Search Documents

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By D. M. Muir

The mineralogy of residues formed during the pressure acid leaching of arid region nickel laterite ore varies according to the salinity of the process water, alkali cation additives and the overall acid loading. In fresh water, hematite is the main iron-bearing leach residue component, together with amorphous silica and hydronium or sodium alunite/jarosite [(H3O,Na)(Fe,Al)3(SO4)2(OH)6]. As the process water salinity increases, or as NH4+ or K salts are added, alunite/jarosite is the kinetically favoured iron-bearing phase accompanied by an increase in acid consumption. The alunite/jarosite appears as two XRD distinct phases with different Fe:Al molar ratios. In weakly saline water, iron-rich alunite/jarosite slowly transforms to hematite and an aluminium-rich alunite/jarosite together with the release of acid. The addition of potassium salts forms a more stable alunite/jarosite whilst the addition of ammonium salts leads to greater transformation of alunite/jarosite at 250°C. Weakly saline process water gives enhanced nickel recoveries, whilst strongly saline process water gives lower nickel recoveries but higher soluble iron because of chloro-complexation. SEM and microprobe analysis shows very little nickel is associated with the alunite/jarosite and hematite phases. Nickel losses to the residues are attributed to adsorption on amorphous silica and to a lesser extent on alunite/jarosite.

Jan 1, 2006

By I. H. Warren, Forward F. A

The reduction of aqueous slurries of uranyl carbonate at elevated temperature with compressed hydrogen m the presence of metal catalysts and certain organic promoters has been shown. to yield uranium dioxide. The reduction takes place in a sequence of steps. The purity and sintering properties of the dioxide make it of interest as a starting material for fuel element production. Simple control can be exercised over the surface area and oxygen/uranium ratio of the product during reduction. URANIUM dioxide for fueling atomic power reactors 1s conventionally produced as a powder by simultaneously decomposing and reducing ammonium diuranate with hydrogen in a furnace at high temperature. Fuel elements are then generally made from this powder by compacting and sintering ( 1). In order that elements approaching theoretical density may be obtained,

Jan 1, 1961

By Jie Li, Xinyu Liu, Yan Chen, Linjian Ma, Yasong Wang

Nonlinear time-dependent response analysis of salt cavern under extreme loads in disaster mode is of great importance to the safety and disaster prevention of gas storage group. Uncontrolled blowout is one of the extreme conditions for compressed-air cavern operation. Based on the geological structure of Jintan salt deposit, China, the numerical model of the complete process of water solution, cyclic operation, and internal pressure runaway was developed. The effects of rapid unloading on the stress filed, the progressive failure of surrounding rock, the volume convergence of storage cavern, and the ground subsidence were simulated employing an elasto-viscoplastic damage constitutive equation for rock salt. The results indicate that the damage and failure zones propagate much larger in the mudstone interlayer than in the host salt. The volume of damage and failure zones surrounding salt cavern induced by unloading process is 5~6 times that of cyclic injection and withdrawal process. The average volume convergence rate of salt cavern reaches 0.012%/d~0.013%/d, which is 6~6.5 times that induced by cyclic operation. The ground subsidence exhibits a typical funnel curve. The affected region of ground subsidence due to rapid unloading in the blowout period is about two times the maximum cavern diameters. Furthermore, double cavern analysis reveals that the interaction between adjacent caverns may be ignored so long as the pillar width is larger than two times the maximum cavern diameters.

Jan 1, 2015

By K. Iturralde

The article discusses the possibility of automation in refurbishment processes of social dwelling built from 1950 to 1970. These massively produced buildings were mostly designed prior to the law enforcement regarding thermal insulation or accessibility. Nowadays, many of these buildings are being retrofitted. The article focuses on the works in the external envelope. The task of renewing the whole social building stock is big and it requires a systematic process that facilitates a rapid upgrading, without neglecting the specific situation of each case. How could an automatic refurbishment process of these buildings be defined? The process should start with the data collection of the building and the creation of a 3D model using software such as BIM. The project, drafted in 3D, should facilitate the manufacture of building elements by robotics. In turn, it should be noted that during the assembly at the site, the pieces must be fixed quickly and efficiently. Is it possible to implement an automated process for the refurbishment of apartments built in the second half of the twentieth century? To approach the answer, a virtual refurbishment project is performed. The article focuses on the rehabilitation of the building envelope. Furthermore, it gives special attention to the double skin facade. It is well known that a second skin in this type of building can be an element that integrates several functions. Finally, needless to say that refurbishment of residential buildings is a need in our society. By extending its life cycle, robotic refurbishment provides more favorable socioeconomic and environmental capabilities than the sole construction of new buildings.

Aug 1, 2013

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By A. Pearson, Auld. F. A., S. O. Colbeck

"To minimise mine shaft maintenance over the long-term, some potash mine shaft sinking projects have required the provision of a continuous fully welded waterproof steel liner over a substantial depth to achieve zero water ingress. This brings many challenges, including the implementation of a bottom-up construction sequence incorporating extensive waterproof welding and how to ensure the integrity of the welded liner when subject to substantial temperature fluctuations that are likely to occur with a composite steel-concrete liner placed within an artificially frozen shaft excavation. This paper highlights the key challenges and discusses multiple mitigation measures including vertical shaft movement joints and a combined structural-thermal analysis approach. INTRODUCTION Whilst the application of combined steel and concrete shaft liners using a fully welded steel liner is not new and has been used in several previous projects, most notably at Lanigan (Storck, 1968 & Roesner, 1980), recently the need to provide a continuously welded steel waterproof liner for over 800 m length of shaft for a potash mine has been considered. The need for a fully continuous welded steel liner arises from the perceived benefits of providing a fully dry shaft environment to; increase the life expectancy of the shaft; reduce routine maintenance particularly combatting salt accretion and minimising wash down practices; and improve long-term ground stability by preventing salt dissolution. Whereas previous projects have employed discontinuous sections of steel liner, when a fully continuous liner is employed longitudinal shaft strains from thermal changes result in significant deformations that must be either explicitly accommodated or resisted. Note, these thermal vertical expansion forces are more than capable of lifting the shaft collar and head frame structures should they be fixed in place. Typically, shafts are designed to resist vertical forces (collar loads and self-weight) by creating mechanical interlock with the adjacent ground. In competent rock this occurs incrementally with the construction of the shaft liner, and occasional hitch/crib structures are constructed as intermediate foundations to guarantee the transfer of vertical forces at distinct horizons. Usually this means cribs are constructed at first rock head, above the station level, and at the sump, although sometimes additional cribs are formed when entering and exiting weak strata or when a change in shaft liner construction is required."

Jan 1, 2019

By P. H. Rodriguez

The aquatic hazard classification system of the OECD and EU requires that sparingly soluble metal substances (SSMS) be tested using the OECD Dissolution/Transformation protocol in order to quantify the release of the ecotoxicological relevant species (dissolved ions). The SSMS category contains massive forms of metals, which due to their low solubility and slow transformation characteristics are a special case. The main factors that produce the release of metal into solution are exposed surface loading, pH, and stirring rate. The classification system at present prefers the use of mass loading as opposed to surface loading, in which case the amount of metal released will primarily be a function of the pH, and mass loading. Within the framework of the European Copper Voluntary Risk Assessment, coordinated by the European Copper Institute, we have proposed and developed a methodological procedure in which we demonstrate that surface area is an intrinsic property of a SSMS and we link the exposed surface loading to the toxicity reference value in order to obtain an aquatic hazard classification for massive metals. As example, the aquatic hazard classification for copper massive will be discussed. This approach is recommended for metal massives and metal powders.

Jan 1, 2007

By Syamujulu. M

Subsequent to the unbundling of the Zambia Consolidated Copper Mines (ZCCM) and the privatization of its constituent parts, the Konkola Copper Mines (KCM) represents a third of the original conglomerate. Now run by private hands as a sub group of Vedanta Resources Plc of India, KCM is strategizing on how best to deal with the operational issues of the organisation to resolve some of the difficult, logistical, environmental, mineralogical and metallurgical problems being encountered to tum them into opportunities as the company turns around. This paper reviews the options being put in place to provide appropriate solutions and strategies including the treatment of the highly siliceous low energy copper belt concentrates in its mining operations in Zambia.

Jan 1, 2007

By Paul Guliov

Potash dominates the industrial mineral scene in Saskatchewan accounting for 44% of total provincial mineral production in 1981. More than 7 million tonnes of potash have been produced annualy in recent years; ten underground mines are presently (1983) active. Sodium sulphate and cement are also important mineral products. Construction aggregates, clay products, bentonite, salt, peat moss and sulphur complete the list of industrial mineral products.

Jan 1, 1984

By J. Robison, H. Pieterse, C. C. Smith, M. Luque, S. Chipman

Phase change during pressure let down releases significant amounts of energy that must be controlled to avoid undo wear and tear on equipment. Hydrometallurgical slurries require flow control equipment (valves and tanks) made of expensive materials to withstand the abrasive, and often corrosive nature of the slurry. Presented is a model of the nozzle of a let-down choke which is designed to control the flow pattern that exits the choke (valve) as it enters the receiving tank. This model can be used to design chokes which allow for the dissipation of the energy released during pressure let down by spreading the stream over a significant portion of the slurry pool in the receiving tank to minimize wear on equipment near the nozzle exit and the bottom of the slurry tank. An example uses the model to choose the nozzle expansion (area) ratio to select the outlet slurry velocity and slurry expansion angle.

Jan 1, 2004

By L. J. Cunningham

I THINK it can be safely said that no mining operation, whetl1er open-pit or underground, is ever entirely free of water. It follows that every ton of ore bears a charge which represents, either directly or indirectly, the cost of keeping the mine workings as dry as possible. Water problems occur in all phases of mining operations. They cause difficult and costly drilling conditions during the exploration stage, they often seriously delay mine development, they can slow mine production and reduce efficiency, and they are a continued burden over the life of the mine. It is therefore in the interest of all mining men to be familiar with the methods and materials used for grouting. The most common grouting material is cement. Cement grouting is old and well established, and many engineers are familiar with its uses and limitations. The technique of cement grouting is relatively simple and fairly well understood, and the materials utilized are relatively in-

Jan 1, 1962

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

By E. Burdukova

Rheological measurements have found a wide array of applications in mineral processing research. Rheological properties of mineral suspensions are highly dependent on the mineral surface properties as described by DLVO theory, and the relationship between these properties and inter-particle interactions is well established. In this paper, rheological properties of mineral suspensions are used to study the differences in behaviour of isotropic talc and anisotropic zirconia minerals as a function of varying properties of the suspension medium, such as pH and polymer dosage, specifically carboxymethyl cellulose (CMC). It was found that the rheological tests when carried out in parallel with electrophoretic or point of zero charge measurements, clearly reveal differences between behaviour of the suspensions of isotropic and anisotropic minerals. These differences are further accentuated with the addition of carboxymethyl cellulose (CMC).

Jan 1, 2006

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"The future of Polish copper mines KGHM Polish Miedz S.A. will be associated with mining at depth. At present, technologically advanced measures are being introduced to minimize the adverse influence of the environmental hazards on people working underground. Polkowice-Sieroszowice mine is the only mine in Poland where mining takes place in copper and salt deposits. On the basis of the current and anticipated methods of ventilation of a selected ore deposits the paper will analynze a number of solutions enabling planned mining of copper ore deposit, while minimizing the impact of natural aerological hazards in working areas. INTRODUCTION The future of copper ore mining, carried out by KGHM Polska Miedz S.A., will be based on mining from continuously greater depths (Butra, 2015). It is forecast that this will be accompanied by an increasing climatic hazard, resulting from an increase in the original temperature of rocks of more than 45°C as well as gas and geodynamic hazards (Soroko, 2015; Andrusikiewicz, 2015). Due to the safety of underground teams, a need arises to develop methods eliminating the adverse impact of the natural hazards, down to a level enabling the mining activity to be carried out on an industrial scale while maintaining favourable economic parameters. Current depths of the copper ore deposit being developed are effectively verifying the technical methods and measures employed to date for eliminating the natural aerological hazards. Amounts of air supplied to mining areas, with lengthy transport routes, are becoming insufficient for miners’ temperature safety, whereas increasing the power of cooling air-conditioning stations for cooling the air undermines the economic legitimacy. However, along with the temperature hazard, a significant problem at the current depths is an increase in gaseous occurrences in the headings’ areas. The concentrations of natural harmful gases found, even with the values below the permissible concentrations, in the case of limited amounts of air and/or low airflow rates, may pose a considerable danger to the workers. The hazards referred to are currently the major factors determining the advance of headings, above all in mining sections, being the outcome of geological structure and depth of lying of a deposit. However, at the current depths of mining minerals from deposits, room-and-pillar mining systems employed also have a decisive impact on the increase in natural aerological hazards."

Jan 1, 2019

By G. Binks

In 1997, the Zinifex Hobart Smelter ceased ocean disposal of jarosite and the flowsheet was converted to reject iron as paragoethite. This paper describes the evolution of the flowsheet since the changeover and considers future flowsheet developments. The major change to the flowsheet has been an increase in the silica content of the calcine resulting from treating increasing levels of Century concentrate. The high silica levels impacted on the paragoethite precipitation stage, causing a deterioration in the settling and filtration characteristics of the paragoethite and an increase in the contained zinc level. The implementation of a two stage neutral leach step has enabled the flowsheet to cope with the higher input silica levels. Future developments include an understanding of the form of the zinc in the paragoethite and options to lower the zinc level to improve the overall zinc recovery.

Jan 1, 2006

By Daniel Torres Espinoza, Jose Pinedo

"Ventilation is a vital service in underground mines, required to provide fresh air to the work force and dilute diesel equipment gases (CO, NOx) and diesel particulate matters (DPM). At a Mexican precious metal mine in the state of Chihuahua there is a VOD system implemented using Howden’s control and monitoring system and a state of the art tagging and tracking technology. The JM zone of the mine is ventilated using a push and pull system, using automated regulators on each level to control the air going in and out of the levels. The implementation of advanced control strategies using Howden’s VentSim™CONTROL allows the mine to generate significant savings and increase health and safety of the workers.INTRODUCTIONIn underground mines, ventilation is a requirement in order to maintain the fresh air needed for personnel and equipment. Ventilation regulations dictate the amount of air required underground to carry out day to day operations by limiting the exposure that workers have to toxic gases and other pollutants. Regulations for required airflow in underground operations for diesel pollutants are generally provided on vehicle rated brake horsepower, in Mexico the requirement is 75 cfm/bhp. In underground mines, ventilation services can account to up to 75% of the mine’s energy consumption, and it is very common for fans to operate all the time because of a lack of control infrastructure for the ventilation system. By the implementation of a Ventilation On Demand (VOD) system a mine can reduce this consumption with different control strategies. The main infrastructure required to implement this system consists of remote control of ventilation infrastructure (fans and regulators), a communication network between throughout the mine with the surface and a tracking system for personnel and diesel equipment. Software is required to determine fresh air requirements based on the tracking system data and then send the control commands to the different ventilation infrastructure. In 2015, San Julian Mine acquired Howden’s VentSim™CONTROL (formally SmartEXEC) and the hardware solution to deploy a VOD system at their operation. The VOD system and Fresnillo plc’s San Julian Mine in Chihuahua, Mexico, consists of control of 10 surface exhaust fans, 2 surface intake fans, and 12 underground automated regulators. It also includes the monitoring of 46 flow sensors, 28 CO sensors, 28 NO?? sensors and 42 temperature and humidity sensors, approximately 500 personnel tags, approximately 220 vehicle tracking tags with diesel status (ON or OFF) and approximately 250 tracking zones. This paper discusses the control strategies that have been implemented at San Julian Mine since the system was commissioned and the next steps that will be taken at the mine with the system as they test different level on VOD."

Jan 1, 2019

By A. Glover

As the demand for natural gas as a prime global energy source continues to grow, the search for new sources of the fuel spreads into geographical areas that are more remote from the marketplace. Along with this comes the need for longer and ever more efficient pipelines. This requirement for higher value in natural gas transportation is satisfied to a large extent through the application of high strength technology and innovative design approaches that support increased design and operating pressures. This paper reviews the latest accomplishments and successes in these technologies for use in gas transmission. It also explores some of the technologies which are targeted for the future to allow the industry to achieve even higher benchmarks in reliability and cost-effectiveness. The central element in the theme of high strength technology for gas pipelines is that of high strength steel. From tensile strengths of Grade 359 a few decades ago, more and more operators are now specifying Grade 550 linepipe for their large diameter projects. As well, Grade 690 steel is operating successfully in limited transmission applications and Grade 825 has recently been installed. With the introduction of the latest high strength pipe comes the need for high strength fittings. The industry's first Grade 550 fittings were recently specified and installed on a project with Grade 825 line pipe. High strength materials can only be implemented successfully if compatible design and construction processes are in place. The latest developments in strain- and reliability based design will be described as well as the corresponding advancements in welding and inspection technology.

Jan 1, 2005