Search Documents

The #3 Shaft at Brunswick Mine, Bathurst, New Brunswick, Canada, intersects a soft graphite zone just below the 3400 Level. Ground movement within this zone causes the concrete liner of the shaft to be deflected towards the shaft?s interior, affecting the steel framework of the conveyance. In some areas, the clearance between the cage and the liner has been reduced to less than 2 cm, which is a concern. An innovative surface-mounted extensometer was designed in 2008 to monitor potential movements of the shaft?s liner. Four such novel extensometers were installed in the shaft for the surveillance of a particularly critical 3.0m by 5.5m area. This article describes the approach taken to instrument the shaft, the principle of the new extensometer, as well as the performance of the instrumentation following its installation.

May 1, 2009

By François Robichaud

"The Laronde mill has been in operation since 1988. Actual milling rate ranges from 7,000 to 8,500 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails.In 1999, the carbon in pulp circuit was replaced by a Merrill-Crowe circuit in order to cope with a much higher ratio of silver/gold associated with the discovery of the Penna shaft. Marine type diatomaceous earth was used as filter aid in both clarifier pressure leaf filters and recessed pressure filter presses from 1999 to 2005. In 2005, this filter aid was gradually replaced by alpha-cellulose after several laboratory and plant filtration trials. The selected cellulose is considered to be much less sensitive to parameters such as pH and reagent concentration and have increased clarifier and filter press filtration performance. Also, since cellulose is exothermic, replacing diatomaceous earth with cellulose as filter aid in the filter presses has increased calcining and oxidation rates in the calcining ovens since cellulose is exothermic. Finally, better calcining conditions have resulted in energy and reagent savings at the arc furnaces.This paper describes how the filter aid replacement has contributed to increasing productivity and Net Smelter Return of the refinery while reducing worker’s hazards and operating cost.INTRODUCTIONAll Merrill-Crowe circuits in the world are operated with filter aids. For years, the market for precoat filter aid has been dominated by mineral filter aids such as diatomite and perlite. Flowsheet and equipment selection at the Laronde refinery were performed in the late nineties. At that time, some key parameters of the design criteria had clearly identified marine type diatomaceous earth (DE) as the most successful filter aid. Parameters such as reagent cost and availability, clarity of the filtrate solution and good historical filtration performance in other concentrators had designated DE as the best suited filter aid. Pregnant solution processed in the refinery from its start-up through 2001 was fairly stable in flow rate and reasonable in terms of impurity content (cationic and anionic compounds)."

Jan 1, 2007

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By J. Duncan Crone

"A test surface Pulse EM(PEM) survey over a plunging massive sulphide lens, located in the Snow Lake area of Manitoba, has shown that it is possible to detect the body to a depth of 300 metres. Another surface survey in the Athabasca basin of Saskatchewan, clearly outlined a large, basement graphitic zone below 450 metres of sandstone cover. Deep detection of these conductive bodies was achieved by energizing large volumes of ground with a strong transmitted EM field. Such large fields also energize all other conductors present in the exploration area. Both of the above survey results indicate that more than one conductor is present. In such cases, detailed field coverage is required for accurate interpretation, and interpretational procedures that assume simple geometrical shapes should be applied with caution. In all cases geological and geophysical information should be coordinated in detail. The first test drill hole still has a high risk of missing the deep conductive body and two or three holes should be budgeted per target.Borehole Pulse EM surveys are now routinely used to help zero in on deep conductive targets. They are also proving effective in development drilling programs by outlining the edges of conductive bodies. The results of surveys from northern Quebec illustrate how they may provide more accurate shape and tonnage estimates."

Jan 1, 1985

By C. R. Edwards, J. R. Smith

"INTRODUCTIONThe purpose of this paper is to give an overview of the ALSANDS PROJECT, with emphasis on the approach taken in the design of the Primary Extraction and Froth Treatment Plants.The Alsands Consortium (Table 1) is a Joint Venture of 9 companies formed in 1978, with its prime objective to obtain governmental approval and concomitant suitable commercial terms to build and operate a third oil sands mining and upgrading facility in the Athabasca Oil Sands Deposit.Alsands Energy Limited is the Consortium Manager.The Alsands Project will provide about 10 percent of Canada's forecast crude oil production by 1990, which will be 20,700 cubic metres per day (130,000 barrels/day) of synthetic crude oil plus 1,100 cubic metres per day (7,000 barrels/day) of liquid petroleum gases. To construct Alsands the time required by construction labour, field non-manual and engineering support personnel as well as those trades involved in project-related urban development will total approximately 100,000,000 manhours or 50,000 man years. During regular operations, 4,800 people will be employed by Alsands.Approximately $13 billion will be spent to design, construct and start up the plant by the scheduled 1988 completion date."

Jan 1, 1982

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"As part of a larger research program, a number of MEGATEM airborne electromagnetic (EM) test flights were flown over the Gallen massive sulfide deposit in northwest Québec. A particularity of this test site is that a major part of the ore body was extracted before the MEGATEM survey. Therefore one of the purposes of this study was to verify the ability of the system to detect the remaining massive sulfides below the water in the open pit. The open pit is also surrounded by a metallic fence, and a power line is present in the vicinity. A large part of the case study involved accounting for the impact of infrastructure and acidic water on the survey, which will help in the interpretation of airborne EM responses in complex exploration situations.The Gallen deposit was also previously flown with the INPUT and GEOTEM airborne EM systems before the major exploitation period. A comparison between the results from the different survey results allows estimation of the physical properties of the Gallen deposit, which is a relatively poor conductor.A new method for removing the power line signal shows amplitudes with a smaller residual associated with the emanating fields, and more compact, cleaner responses associated with induced currents. This will make it easier to identify bedrock conductors close to power lines"

Jan 1, 2007

By T. R. Ellis

The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned. Since 1981, the Securities and Exchange Commission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis. Between 1989 and 1995, all 50 states and essentially all federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers.

Mar 1, 2002

By T. R. Ellis

"The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned.Since 1981, the Securities and ExchangeCommission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis.Between 1989 and 1995, all 50 states and essentially all federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers."

Jan 1, 2002

By Catalin Florin Petre, Elahe Ghasemian Langeroudi, Abdelaaziz Azizi, Éric Proulx, Caroline Olsen, Paul Blatter, Faïçal Larachi, Claude Gagnon

"The recovery of gold from ores is often accompanied by the release of other species in the leach solution. This state of affairs leads to depleted free cyanide levels in the slurry. Therefore, separation and quantification of these cyanicides and free cyanide at different stages of the cyanidation process as well as in waste solutions is crucial to provide mitigation tools by preventing leaching of deleterious metals for environmental considerations.COREM and the research group of Prof. Larachi have been working together on the control of gold passivation and cyanicides during cyanidation for several years. Previously, a first capillary electrophoresis (CE) protocol for the speciation of sulfur and cyanicides (SCN-, Cu, Fe) during cyanidation of gold complex sulfide ores was developed and validated for assessing industrial process water.The separation of zinc cyanide complexes used to be confronted with a number of difficulties due to the weak and/or undetectable cyanocomplexes in formally available CE protocols. Moreover, according to our knowledge, no direct CE protocol exists to separate free cyanide. Therefore, a new study aimed at developing a second CE protocol for the detection and quantification of cyanide complexes of zinc and nickel as well as of free cyanide in the cyanidation process water.To achieve this goal, six common carrier electrolytes such as pyridine, trimellitic acid, 4-methylbenzylamine, sodium chromate, phthalic acid and tris base were studied, using an indirect UV detection method. The best results were obtained using sodium chromate for which all ions were successfully separated and quantified. In addition, the effect of electric field strength, injection volume, electro-osmotic flow (EOF) modifier and background electrolyte (BGE) concentration were examined, while peak height, peak area and noise were considered for optimization.As a result, the new protocol is expected to complete the initial CE protocol by detecting cyanide complexes of zinc and nickel as well as free cyanide. Moreover, analytical determination of free cyanide in the presence of weak cyanide complexes achieved by the new protocol was also compared to conventional titration using silver nitrate solution. This new CE protocol will contribute to applied research and help plants to better understand and eventually control the behaviour of cyanidation circuits."

Jan 1, 2011

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

By G. S. Dobby, J. A. Finch

"A significant development in froth flotation technology has been the emerging industrial acceptance of column flotation during the past few years. Flotation columns are being employed now in several Canadian base metal concentrators and they are being considered f or a wide range of flotation applications throughout North and South America. Since the operating principles of a column differ markedly from those of conventional flotation machines, and have been poorly understood, scale-up of columns has been difficult. This paper describes a methodology f or translating laboratory column data to industrial operation.The scale-up model utilizes kin etic data that is obtained from a series of laboratory column experiments; the laboratory column can be as short as 2 m. For modelling purposes the column is considered to consist of two zones: the collection zone, where particle recovery occurs, and the cleaning zone, a packed bubble bed generated by downward flowing wash water. Mixing conditions in the collection zone have been characterized using the results of tracer experiments on plant columns at Mines Gaspe. The same experiments demonstrated the nearly complete suppression of entrained gangue minerals that is attained in the cleaning zone. The model explicitly accounts for both the collection zone and cleaning zone recoveries and allows for the effects of bubble overloading. Results of column scale-up experiments at Gibraltar Mines are presented."

Jan 1, 1986

By Haibin Ma, Jie Song, Qingyou Han, Xiaoming Wang, Wei Vian

In the grain refinement of aluminum, Al3Ti and TiB2 particles are introduced to reduce the casting grain size down to 200 micrometer level, which makes cold working possible. The particles are brought in by the addition of Al-Ti-B type master alloys. It is generally believed that TiB2 particles are stable and nucleate a-Al grains in solidification in the presence of extra titanium than the stoichiometry of TiB2 from the dissolution of Al3Ti particle in the master alloys. Titanium in solution either form Al3Ti layers on the surface of TiB2 particles or as solute to promote the nucleation and to restrict the growth of a-Al grains. However, a consensus on a grain refinement mechanism is still to be reached due to the lack of direct observation. This paper presents finding on the TiB2/Al3Ti interfaces in an aluminum matrix. It demonstrates a strong epitaxial growth of Al3Ti on the surface of TiB2 particles, a sign of the formation of an Al3Ti layer on the surface of TiB2 particles in grain refinement practice. The Al3Ti layer has a crystal coherency with a-Al and hence offers a substrate for heterogeneous nucleation of a-Al grains.

Jan 1, 2015

By Jorgen Elbrond, Yve Lizotte

"A mathematical procedure for determining the underground mining level layout which minimizes the total costs of excavation and haulage is described. This procedure has the advantage over previous graphical procedures of being easily amenable to microcomputers. The paper demonstrates through examples how the procedure can be applied to minimizing discounted costs of level layout as well as providing the optimal location of a production shaft.IntroductionIn recent years there have been numerous publications in mining journals concerning the minimization of mine haulage costs. With the rapid escalation of energy costs during the last decade it is not surprising that several studies applying queuing theory, simulation and mathematical programming to mining related transportation problems have been successfully undertaken. Because of the increasing availability of various sizes of computers these techniques have gained considerable popularity as evidenced by the numerous commercial packages presently being marketed.The publications concerned with haulage cost minimization are generally concluded along the lines of ' ... haulage costs at production rate x will be minimized by assigning y units to location z...'. Details about the route followed and whether it guarantees a minimization of costs are seldom considered. Route data has to date been manually resolved and used for input to developed programs. It would appear that no program has been developed to date which simultaneously minimizes costs by both fleet assignment and routing network resolution.Another important factor in transportation problems is the investment cost associated with the routes; road construction costs or, in the case of underground levels, drift excavation costs. Except for special cases the transport network which minimizes haulage costs only will not provide a minimum excavation cost solution.Zarnbo(1) illustrates by graphical and mathematical procedures how central 'facilities' can be located to simultaneously minimize investment in the transport network and haulage costs. Unfortunately these procedures and others recently applied to mine haulage problems do not provide solutions to the generalized problem. Also because these procedures are geared to graphical solutions and hand computations whereby certain possibilities can be 'visually' eliminated, they can be tedious to program and present storage capacity constraints with current microcomputers."

Jan 1, 1985

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

By H. Nakano

The codeposition behavior of impurities such as Ag, Bi, Fe, Ni, Pb and Sb with Cu was investigated galvanostatically at 5-3000 A/m2 using a Pt cathode at 60 °C in acidic copper (I) chloride (cuprous chloride) solution at pH1-2 containing 1.0 mol/L of Cu+ and 4.9 mol/L of Cl-. The impurities were classified into two groups: Group I (Ag, Bi) which codeposits with Cu as a metal, and Group II (Fe, Ni, Pb, Sb) which is slightly involved in the deposited Cu in nonmetal form from the electrolyte. Silver and Bi in Group I behaved as more noble metals than Cu, and significantly codeposited with Cu, showing typical features of regular-type codeposition. When Cu was deposited dendritically, the Ag and Bi content in the deposit increased with increased duration of electrolysis as a result of decreased net current density caused by increased cathode area. The current efficiency for Cu deposition in impurity-free solution was 95-100% over 100-1000 A/m2, but it abruptly decreased at above 1000 A/m2 when the limiting current density of Cu was attained. Although Fe, Ni, Pb and Sb in Group II were involved to 0.01-0.02 mass% in the deposit, they had no influence on the current efficiency or morphology of Cu.

Jan 1, 2007

By M. Kane, B. Bissonnette, D. Hodouin

"A laboratory cell has been designed for a careful investigation of gold ore cyanidation using mathematical modelling of the process kinetics. The cell is a stirred vessel with continuous monitoring and control of pH, oxygen and free cyanide contents. Samples are automatically extracted for gold analysis. The instruments are connected to a microcomputer which records all the measured variables and calculates the reagent consumption (air or oxygen, cyanide, lime). For cyanide control a sample is automatically extracted and filtered and the solution analyzed, using a specific electrode, by a flow injection technique. The rate of gold dissolution is modelled using a kinetic model the parameters of which are calculated by a non linear least-squares technique. The parameters of an empirical model of reagent consumption are also estimated. The resulting model is used in a simulator for gold cyanidation plant design, tuning and control.INTRODUCTIONThe leaching of gold ores in a cyanide solution is the usual method for gold extraction from raw ores. This process requires long reaction times and leads to very significant consumption of cyanide. The optimization of the cyanidation plant operation is a very important aspect of gold ore processing for increasing gold recovery and decreasing operating costs. The key parameters to the improvement of gold extraction are the selection of an efficient solution chemistry, the design of the size and the arrangement of the equipment and the correct tuning of the operating variables. Automatic control strategies can then be applied to maintain industrial operations at their optimum setpoints.Two approaches can be used for optimizing design and control of cyanidation circuits, either empirical trials for improving process performances or mathematical modelling of the process kinetics for subsequent analysis, simulation and optimization. The advantages of the second approach, which is used in this study, is that it gives a systematic pattern to interpret data and reliable tools, in as much as the models are good, to improve operation performances. In order to determine the structure and the coefficients of cyanidation models, well controlled measurement and calibration procedures must be used. The purpose of the paper is to present an equipment and a test procedure for modelling the kinetics of gold ore cyanidation."

Jan 1, 1990

By E. W. Johnson

"The title of my paper is ""I 'Wonder Where The Yellow Went"". As you can readily guess, it is not related to an old-fashioned ""Pepsodent"" sales pitch! Rather, it concerns a situation which arises all too frequently in some gold milling operations, namely when actual ounces of gold production do not come up to estimated or projected ounces. The boss man scratches his head and wonders where the missing gold has gone and how it has disappeared. The problem, if one exists, is amplified if one forgets that an estimate is just that - an estimate - and not a hard fact - even though the numbers are produced by computers. And yet, from the point of view of engineering; financial and production planning and security; it is most desirable to tie together all data relating to production estimates, losses and actual production.In the course of this paper reference will be made to the term ""variance psychology"", to a few of the physical properties of gold and to the nature of its occurrence in Canadian ores, in relation to the topic under consideration. Activities which have a bearing on production estimates will be reviewed. These include: weighing, sampling, assaying, estimating residual losses and, in cyanide plants, gold precipitate production. Mention will be made of apparent, unaccounted for and unknown losses. In conclusion, I shall draw from personal experience and relate three examples of ""Where the Yellow Went''."

Jan 1, 1986

By G. Paquet, E. Godin

"Since the mid fifty's, worlwide pellet production capacity has constantly risen (Fig. 1, Ref. 1 l. There was however at that time no real incentive to decrease production costs but only to produce as many pellets as possible. State of things changed with the iron and steel market recession, starting in 1975, and is currently leading producers to improve pellet quality and to reduce fuel and power consumption.At the Port-Cartier pellet plant, the energy needed for the induration of pellets ranks first in overall operating costs. An important step was made when starting admixing coke breeze in 1980. Oil prices justified the use of coke breeze as a direct replacement in terms of dollar/ton, however, while gaining expertise in using solid fuel a significant decrease in energy consumption was observed (Fig. 2, Ref. 2).In 1985, the ""Centre de Recherches minérales"" was commissioned to undertake research work to investigate the effects of further increasing coke addition to the pellet mix. The positive results of that work led to a 1,5% coke addition plant trial during the fall of 1985. Both laboratory and industrial results are discussed in this paper."

Jan 1, 1986

By L. Chunpongtong

ABSTRACT The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By L. Chunpongtong

The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014