Search Documents

By B P. Scott

Podsol soil horizons developed on Pleistocene glacial sediments overlying the Coronation Mine orebody were analyzed for copper and zinc spectro-photometrically, using biquinoline-isoamyl alcohol and dithizone carbon tetrachloride reagents. Copper and zinc are concentrated in the A. and C horizons, whereas the A1, A2 and B horizons are leached. Of economic significance is the fact that the C horizon contains a copper anomaly, in excess of 100 times back-ground, directly over the orebody. Due to the erratic distribution of high copper concentrations in the Ao horizon with respect to the orebody, that horizon is not considered as a reliable prospecting datum. U NDER certain conditions, metallic ore deposits are accompanied by primary halos of trace elements in unweathered rock surrounding the orebodies or by secondary halos in weathered rock, alluvium, soil, or vegetation above or near the mineralized zones. Where such halos occur, chemical analysis, as applied to the detection of trace elements, is a valuable prospecting aid, permitting the detection of mineralization of possible economic value.

Jan 1, 1965

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By G. Frithum

In the present paper a new and highly economic route for Fe-separation from HCl leaching processes in hydrometallurgical applications is described. In most ore leaching processes, Fe is involved and needs to be separated; HCl has become an interesting leaching agent, because it can be recycled. Usually a mix of Fe2+ and Fe3+ is obtained which can be hydrolyzed directly (in case only Fe3+) or roasted via pyrohydrolysis (in case of Fe2+) to ferric oxide. Economic oxidation of Fe2+ to Fe3+ is described, and potential technologies for regeneration of HCl with separation of Fe are shown and compared.

Jan 1, 2014

"The outlook for Eastern Canada is decreased coal production and for Western Canada increased production. The market for Western coal is expected to reach 40 million tons per year in metallurgical and thermal-power markets.Technical developments in Eastern Canada include successful methane drainage experiments, modifications to the shearer-loader to improve cutting rates, mechanized mining of a tail-gate stable and mechanical stowage of level brushing. In Western Canada, the most modern equipment is used in mining, beneficiating and shipping coal. Underground hydraulic experiments were started in 1969. The importance of reclamation was recognized and plans have been made to re-vegetate disturbed areas and mine dumps.The Mining Research Centre closed the field office in Nova Scotia and is preparing to open a new field office in Calgary, Alberta."

Jan 1, 1970

By R. I. Kraydenko, A. N. Dyachenko

"The possibility of SiO2 5N production by staged purification of ammonium hexafluosilicate (NH4)2SiF6 is discussed. High-purity silicon dioxide can be obtained with fluoridation of quartz concentrate by solid NH4F at 100 °C, with further sublimation of the product at 320 °C, its dissolution, ammonia hydrolysis, filtration and drying of SiO2•nH2O. This is accompanied by regeneration of the processing reagent - NH4F.INTRODUCTIONProduction of high-purity silica-5N (SiO2 content over 99.999%) is an important and urgent task of the modern chemical industry. This material is used in the manufacture of optical glass, optical fibers for internet cables, silicon for solar power and electronics.Quartz concentrate is raw material for the production of silicon dioxide. The existing technologies of synthetic silicon dioxide were introduced in the mid-twentieth century. These methods are energy-consuming, multi-step and do not meet stringent environmental requirements. In fact, as some conventional technologies became obsolete; it became necessary to develop new methods for the production of synthetic silica. We believe that the fluoride technology of processing of quartz materials by ammonium fluoride is the most promising direction.In industry, silicon dioxide marked ""Silica White"" is obtained by liquid-phase method. The method consists of the precipitation of amorphous silica from sodium silicate solutions with acids. The resulting product is filtered, washed and dried. Depending on the deposition conditions and nature of the coagulant the ""Silica White"" is acidic, neutral or alkaline. The dry product is subjected to grinding. The degree of dispersion and porosity of the particles of Silica White depends on the nature of decomposition agent (a substance that decomposes the silicate) and coagulant, conditions of sedimentation, filtration and drying. During the drying process the silica particles are sintered into aggregates of a few millimeters."

Jan 1, 2012

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011

By Paul H. Atkinson

"Sampling in the mineral processing industry has always been a subject which has received considerable discussion. There have been many volumes written on theory, techniques and practical application of sampling. However, until recently, the companies were not completely aware of the potential savings available with properly designed sampling systems both to assist in pieces: control and final product values.Definition In our discussion today, we will define sampling as the operation of removing a part, convenient in quantity for analysis, from a whole, which is of much greater hulk, and removing it in such a way that the proportion and distribution of the quality to be tested, i.e. size of particle, moisture content, specific gravity content, mineral and chemical composition, are the same in both the sample and the whole.Application It has been well established that undetected errors can result in large economic losses, thus most firms depend upon some type of sampling and sample analysis as a control in their continuous processing of materials. Despite the large investment in facilities and personnel the ""analysis"" of a sample can be no more accurate or reliable than the sample on which it is being based. The importance of sampling is recognized by a great many but it is appreciated by only a few, largely because it is sometimes one of the items which is taken for granted."

Jan 1, 1976

In this study, flotation of fine galena, chalcopyrite and pyrite was performed after grinding with different extent of oxidation-reduction condition adjusted by grinding media. Sodium dithionite and iron ions were added in mill to simulate pulp potentials and iron oxidation species produced by grinding media, respectively. The types and quantities of the metal oxidation species on mineral surfaces were determined by EDTA extractions, while the surface electrical properties of minerals and interaction of different types of metal oxidation species were studied by zeta potential measurements. It was found that the nature and concentration of the absorbed metal oxidation species were dependent on oxidation atmosphere controlled by the iron amount of grinding media. These species interacted with each other and had an important role in determining flotation of fine galena and chalcopyrite as well as activation of fine pyrite by lead and copper.

Jan 1, 2006

By L. Rosato

In the past decade, as a result of increasing iron loads, Canadian Electrolytic Zinc (CEZinc) has become a pioneer in understanding the critical factors that affect the roasting of concentrates with high pyrite contents as well as those factors governing the effects of high iron loads on the leaching circuit. De-bottlenecking efforts in the roaster and acid plant section of CEZinc have given rise to a better appreciation of the impact of iron on roaster productivity. High standards for impure solution quality, zinc recoveries and residue disposal have all led to an increased comprehension of the limits of the leaching circuit and the optimization potentials with respect to iron and ferrites. In this paper, the impact of iron on the roasting and leaching circuits of CEZinc will be reviewed and special emphasis will be given to some of the more recent process optimization and improvement activities.

Jan 1, 2006

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By Jochen Petersen, Jean-Paul Franzidis, Allan Nesbitt

This study presents a method for the determination of intra-particle diffusivities in ion-exchange resins for the purposes of evaluating the state of resin degradation during service. The method uses a zero length column (ZLC) in a closed circuit with variable speed pump and reservoir. The intra-particle diffusion is determined from absorption data by using the Nernst-Plank approximation along with the ‘mass transfer factor’ - which is a product of the mass transfer coefficient (kf )and the concentration of the adsorbing ion in the liquid at the surface of the resin - in a computer algorithm fitting simulated curves to experimental data.. Through this approach the changed intra-particle diffusivity, of a gel-type acid resin, over a 1000 loading and elution cycles, is shown.

Jan 1, 2014

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By Link. Theo A.

Introduction Since the discovery of a major oil pool at Leduc, Alberta, on February 13th, 1947, the long spell of 'oil drought' in Western Canada is now being turned into an oil and gas flood which requires immediate action to obtain the optimum economic benefits. The Woodbend, Section 9, and Okalta extensions of the Leduc field itself have been established; the Redwater pool, lying thirty-seven miles northeast of Edmonton, has been discovered and is being drilled up, and the Imperial Schoepp No. 1 or Golden Spike discovery holds promise of something phenomenal in view of the 500 feet of oil-saturated coral-reef porosity whose areal extent is not known. Imperial Stanolind Barrhead No. 1, northwest of Edmonton, revealed the presence of oil in the Madison, and just recently Gulf N.J. Ellis No. 1, some sixty miles southeast of Leduc, found commercial production in the Leduc D-2 discovery zone. In addition to these Paloeozoic discoveries, gas and oil reserves have also been established in the Upper and Lower Cretaceous, which must be penetrated by all tests on the way through the geological column to the Devonian. If ever there appeared to be an index of 'things to come' in the oil industry, this is it. However, without these recent discoveries the picture in Western Canada does and always did, look very promising indeed. A brief survey of the geological setting in Western Canada is the object of this contribution.

Jan 1, 1949

By T. A. Lloyd

"This paper indicates the extent to which Canadian coal mine operators have taken advantage of developments in the science and technology of coal that would allow them to better satisfy changing market demands through improving the properties of their products. At some mines, no attempt is made to alter the coal from its as-mined condition, but at most mines grading into various size ranges and hand-cleaning of lump sizes is undertaken.Over-all, Canada Jags behind most of the other major world coal producers in the proportion of its coals being processed in wash plants. To some extent, this is due to the fact that a high proportion of the coal production satisfies market demands without such treatment. On the other hand, a few of the coal mines in Canada, which produce about 25 per cent of the nation's total coal output, have in operation some of the most modern coal beneficiating equipment available, including jigs, flotation cells, water cyclones, centrifuges, disc filters and thermal dryers."

Jan 1, 1968

By R. V. Fox, L. K. Sinclair, D. L. Baek

"In this study, rare earth elements were recovered from bastnasite concentrate and waste fluorescent lamp phosphors using supercritical carbon dioxide extraction with a nitric acid/tributyl phosphate adduct. Several pretreatment methods were used to alter the crystal structure of the source materials, and thus improve rare earth element recovery. Pretreatment methods included 1) dry roasting of the source material at 730oC, 2) decomposition with 50% sodium hydroxide solution at 150oC for 4 hours, and 3) decomposition with 12 M sulfuric acid at 300oC for 4 hours. Treated and untreated samples underwent supercritical extraction at 24 MPa and 65oC for 1 hour. Untreated bastnasite and phosphor samples showed <10% rare earth element recovery, but sodium hydroxide digestion resulted in >60% recovery for most rare earth elements. Dry roasting of the bastnasite concentrate was also effective, resulting in >60% recovery for cerium.INTRODUCTIONRare earth elements (REEs) consist of the 15 lanthanides, scandium, and yttrium. Scandium and yttrium are included because they are in the same group as lanthanum, appear in many of the same ore deposits as the rest of the lanthanides, and exhibit many similar chemical properties. REEs are used in a wide array of applications including electronics, magnets, catalysts, glass, and solid-state lighting (Xie, Zhang, Dreisinger, & Doyle, 2014). Because of China’s continued dominance of worldwide REE production, the United States Department of Energy has sought to diversify domestic supplies of REEs (United States Department of Energy, 2011). A key part of this strategy is the development of improved extraction methods for both ores and recycled sources.Supercritical fluid extraction (SFE) is a promising technology for extraction and separation of rare earth elements. Contact with an acid adduct dissolved in supercritical carbon dioxide allows for the rapid extraction of REEs from solid matrices. Supercritical CO2 has several potentially useful properties as a solvent, including high diffusivity and the ability to tune solvation properties by adjusting pressure. Such tunability may have applications in separating the REEs once they have been extracted from the solid phase. Tributyl phosphate/nitric acid adducts (TBP:HNO3) are a particularly promising class of adducts for SFE extraction of rare earth elements. Using TBP:HNO3 adducts in supercritical CO2, several researchers have successfully extracted REEs from their oxides (Wuhua, Pijia, & Yongjun, 2010; Zhu, Duan, Xu, & Zhu, 2009). However, there is a complication in applying this technique to many types of ores and recycled sources: REEs are often locked in refractory minerals which are resistant to acid attack, resulting in limited recovery in supercritical extraction."

Jan 1, 2016

By H. W. Manley

SULPHUR, like the minerals of coal, iron and petroleum, is one of the essential materials in our modern expanding industrial civilization. Before discussing the salient features of the production of sulphur from the Canadian sour gas, it seems appropriate to outline the historical past and probable future utilization of sulphur. The ancient Greek writer Homer spoke of its "pest-averting sulphur" and the "divine purifying fumigation". Ancient alchemists found sulphur to be a fascinating and baffling material. The discovery of gun powder in the year of 1250, and its application to the art of war a, century later, made sulphur an important commodity in the progress of mankind. The initial manufacture of sulphuric acid in the year of 1736 by the Englishman Joshua Ward, established the basis of a chemical industry that today utilizes 80 per cent of the consumption of elemental sulphur. Commercial production of the chemical soda ash ( N a2C03) discovered in 1787 by the famous Leblanc Process, in-creased international demand for the element sulphur and marks the birthday of the Sicilian sulphur industry.

Jan 1, 1961

By Troy Boisjoli, Sean Hillacre, Matt Batty

Discovered in 2014, the Arrow Uranium Deposit has undergone rapid development through successive drilling programs informed by geostatistical drill hole spacing studies. An independent third-party geostatistical drill hole spacing study was completed by Clayton V. Deutsch Consultants Inc. in 2017, evaluating the uncertainty of thickness, grade, density, and areal limit of the Arrow Deposit to determine a drill hole spacing suitable for Indicated Mineral Resources. Indicated spacing was defined to be 24 to 32 metres (“m”) to be within 15% of predicted for a nominal quarterly production volume with a probabilistic tolerance between 75 and 90%. The study not only defined the Indicated Mineral Resource resultant from the 2016 drill program, but also provided drill hole targeting criteria for subsequent drill programs aiming to convert Inferred to Indicated Mineral Resources. A subsequent geostatistical drill hole spacing study on the Arrow Deposit was completed by Clayton V. Deutsch with Resource Modeling Solutions in December 2018 to define Measured Mineral Resource spacing in support of the 2019 drill campaign. The study resulted in a drill hole spacing of 9 to 17 m to be within 15% of predicted for monthly and quarterly production volumes using an accepted industry probabilistic tolerance of 90%.

Jan 1, 2020

By L. I. Kiss, A. Larouche, V. Dassylva-Raymond

Control of the quenching capacity of the cooling water is of primary importance for maintaining the quality and recovery rate of ingots produced by direct chill casting. Industrially, this can be done using a cylindrical metallic probe undergoing rapid quenching by direct immersion in a reservoir filled with casting water. Such a test rig originally developed at Alcan Arvida Research and development Centre was modified and used to assess the role of key parameters affecting the boiling heat transfer. During the tests, the probe of the instrument undergoes the effects of different heat transfer mechanisms. An experimental study was performed in order to clarify the details of the probe-water heat transfer during rapid quenching. The heat flux along the surface was determined by mathematical modeling using the measured temperature signals, while the corresponding heat transfer regimes like stable and unstable film boiling, nucleate boiling and natural convection were identified by the analysis of high-speed video recordings. Aluminium

Jan 1, 2006