Search Documents

By Omero Alonso-Gonzalez, Sergio Haro-Rodriguez, Ricardo Solis-Rodriguez, Francisco Alvarado-Hernandez, Juan Antonio Gonzalez-Anaya, Héctor Rene Vega-Carrillo

"Precious metals are currently associated with refractory minerals such as telluride (Calaverite, Sylvanite, etc.) and selenium (Naumannite Ag2Se), which are difficult to dissolve through traditional methods, therefore it is necessary to perform a pretreatment (oxidative or roasting) preceding the process of leaching by cyanidation. In this preliminary work the aim was to study the use of solvent extraction to remove tellurium and selenium ions from a synthetic cyanidation effluent, with the purpose of recycling the cyanide back to the process. For the extraction of these anions, TeO32- and SeO42-, tallow trimethyl ammonium chloride (Quatarmina TPR) and hexadecyl trimethyl ammonium chloride (Amine F) were studied as extractants, using nonylphenol as a modifier in the organic phase (trimethylpentane). The results show that it is possible to recover 82% of selenium and 10% of tellurium from synthetic solutions containing either 20 mg/L Se or 20 mg/L of Te, respectively The Se or Te mole ratio to cyanide was 1:4.INTRODUCTION In relation to extraction of precious metals, the cyanidation process has been in use for over a century and despite environmental and toxicological problems it remains the most widely used and economical process available. In the late 90s, there were great efforts to recover gold and silver from refractory ores, which is difficult to do by simple cyanidation. To improve gold recovery from tellurides and selenides that occurs in some new mines, the ores are pretreated by roasting. This is one of the most effective ways of rendering refractory gold ores leachable as well as being a fast pretreatment process compared with bio-oxidation or pressure leaching (Aylmore, 2001). The most important tellurides minerals are Calaverite (AuTe2) and, Silvanite (Au, Ag)2Te4). In the case of selenides, minerals include Naumannite (Ag2Se) and Aguilarite (Ag4SeS) (Ostroumov et al., 1989). Examples of deposits containing telluride include La Bambolla Mine (Sonora, Mexico), Cripple Greek (Colorado, USA), and Kalgoorlie (Western Australia) (Aguayo et al., 1996). The main purpose of this work was to explore the feasibility of using quaternary ammonium salts such as: tallow trimethyl ammonium chloride (Quatarmina TPR) and hexadecyl trimethyl ammonium chloride (amine F) to extract tellurium and selenium anions from aqueous synthetic cyanidation effluents, so that the cyanide solution could be recycled back to leaching process. The tests were performed on synthetic solutions similar to those found in a mine: 20 mg/L Te as TeO32-, 20 mg/L Se as SeO42- and mole ratio to cyanide was 1:4. using an alkaline medium with pH ranging from 8 to 12. Two aspects are evaluated in this paper:"

Jan 1, 2017

By J. Stiksma, K. Buban, J. Oftsie, R. Kalanchey, S. Sadykov, E. McConaghy

The Kazakhmys zinc refinery in Balkhash, Kazakhstan, which employs the Dynatec Zinc Pressure Leach Process, officially launched autoclave operations on December 27, 2003. The Kazakhmys plant is the world's first greenfields zinc refinery based on Dynatec's two-stage pressure leach technology. Production of zinc was realized on February 9, 2004, when the first cathode was stripped. Currently the plant start-up is ongoing, with progression to two-stage zinc pressure leach operation and ramp-up to full design capacity continuing through 2004.

Jan 1, 2004

By Dave Rose, David G. Meadows, Mike Westendorf

"Copper Mountain’s concentrator was commissioned in May 2011. The circuit consists of a 34’ x 20’ EGL SAG mill, a Raptor 900 pebble crusher and two 24’ x 39’6” ball mills. Each mill is equipped with a 2 x 8500 HP dual pinion drive system. The plant was designed to process 1585 mtph of SAG feed. From startup, the mill struggled to meet the required production rates. Over time, a major initiative that involved blasting and fragmentation, optimization of the SAG mill in terms of discharge grates, ball size and slurry density, and operation of up to three mobile pre-crushing plants resulted in significant increases in throughput. In parallel, a number of modeling tools, including JK SimMet, were run based on plant benchmarking exercises. Samples collected at the mine site during ramp up confirmed the very competent nature of the ore with drop weight - A*b values of less than 24 being recorded on a variety of plant feeds and lithologies. After due consideration including demonstration of proof of concept, a new pre-crushing circuit incorporating an XL2000 cone crusher and associated screening equipment was designed, constructed and commissioned at the site in August 2014. This paper reviews the history of the original circuit design, the various optimization steps taken and impacts, together with the final pre-crushing circuit and net results.IntroductionThe Copper Mountain Mine is located approximately 20 km south of Princeton, British Columbia, Canada (refer to Figure 1). The region has a long history of copper mining dating back to 1923. The Copper Mountain camp occurs in the 'eastern volcanic belt' of the Nicola Group (Monger, 1989). It is an alkali copper-gold deposit in which the volcanic strata are intruded by early Jurassic dykes, sills, irregular plugs and zoned plutons (Woodsworth et al., 1992). The stratified rocks are relatively fresh with slight metamorphism in the local contact regions."

Jan 1, 2016

By M. A. Halim, V. I. Lakshmanan, Z. Jankovic

An innovative mixed-chloride process for the separation of iron from lateritic ore is described. The separation of Fe(III) from leach liquor is an important process step for the recovery of nickel and cobalt. The patented process of Process Research ORTECH Inc. uses a lixiviant containing hydrochloric acid (HCl) and magnesium chloride (MgCl2) for the leaching of lateritic ores/concentrates followed by the selective solvent extraction step of Fe(III) over other value metals such as Ni and Co. The use of MgCl2 increases the activity of the hydrogen ion in the lixiviant, which reduces the consumption of HCl in the leaching stage and enhances the formation of HFeCl4-, thereby increasing the solvent extraction efficiency of Fe(III) with ketone. The process produces high purity iron oxide (Fe2O3) and regenerates HCl by the pyrohydrolysis of the FeCl3 rich pregnant strip solution. The developed process flowsheet is in closed loop, economically attractive and environmentally friendly.

Jan 1, 2015

By A. J. Basu

Air quality in underground mining operations can fluctuate significantly during the working day, but until recently the only way to ensure a mine had sufficient air quality was to over-ventilate and, with significant delay in adjusting the volume or direction of the airflow, working conditions were tolerable but rarely ideal. Underground ventilation management systems have been considered to achieve improved energy efficiency since at least 1995 in Canada. However, Mine Ventilation Optimization, (MVO) and integrating it with Ventilation on Demand (VOD) is only becoming more of a reality in the last seven (7) years. A systems approach to MVO takes into account all the elements from the point the power is distributed into the ventilation fans through to the actual quality and quantity of fresh air to the working face. Opportunities exist throughout the system for energy savings but not all of them are cost-effective. Depending on the application, these opportunities can be easily realized by properly sizing, streamlining, maintaining and operating the ventilation system using premium mine proven energy efficient components throughout. Implementation of VOD is a key step in achieving the MVO objective. However, VOD is a concept, and it requires various tools, procedures, and strategies for cost-effective and operationally viable implementations. This paper provides a historical background in the development of VOD and provides a framework for proper and cost effective implementation. In addition, an optimized ventilation system will also allow increased airflow by reducing resistances and shock losses. This turn in would allow production target improvement, which could be an attractive objective compared to energy savings. Mine ventilation is the life support system of an underground mine, and contributes to sustainable development and corporate social responsibility goals assuring health and safety aspects of strategic planning. The proposed framework addresses implementing mine ventilation optimization integrating ventilation on demand as a vehicle for energy, health and safety improvement and overall productivity gains in the mining cycle efficiency while significantly reducing carbon footprint of a mine.

Aug 1, 2013

By C. J. Hartley

"Scandium oxide can be recovered as a by-product from process streams in a number of chemical and metallurgical plants including TiO2 sulphate pigment, Ni/Co laterite, zirconium oxychloride and uranium operations. The feed materials available for processing can be either mid or end of process streams containing many species in solution. This paper describes the strategies available to limit coextraction of elements into scandium containing streams from TiO2 pigment production and the removal of these elements to deliver high purity scandium oxide.A critical part of process development is to work within the constraints of the main process in terms of introducing new unit processes and producing minimal additional process intermediates and residues. This requires flexibility in designing flowsheets and plants to find novel process routes that avoid production of intermediates and/or the introduction of reagents that can compromise the main process operations.Bloom Energy has developed novel solvent extraction processes for the extraction and refining of scandium oxide that minimise impacts on core process streams within TiO2 pigment plants. The additional unit processes are designed to have minimal contact with pigment plant process streams to produce a concentrate that is refined to nominal 3N purity scandium oxide in a simple, small scale commercial plant."

Jan 1, 2016

By K. Lim, J. Sobil, L. Galarza Castillo, F. Tozlu

"For mining operations globally, the scale and criticality of the grinding mill drive has meant that selection of the correct mill drive technology is paramount. With so much depending on the successful implementation of the electrical drive system— safety operation, timely installation, availability, energy efficiency, minimum maintenance and extend its use as tool to assist during mill liner exchange—customers are justified in their scrutiny and slow adoption of new drive technology. From the first installation of low, fixed speed synchronous motors to the introduction of the current source and further voltage source variable frequency drive, innovations require long periods of time and mining customers willing to push the industry forward. In recent years, the variable frequency drive has been the stepping stone for a new generation of mill drive technology. In use for decades in other heavy industrial applications, the drives allow for system optimization in a myriad of ways. The most dramatic of changes is in the design of the motor. Where in the past motor design was bound by line frequency, today the designer can optimize machine size and, more importantly, eliminate the need entirely for the synchronous motor. Induction motor design has now progressed to the point where low speed operation is possible at efficiency levels nearing those of the synchronous design. Moreover, the simplicity of the squirrel cage design means that availability, reliability and spare part requirements are greatly improved. As the next step in the evolution of large pinion driven grinding mills, the low speed induction drive offers a new reliable and robust system to the market.IntroductionAs deposit grades continue to decline, new ways of processing ever greater concentrator throughputs have been required to maintain throughput efficient and profitable operations. Furthermore, the high risk nature of mining developments requires a constant search for safer, higher availability and more efficient equipment design. Limitation of downtime is a key factor in ensuring mining operations can be sustained through volatile market conditions. Often processing the entire mine throughput through just 1 or 2 lines, the crushing and grinding circuits are of particular criticality to the uptime and, thus, profitability of any mining operation."

Jan 1, 2016

By L. C. S. Dharmasiri, S. M. Shin, A. Senaputra, J. S. Sohn, K. H. Park, J. Avraamides

Reducing agents can be applied to leach metal values from natural and secondary resources such as laterite ores and deep sea manganese nodules and recycled materials such as spent batteries / catalysts which contain high-valent metal oxides of manganese, cobalt and iron. Selective leaching of some metals can be achieved by selecting conditions to control the saturated solubility and dissolution rates of metals from oxides or mixed metal/oxide matrices. The leaching results are rationalized on the basis of chemical species, Eh-pH diagrams and heterogeneous kinetic models. The role of reducing agents such as hydrogen peroxide, sulfur dioxide and iron(II) sulphate, in acid, alkali and in the presence of complexing ligands such as ammonia for the improvement of the leaching of metal oxides and metals is discussed. Previous studies on acid leaching of metals from nickel laterites, manganese nodules and spent catalysts/batteries in the absence or presence of reducing agents show that the rate controlling step involves the diffusion of protons through a thickening product layer on the particle being leached. It is shown that the leaching of nickel and cobalt from manganese nodules and zinc-carbon batteries in ammoniacal sulphur dioxide solutions also obey shrinking core kinetics.

Jan 1, 2014

"3.1. IntroductionAmong the six platinum-group elements (POE), four have identical cubic symmetry, two identical hexagonal symmetry (Table 3.1). Despite crystallographic differences, there is a clear relationship expressed in the chemistries of the POE: they tend to be mutually soluble in one another and can frequently substitute for one another in compounds with other elements. This chapter consolidates the data on phase relations of the POE and the compounds they form with elements selected for their known or potentially important mineralogical significance- As, Bi, Cu, Fe, Hg, In, Ni, Pb, S, Sb, Se, Sn and Te-together with selected data for the occurrence of POE in certain elements such as Au and Ag, and compounds such as FeS. Resources used to compile the data are those available from the chemical, mineralogical and metallurgical literature. First each element is discussed, with composition limits of solid solutions drawn from binary phase diagrams. Single element data are followed by a discussion of the relevant binary systems and a tabulation of data for binary compounds found in those systems (Table 3.2). Tables and diagrams for the ternary and quaternary systems for which information is available follow, and finally the very limited information on the solubility of POE in mineralogically important elements and compounds is presented.The chemical, mineralogical and metallurgical literature on the unary and binary systems is extensive and widely scattered in many languages and publications; fortunately, most of the data needed to compile this chapter can be found in reliable compendia. The most useful and most recent of these works is by Moffatt (1979), because it provides a ready index to all material relating to binary systems listed in previous compendia; furthermore, the Moffatt compendium will reportably be kept up to date by annual supplements."

Jan 1, 1979

By B. J. Clauzier

"The Falconbridge Limited approach to employing communication equipment is first, to determine what is required in a given situation, second, to evaluate the possible alternatives, third, to select the most suitable hardware and, fourth, to determine what modifications, if any, are required to ensure not only successful implementation but continued low-cost reliability. Two examples are examined.The first situation required remote video monitoring of an acid loadout station. Several alternatives for linking to theremote site were investigated, including hard-wired, slow-scan and microwave. A comparison of these alternatives is shown and an appraisal of the performance of the selected microwave link is presented.The second situation required direct voice contact between the two members of an underground tram crew. Alternative solutions are described and an evaluation of the selected system- SHF portable radios - is presented.ObjectivesIn general, projects must have four main objectives: (1) to improve the safety of its operations; (2) to reduce its operating and capital costs; (3) to increase the efficiency of its work force; and (4) to increase its productivity. ScopeCommunication, when used wisely, can be a good tool to achieve these objectives. Projects can be kept simple using existing technology and adapting it to a particular task. To ensure the success of the project, it was necessary: to determine the project objectives; to evaluate the possible alternatives; to select the most suitable hardware; to adapt the hardware to the application, if required; and not to provide more than is necessary.Application at FalconbridgeTo illustrate this approach, two examples of actual installations at the Sudbury Operations are presented, sulphuric acid loadout, and the Falconbridge Mine haulage system."

Jan 1, 1987

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

By C. Rodgers, E. (Ted) Warren

"LocationThe Key Lake operation of Cameco Corporation is located at latitude 57°N in northern Saskatchewan, within the southem boundary of the Athabasca formation. The nearest city is LaRonge, located 240 km to the south. Access to the mine is by all-weather road and by private airstrip.Description of OperationThe mill was designed to produce twelve million pounds of uranium oxide (U3O8) a year from a feed grade of 2.4% U3O8. Current production is fourteen million pounds from 2.0% feed.Following grinding, the uranium is leached using sulphuric acid and oxygen in autoclaves. An eight thickener counter current decantation (CCD) circuit is used to separate the uranium-bearing solution from the solid waste residue. The uranium in solution is further purified in a solvent extraction circuit. The purified uranium is then precipitated using ammonia, calcined at 840°C, and packaged in drums for shipping to refineries. There is a crystallization circuit to recover excess ammonium sulphate produced in the process, and a waste treatment circuit.HistoryUranerz Exploration and Mining discovered the Gaertner and Deilmann orebodies in 1975 and 1976, respectively. Between 1975 and 1977, Uranerz conducted laboratory studies and delineated a process for the Key Lake ore known as the ""Bonn process."" In 1977, Sherritt Gordon Mines Ltd. was retained to conduct further studies in cooperation with U ranerz. The technical feasibility of the Bonn process was generally confirmed. Howeve1~ alternative processing methods also appeared feasible, and over the period 1978-1979, a detailed research and development program was conducted to finalize the processes to be used and to provide data for design of the plant."

Jan 1, 2000

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By W. Zheng

Pipelines can develop stress corrosion cracks in either intergranular or transgranular form. Since the mid-1980s, numerous colonies of transgranular cracks have been found across Canada and many other countries in the world. While the intergranular form of cracking has been well studied in the past 40 years, the mechanisms governing SCC in near-neutral pH environment, i.e., the transgranular form of the cracking, are yet to be understood in greater depth. Over the past ten years or so, a large number of research publications have been available on this subject and this paper summarize our latest progress in understanding the mechanistic aspect of the problem. Better understanding of the role of mill scale surface and the steel metallurgy in crack initiation has been indicated in the recent literature. However, the initiation of SCC in the lab research still relies on loading conditions that are far more aggressive than those encountered in the field. Most crack growth studies in the past are also performed under very aggressive mechanical conditions, which could have prevented the observation of environment effects. However, more recent research at lower K or Delta K ranges seems to suggest a strong role of the environment. Naturally, modeling of growth should reflect the effect of the environment, steel metallurgy, and the changing mechanical properties of the pipe steel with time. For a specific steel in a given environment, the crack growth rates tended to increase with the strain rate, indicated either by the nominal applied loading frequency or by the calculated crack tip opening rate. Future research needs to address the issue of concurrent growth of multiple interacting cracks. More attention should also be given to concurrent initiation of multiple cracks in a colony, as failure is usually caused by a coalesced crack not by an individual crack. The effect of soil environment should not be limited to the chemistry of soil solution; other factors such as cathodic processes, the variation of environment with time and physical conditions of coatings should also be considered as part of the study.

Jan 1, 2005

By Andrew Artzer, Michael Moats, Jack Bender

Antimony and bismuth in copper electrorefining electrolytes can cause cathode contamination, leading to the careful control of their concentrations. This study examined the laboratory scale removal of bismuth and antimony from an electrorefining electrolyte using a solvent extraction mini-pilot plant. The ability of a proprietary phosphonic acid ester extractant (REX-2) in a commercial diluent was studied in a simulated commercial setting. Antimony and bismuth were both extracted effectively from the electrolyte (72% Bi and 70% Sb removed) and Bi was effectively stripped (92% Bi recovered) with 400 g/L sulfuric acid. A final strip solution was obtained from the SX circuit containing 0.36 g/L Bi, 0.043 g/L Sb, 1.3 g/L Cu, and 0.18 g/L As. Unfortunately, most of the extracted Sb remained in the organic phase. Following the pilot study, experiments were performed to examine the precipitation of bismuth from the aqueous strip phase and the removal of antimony loaded on to REX-2. INTRODUCTION For many years, antimony and bismuth have been some of the most problematic impurities in copper electrorefining (ER) (Bardwell & Lapee, 1933). Along with surface roughening, high concentrations of Sb and Bi can contaminate the copper cathode and precipitate at the copper grain boundaries. This drastically reduces the drawing ability of the metal (Bender & Emmerich, 2016). For these reasons, it is necessary to control Sb and Bi concentration in the cathode, which is done by controlling their concentration in the electrolyte. Conventionally, Sb and Bi concentrations are controlled by maintaining a proper As/(Sb+Bi) molar ratio in the anode and arsenic concentration in the electrolyte. Antimony and bismuth are removed during electrolyte purification using liberators (electrowinning cells) and/or ion exchange. Liberators treat an electrolyte bleed stream from the ER circuit and electrodeposit increasingly impure copper as the copper concentration of the solution decreases. Traditionally, first stage liberators reduce the copper concentration from ~45 g/L to ~15 g/L and produce saleable copper. Second stage liberators decrease the copper concentration to ~8 g/L (Biswas & Davenport, 1980) which results in contaminated cathode that is returned to anode production (Biswas & Davenport, 1980; Wang, 2004). Further electrolyte purification is not always required but third stage liberators can be used to reduce copper concentration below 2 g/L which results in significant removal of As, Sb and Bi and very impure deposits which are recycled to a smelter or used for As production. However, liberators do not have very high energy efficiency (Acharya, 2014; Ando & Tsuchida, 1997) and below 0.5 g/L copper, highly toxic arsine gas may form (Biswas & Davenport, 1980).

Jan 1, 2019

By M. Holmes, R. Molnar, E. Norton, K. Baxter, J. Riordan

The Boleo Copper-Cobalt-Zinc-Manganese Project of Baja Mining Corp. is situated adjacent to Santa Rosalia on the Baja Peninsula of Mexico. The El Boleo ore is a mixed oxide-sulfide deposit with major values in copper, cobalt, zinc and manganese. The metallurgical process designed to treat the El Boleo orebody involves a sulfuric acid leach in seawater using oxidative and then reductive leaching to maximize metal extraction. The leach solution is separated from the barren solids via counter current washing through a series of high rate thickeners. Copper is recovered using conventional SX-EW processing as cathode. Zinc and cobalt are extracted from the copper SX raffinate after iron and aluminum precipitation. The CSIRO DSX solvent system (Versatic® 10 and LIX® 63 mixture) are used in this extraction. Manganese remains in the DSX raffinate and is recovered by soda ash addition as a high quality manganese carbonate precipitate. Zinc and cobalt are acid stripped from the loaded DSX solvent. Zinc is then re-extracted away from cobalt using Cyanex® 272 extractant and stripped into a highly concentrated strip liquor (+100 g/L Zn) and directed to either a spray dryer or a granulator for production of zinc sulfate monohydrate. The zinc solvent extraction raffinate, containing cobalt, advances to another SX circuit using Cyanex® 272, for the recovery of cobalt as cobalt cathode. In this paper, the detailed results from bench and integrated pilot plant testing for zinc recovery from the El Boleo ore will be described. The results of this testing are currently being used to engineer the commercial plant at El Boleo.

Jan 1, 2008

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By Mike Dry, Mani Manimaran, Mykolas Gladkovas, Mariam Melashvili, Chris Fleming

Development of a new hydrometallurgical flowsheet requires quantitative description and optimisation of all chemical processes in each step in the process, as well as mass and energy balances across a fully integrated circuit incorporating all the unit operations. This paper covers steps leading to early modelling of a gold processing plant based on a bromine/bromide lixiviant. Research conducted at SGS Lakefield in collaboration with Albemarle provided the data that were used in the development of this model. A previous investigation in this series described the leaching behaviour of various mineral types in Stabilized Bromine reagent. This paper is concerned with the gold recovery operations associated with a conceptual bromine leaching process. The recovery of gold by different types of resin and activated carbon was studied, along with various methods of stripping the gold from the extractant. The circuit is closed by electrolysing the spent leach liquor to oxidize some of the contained bromide back to bromine that would allow recycling the regenerated leach solution back to the leach step in the process.

Jan 1, 2015

By G. M. Ritcey, B. H. Lucas

In the conventional alkaline leaching of concentrate containing nickel, copper and cobalt, copper is usually removed from the system, prior to nickel reduction, by sulphide precipitation. A new process is described for the selective extraction of copper and separation from cobalt and nickel, using liquid-liquid extraction. General Mills LIX-63 dissolved in a kerosene diluent is the extractant. Trace amounts of co-extracted cobalt and nickel are easily removed by a scrub treatment, and copper is recovered from the extract by sulphuric acid stripping, thus providing a solution amenable to the oroduction of electrolytic copper. Estimated processing costs are included together with a proposed flowsheet.

Jan 1, 1972