Search Documents

By Daniel J. Schulze

Eclogite is an important source of diamond in the upper mantle, but is more localized than peridotite. Using eclogitic minerals in kimberlite and diamond exploration is also more problematic than using the well-known peridotite-derived indicator minerals Cr-pyrope and magnesio-chromite. The problems include color similarities between orange garnets from eclogites, Cr-poor megacrysts, and crustal garnets, chemical similarities with Cr-poor megacryst suite garnets (speci?cally elevated Na2O contents), and low abundance of eclogite garnet xenocrysts in most known kimberlites. Chemical screens must be used carefully to distinguish between varieties of orange garnetsin exploration samples. For example, most orange garnets of crustal origin have >22 wt% FeO, with mantle eclogite garnets having lower values. Na2O-bearing garnets from the Cr-poor megacryst suite can be distinguished from Na2O-bearing garnets from diamondiferous eclogites by the elevated TiO2contents of the former. The low abundance of eclogite garnet xenocrysts in kimberlites worldwide, however, may dictate that use of eclogite garnets in diamond exploration in most cases be restricted to advanced stages of kimberlite exploration and evaluation of kimberlite diamond potential. Cr-pyropes, Mg-ilmenites and Cr-rich chromites are more useful than eclogitic garnets in most stages of diamond exploration. If orange garnet xenocrysts are sought in a kimberlite exploration program, those from the Cr-poor megacryst suite will be more useful than eclogite derived garnets, due to the typical great abundance of the former, although they carry no information of the diamond potential of the host kimberlite.

Jan 1, 1997

By D. R. Lentz, C. J. Beaumont-Smith, S. H. Mcclenaghan

"Abstract - The Louvicourt Au-Ag-Cu-Zn-Pb sulfide deposit is hosted by a Middle Ordovician calc-alkaline sequence of aphyric rhyolite flows and associated fragmental rocks at the top of the Flat Landing Brook Formation. The Zr/TiO2 (average = 0.110) and Y/TiO2 (average = 0.021) ratios in the footwall felsic volcanic rocks are consistent with known values for the Reids Brook member. The deposit consists of two concordant lenses of semi-massive to massive sulfides, approximately 150 m long and up to 9 m thick, which represent a fold repetition of a single exhalative horizon. The deposit contains a geologic resource of 136 000 tonnes grading 1.2% Pb, 1.0% Zn, 0.4% Cu, 90.9 g/t Ag, and 0.96 g/t Au; the deposit locally contains elevated Au (2.9 ppm) and Ag (320 ppm) contents. A laterally continuous iron formation that contains barite caps the deposit, and is gradational vertically and laterally into laminated siltstone. The exhalite confirms the stratiform nature of this deposit, but a large percentage of sulfides occur as late replacements of altered felsic fragmental rocks in the footwall. Abundant examples of colloform pyrite and perlitic and spherulitic textures in volcanic clasts are well preserved. The base- and precious-metal content of the Louvicourt deposit is atypical of the Bathurst Mining Camp (BMC). Reported assay data (n = 27) indicate an average Pb/Zn ratio of 2.6, the highest in the BMC (average = 0.39). Lead exhibits a strong Spearman Rank correlation (r' = 0.92) with base metals throughout the sequence, indicating a preponderance of galena in both the stockwork and stratiform zones. The Ag and Au contents in this deposit are among the highest in the BMC and exhibit a Au-Ag- Cu-Pb association. Barite-rich exhalative pyrite exhibits a moderate Au correlation with Ag (r' = 0.77; n = 10) and Cu (r' = 0.76) and occurs in portions of the exhalative sulfides that are enriched in Pb. Chemical exhalative rocks are conformably overlain by trachy-andesitic volcaniclastic (possibly pyroclastic) rocks that are assigned to the Little River Formation. These are enriched in Nb (average = 38.4 ppm) and P2O5 (average = 0.17 wt.%), and have much lower Zr/TiO2 (average = 0.056) and Y/TiO2 (average = 0.0062) relative to rocks higher in the hanging wall. The intermediate volcanic rocks are conformably overlain by massive to pillowed basalt flows and related hyaloclastite that have Nb/Y = 0.60 and high TiO2 contents (average = 2.8 wt.%). This chemistry is consistent with rocks of the Brunswick Mines member (Little River Formation), except that these rocks are considerably enriched in P2O5 (average = 0.82 wt.%). This syngenetic exhalative deposit is unique for the BMC with a high Pb/Zn and elevated Au and Ag contents, as well as an epithermal signature (Sb-Ag-Au-Tl-Hg), analogous to high sulfidation volcanogenic massive sulfide deposits. Its intimate relationship with an emergent felsic dome (Flat Landing Brook Formation), chlorite-silicate-oxide-sulfide exhalite (locally hematitic), and the abundance of barite are classical features of many of the Kuroko deposits."

Jan 1, 2006

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"Abstract — The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units. © 2012 Canadian Institute of Mining, Metallurgy and Petroleum. All rights reserved."

Jan 1, 2012

By John Starkey

"During the period June 2007 to March 2007, John Starkey of Starkey & Associates (Starkey) worked in Russia for High River Gold, supervising the engineering design work that was being done at the IRGIREDMET Research Institute, in Irkutsk Russia. The work entailed moving the Newmont No. 4 mill from Elko, Nevada to Berezitovy, a mine site north and west of the city of Skovorodino, in the Amur Region of Siberia. This was a grass roots project and required construction of all phases of the infrastructure and process facilities that are associated with a 5000 t/d open pit mine and CIP mill.During the course of this engineering design exercise, many aspects of doing business in Russia were encountered, with regard to laws, norms, and business practices. This paper discusses many of these findings. Also by living in Irkutsk, many observations on Russian life and social customs were made and these merit discussion from a general interest point of view.Prior to going to Russia, another engineering and ore testing firm (TOMS) had approached Starkey to find out if Starkey could assist them in upgrading their SAG ore testing procedures to Western standards in order to offer their clients turnkey projects, that included reliable SAG and AG grinding. TOMS was aware that Starkey had invented the SPI test but did not know that the SAGDesign test had by then been fully developed and was being offered commercially as the most accurate way in the world to design new grinding mills. They were also unaware that this new testing method had been patented by Outokumpu (now Outotec) and that this method allowed them access to a design method, through Starkey, that would lead to a manufacturer’s guarantee (by Outotec) of throughput and grind for any new semi-autogenous or autogenous grinding circuit, with or without ball mills.When Starkey started working at IRGIREDMET in June 2005, they also made a request to add a design method for SAG mills that would be considered acceptable to Western clients. From these requests, presentations were made in Russian to both institutes and each decided to join the SAGDesign Consulting Group as satellite members and buy a SAGDesign test mill to use with their Bond Ball Mill Work Index mills, to provide SAGDesign testing services. To complete the service, contracts have been put in place for Starkey to use these results to design new grinding equipment and to train engineers at TOMS and IRGIREDMET how to do this work.Starkey also undertook to train engineers at both labs to go into the field and to take the samples for SAGDesign testing programs. It is here where the SAGDesign testing service upgrades other grinding test programs because the samples to be used for design are professionally chosen, and the results will be much more likely to produce a satisfactory design. Starkey is a mining engineer and is uniquely qualified to do this task. This and the SAGDesign test are the key components that lead Outotec to offer a performance guarantee for mills designed by Starkey."

Jan 1, 2008

By Dave Bulled

"This paper describes the design of an SABC grinding circuit using CEET technology applied to grindability data produced from testing 100 samples and distributed across the blocks of a mine plan using a geostatistical approach. The data distribution required the identification of the location of the sample points and a geological plan of the 130 million ton Ruby Creek orebody together with a mine plan of about 11000 blocks to be mined during the proposed 18 year life of the mine. The mill design was then made with consideration for the estimated hardness of each block in terms of both SAG and Ball milling with allowance for annual periods when the ore is harder to grind. Operating specifications were selected to achieve an optimum of capital and operating costs through use of the CEET program. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the hardness estimate of each block of ore in the mine plan. The final design could then include a quantification of risk and determination of safety factors based on the accuracy of block hardness estimates and CEET model fitting.INTRODUCTIONThe traditional approach to plant design involves the extensive testing of a single large composite sample or a small number of composite samples that are reputed to represent the ore body. It is accepted that the tests used can accurately measure in the laboratory the grindability of the sample by a process representing that to be used in the plant. The size of equipment required to achieve a specified throughput and product size is then calculated from one of a variety of models that have been developed by metallurgists over years of trial and error. Since these tests and models are tried and tested, they are accepted as reasonably precise; however during the operation of the resulting plant the design is sometimes found to be inadequate. It is then suspected that the flaw in the design process lies in the samples not being sufficiently representative of the ore body, since using only a single or small number of composite samples does not recognize the variability of the hardness of the ore, nor does it allow for the lack of precision in the hardness value used in the design.This paper outlines a design procedure suited to an orebody that is described by a geostatistical analysis of a reasonably large number of small samples of drill core. The analysis required the identification of the location of the sample points and a geological plan of the orebody, together with a mine plan of the blocks to be mined during the proposed life of the mine. The mill design was then made using the estimated hardness of each individual block with an allowance for annual fluctuations in the grindability of the ore. The geostatistical analysis assigned a statistical error to the hardness estimates of blocks and of each production year such that the final design included risk estimates and safety factors based on the possible errors that arise from having a limited amount of sample data (Kosick et al. 2002)."

Jan 1, 2007

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By E. Roman, M. Brissette

"For its end of life, Kemess Mine processed its difficult-to-treat hypogene ore from the east pit, which is a lower grade copper and higher pyrite content gold ore. Metallurgical testwork showed that improvement was possible with finer grinding. In July 2010, small grinding media were introduced into the regrind mill resulting to a nearly 50% decrease of the power draw with a finer grind, an increase of 1.1% in the final copper grade, an increase of 1.2% in copper and 2.9% in gold recoveries at the cleaners. The overall recoveries of copper and gold increased by 0.6% and 1.3% respectively.INTRODUCTION Kemess Mine was located at 430 km North West of Prince George in North Central British Colombia. Its production started in May 1998 by Royal Oak Mines and was acquired by Northgate Exploration in 2000. Kemess reached its end of life production with its last of production on March 9th, 2011. The concentrator nominal capacity was 56,000 TPD consisting of a primary gyratory crusher feeding two identical conventional SAB circuits totalizing 35,840 kW available for grinding. Rougher flotation consists of four parallel rows of eight 130 m³ tank cells to produce a concentrate of 2% Cu and 6 gr/t Au which was pumped to a 5 m x 10.8 m regrind ball mill. The regrind installed power was 4,480 kW to generate a final grind of 80% passing 40 microns. This product fed the two stage cleaner flotation circuit, first stage being two parallel rows conventional 17 m³ Denver cells and second stage, two 3.3 m x 11.0 m flotation columns in series, designed and constructed by Kemess, to produce a 22% copper concentrate grade. The cleaner flotation middlings were returned back to the regrind mill (Froehling, Mohns, Roman & Grady, 2005; Froehling, Mohns, Rajwani & Fullam, 2007). The large copper-gold porphyry deposit was composed of 15% of oxidized supergene and leach cap ore and 85% of hypogene ore having three major alteration zones, mainly characterized by their sulphur/sulphide content. Chalcopyrite is the main copper mineral species with minor bornite. Gold was mainly present as free gold or electrum. The first alteration zone consisted of a phyllic alteration characterized by moderate and intense sericite alteration which had the highest mill throughput and twice the mine grade when in contact with the supergene horizon. The second zone consisted of a potassic alteration characterized by more competent groundmass and moderate to intense quartz stockwork which had a slightly lower mill throughput. Finally, a third alteration found beneath and on the east side of the deposit having almost no quartz stockwork and hardened groundmass, sulphide content is two to four times more. This zone had the lower mill throughput with significant drop in the mine average gold and copper grade. Through its mine life, the average life of mine copper head grade was 0.21% Cu and 0.64 gr/t Au. Head grades began to decrease from 2008 to be substantially lower in 2011 as shown in Table 1."

Jan 1, 2012

By P. Taskinen, D. Lindberg, H. Viitala

The formation of copper chlorides in flue dust or deposits in heat recovery boiler of copper smelters or waste-fired boilers may lead to formation of corrosive partially molten deposits on walls and heat exchangers of the boilers. These deposits can contain various other metals, such as alkalis, Fe, Zn, Pb together with oxides and sulfates. In the present study, a thermodynamic model for copper-containing binary and ternary metal chloride systems within multicomponent CuCl-CuCl2-FeCl2-FeCl3- PbCl2-ZnCl2 system has been assessed and optimized based on own experimental phase equilibrium data, as well as literature data. The thermodynamic properties of the liquid phase was modelled using the quasichemical quadruplet model and a thermodynamic database was optimized to predict all available experimental data within the experimental error limits. The thermodynamic database allows for more accurate predictions of potential corrosion-related issues in various heat recovery boilers and waste-fired boilers due to formation of copper chlorides. INTRODUCTION In the copper flash smelting, flue dust can cause severe problems in the gas train, used for separating dust from the SO2-rich off gas, by forming corroding accretions on the walls of the heat recovery boiler. Formation of dust build-ups in the boiler need to be cleaned regularly and potential corrosion damage checked, requiring costly and unscheduled shutdowns of the flash smelting process. Compounds of copper and zinc among other elements having high vapour pressures may volatilize during the smelting of the copper concentrate, forming dust when the process gas cools down. Also, particles of solid or liquid iron oxides originating from the ore get transported with process gas to the heat recovery boiler as a result of entrainment in the flue gas (Miettinen, 2008) The dust deposit build-ups on the boiler walls are formed partly by direct impact of particles and partly by vapour condensation on the boiler walls. The initial deposition takes place by the condensation of vapours that contain zinc, lead, arsenic and other metals having high vapour pressures. Also, low melting point eutectic components of alkali salts such as chlorides and sulphates can act as sticky cohesive particles attaching to the boiler walls. The fine particles landing on the surface of the porous dust deposit layer react in the SO2-rich atmosphere of the boiler to sulphates. The process gas within the boiler contains SO2, O2, SO3, H2O and N2 that diffuse into the porous accretions to form a stagnant gas layer within the dust deposit structure. The composition of this gas layer may differ greatly from the composition of the process gas that is flowing on the surface of the accretion layer. Locally HCl and H2SO4 are formed and even a reducing atmosphere may exist within the dust deposit layer, allowing new reactions to take place. The local micro-atmosphere may enable metal sulphates to be reduced to secondary sulphides and even metallic components. Within the accretion layer, components may be formed that would not be stable in the gas atmosphere inside the boiler (Miettinen, 2008). This may be the mechanism by which for instance chlorides of Cu, Fe and Zn are formed within the deposit layer.

Jan 1, 2019

By Eugen Gluck, Gus Van Weert, Peter Kondos

"Microwaves have the capability to heat up sulphides, especially clusters of particles of approx. 1 mm. Some sulphides absorb microwaves more readily than others. Molybdenite is especially effective in this regard, possibly due to its flaky nature and/or electrical conductivity. Even where it occurs in low concentrations in a deposit, individual rocks may be ore grade due to the high monetary value of MoS2. Such rocks often result from crushing mined veinlets or stockwork, or are contained in the cutoff grade fraction of ROM. Machine segregation of rocks high in MoS2 by infrared sensors after microwaving could therefore advantageously be used to upgrade lower grade ore between Mine and Mill. This would reduce the size of the latter, and thus its CAPEX and OPEX. Such upgrading could also yield shipping ore for a distant Mill, or extend ore reserves.Barrick Gold Corp. has been supporting the development of MW/IR sulphide sorting for the past three years. The results of MW/IR sorting work on molybdenite and other (pyritic) ore samples from a variety of sources are being presented here.INTRODUCTIONThis paper looks at mechanized, i.e. machine ore sorting technologies currently available and under development, and what conditions would be needed for the potential application of such ore sorting to sulphide mining and milling. Current machine sorting involves no-contact sensing technology for rocks, and signal processing after sensing to activate airblast segregation of certain rocks, normally the smallest mass to keep compressed air costs down.The forerunner of modern sorting is probably magnetic separation, which utilizes an inherent property of certain ores to divert it into mag and non-mags fractions. Radiometric ore sorters, which have been applied successfully for decades in the pre-concentration of uranium ores (Wotruba and Riedel, 2006) initiated modern sorting. In the 90’s, sensor-based machine sorting became a viable means of increasing the overall economic recovery of a resource. This technology became driven by the availability of low cost computing equipment and the concurrent development of algorithms, and by the availability of extremely fast response sensors and air actuators, allowing the sorting equipment to run faster, dropping the cost per tonne. It has been in industrial minerals processing that rock sorting has been most widely adopted, not really surprising. Liberation occurs on a different scale than in the base metal industry. Most industrial minerals are mined from massive deposits, requiring (in the past) no upgrading. Many of these operations now run into product contamination problems, which ore sorting can solve. One illustration: in Finland, a quarry is separating limestone from dolomite at 500 tonnes / hour, with individual rocks weighing up to 15 kg. Many of these industrial minerals operations have stockpiles of earlier discarded below-quality rocks, now being reprocessed with the help of ore sorting. The economics of this are very favourable, going from zero or negative value (stockpiles can not be left when closing the mine) to full product value for at least a portion of the stockpile. This suggests that in the future the economics of overburden sorting could become attractive under the right circumstances and such treatment could well become an integral part of open pit mine development."

Jan 1, 2009

By J. A. McLennan, J. M. Ortiz

Nickel laterite deposits are typically formed from tropically weathered mafic-to-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs) or representative dozer regions (RDRs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate “optimum” RDR mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each RDR. The optimum mining elevation is the elevation where the lowest summed cost of “accepting dilution” and “wasting ore” occurs. The reported RDR dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation. The reported RDR lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum RDR mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Jan 1, 2006

By Louis J. Cabri

"Mineralogical evaluation of ores containing platinum-group elements (PGE) is fraught with difficulties because of the low grades (often 1-3 g/t PGE), dispersal of PGE (usually as finegrained platinum-group minerals [PGM]), as well as occurring in solid solution in some base metal sulphides (BMS) such as pentlandite and pyrrhotite. Mineral processors not only need to know how the PGE are distributed, that is, their mineralogical distribution, but the grain sizes of the PGM, and especially the associated minerals.After obtaining a representative ground sample, common approaches include studying a large number of polished or polished thin sections, concentration of the PGM and sulphides by different gravity methods (e.g., heavy liquids, elutriation, micro-panning) and study of the produced concentrates. Unfortunately, these methods often do not produce concentrations that are sufficiently representative of a particular ore. The newly developed patented technology of hydroseparation (Rudashevsky et al., 2002) is especially effective at making concentrations of PGM over a wide range of concentrations (down to <300 ppb Pt+Pd+Au) and size fractions, including <45µm (down to a few micrometres in size), a size range not possible by other techniques. This water-based environmentally friendly laboratory technique provides a large amount of data from samples, which can range from 5 to 1000g, giving confidence to extrapolation of results to bench-scale and larger test work, especially when combined with quantitative image analysis to determine modal percent of major minerals and mineral liberation data, needed to predict the minimum (K80) and optimum (K40) grinds. INTRODUCTIONThe invention of the electron microprobe in the early 1960’s and scanning electron microscopes (SEM) with energy dispersive spectrometers (EDS) in the 1970’s presented mineralogists with powerful tools permitting them to obtain chemical and surface area data on minute amounts of minerals in situ, in a non-destructive manner. An area of process mineralogy that has very much benefited from this new technology was the characterization and understanding of PGM species, resulting in rapid growth of newly characterized species (Figure 1). Recognition of the first PGM may be ascribed to the Spanish explorer Ulloa in 1748, who described native platinum from South America. The second PGM (laurite, RuS2) was only recognised in 1866 by Wöhler in placer samples from Borneo (now Kalimantan) and the third (sperrylite, PtAs2) by Wells in 1889 from the Sudbury Ni-Cu sulphide deposits. The discovery of the important Pt-Pd deposits in the Bushveld Igneous Complex led to the characterization of the important Pt-Pd sulphides (cooperite, PtS2 in 1928 and braggite, (Pt,Pd)S2 in 1932). By the early 1960’s, only about 20 PGM were recognised, and many later proved to be poorly or incompletely characterized. Thus, the introduction of electron probe microanalysis (EPMA) led to a 50% increase of known PGM, as shown in a 1972 review on PGM (Cabri, 1972). At the time of the next review in 1981 (Cabri, 1981) the number of known PGM had grown to 75 and as of 2002, it had increased to 109 (Cabri, 2002). However, it is the author’s experience that less than about 25 PGM may be considered to be “common”, i.e., found in many different deposit types, as shown in Table 1, but usually only some of these occur in any one particular deposit."

Jan 1, 2004

By Andrew Bamber

Between the early 20th Century and the present, the production of mined copper ore has increased from tens of millions of tonnes per annum to several billion tonnes per annum, an unprecedented increase. Contemporaneously, the average grade of mined copper ore has declined from over 2% to approximately 0.5%. Again, in parallel, the price of copper has increased dramatically to reflect the increasing cost of extracting and beneficiating such large amounts of low-grade ore. Within the period the copper price however exhibited several periods of intense volatility, driven by interrelationships between demand and supply, themselves strongly driven by periodic industry developments in the fields of exploration, ore extraction, mineral processing and extractive metallurgy. It is notable that these periods of intense innovation exhibit a strong correlation to preceding periods of price, demand or production volatility. This paper examines key trends in each theme between 1900 and 2018 and draws strong conclusions as to the interrelationship between them. INTRODUCTION The production of copper metal has increased from around half a million tonnes per annum to over fifteen million tonnes per annum over the course of the 20th Century. Contemporaneously, the average grade of copper ore mined has declined from over 2% to approximately 0.5% copper by weight. As a result, the volume of Run-of-Mine (ROM) copper ore required has increased from around ten million tonnes per annum to over a five billion tonnes per annum over the period, an unprecedented increase. The adage is that demand drives supply, that prices rise in times of high demand and/or short supply, and that prices fall when supply catches up with demand. The market sellers in biblical times knew this well; mediaeval market sellers equally. Dutch tulip sellers in the 1600’s experienced both in extremis — much to their dismay — and the great industrialists and early capitalists of the industrial revolution knew this also. Mining recently went through a cycle where investors and producers both believed that the “old” rules did not apply any more and that the industry was in a “supercycle” where prices would continue to rise on the back of increasing demand. However, as the GFC of 2008–2011 showed, this was not to be. Another adage says that we constantly innovate to lower costs of production. Is this true? Do we only innovate to lower cost? Has the true cost of producing copper actually gone down over the century? Or are there other balancing forces at play? Herb Kellogg, in his Centenary address to the American Institute of Mining Engineers (now SME), categorized two types of innovation: ‘Bigger and Better’, and ‘New Process’ (Kellogg, 1970). ‘Bigger and Better’ allows increased production at presumably lower cost; ‘New Process’ supports the same result at presumably the same scale, but at significantly enhanced efficiencies and (therefore) lower cost. It is suggested that both types of innovation are constantly and interchangeably required to achieve the kind of scale-up, at achievable operating and capital cost that the industry has achieved over the period. What can be shown, over this last Century and a bit, is that supply and demand are indeed inextricably linked, price and demand are linked, but so are price and cost of production. And the innovation required to sustain that weaves in between them all, cost-effectively increasing production capacity or lowering the cost of production at the same throughput, and sometimes both.

Jan 1, 2019

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By Warwick D. Bullen

Gold mining in the Yellowknife area of the Northwest Territories started long before the concept of sustainability entered the academic literature and by the time the term enjoyed widespread public acceptance, the Yellowknife gold mining industry was in its sunset years. Nevertheless, the city of Yellowknife will long outlive the gold mines that it was founded on, demonstrating that not only can mining build sustainable communities, but that sustainable mining as a concept is an entirely valid precept. To this effect, the authors examine the complex economic and social aspects of the gold mining industry in the Yellowknife area over the last 70 years.

May 1, 2004

By Marius Jacobs

"Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a "plateau" and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have "exemplary" safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA’s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization’s mindset? What characterizes these organizations’ decision-making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensiveresearch since 1997 of organizations that suffered unexpected disasters.The Piper Alpha Oil Rig disaster in the North Sea, on the 6 July 1988, was one of the most pivotal events in safety around the world. It changed the thinking and focus of governments, whole industries and led to numerous books and papers. It resulted in new legislation, textbooks and a critical self-examination by the oil and gas industry.In short, an explosion and fire occurred when a pipe started leaking gas and ignited. A temporary flange, with no safety valve, was used to block off this pipe during a maintenance operation the previous shift. The permit to advise operators not to start the pumps on this line was misplaced and lost. Several deficiencies, problems and system failures coincided. A key factor was that the water deluge system was inoperable at the time and failed to extinguish the large fire that erupted, followed by an even larger gas explosion. The accommodation unit, situated on top of the oil rig, was the main "killing field" - most men gathered here to await instructions (which never came) and where they died from smoke inhalation. Later, a large explosion of the gas pipeline from an adjoined rig exploded and killed more people.The line of events and the associated system failures are all very relevant in the analysis of the accident, and provide the only insight into what caused the accident. But much "further back", inside the organization’s culture, lurks more dark matter. The first inclination is to ask what was "deficient" in the culture. Did they not care enough about safety, or about their people? Did they have a culture where production decisions were more important than safety considerations? Did they ‘coerce’ supervisors and employees to ignore safety precautions or did they just "fly by the seat of their pants"?Not surprisingly, it is very difficult to identify the true nature of the culture in that business because in such an aftermath of death and destruction, no one dare say that the safety culture was a ‘positive one, focused and caring’ or that the company was doing well in safety and that this is only a freak accident. Indeed, there were many deficiencies in the organization’s systems and procedures, such as the permit to work system.But there are some niggling questions: How is then that the Piper Alpha Oil Rig was actually considered the company’s most productive and safest oil rig in the North Sea? Why would this rig win a safety competition, 6 months before the disaster, with the deficient permit as its most outstanding successful system?"

Jan 1, 2014

By M. Abzalov

"Control of analytical data quality is usually referred to in the mining industry as Quality Assurance and Quality Control (QAQC), and involves the monitoring of sample quality and quantification of analytical accuracy and precision. QAQC procedures normally involve using sample duplicates and specially prepared standards whose grade is known. Numerous case studies indicate that reliable control of sample precision is achieved by using approximately 5% to 10% of field duplicates and 3% to 5% of pulp duplicates. These duplicate samples should be prepared and analyzed in the primary laboratory.Bias in the analytical results can be identified by inclusion of 3% to 5% of the standard in each sample batch. Several different standards are used, with values spanning the practical range of grades in the actual samples. A blank (a sample in which the concentration of metal of interest is below detection limit) should also be included. Standard samples alone cannot identify biases introduced during sample preparation, and therefore approximately 5% of the duplicate samples (coarse rejects and pulp) should be processed and assayed at another, external, reputable laboratory.This paper discusses techniques used for estimation of errors in precision and accuracy, and overviews diagnostic tools. It is shown that one of the most commonly used methods, the Thompson-Howarth technique, produces consistently lower results than other methods. These results reflect the nature of this method, which relies on the assumption of a normally distributed error, and thus produces biased results when errors have a skewed distribution. This study concurs with the suggestion of Stanley and Lawie (2007: Exploration and Mining Geology, v. 16, p. 265-274) to use the average coefficient of variation (CVAVR(%)) as the universal measure of relative precision error in mine geology applications: Le contrôle de la qualité des données analytiques est habituellement désigné sous l’appellation d’Assurance et Contrôle de la Qualité (ACQ), elle implique le suivi de la qualité des échan¬tillons et la quantification de la reproductibilité et la précision analytiques. Les procédures des pro¬grammes d’ACQ impliquent habituellement l’usage de duplicata et de standards analytiques dont la teneur est connue. Plusieurs études de cas indiquent qu’une bonne fiabilité du contrôle de la précision des échantillons est atteinte par l’usage de 5% à 10% de doublons sur le terrain et de 3% à 5% de doublons de pulpe. Ces duplicata devraient être préparés et analysés au laboratoire principal.Un biais des résultats analytiques peut être identifié par l’inclusion de 3% à 5% d’échantillons standard dans chaque envoi d’échantillons. Plusieurs standards sont utilisés, avec des valeurs couvrant l’étendue des teneurs habituellement rencontrées dans des échantillons réels. Un blanc (un échantillon dans lequel la concentration d’un métal donné est sous la limite de détection) devrait aussi être inclus. L’emploi exclusif d’échantillons standards ne permet pas l’identification de biais résultant de la préparation des échantillons, de telle sorte qu’environ 5% des duplicata (rejets grossiers et pulpes) devrait être traités a un autre laboratoire indépendant et fiable.Cet article passe en revue les techniques utilisées pour évaluer l’erreur liée à la précision et a la reproductibilité, et effectue aussi un survol de divers outils diagnostiques. Il ressort de cet examen qu’une des techniques les plus fréquemment utilisées, la méthode Thompson-Howarth, fournit des estimés systémati¬quement inférieurs à ceux provenant des autres méthodes. Ces résultats sont un reflet de la nature de cette méthode, laquelle assume une distribution normale de l’erreur, biaisant ainsi les résultats lorsque l’erreur présente une distribution asymétrique. La présente étude recommande de privilégier l’usage du coefficient moyen de variation (CVAVR(%)) en tant que mesure universelle de la précision relative de l’erreu"

Jan 1, 2008

By Michael Stuart Parsons

The haulage cycle is the sequence which a haulage vehicle must first arrive at the loading area, then turn around and reverse into position. Once it is loaded, the vehicle leaves and travels to the unloading area, where again it must turn around and back up to unload. The cycle is repeated over and over again. The Vector Neutral truck is a rubbertired, self-propelled hauling vehicle designed such that it eliminates the requirement to turn around and back-up to either load or unload. Vector Neutral Truck Cycle: 1.) Travel from the load station to the dump station. 2.) Stop and dump load. 3.) Travel from the dump station to the load station. 4.) Stop and load. The Advantage is in the Difference: 1.) Shorter distance traveled. 2.) Fewer brake and steering actuations. 3.) Easier to automate. 4.) Easier to adapt for remote control operation.

May 1, 2003

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007