Search Documents

By T. Miura, Y. Mori, H. Aoki

In a flash smelting furnace, easily combustible concentrate particles excessively oxidized and melt. The excessively oxidized molten particles then collide with less oxidized solid ones to create uniform oxidized molten particles. This collision phenomenon plays a very important role in achieving high smelting performance. The authors developed a mathematical model describing above combustion phenomena. This model incorporated fluid flow, heat and mass transfer, chemical reactions and collisions of concentrate particles. Both gas flow and particle motion were calculated using the Eulerian method. Copper concentrate was assumed to consist of chalcopyrite(CuFeS2). Considered in the concentrate reactions were the decomposition of CuFeS2, and the oxidation of the resulting sulfur(S) and pyrrhotite(FeS) to produce magnetite(Fe30 4) and sulfur dioxide(S02). Moreover a reaction due to concentrate particle collisions, in which Fe304 in the excessively oxidized molten particle reacts with FeS in the less oxidized particle, was also considered. The particle collisions were assumed to occur according to a collision probability rule obtained by computational experiments. Particle growth in diameter was described as a change in the volume fractions of particle phases. When applied to a commercial flash smelting furnace, this model reproduced the particle growth and component transfer as observed in the actual furnace.

Jan 1, 2007

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By E. G. Leonardon

The question of geophysical prospecting is one that is beginning to occupy a pre-eminent place in the minds of those actively concerned in the discovery and exploitation of ore deposits. This is in marked contrast to the reception accorded such ideas when the Junior author, six and a half years ago, began introducing electrical prospectii1g to the mining fraternity on this continent. Happily, the mention of geophysics no longer evokes the sceptical and pitying smiles that it did in those days. A little reflection will show that modern geophysical methods are merely a logical development from pre-existing technique. In the study of geological problems, is it not logical to use all possible physical properties of matter? The study of crystal form and cleavage, the examination of thin sections of minerals by means of polarized light or ordinary light, in fact, utilize physical properties of minerals for the benefit of the geologist. These are, of course, laboratory methods, and the extension of the study of similar properties into field work was inevitable. This began with the magnetometric surveys, used as early as 1760 in New Jersey to locate iron ores. Eighty-four years later, John Locke's work in the United States resulted in pointing out relationships between the terrestrial magnetic field and main tectonic features of the earth's crust.

Jan 1, 1928

By J. H. Schloen

"One of the most important phases in Canada's relatively rapid development of its metal mining and refining industries was launched in 1928 when the directors of Noranda Mines Limited decided to establish an electrolytic copper refinery ""somewhere in Eastern Canada”. Noranda's president, J.Y. Murdoch, had already evolved the company's ""mine to market"" policy and was determined to prove the economic feasibility of refining Noranda copper in Canada. The time appeared to be ripe as buoyant business conditions continued into 1929. In addition, proven ore reserves at the Horne Mine in northwest Quebec had virtually tripled and the price of copper had reached a healthy 15 cents per pound. Letters Patent incorporating the company bearing the date February 6, 1929 had been granted by the Secretary of State in accordance with an application that specified a capital structure of $2 million divided into 20 000 shares with a value of $100 each. Noranda assumed 70% of the original investment in the proposed refinery, while the Nicholas Copper Company of New York (which later became Phelps Dodge Corporation) and British Metal Corporation Ltd. of London, England, each were responsible for 15%. Nicholas Copper Company agreed to supply the design and to supervise the construction of the refinery and British Metal Corporation would act as sales agent and market the refinery's products."

Jan 1, 1999

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A 'timber car' that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By Harry Piers

A RAPID glance over the history of The Mining Society of Nova Scotia shows that in its fifty years of service, which it is now rounding out, the Society has had an honourable career, rendered signal service to the mining industry of the Province, and helped to shape and improve legislation bearing on our mines and minerals, besicles publishing very many excellent papers and subsequent discussions thereon dealing with all subjects in its field of activity. THE GOLD MINERS? CLUB OF NOVA SCOTIA: The Society has the distinction of being generally regarded as the oldest mining fraternity in Canada ( 1). Iris the direct outgrowth or reorganization of The Gold Miners' Club of Nova Scotia, which was organized in March, 1887, at a period when the gold mining industry was very prominent in the Province. Mr. Geo. W. Stuart, who, in 1934, was the only living member of the parent association, informed me that the seventeen Charter Members of The Gold Miners' Club were John H. Anderson, Charles F. Andrews, A. B. Cox, Clarence H. Dimock, George E. Francklyn, L. W. Getchell, John E. Hardman, Alonzo A. Hayward, Major R. G. Leckie, W. L. Libbey, Edward M. McDonald, G. F. McNaughton, George A. Pyke, H. A. Sanders, C. E. Willis, Benjamin C. Wilson, and George W. Stuart. Others joined later in the same year.

Jan 1, 1937

By T. E. Warren, K. W. Bowles

"IntroductionTHE PROBLEM of producing synthetic liquid fuels from coal and other raw materials is of increasing importance in Canada as well as in the United States. This is due, to a large extent, to the continually increasing demand for gasoline and other liquid products which are now obtained solely from petroleum. The United States has reached a position where domestic supplies of crude petroleum must be augmented by imports and Canada is still a long way from self-sufficiency. In the event of war, there might well be an immediate need to find supplementary sources of liquid fuels. It is, therefore, expedient to consider alternative sources of production now -well in advance of the time when supplies of petroleum may prove inadequate to meet requirements.The purpose of the present paper is to give a short review of the history of liquid fuel production from coal, to describe briefly the research sponsored by the Federal Government on the coal hydrogenation process, and finally to evaluate the present status and future trend of the synthetic fuel industry, with special reference to necessary research work.History of the Oil-From-Coal IndustryThe history -of coal liquefaction began in 1913, in Germany, with the work of Frederick Bergius. His first approach to the subject was not deliberately planned."

Jan 1, 1952

By J. P. Dick

THIS paper is a description of the milling practice and metallurgy at the Moneta Porcupine mine, Timmins, Ontario. The results obtained with an all-cyanide circuit and later with flotation followed by cyanidation are described. The ?investigation which prompted the various changes in milling practice have also been dealt with. Moneta ore is possibly the most refractory now being milled in the Porcupine district. This is due to the ultra fine state in which the gold occurs and to its intimate association with pyrite. No doubt there is ore of similar characteristics on the neighbouring properties but it probably forms only a small portion of the tonnage being mined, whereas at Moneta the bulk of the ore requires an extremely fine grind to liberate the gold. The fineness to which an ore can be ground economically has gone far beyond what was thought to be the limit only a few years ago. Formerly, a set of standard screens was all that was required to measure the fineness to which an ore was ground. At present, the Haultain infrasizer is practically indispensable, and the nominal micron has become a familiar unit of measurement to all those dealing with the problems of fine grinding.

Jan 1, 1941

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017

By M. S. Badollet

INTRODUCTION THE DEMAND for general knowledge on asbestos fibres has increased considerably in recent years. A few publications have printed data showing some of the physical and chemical prupertie3 of asbestos, but in many cases this information is difficult to find and is seldom available when needed. During the past ten years, Johns-Manville have received many inquiries on the physical and chemical properties of asbestos fibres. Fortunately, we had some of the information in our files, and we willingly supplied the data. To help relieve this need, we have tried to present briefly in this paper some of the interesting and out-standing properties of asbestos. This information was obtained over a period of years by search of the literature and by experimental investigations. PROPERTIES OF ASBESTOS FIBRES Table I (1, 2) presents, in convenient form for easy comparison, data on the principal properties of the several varieties of commercial 'asbestos' -actinolite, amosite, anthophyllite, chrysotile, crocidolite, and tremolite. Under each variety of fibre is a brief statement describing the properties in terms of structure, mineral association, origin, etc. Some of the more important data in Table I are expanded and presented in Table II (3). SOLUBILITY OF ASBESTOS A report ( 4, 5) discussing the effects of acids and caustic on asbestos fibres was published in Germany in 1927.

Jan 1, 1951

In the present work, the effect of pH, non-ionic polyacrylamide flocculant and anionic polyphosphate on rheology and settling behaviour of colloidal TiO2 suspensions (15 ? 50 wt% solid) is investigated. Maximum particle aggregation, reflecting in the highest suspension settling rate and maximum shear yield stress was achieved at pH 7.2, the isoelectric point (iep), consistent with DLVO expectation. However, the maximum aggregation condition at the iep also resulted in the poorest suspension consolidation behaviour. Significantly enhanced consolidation was achieved for a more dispersed suspension at pH values away from the iep but at reduced settling rate. Thus, when pH alone is used to control conditions which facilitate strong interparticle attraction, a high settling behaviour which is not conducive to compact consolidation results. Improved suspension consolidation may be achieved at the iep via anionic polyphosphate addition which leads to attenuation of the strongly attractive van der Waals forces and emergence of "soft" repulsion due to weak inter-particle electro-steric forces. The weak repulsion act to lubricate particles involved in the hydrodynamic interactions which controls the compressibility of the sediment bed, allowing a compact consolidation of solids to be obtained. Alternatively, non-ionic polyacrylamide homo-polymer (Magnafloc 333) was fairly effective in flocculating titanium dioxide suspensions leading to high settling rate and acceptable pulp consolidation at the iep.

Jan 1, 2006

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By R. B. Allen, E. E. N. Smith, B. C. MacDonald

"LocationTHE MAIN PROPERTY and townsite of Eldorado Mining & Refining, Limited, Beaverlodge Operation, is on the north shore. of Beaverlodge lake, •about seven miles north of the deserted town of Goldfields on lake Athabasca, and four hundred and ninety air-miles equidistant from Prince Albert, Saskatchewan, and Edmonton, Alberta. Both Eldorado Airlines •and Canadian Pacific Airlines maintain scheduled flights from Edmonton to the 4,000-foot airstrip on the north boundary of the Company property. Bi-weekly flights are made by Saskatchewan Government Airways from Prince Albert. Men and priority freight are flown by Company aircraft direct from Edmonton. From June to-September, when the waterways .are ice-free, freight is carried by barge from the •railhead at McMurray, Alberta, down the Athabasca river to Chipewyan, and across lake Athabasca to• Bushell, the terminal on Black bay, lake Athabasca, a total distance of 265 miles.The Eldorado Operation has been connected by a 12-mile, all-weather highway to Bushell. Where the highway crosses the park-land along the Fredette river, the townsite, Uranium, is under construction to provide services to the uranium-producing district. Spur roads have been built to the Ace, Fay, Eagle, •and Martin mines of the Eldorado operation, and to the properties of Pitch-Ore Uranium Mines, Ltd., and Rix Athabasca Uranium Mines, Ltd."

Jan 1, 1954

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979

By Richard E. J. Putman

THE MINERALS INDUSTRY has always been a heavy user of energy in most of its unit operations: power in the mining, comminution, flotation and electro-winning processes; fuel in its smelting and other metallurgical processes; and, of course, fuel in the on-site generation of power and steam. Many of the techniques for using computers to perform energy management and conservation tasks have been known for some time, but they have not been widely implemented because the return on investment has hitherto been insufficient. Recent trends, however, have not only caused the dollar return to rise due to higher purchased energy costs, but the cost of the investment to fall. One trend has been the generally lower cost of computer control systems themselves, due to vendors having adopted the newer, lower-cost and more reliable electronic component technologies now becoming universally available. The second trend is the development of low-cost, but high-speed, remote multiplexing devices, which have reduced considerably the expense of bringing data from points scattered over a wide area, which is typically the case when applying energy management systems to a minerals processing plant. By taking advantage of these and related developments, computer control systems can now have a rewarding impact on plant energy management and conservation practices, and recent advances in application technology have opened up new and additional opportunities for energy cost reduction and control.

Jan 1, 1978

By J. R. Emery, D. F. Coates

"FOUR PAPERS ON CEMENTED BACKFILL were given at the Annual General Meeting of The Canadian Institute of Mining and Metallurgy in 1970:Weaver, W. S., and Luka, R., ""Laboratory Studies of Cement-Stabilized Mine Tailings"".Pasieka, A. R., Beattie, H. F., and Espley, G. H., ""Cemented Hydraulic Backill within the Falconbridge Group of Companies"".McLeod, P. C., and Schwartz, A., ""Consolidated Fill at Noranda Mines Limited (Geco Division)"".Clement, W. P., and Sokoloski, R., ""Pumping Cemented Backfill"".These four papers give the impression of a development in mining technology that has been substantially completed. Somewhat over ten years ago, The Inter-national Nickel Company of Canada, Limited and Falconbridge Nickel Mines Limited started experimenting with the addition of Portland cement to mill tailings to produce improved backfill and cheaper floors for scraping. Shortly after, the Canada Cement Company Limited (now Canada Cement Lafarge Ltd.), with full support of the two mining companies, started an extensive research program to provide the technologic-al data necessary to exploit what was obviously going to be a significant development in mining technology."

Jan 1, 1970

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012

By A. Manohar Rao

Underground mining in general and more so the coal mining is a hazardous venture as it is a struggle against nature and natural forces. The stability of roadways has a direct impact on production and productivity. The roadway stability can be strongly influenced by the direction of the drivage. The stress studies are useful to provide a frame work for understanding the influence of drivage direction on roadway conditions, and to illustrate how mapping techniques can enhance this understanding. The act of mining can concentrate and re-orient the original stresses. Whenever coal is removed, the overburden weight that it carried is transferred. Vertical stresses are similarly affected when the roof is deformed or failed. The Singareni Collieries Company Ltd., a joint Public sector undertaking of the Government of Andhra Pradesh and India is conducting coalmining operations in the Godavari Valley Coalfield and is catering to the needs of a large part of South India. With the technology update, it is looking for safe mining and to achieve higher production. As a part of this, an attempt is made to understand the stress conditions prevailing on the mine blocks by different ways and means in terms of geology, structure and tectonics of the Godavari Valley coalfield, satellite imagery studies, cleat pattern, stress measurement studies conducted in different mine blocks, and stress mapping technique.

Aug 1, 2013