Search Documents

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By D. Berkley

The competitive pressure, the increasing energy costs and the environmental regulations impose substantial challenges to the definition of power plants serving industrial facilities. Primary mining and metallurgical facilities have even greater challenges because they are often located remotely, where the fuel supply can be a problem. The absence of a power grid imposes challenges on the reliability and quality of the electrical energy supply. In addition, the facilities usually require thermal energy too, not only electricity. This paper outlines these types of issues that have to be considered when defining a cogeneration plant integrated with a remote located industrial facility. It is addressed to the ?users? of cogeneration facilities rather than to ?generators.? The focus is on analyzing various site-specific design considerations to pre-screen the feasible cogeneration alternatives and minimize the number of options to be analyzed from the economics viewpoint. This approach could substantially reduce the engineering effort and schedule during the feasibility phase of the project. Part 1 of this paper (Berkley, 2003) provides a basic understanding of cogeneration plants of various types to establish a common language. Part 2 outlines and analyzes specific issues that could be of help in the definition of cogeneration installations for remotely located industrial facilities, with a focus on mining and primary metallurgical plants.

Mar 1, 2003

By Michael G. Nelson

Control of the feed provided to mineral processing facilities is a continuing challenge. Much effort is currently being devoted to overcoming these problems. These projects are usually described under the general headings of Mine-to-Mill Integration or Mine-Mill Optimization. It should be possible to combine the knowledge of ore type, mineralogy, and other characteristics (located in the mine modelling system), with the advanced capabilities of state-of-the-art mill control systems, to achieve an improved level of control in mineral processing, allowing optimization of the mill processes on an almost realtime basis. This is not happening because mill feed it is often treated as a uniform material, when in reality it varies in composition and characteristics. The University of Utah is investigating the use of odor sensors for maintaining traceability in ore production and processing. Odor sensors now used in food processing, environmental monitoring, and other applications can detect the presence of very small amounts (0.1 - 500 ppm) of some molecules. An assortment of such molecules could be used to ?tag? blocks of ore as they are mined, according to their respective characteristics. Then, as the ore came into the mill, an array of ?electronic noses? could be used to assess its characteristics in real time.

May 1, 2004

By W. G. Johnson

"As we move into 1983, Canada is not only in a deep recession, there are major changes taking place.International competition is growing fiercer.Major core industries such as automobile, steel, mining, oil, agriculture, forestry, fishing, major manufacturing and others are just not expanding.If and when recovery comes starting in mid-1983, as many predict, don't expect industries to suddenly resume former growth patterns. It's just not possible.Companies, by necessity, are becoming lean and mean, and they are still in the process of reducing staff to meet changing times and conditions. Many of the staff now being released may never return to fulltime work with a single employer, particularly if they cannot measure up to more exacting performance standards and management expectations.There are clear cut instances of people who lose a job for reasons beyond their control. A merger, the loss of function, or a major reorganization sometimes creates casualties of people who were excellent performers. Such people can survive well, based on the tongue of good report and with some help from associates or others. However, even good performers often have difficulty in adjusting to the rigors of finding a new job and to become their own personal salesman."

Jan 1, 1983

By D. Berkley

"The competitive pressure, the increasing energy costs and the environmental regulations impose substantial challenges to the definition of power plants serving industrial facilities. Primary mining and metallurgical facilities have even greater challenges because they are often located remotely, where the fuel supply can be a problem. The absence of a power grid imposes challenges on the reliability and quality of the electrical energy supply. In addition, the facilities usually require thermal energy too, not only electricity.This paper outlines these types of issues that have to be considered when defining a cogeneration plant integrated with a remotely located industrial facility. It is addressed to the “users” of cogeneration facilities rather than to “generators.” The focus is on analyzing various site-specific design considerations to prescreen the feasible cogeneration alternatives and minimize the number of options to be analyzed from the economics viewpoint. This approach could substantially reduce the engineering effort and schedule during the feasibility phase of the project.The front-end of the paper provides a basic understanding of cogeneration plants of various types to establish a common language. Subsequently, the paper outlines and analyzes specific issues that could be of help in the definition of cogeneration installations for remotely located industrial facilities, with a focus on mining and primary metallurgical plants"

Jan 1, 2003

By Ludwig M. Strah

"Wear is a universal problem and is present in all cases wherein one weighted surface moves with or relative to another surface. A practical description of wear as applied to mineral processing plants is outlined.With the advent of higher material and maintenance costs, more attention is being focused on the field of wear resistant linings. The aforementioned is magnified today as the production facilities continue to be designed to handle larger daily capacities. These changes, higher costs and larger plant handling facilities have necessitated the introduction of different materials and designs to combat the never ending battle against wear.In order that wear be understood, it can be relegated to two specific types:1 - Mechanical Wear - due to movement of one loaded surface relative to another.2 - Chemical Wear - more easily defined as corrosionMechanical wearMechanical wear can be subdivided into two basic forms:A.,Material movementB.,Material impactMaterial movement Abrasion is the result of, as earlier stated, the straight move¬ment of one loaded material relative to another.Material impact Is the striking effect when a mass strikes another from various angles and at various speeds. Impact can be severe enough to permanently damage and distort the basic component installed to overcome impact."

Jan 1, 1983

By Jean-Claude LeRoy, Herman Keller

"INTRODUCTIONEROCON's work is the reclamation of mine wastelands. It has had considerable experience in particular in the reclamation of gold mine tailings in the Canadian Shield since the latter part of the sixties when most gold mines were closing down.A typical example is the famous Hollinger Mine in Timmins which produced $566 million worth of metal from 1910 to 1968 and had left behind some 56 million tons of tailings covering about 1,000 acres which were reclaimed on very short order and are now lush meadows of agricultural quality.To date, practically all gold mine tailings have been reclaimed once and for all by establishing a permanent, self-sustaining and maintenance free vegetation cover.RECLAMATION & THE MINING TOWNSThe first appreciation of people in a mining community where the tailings have been revegetated will be noticing one day the elimination of dusty conditions that used to arise formerly on every dry and windy day. In that respect, EROCON encourages not only vegetating the tailings but also the immediate surroundings of the mills and plants themselves at active mines. The elimination of windborne dust will result in an appreciable decrease in maintenance costs of plant and machinery and more pleasant working conditions for all."

Jan 1, 1975

By G. H. Hope

"Pamour Porcupine Mines of Timmins, Ontario operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the area. The area milling concept was adopted by Pamour in 1971 and has been used successfully since then. The purpose of this paper is to discuss the advantages and the problems of area milling. Pamour Porcupine Mines Limited operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the Porcupine region. The area milling concept was adopted as the route to survival for Pamour and has worked successfully. HISTORICAL BACKGROUNDProduction of gold from the Porcupine region in Northern Ontario started in the early 1900's and has been continuous since that time. Some of the major operators were companies such as Mcintyre, Hollinger, Dome, Pamour, Paymaster and the list goes on. An underground survey would reveal hundreds of miles of drifts and raises. The main group of mines extends from South East of Timmins to the Pamour Mine, 15 miles to the east. During the lean years of the sixties when gold prices were low, labour costs were rising rapidly, and ore grades were dropping, many of the area mines closed down their operations."

Jan 1, 1981

By P. Hickey

"The object of this paper is to describe how the Iron Ore Company of Canada develops its management personnel. It will elaborate on the practical application of Supervisory Training and Management Development.Why are Supervisory Training and Management Development important? The answer has been the subject of many textbooks. Dr. Ken Blanchard, author and consultant, addressed this issue concisely when he said that effective managers and organizations must do two things, ""get results and develop people"". lPeople development at IOC is best illustrated through its supervisory training and management development programs. For the past twenty-five years IOC has been recognized as an industry leader in the training field. Periodic studies have played their role in establishing and maintaining this distinction. For example, in 1974, the company decided to review and up-date all its training programs. At this time, it established its own Task Force on Training and this resulted in the development of many of our present programs. Today, Supervisory Training (i.e. for first and second level management) at the Carol Project in the Labrador City area consists of various programs including: New Foreman Induction, Foreman Entrance School, Basic Management Skills, Management II, and Effective Presentations."

Jan 1, 1983

By Derek J. Cyr

Climate has an immense impact on the properties of Athabasca oil sands and the ease or difficulty with which it is excavated and extracted. During the winter months, exposed oil sands surfaces freeze. When hydraulic and electric shovels used in the various operations in the Fort McMurray area excavate the benches, large frozen lumps are created. These lumps are either destined for a lump dump where increased costs are incurred due to rehandle, or they are sent to the primary crushers where they can cause significant downtimes by jamming the crusher. The crusher down time can sometimes be in the order of hours of lost production. Studies on data from two consecutive winters at Syncrude Canada?s North Mine show a high correlation between climate and the generation of frozen oil sands lumps. Temperature, ground cover, traffic, bench exposure time, oil sands grade and moisture content all contribute to this problem. A 1D frost penetration model was used to predict the depth of frost expected in oil sands and the corresponding likelihood of frozen oil sands lumps. To combat the challenge of frozen lump generation, a number of proactive and reactive measures can be taken: artificial snow, shallow ponds, scheduling, blasting or ripping.

May 1, 2004

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

By J. A. Meech, R. J. Tucker

"A dynamic computer model has been developed to simulate the operation of ore crushing plants. The model was created in a general form to allow imitation of a wide variety of secondary crushing circuits with only minor program modifications. The system can be run on either a microcomputer or a large time-sharing main frame computer as required.The size reduction and separation characteristics of crushers and screens are based on standard manufacturers' design and performance data. These calculations are isolated within various subroutines to facilitate tailoring of the model to emulate any particular plant of interest. Input and output data are presented in a variety of formats. Crusher, screen and conveyor amperages and surge bin levels can be presented in a tabular form along with appropriate alarms arising from improper circuit operation or process interruptions. Graphical representation of the circuit together with strip chart data output are features of the system when operated in a microcomputer environment.The program is currently being used at Queen's University as a teaching aid to demonstrate plant operating characteristics, control strategies and design concepts. The acceptance of, and reaction to the program at this level indicates a good potential for it to provide a valuable tool for operator training."

Jan 1, 1985

By A. M. Childs, R. F. Mather, K. R. Rawling

"The challenges encountered in the design and construction of mines and their process facilities today are becoming more intense and the engineering more competitive. The need to incorporate new techno1ogy to compensate for ever rising costs is always present, but its application in the harsh environment of Northern Canada increasingly requires the inclusion of new proven methods and innovative approaches to arrive at economically attractive projects.This paper deals with the development of the process design for the Cullaton Lake Gold Mine in the Northwest Territories. Particular emphasis is given to the interaction of the imposed construction and testwork schedules, and their effect on certain process decisions.The challenge that faced the project team may be defined by the following factors:1. A schedule which required that metallurgical testing, engineering, and procurement and delivery of all equipment and construction supplies should be complete within a period of ten months.2. Transportation of all personnel, equipment and supplies to the site by airlift, as no road was available or affordable.3. A six week period when transportation to the site was impossible.4. The extremes of temperature beyond the tree line in the Northwest Territories.5. A complete lack of infrastructure in the area."

Jan 1, 1983

By Kallioinen Jouko

"Advanced Flotation Technology is the application driven design of Don-Oliver flotation cells to achieve the optimum performance for each type and grind of flotation. Optimum performance is the combination of both recovery and selectivity.Optimized performance is the combined product of optimized mixing and effective froth removal. Optimized mixing is applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Effective mixing for fine material is easy, but overmixing reduces selectivity in frothbed.Selectivity in flotation is an important target, especially when treating complex ores, and parameters in frothbed have been examined to improve the separation of minerals and eliminate circumstances that reduce separation rate.Advances in process control have been achieved with expert controls and instructive operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed to be used in future process development work. Excellent results of this Advanced Flotation Technology have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified."

Jan 1, 2000

By J. Shang, P. Howarth, B. Morris

Tailings from the nickel refinery in Copper Cliff, Ontario, consist of fine silicates mixed with a variable amount of conductive and magnetic minerals mainly associated with sulphides and iron oxides. Subsequent oxidation of sulphide- rich phases within the tailings results in the formation of an acidic leachate that may contain significant concentrations of trace metals. Mapping the spatial distribution of regions of higher sulphide concentration therefore provides insight into the distribution of the acidgenerating potential within the tailings. Electrical conductivity is constrained by two parameters — the concentration of metallic sulphides and the ionic concentration of acid in groundwater. Magnetic susceptibility is directly related to the pyrrhotite and magnetite content. It is proposed that combining information derived from airborne electromagnetic and magnetic surveys can provide an indication of metallic sulphide distribution. Preliminary investigations of airborne electromagnetic and magnetic data acquired concurrently over the sulphide-rich Copper Cliff tailings site reveal that these parameters can provide information on mine tailing extent and permit separation of tailings with varying compositional and alteration levels. Airborne geophysical data provide information about the subsurface while a digital elevation model (DEM) and hyperspectral imagery record surface conditions. Integration of the two data sets can reduce ambiguity when interpreting mine tailing distributions and their subsequent alterations.

Jan 1, 2001

By B. St. Pierre

"The alchemists' symbol for antimony is a diamond with a dot in the centre. The latin name ''stibium'' gives this mineral its chemical symbol ""Sb"" and the name to the principal ore containing antimony. This is Stibnite, a sulphide of antimony, and the valuable mineral at the Consolidated Durham operations. Stibnite chemically pure contains 71.69% antimony metal.Antimony is used in many forms, as an alloy in the production of metal products and as chemical compounds of oxides and sulphides. In Biblical times, antimony was used as a medicine and as eyebrow makeup.Today, the largest single use of the metal is as a hardener and strengthener of lead, and corrosion inhibitor in storage batteries. New applications for antimony in its oxide form as fire retardants are broadening the overall demand especially in the chemical, plastic and fabric industries. Other users include the Military for such things as tracer bullets, shrapnel, smoke screens and flame throwers. An unusual property of the metal is that it contracts when heated which has made it a valuable alloying metal in the printing industry, for heat shields on re-entry vehicles used in the space programmes, and also for the manufacture of bearings."

Jan 1, 1977

By Rayleen Riske

Why do we look for better reconciliation when times get tough? Why wait? Mine reconciliation should be a priority throughout the good times too. In fact, with good reconciliation, those good times are going to be even better and will help pave the way to success through those preventable bad times. Reconciliation throughout the entire mining value chain requires the capture, validation, and analysis of copious amounts of data. This task can be daunting for a team in a small mine, let alone reconciling across a suite of large mines. This paper will outline the different ways we can reconcile across the value chain, why we should reconcile over differing periods of time and how Snowden?s solution to proving reconciliation can be a simpler, reliable and transparent process. Snowden?s Reconcilor is proving to be a valuable tool on any mining scale, by capturing, validating, sorting and reporting data for timely decision making by the site geologist through to corporate management. By instigating vigorous reconciliation, you are setting your mine up for the future. Not only will you have the means to analyse your current processes and measures, but you will have the opportunity to identify and improve your mine?s performance from the resource model through to the final product.

May 1, 2010

By G. Lyle

Since its inception CEMI (Centre for Excellence in Mining Innovation) has focused on facilitating innovative solutions to the mining industry in six strategic research areas; GeoRisk, ConstructMine, ValueMine, FindMine, SustainMine and MineTech (visit www.miningexcellence.ca for details). This paper focuses on CEMI?s largest project to date, Ventilation on Demand (VOD). Energy consumption in mines can account for upwards of 40% of a mines operating cost, with a significant portion of this been consumed by the ventilation requirements. VOD provides a significant opportunity to reduce overall mine ventilation requirements and subsequently energy costs, while potentially increasing mine productivity. CEMI is currently in year 2 of an assessment of VOD, focusing on the financial, physical and equipment viability of utilizing such systems in both new and existing mines. This two year program, to be completed by March 31, 2011, is designed to systematically assess such a system to determine if and when it could effectively be applied in underground mines. The paper will describe the process by which the project was initiated, the demonstration projects established to capture data, the means to interpret the data and the modelling developed to calibrate and predict ventilation system requirements.

Oct 1, 2010

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987