Search Documents

By A. Paulin, J. Roth, S. Spaic

This experiment was carried out to see whether copper-iron ingots from Late Bronze Age hoards could have been produced by smelting ferruginous copper ores. Since ferruginous copper-ores are chalcopyritic, chalcopyritic concentrate from a present day copper mine was dead roasted in our experiment in lieu of a rich chalcopyritic ore. Charcoal was used as a reducing agent in the reduction of calcine (i.e., a product of dead-roasting), and quartz sand was used as a flux. Two separate metallic solutions, a copper-base and an iron-base alloy, were obtained as a result of two factors: the presence of carbon and the miscibility gap in the Cu-Fe-C system. The metallic melts appeared in a form of bigger or smaller droplets, enclosed by a molten slag which, during the cooling, solidified into metallic beads. The presence of both metals was noticed in the majority of the examined beads. It was therefore concluded that calcine consisted of an intimate mixture of oxides of both metals which were simultaneously reduced during the reduction process. Due to the miscibility gap in the Cu-Fe-C system, separate iron and copper regions were formed in the beads. In both regions, sulphide inclusions were found. The formed molten copper and molten iron solution were found to be saturated solutions. The metallographic analysis revealed the precipitation of iron out of copper and that of copper out of iron during the cooling and solidification of melts. The formed slag contained little iron and no copper oxide.

Jan 1, 2001

By G. Grassmück

The question of whether the air curtain principle could be used under conditions prevailing in Canadian metal mines was investigated. A vertical, portable BERRY air curtain was tested, at first in a wind tunnel built at Ecole Polytechnique at full scale (8-by 8-ft cross section) to simulate a drift and its lateral connections, and then in the haulage ways of a metal mine under actual conditions. The results permit us to predict under what conditions this type of air curtain is capable of acting as an air stopping or flow regulator and how it could be further developed.

Jan 1, 1969

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By A. Allaire

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By C. -S. Xie, J. -H. Kong

The microstructure and mechanical properties of X80 hot-rolled thick steel strips with a thickness of 17.5mm produced in Wuhan Iron & Steel Company (WISCO) are introduced in the paper. The steel strips as fabricated through proper thermomechanical processing (TMP)/ on-line accelerated cooling (OLAC) processing have shown high strength and toughness, low brittle transition temperature, good weldability, and high Shear Area (SA) percentage in Drop Weight Tear Test (DWTT). The microstructure of the steel strips is characterized with mainly acicular ferrite, and fine dispersed Martensitc-Austenite (M-A) phases. It is determined that the mechanical properties are improved due to the presence of the fine M-A phases and precipitates, which could be formed by reducing the finish rolling and coiling temperatures.

Jan 1, 2005

By R. A. Nemchek

ABSTRACT Concentrator plant design has evolved from large numbers of small grinding mills to small numbers of large mills. Consequently, plant performance often hinges on the productivity of a single large semi-autogenous grinding mill. Industry attempts to address the grinding mills’ critical nature frequently result in specifications that can be made simpler, more economical, and better focused on the project’s goals. This paper surveys current specification writing practices and proposes an improved approach recognizing that product design, procurement, manufacturing, and quality are interrelated in a successful project. The lessons learned here can apply to all types of machinery specifications.

Jan 1, 2014

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By Hans Lundberg

Introduction Today, geophysical exploration is recognized as a special science wedged between geology and mining. Universities and technical institutes have special professors teaching geophysics applied to oil and ore prospecting. The list of literature on geophysical exploration has grown from practically nothing at all some twenty-five years ago to ~ several thousands of books, some of them very imposing volumes. Most of the methods now used have been developed since the first World War, and very large systematic exploration campaigns have been carried out in many places, in many countries. It has been rather difficult to obtain enough information as to what is going on in Canada. However, since the Associate Committee on Geodesy and Geophysics of the National Research Council became more actively engaged in promoting geophysical research, it may be easier to obtain information and, in the future, the quarterly issued Canadian Geophysical Bulletin may throw considerable light on the current geophysical activities in Canada. Some twenty crews have been engaged the last few years in geophysical prospecting for ore. In the United States, between 500 and 600 crews are employed exclusively in geophysical prospecting. Most of these, however, are engaged in oil exploration. During the winter 1942-1943, the German Government employed some fifty crews on geophysical exploration, and some ten crews were working for private enterprises.

Jan 1, 1948

By C. H. Hopper

DIAMOND drills have played an important part in the development of mines for many years. Recently. they have also entered the production field arid the use of diamond drills m the primary breaking of ores has become a big branch of the industry. The writer has estimated roughly that the total diamond drilling in Canada during 1942 was 5,625,000 feet, of which 2,250,000 feet, or 40 per cent, was for blast-holes. This accounts for 6,750,000 tons of ore broken, using the conservative factor of 3 tons per foot of hole. Many consider that the use of diamond drills for blast-holes is the most important advance in mine practice of the past decade, and the industry owes a great deal to the staff of Noranda Mines, Limited, for the pioneering they have done in the development of long-hole mining methods and for publishing their results. A great many mines have followed Noranda's lead. At the Waite-Amulet, Aldermac, Flin Flon, Canadian Malartic, Hoyle, and Matachewan Consolidated mines, most of the ore is broken by long-hole blasting. While the mines were developing new methods, the diamond-drill industry was developing mechanically-set bits and better machines. Through the effective use o smaller, cheaper diamonds, as well as more efficient setting, bit costs per foot are only one-half what they were ten years ago. Few people realize that a diamond bit is relatively inexpensive. The common EXT coring bit, for example, contains some 200 small diamonds, weighing altogether about 2.70 carats which, at $3.40 per carat, cost $9.20. After use, the equivalent of about 100 of these diamonds may be recovered. Therefore the true cost of the bit is only $7.00, made up of $4.60, the cost of the diamonds lost, $2.00 for setting, and $0.40 tax. The trend in machines has been toward specialization for the different classes of rock in blast-hole work. Light, high-speed machines have been developed for soft ores and higher powered machines for hard ores.

Jan 1, 1943

By Sydney C. Mifflen

COAL MINING, with its some 15,000 employees, is directly responsible for the livelihood of one-fifth of the population of the Province of Nova Scotia and indirectly so for that of possibly another fifth. Deposits of coal are known and worked in four counties of the Province, from which is being produced yearly tonnages as noted below: Cumberland County 750,000 tons Piccou County 400,000 tons Inverness County 100,000 tons Cape Breton County 5,250,000 tons TOTAL FOR NOVA SCOTIA 6,500,000 tons Production in Cape Breton county is entirely from the one source, the Sydney coalfield, and not only is this field the most important in respect to output, as is disclosed above, but it is also the largest presently known deposit in the Province and holds the greatest tonnage yet in reserve for future mining. In the light of the above more or less generally known facts, it is trite to remark on the importance of the Sydney coalfield in the internal economy of the Province. On the other hand, not nearly as well-known nor as frankly recognized is its significance in the national life of Canada, for from this field is produced not only 80 per cent of the Nova Scotia coal but over 40 per cent of all coal mined in the Dominion. Another noteworthy comparison can be made from the fact that the Sydney field contributes 22 per cent of all the bituminous coal consumed in Canada, the remainder being made up of 7 per cent mined elsewhere in Nova Scotia, 27 per cent from other parts of Canada (British Columbia and Alberta, principally), while the remaining 44 per cent is imported, practically wholly, from the United States of America.

Jan 1, 1941

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By D. R. Jolley

"The selection of equipment for open-pit mining is an important decision which results in a considerable capital expenditure by the operator. The decision is complicated by the wide product range on the market. Certainly, equipment performance is an important criterion to consider in making the decision. Equally important, however, is the operating inter-relationship among the equipment. A poor balance increases production costs and waiting time as queues form at the bottlenecks. This inter-relationship is dependent on equipment performance, but it is also affected by management decisions (i.e. scheduling techniques).The purpose of this paper is to show how the computer is used to decide which equipment and operating decisions achieve the required production objectives at least cost. Actual mining of the pit is simulated over a period of time using different equipment and scheduling decisions. Production, waiting time and costs are evaluated for each alternative until the operator is satisfied that he has achieved the best result."

Jan 1, 1970

The Bluebell mine of The Consolidated Mining and Smelting Company of Canada Limited extends under Kootenay lake, in southern British Columbia, and water control underground has always been a major problem. This paper gives a brief history of the operation, and then de-scribes the methods used by Cominco to keep the combination of lake seepage, ground water and thermal spring water under control. The pumping arrangements are de-scribed in considerable detail, with illustrations to show the various stages of development, and the power supply sys-tem is outlined.

Jan 1, 1966

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By van der Meer. F. P.

High Pressure Grinding Roll (?HPGR?) technology is applied in a broadening range of minerals processing applications for relatively wet or moist materials. HPGR grinding of dry material or involving drying and air classification is more common, for example in cement manufacturing. A number of minerals processing plants are also operating with dry material, either due to process reasons, such as considerations of preceding or subsequent process stages, or as dictated by local conditions of arid areas and scarcity of water. The present world-wide expectation of decreasing availability of water supply urges us to look for alternatives that minimize water consumption. Recently established and envisaged future HPGR applications with dry ores have indicated that the technology of dry crushing and classification as practiced in cement and limestone grinding can be applied in minerals processing. Moreover, dry technology could very well be applied for generating a final fine product at sizes near or below 100 microns, as may be required for beneficiation by, for instance, flotation, magnetic separation or tank leaching. Dry HPGR grinding requires special attention in maintaining suitable process economics, when considering power input in grinding, drying and classification. In some cases, HPGR capacity and roll surface wear life may be negatively affected by a lack of moisture in the feed. This publication summarizes some of the features of, and experiences in dry HPGR applications. This includes design aspects of the classification system and discussion of the wear protection of the roll surfaces. The paper also includes examples of operational experiences of dry practices in minerals processing and cement plants.

Jan 1, 2012

By John D. Carr

Introduction The Flin Flon zinc plant operates on what is known as the low density or standard sulphate process, that is, the zinc is carried through the plant solution circuit attached to the SO4 or sulphate radical at a concentration not exceeding 175 grams per litre zinc. The process may be described briefly as follows: The zinc is received in the zinc concentrate chemically combined with sulphur and mixed with many other impurities. The concentrate is roasted and most of the sulphur is burned to a gas, which is discharged from the plant. The roasted concentrate, or calcine as it is called, is leached with a weak sulphuric acid solution so that the resulting leach solution contains a high zinc content but a very small proportion of the impurities. The solution is separated from the solids and is purified further by agitation with zinc dust to remove copper, cadmium, and cobalt. This purified zinc sulphate solution is then pumped to the electrolytic department. The solids from the first leach are again leached, but this time with a stronger acid solution to dissolve all of the remaining zinc which is soluble in the strength of acid available. The solids and solution from the leach are then separated. The solids are stock-piled for further treatment at some future date and the solution, carrying a relatively high amount of impurities, is sent to the first leach, where the chemical action is such that the contained impurities are precipitated as solids. The electrolytic department is nothing more than a large number of electroplating cells in which the zinc is plated on aluminium sheets. Since zinc does not plate tightly to aluminium, the zinc plating or sheet is easily stripped from the aluminium and the sheets are collected to be melted and cast into the standard market bars or slabs. In the electro-deposition cells, the zinc sulphate (ZnS04) is split to metallic zinc (Zn) which plates out, and sulphate (S04) which combines with the hydrogen of the water of the solution to form sulphuric acid (H2S04). When one pound of zinc is deposited, about one and one-half pounds of sulphuric acid are formed. This acid is sent to the leaching section, where it dissolves one pound of zinc from the calcine. The solution is purified and is again pumped to the plating cells. The solution travel forms a complete circuit.

Jan 1, 1935

By William M. (Bill) Shaver

"The author will review the early history of shaft sinking as well as focus on the improvements made in shaft design and construction over the last fifty years (1970 to 2019) to predict how shaft sinking will change over the next fifty years and describe what the shaft sinking world might look like in 2070. INTRODUCTION It is a great honour to be one of your keynote speakers for the Fourth International Conference on Shaft Design and Construction being held in Toronto in November 2019. This is one of the opportunities we have to thank the Mining Companies of the world as well as the industries and companies we serve for their support of the mining contracting and shaft sinking business of Canada and the world at large. Many of these companies are represented here today. Without your support many of the innovations we will talk about today would not be possible. We would also like to thank all the companies that work with us in our business including all the contractors and suppliers who provide the various services we require. These include equipment manufacturers, engineering companies, project management companies and suppliers large and small who cater to our every need as quickly as possible. Without all these partners we would not be as good as we are. Many of these companies are our sponsors this week. Thank you from all of us! This is also an appropriate time to pause and think about those Shaft Sinkers we have lost and those who have been injured on our projects around the world. Please bow your head and remember the Shaft Sinkers you have worked with, who did not return home or those who returned home injured. Think about how we can continue the work of making shafts safer every day as we go forward with our projects so everyone goes home to their families safe and sound. Pause for a minute and thank you. The subject matter we have chosen to discuss today is “Shaft Sinking in the Next Five Decades”. How will the work be done, how fast will it be done, what will it cost, and why we think this may occur? It is appropriate to consider this over the next few days with this auspicious group we have assembled. Today, we will look back at all the advances that have been made over the last many years and look ahead to the future to attempt to predict what shaft sinking will look like in 2070. When I look around the room I recognize that many of us will not be around then so we need not worry about being wrong. Suffice it to say that the next 50 years will be very interesting and exciting for the shaft sinking business."

Jan 1, 2019

By F. Rivard, M. G. Drouet, W. S. Ruff, P. Carabin

"In both the hot rotary-salt-furnace (RSF) treatment of aluminum dross and the cold ball-millsieving (BMS) treatment of zinc dross, enormous amounts of energy and recoverable metal are wasted and large amounts of greenhouse gas are produced. Such wastes and the environment pollution could be avoided by using the DROSRITE PLUS™ technology. Economic and GHG production comparisons between the presently used industrial treatment processes and DROSRITE PLUS™, supported by over one hundred tests conducted in Canada, the US and Europe, are presented. The savings, with DROSRITE PLUS™, would be about $191 and $418 per MT of aluminum and zinc dross, respectively.INTRODUCTIONDross is a material, which forms on the surface of molten non-ferrous metal, such as aluminum or zinc, during melting, metal holding and handling operations when the molten metal is in contact with a reactive atmosphere. Dross normally consists of metal oxides entraining a considerable quantity of molten free (unreacted) metal, and for economic reasons it is desirable to extract the free metal before discarding the residue. In the case of aluminum dross, recovery of the metal is usually carried out by treating the dross in a furnace at a high temperature (Peterson et al., 2002). By contrast, cold zinc dross is crushed in a ball mill followed by sieving to separate the coarse metal portion from the fine oxide residue.The conventional aluminum dross treatment process, using gas or oil-heated rotary salt furnaces (RSF), is thermally inefficient and environmentally unacceptable because of the salt slag and CO2 produced from the combustion of fossil fuels. In the past several years, a number of salt-free processes have been developed and some of these have found limited commercial use (Gripenberg et al., 1994; Lavoie et al., 1990). In all these dross treatment processes, heating of the cold dross in a rotary furnace requires an external energy input that varies between 375 and 2,500 kWh per (metric) tonne of dross. Molten metal separated during processing of the heated dross is tapped, and the remaining solid residue is discharged from the furnace."

Jan 1, 2012

By J. R. Gordon

I-Introduction The possibility of adapting low-temperature reduction methods to the treatment of iron ores has been suggested on numerous occasions. Papers published on the subject include, notably, Bulletin 270 of the United States Bureau of Mines on The Production of Sponge Iron, the Symposium of the American Electrochemical Society (1927) on The Gaseous Reduction of Ores and Other Metallic Compounds, and Les Procédés Actuels de Traitement Direct du Minerai de Fer, by A. Mayer (Revue de l'Industrie Minerale, Nov. 15th, 1932) (1). The present paper contains the results of an investigation of the reducibility of some Ontario ores. The concentration of these ores and of the products of reduction has also been investigated.

Jan 1, 1933