

By Ted Nuorivaara

The use of polymer-surfactant mixtures as foam stabilization agents is a topic that has drawn the attention of several fields but has so far not be thoroughly studied in the context of mineral froth flotation. The present work showcases a study on the impact on flotation performance of cellulose surfactant derivatives and their mixtures with commercial frothers. Bubble size and foam property measurements were run in a two-phase system along with laboratory-scale flotation experiments conducted using a porphyry copper ore from a mine in Finland. A comparative analysis on recovery, grade and flotation kinetics is presented on the products obtained using: i) a partially hydroxylated cellulose derivative (i.e. hydroxypropyl methyl cellulose; HPMC), ii) a commercial polyglycol-ester frother (Nasfroth240; NF240), and iii) mixtures of these two. The results show that using frothers with a total concentration of 30 ppm, the HPMC-NF240 mixtures provide advantages in terms of Cu recovery, (i.e., up to 95%), compared to the use of either NF240 (ca. 76%) or HPMC alone (ca. 1%). Interestingly, only a small proportion of HPMC mixed with NF240 was sufficient to produce a measurable increase in recovery. This improved performance was attributed to a synergistic effect of the polymer-surfactant mixture which further reduced the bubble sizes in a two-phase system compared to that of NF240. The present work offers a further step into understanding the phenomena taking place when a short chained surfactant is either substituted or mixed with a cellulose derivative, offering potential ways of exploiting this behavior for the enrichment of minerals. INTRODUCTION Froth flotation has been the predominant technology used to beneficiate sulfidic copper minerals such as chalcopyrite ever since it was invented in the late 19th century. The reason for the domination of flotation technology lies behind its versatility in selective separation as well as relatively cheap operational costs (Wills & Finch 2015). Even though flotation of sulfidic copper minerals is moderately well understood based on the broad research work done around the subject (e.g., Albijanic et al., 2015, Bournival et al., 2017, Wang et al., 2015, Mikhlin et al., 2015, to cite only a few), the modern era presents new challenges to the primary raw material industry, including questions regarding sustainability of mining operations accompanied by a need to improve the process efficiencies due to declining ore grades (Edraki et al., 2014).

Jan 1, 2019

By Simon C. Dominy, Ian M. Platten

"Abstract - Gold-bearing quartz reefs commonly show extremely erratic and unpredictable grade variation, although gross geological continuity may be good. This type of variation is often described as being nuggety or having a high nugget effect and can be measured quantitatively using the semivariogram. Understanding of geological features such as reef texture and structure will provide improved models for the interpretation of assay data, drill core descriptions, etc. In this paper, a case study from the quartz-hosted gold occurrences in the Gwynfynydd mine, United Kingdom, is described. The work provides a starting point for models of lateral variation and demonstrates the types of structural and textural features that may be sought to give clues to the prediction of gold distribution in similar deposits. Gold deposition at Gwynfynydd is primarily associated with the reef footwall. The host veins form a discrete group of structures that may have been emplaced early in the sequence of quartz veins forming the reef. This potentially exposes them to a maximum number of dissection events during repeat dilations of the lode. Gold was deposited in the local porosity at extreme concentrations, equivalent to kg/t grades, when the host fissure had become filled with a porous framework of crystalline quartz and sulfides. Distribution of porosity varied laterally along the vein as the result of the formation of clump-like growths of minerals from the vein walls. The growth style is relevant to the distribution of gold although it may not be relevant to the occurrence of gold in a particular vein. The preservation of pores with some connectivity late in the vein fill sequence may be important in permitting continued but slow fluid flows. This facilitates effective fluid reaction with wall rock-derived methane, thus changing the relative rates of gold and quartz deposition in favor of gold. The textural studies explain the first-order control of nugget distribution at Gwynfynydd but do not allow for prediction and optimization of the resource estimation process. This is principally because of the very low geological continuity and poor predictability of the high-grade pockets. Nonetheless, the work does provide a clear geological explanation for the erratic nature of the gold. It indicates textures and structures that can be used to determine geological continuity of the goldbearing elements within the gross reef envelope."

Jan 1, 2001

By C. Pawlik, R. T. Jones

Cobalt occurs together with copper in the southern African copper belt, and a large portion of this cobalt ends up in copper smelting slags, mostly dissolved in oxide form. It is possible to achieve high recoveries of cobalt by reductive smelting of the copper slags, using some form of carbon as a reducing agent in an electric furnace. For example, a 40 MW DC arc furnace was operated at Chambishi Metals in Zambia from 2001 to 2008, and demonstrated cobalt recoveries of around 80% from slag to an iron-rich alloy containing copper and cobalt. The alloy was atomized prior to leaching. With the recent increase in demand for cobalt (and the resulting high metal prices), there has been increasing interest in this process route. There is also an alternative hydrometallurgical process for recovering the valuable metals from the slag. The choice between these process options requires a trade-off between capital and operating cost and environmental acceptability. This paper examines the potential for cobalt recovery from slags, and outlines various process options. INTRODUCTION Cobalt has had a number of important uses in society since antiquity, and its principal use has changed dramatically over time. Since at least 2250 BC, cobalt-based pigments (cobalt blue) have been widely used to colour manufactured goods such as glass and pottery. Later, cobalt became known for its magnetic and wear-resistant properties and high-strength alloys, and most of the cobalt produced was consumed in the production of cobalt-based superalloys. The greatest recent growth in cobalt demand is due to it being essential to the rechargeable lithium-ion batteries used in consumer electronic devices and increasingly to drive electric vehicles. Cobalt is usually produced as a by-product of copper or nickel. The copper belt in the Democratic Republic of the Congo (DRC) and Zambia supplies most of the world's cobalt production. In 2018, the DRC was expected to produce 90 000 tons of the world total of 140 000 tons of cobalt (Shedd, 2019). This paper focuses on the southern African copper industry, and specifically the cobalt that is able to be produced as a co-product from this. A BRIEF HISTORY OF SOUTHERN AFRICAN COPPER SMELTING Copper deposits in South Africa have been documented since at least 1685, when the Cape governor, Simon van der Stel, ‘discovered’ the 'Copper Mountain' at Springbok. South Africa's first public commercial mining company (imaginatively called the 'South African Mining Company') was established in Cape Town in 1846, to exploit the rich copper resources that were believed to exist in Namaqualand.

Jan 1, 2019

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By Fernando Canales

In the last decade a great dealt of attention has been paid to the chemistry of polynuclear gold derivatives with a central heteroatom, not only from the experimental and structural but also from the theoretical standpoint (1). Interesting hypercoordinated species of the type [C(AuPR3)5]+, [C(AuPR3)6]2+, [N(AuPR3)5]2+, [P(AuPR3)5]2+ and [P(AuPR3)6]3+ have been described (2), apart from other complexes with more conventional stoichiometry, and all have in common the presence of gold-gold interactions of ca. 3 Å. Usually, the chemistry of the first row elements of the p-block is known to follow classical rules of bonding, and only in cases of extreme electron-deficiency has the traditional electron count to be reconsidered to account for special types of molecular or solid state structures. Many of these heteroatomcentered complexes are electron-deficient and the gold-gold interactions provide a significant contribution to their stability. The attraction between these closed-shell systems has recently captured the attention in inorganic and organometallic chemistry (1). P. Pyykkö has summarized the available theoretical and experimental evidence of intra- and inter-molecular interactions between heavy metal atoms, such as Au(I) (3). In general, when heavy metals are involved in such interaction, the closed-shell attractions are of metallophilic or van der Waals type, as has been found for d8, d10 coinage-metals, and d10s2 centers. Experimental evidence for the aurophilic Au(I)???Au(I) attraction is available from crystallography, NMR and Raman spectroscopies, and optical spectroscopic measurements of the interaction strength (4). It is manifested in molecular conformations with relatively close Au???Au interactions of ca. 3 Å, whose strength has been estimated at ca. 25-50 kJ/mol (5). These attractions are weaker than most covalent or ionic bonds, but stronger than other van der Waals bonds and comparable in strength to typical hydrogen bonds. The phenomenon cannot be satisfactorily explained by classical theories such as hybridization (3). From a theoretical point of view, the attractions close to equilibrium distances are caused by dispersive interactions together with relativistic effects (6). The attractive contributions are dominated by pair-excitations from the heavy metal, such as gold, strengthened by relativistic effects. In all the cases where there are inter- or intramolecular metal-metal attractions, the correlation effects are essential; if they are omitted, at the Hartree-Fock (HF) level, repulsive interactions are obtained (6). Hence, it is necessary to use at least second-order Møller-Plesset level (MP2) methods for the dispersive forces, which are included in the electronic correlation effects (7).

Oct 1, 2003

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

INTRODUCTION When Victoria became queen in 1837, that technical wonder of the 19th century—electricity— had progressed from being an exciting physical curiosity and was now a field of intense scientific investigation, invention and application. Its role in electrochemistry had been brilliantly quantified by Faraday in 1833–1834, and his earlier discoveries in electro-magnetism were to lay the foundations of electricity generation and the electric motor. In this age of electrical experiment, silver electro-plating emerged as a popular decorative art, at first using batteries to provide the deposition current, superseded by dynamos in the early 1840s. The decorative chemical and electroplating of precious metals was largely pioneered in England by the firm of G.R. Elkington and Co., founded in Birmingham by George Richards Elkington (1801–1865) in 1832, and protected by a series of patents which helped the company establish a leading position in the new field of ‘electrometallurgy’. In the same decade, the technique of electrotyping emerged, the first application of electro- forming by electrolytic deposition. Simultaneously invented by Spenser in England and Jakobi in Russia, but generally claimed for Jakobi, electrotyping involved plating a thick copper layer on to an electrically conducting mould wall embossed or incised with a pattern or profile which would consequently be replicated on the copper deposit—essentially a method of casting by electro-deposition with the mould wall as cathode. Woolrich’s invention of the low voltage magneto-dynamo in 1842 eliminated the need for batteries as a continuous source of deposition power, opening up the possibility of making more massive electroplated deposits, and by the mid-point of Victoria’s reign in 1869, the work of Wilde, Wheatstone and Siemens had produced the self-excited electro-dynamo, capable of higher voltages and yet greater deposition power. In this early Victorian period copper was extracted and refined by methods which had developed step-by-step over many decades. Only relatively rich copper ores containing more than, say, 6% Cu were economically useful, and the final copper product was far from pure. Copper production in Britain was located principally in the Swansea area of South Wales, based upon the ‘Welsh process’ of reverberatory batch smelting and refining, using locally mined coal and ore imported from Cornwall and elsewhere. Silver was an important by-product. Much of the output was exported and South Wales remained a principal supplier to the world copper market until the 1890s. It was here at Pembrey, a few miles west of Llanelli, that a new primary copper smelter was stablished in 1849 under the name Mason and Elkington, arguably to supply the Elkington company’s market for electrotype products.

Jan 1, 2019