Search Documents

By T. A. Utigard

To improve recoveries of Ni, Cu and Co in the Inco flash furnace, a new operating concept was investigated. By adding sufficient coke to form a supernatant coke layer, a reducing barrier would form allowing for improved reduction of descending oxidized sulfide mineral particles formed in the flame. The objective of this investigation was to study the kinetic mechanism and efficiency of the coke layer to produce a sulfur deficient matte. The mechanism and rate of carbon reduction of each of the phases formed in the flash flame, i.e. sulfides and oxysulfides were investigated by means of X-ray visualization tests. Graphite-slag reduction was also conducted for comparison purposes. In the case of slag, poor wettability and the formation of a gas film on the surface of the carbon reductant are often blamed for limiting the reaction surface area that ultimately results in poor reaction kinetics. The X-ray visualization tests confirmed that matte and oxysulfide wet coke better than slag and that the rates of reduction of matte and oxysulfide are faster than that of slag.

Jan 1, 2005

By F. O. Verret

Several grindability tests were developed over the years to design grinding circuits or optimize existing operations. Each test has its own strengths and weaknesses and it is imperative to select the proper test procedure(s) to meet project deliverables and minimize the risk of a project. Pilot plant testing of large bulk samples historically constituted the traditional approach for AG or SAG design, but was gradually replaced by small-scale tests. Nowadays, conducting grindability tests requiring only a few kilos of material on several samples is a more typical approach to grinding mill design. This paper summarises the requirements and deliverables of various bench-scale test procedures, their strengths and weaknesses, and cases where AG/SAG pilot testing should still be performed.

Jan 1, 2012

By M. L. Joy

The heat pipe is a self-contained, passive structure that uses a liquid-vapour fluid cycle to provide high thermal conductance . Through the proper selection of working fluids and container materials, heat pipes have been operated at temperatures ranging from less than -300°F to more than 3,000 °F. The passive nature, high efficiency and configuration flexibility of the heat pipe are presented. The application of McDonnell Douglas Astronautics Company Cryo-Anchor® heat pipes for foundation and support stabilization in permafrost regions is discussed. Using the proven Cryo-Anchor technology base. a proposed application of heat pipes in a cold -region mine ventilation system heat recovery heat exchanger is presented. Information obtained from the development of an air-cooled heat pipe steam condenser provides the technical basis for large -scale heat pipe applications.

Jan 1, 1978

By A. R. Hekmat

Hypereutectic Al-Si alloys are used in applications that require high resistance to wear and corrosion, hardness and low coefficient of thermal expansion, To maximize the properties of these alloys, semi-solid processing can be utilized to modify the solidification structure of the primary silicon crystals as well as to reduce microsegregation and porosity, The transformation and spheroidization of primary Si crystals by shearing in the semi-solid state are not fully understood as they precipitate in the presence of other alloy phases, The objective of the present work is the determination the rheological characteristics of A390 (Al-17%Si-4,5%Cu-0.5%Mg) alloy using a Couette type (Haake RV12) viscometer and examining the microstructural evolution during continuous cooling and isothermal shear rate experiments, The effect of shear rate, solid fraction (temperature) and morphological evolution of the silicon crystals are investigated.

Jan 1, 2005

By C. S. Gibson

"MOST of the mines in the Province of Ontario in Canada are multi-level operations in steeply dipping veins; yet there is an appreciable number whose de-posits are relatively flat-lying, ranging up to 45° inclination.The veins vary in width up to several hundred feet and may or may not be branching systems. The depths of mines range from a few hundred to 8,000 feet, approximately. The primary products of the underground group are asbestos, gold, silver, cobalt, copper, nickel, iron, uranium, talc, fluorspar, gyp-sum and salt.There are a few open-pit mines. The majority are temporary in type because, as the outcrops are removed, mining is continued be-low surface. Primary products of the open pits are copper, nickel, iron, magnesium and nepheline syenite.The industry as a whole employs about 50,000 persons, approximately 60 per •cent of whom have dust-exposure occupations. The definition of a dust-exposure occupation and the requirements for •dealing with same are set forth in The Mining Act of Ontario.Results of extensive and continuing studies on the incidence and progression of silicosis have been reported periodically for years past, in annual reports of the Mines Accident Prevention Association of Ontario and in papers presented at Conferences sponsored by Mcintyre Research Foundation of Toronto, all of which have been published. The information provided therein proves the effectiveness of the means being used to prevent silicosis and allied disorders."

Jan 1, 1960

By W. G. McBride

INTRODUCTION Preparation of this article, at the request of the Committee on papers, has been undertaken in the hope that it may stir up helpful discussion and constructive criticism. The Canadian mining industry is in the dumps and there is no use trying to deny the fact; nor does it help to say that other industries are in as bad or a worse condition. Let us face the situation honestly and see just how serious it is. The entire financial and industrial world is in a state of depression. The gravity of the case is no doubt exaggerated by contrast with the wave of optimism and false prosperity which pre-ceded it. The prevailing gloom and pessimism are just as irrational as was the former super-optimism. As far as we mining engineers are concerned, the causes are quite beyond our control, and it is the effect upon our own industry which interests us most. This effect is an accumulation of mineral products with consequent depression in price to a point where profits have almost, if not quite, disappeared. Whether this accumulation of stocks is the result of over-production or under-consumption is difficult to say, but it would seem likely that there is a combination of the two. The introduction of selective flotation has brought about a large increase in the production of zinc, a moderate increase in the production of lead, and a comparatively small increase in copper. It has turned relatively small mines into great producers, as in the case of the Sullivan, revived expiring mines like La Cananea, and brought-in new ones like Flin Flon

Jan 1, 1931

By F. Habashi

The pioneer work on pressure hydrometallurgy was conducted in Russia at the end of the nineteenth, and the beginning of the twentieth centuries, by Karl Josef Bayer (1847-1904) and Vladimir Nikolyevitch Ipatieff (1867-1952), both working independently in Saint Petersburg. Bayer was studying pressure leaching while Ipatieff was studying the precipitation of metals and their compounds by hydrogen under pressure. Gradually, industrial applications took place first in the aluminium and later in the nickel industry. Today, the technology is well established in a large number of industries, such as uranium, gold, zinc, titanium, tungsten, and more recently copper.

Jan 1, 2004

By Smortchevskyk N. J.

THIS paper describes the electrical features of the locomotive now (August, 1962) under construction for Craigmont Mines. Intended for non-specialists, it avoids details of design and calculations interesting to electricians only. The paper is divided into three sections. The first deals very briefly with the mine layout and with operating conditions -existing and expected. Reference is made to economic considerations leading to the selection of the type and size of locomotive, as well as to traction diagrams and the calculations. This material is not included in the paper because of its length and because it does not represent anything new. The second section deals with engineering and economic considerations and shows, in some detail, why the A.C. system was chosen. The third section describes the basic components of the locomotive, including the voltage regulator, the rectifiers, the control arrangement and the filter, and deals with considerations affecting the selection of their rating and design. A concluding sub-section describes, very briefly, the track and trolley details and the power distribution switchgear.

Jan 1, 1963

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By A Walker

The presence of high noise levels in many industries, together with the fact that countries are becoming increasingly concerned with the health of its citizens, has contributed to the importance of the problem of hearing loss. This problem has become the focus of scientific research, law and medicine, and the object of this thesis is to present the means whereby noise may be detected, with its resulting effects and possible means of control, in mining operations. 0BJECTIONABLE noise is a particularly prevalent by-product of the mining industry, and, al-though a dangerous noise level has been recognized, it is believed that at no time now, or in the future, will it be possible to enumerate a single over-all decibel figure at which hearing impairment will oc-cur. Individual susceptibility must be recognized in any study of occupational loss of hearing aimed at the setting of standards and criteria for industrial noise control.

Jan 1, 1963

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

There are many inherent risks in creating a mine plan for a new ore zone in an underground mine; one of such risks is the redistribution of stresses that could be a cause of instability. Using numerical modelling tools, it is possible to model the planned stope extraction sequence and evaluate the influence of mining induced stresses on the stability of remnant pillars, and use this information to remedy potential setbacks. This paper demonstrates this approach through a case study of the short-term mine plan of the Lapa mine of Agnico Eagle Mines Ltd., an underground gold mining operation near Val d?Or. Three-dimensional boundary element modelling is used to compute the stresses induced by the stope extraction sequence as planned with a longitudinal retreat mining method. The proposed methodology can be generalized to other mines that require an understanding of the stress concentrations at the pre-feasibility stage of mine design.

May 1, 2009

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By Unknown

With the present-day trend of rising labour costs and a lowering of production efficiency of workmen, it has become imperative that every effort be made to use manpower to the greatest advantage and to mechanize mining as much as possible. During the past few years this trend has gained much prominence in the Porcupine camp. In view of this, the executive of the Porcupine Branch considered that the Mechanical Movement of Muck would be a very timely subject for a Symposium. Accordingly a Committee was formed, with A. K. Douglass, Mine Superintendent for Delnite Mines, Ltd., as Chairman, and the Symposium was held in the Auditorium of the McIntyre Community Building, Schumacher, on March 25th last. Papers dealing with shovel loader and mechanical scraper operation at six of the larger mines of the camp were presented and discussed, and a tabulation was prepared giving data on the machines in operation at a total of eleven mines. The papers and tabulation, reproduced below, will doubtless be of considerable interest to operators of mines in all parts of Canada.

Jan 1, 1948

By Peter A. Cain, John C. Folinsbee

"A 4-ft.-diameter shaft has been drilled to a depth of 2,790 ft. in strong, hard, basic Precambrian rocks at Lynn Lake Manitoba. This was done on the property of Sherritt Gordon Mines Limited for the purpose of ventilating and developing the ""N"" orebody, which is located approximately 4,000 ft. south of the Farley shaft.The drilling was done under contract by two drilling companies. Peter Bawden Drilling (1964) Limited drilled the initial 12:1,4-in. pilot hole to a depth of 3,000 ft. Shaft Drillers Limited of Canada then reamed the hole to 4 ft. in diameter to a depth of 2,790 ft. At this point, the reaming was stopped because of the difficulty in passing a change in direction in the line of the pilot hole. The hole was completed by driving a raise 200 ft. from the 3000 level to the bottom of the 4-ft. hole using an Alimak raise climber.Cuttings from the reaming operation were directed into the 12:1,4-in. pilot hole, where they fell to the 3000 level and were removed by a mucking machine and standard mine development cars.The elapsed time from the start of the pilot hole to the completion of the reaming operation was ten months, with an average advance of 279ft. per month. There was a two-month delay between the completion of the pilot hole and the start of the reaming operation.The 12:1,4-in. hole was drilled in an elapsed time of 45 days from the time of setting up the rig. The average advance per day was 66.8 ft.The reaming operation was done in an elapsed time of 194 days. A one-month delay required to repair damaged equipment left 163 days for the drilling and setting-up operation, for an advance per day of 17.1 ft."

Jan 1, 1966

By H. J. Oterdoom

SMS Group (SMSG) has always been concerned about safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and also SMSG contributed with its design features to a safer operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMSG wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2015

By J. A. Brusset

Introduction I am indebted for most of the information in this paper to Mr. P. S. Lea, Deputy Chief Inspector of Mines of Great Britain, and Mr. A. E. Crook, Engineering Inspector of Mines, Ministry of Fuel and Power. Other coal-mining men in Canada may be as surprised as I was to learn that there are twenty-five Diesel locomotives in service underground in British gassy coal mines. Many more are in use underground in non-gassy coal mines and in metal mines. Approval has been granted for an additional fifty flame-proof locomotives to be used in gassy mines, and these should be in operation by the end of 1946, or as soon as manufacturing facilities permit.

Jan 1, 1946

By P. Curry, H. G. Stephenson, B. Van Den Bussche

"Three Sisters Resorts Inc. currently owns a2035 acre (824 ha) parcel of land, which previously belonged to Canmore Mines Ltd. Approximately 50% of these lands, that are slated for residential, resort and recreation development, have been undermined for coal in one or more seams.Norwest Mine Services has been contracted by the developer to assess and advise them on any past mining activity that may be potentially hazardous to their development and offer solutions to how these hazards may be mitigated or avoided.The following paper deals mainly with the procedures put in place and accepted by the approval authorities, and the Staged approach to the Investigative Procedure that Norwest follows in the mining assessment and mitigation work for Three Sisters."

Jan 1, 1996

By George M. Douglas

The southeastern shores of Great Slave lake present a curious anomaly in geographical and geological exploration, in that an area so large and important, and withal so comparatively accessible, should nevertheless have remained unexplored, unmapped, and indeed almost unknown, until quite recent" times On their return from the famous journey to the mouth of the Coppermine, the band of Indians with whom he travelled led Samuel Hearne across Slave lake. He was the first white man to see that great body of water and it is rather curious that it should have been seen first from the north rather than from the south. Hearne's account of the lake is vague, and he made no attempt ?to map the part through which he travelled. About 30 years later John Franklin, on his first journey to the Arctic, crossed the lake from the mouth of the Slave river to the Yellow Knife river. Franklin's maps show all of his route in accurate detail, except that part of it which lay through Slave lake. In 1833-34, Captain, afterwards Sir George, Back made the first exploration of the eastern end of the lake. Captain Back was then on his way to the Arctic coast by way of the Great Fish river, and his Indian guides led him through Great Slave lake by the route they had followed from time immemorial. This route, partly because of its directness, and partly because of its sheltered character, lay through the great mass of islands in the middle of the lake to the Talthei narrows, and thence along the sheltered north shore with its many coves and harbours. Pere Petitot made extensive journeys in Slave lake as well as other parts of the far north.

Jan 1, 1929