Search Documents

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By K. J. Daun, C. J. Shi

UsiborThrough the second step heating at 900 °C, the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex-situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. 5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

Jan 1, 2015

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By J. F. Wright

INTRODUCTION Eighteen years ago about half a dozen experienced prospectors moved from northern Ontario to northwest Manitoba to prospect 'greenstone' areas shown on geological maps of .parts of northern Manitoba prepared by J. B. Tyrrell, D. B. Dowling, and Wm. Mclnnes. Gold-bearing quartz was soon discovered by these men in this new field, and in succeeding years many more prospectors entered the district. A number of the pioneers are still prospecting, and since 1913 mineral deposits have been discovered each year in widely separated areas of the large district extending 150 miles eastward from the 102nd meridian and 60 miles north of latitude 54°30'. The majority of the discoveries, however, have been made near Schist, Elbow, Wekusko, and Kississing lakes. One hundred or more mineral occurrences of some merit are known, the main types being sulphide replacement bodies containing nickel-copper or copper-zinc and gold-bearing quartz veins. Some underground exploration or diamond drilling has been completed on 25 or more of the prospects. Up to the present, three ore-bodies, namely, Flin Flon, Sherritt-Gordon, and Mandy, have been proved. Of these, Flin Flon, the largest, is estimated to contain from 16,000,000 o 19,000,000 tons of copper-zinc ore carrying some gold, silver, and lead. Next in importance in regard to tonnage is Sherritt-Gordon, with a calculated reserve of nearly 5,250,000 tons of copper-zinc ore carrying less than $1.00 combined gold and silver.

Jan 1, 1931

By D. O. DeGagné, J. F. Archibald

Spray-on polymer linings, as partial or full replacement for traditional forms of area rock support, have seen rapid growth in interest within Canada. A wide variety of lining types, ranging from polymer chemical to water-based cementitious materials, have been developed and commercially introduced to the underground mining market. Following approximately one decade of development work, several general conclusions have been reached regarding the performance of this class of area support media, these being that: health and safety assessment of the broad range of materials has shown the majority of them to be acceptable and safe for underground use; significant ground support potential can be offered by them, being equivalent to or better than capabilities offered by traditional support forms such as bolt-and-screen or shotcrete, and; their abilities to be rapidly deployed and provide near instantaneous support restraint offer considerable operational and cost benefits to underground operators. A review of currently available liner materials, their historic development within the Canadian mining industry, and overviews of support, health and safety, operational considerations and cost benefits are provided in this paper.

Jan 1, 2001

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By S. Oppenheimer, P. Au, R. M. Kearsey, J. Tsang, E. McDevitt

A new superalloy, ATI 718Plus® Alloy (718Plus), has been developed to have a 55oC higher temperature capability over the traditionally used Alloy 718, while maintaining favourable processing characteristics and intrinsic raw material costs. The fatigue and dwell-fatigue behaviour of four microstructural variations of 718Plus are evaluated and compared to Waspaloy: 1) standard heat treated condition (HT1), 2) standard heat treated condition with thermal exposure at 732ºC (1350ºF) for 1000 hours (HT2), 3) fine grain condition with a modified d phase (HT3), and 4) fine grain overaged through modified heat treatment (HT4). The results show that the steady-state fatigue crack growth rates of each microstructural variation and both alloys are identical, with all of the 718Plus variations showing a clear advantage over Waspaloy in the fatigue crack threshold regime. Dwell-fatigue results show that Waspaloy has better resistance to crack propagation under dwell conditions; however, optimization of the precipitate phase shows vast improvement in the dwell-fatigue resistance of 718Plus.

Jan 1, 2010

By B. Voyzelle

The deterioration of highway and bridge infrastructure has received considerable attention in recent years because of the billions of dollars needed for repair and rehabilitation. A major factor contributing to this problem is the corrosion of steel reinforcement. Reinforcing steels with good corrosion resistance and relatively low price are therefore essential for maintenance, cost reduction and service-life extension of the steel-reinforced structures. This article describes the development of low-alloying steels that offers good corrosion resistance with reasonably low cost. Topics include steel microstructures, mechanical properties, corrosion performance, industrial applications and economic aspects.

Jan 1, 2005

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texasgulf Incorporated, operates the Kidd Creek mine, a 10,000- tpd base metal producer, near Timmins, Ontario. Two different ore types are mined and milled copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator, the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous onstream X-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8% and zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.

Jan 1, 1973

By Guojun Wang, Zejun Chen, Wenchang Liu

Al/Mg/Ti laminated metal composite sheet (LMCS) can combine the merits of each of metal components, and obtain excellent performances. It incorporates the advantages of high strength, light weight, easy melt and atomization, and good space adaptability to substitute for the bumper Al sheet of Whipple shield structure for space debris shield. The Al/Mg/Ti LMCS was fabricated by hot roll bonding technology in a certain sequence. The manufacturing process and parameters were analyzed and studied, including the first rolling reduction, roll boding temperature and stacking structure of each metal. The microstructure of dissimilar metals and bonding interface were characterized and analyzed. The optimized manufacturing procedures and parameters were presented based on the microstructure and mechanical properties of LMCS. The research results offer some guides and references for controlling the shape of bonding interface, optimizing the annealing process, improving the mechanical properties of Al/Mg/Ti LMCS.

Jan 1, 2015

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By L. Heber Cole

Introductory During the past few years, salt (sodium chloride) strata have been encountered in western Canada in a number of wells, while prospecting for oil and gas. The ever increasing number of such wells points to the presence of a vast salt basin, the boundaries of which are at present unknown. This basin extends in a northwesterly direction from a point near the United States boundary south of Regina, crosses the Saskatchewan- Alberta boundary northwest of Unity, Sask., and continues with more northerly trend to Waterways and beyond. The beds, as encountered, appear to have a general dip to the southwest of between 10 to 20 feet to the mile and a pitch along the strike to the southeast. Thus one finds the salt strata at Waterways, Alta., at 600 feet below the surface (121 feet above sea level) whereas at Radville, Sask. south of Regina, the top of the salt is at a depth of 6,643 feet below the surface (4,430 feet below sea level). Whether this is a continuous salt basin or a series of separate basins is not yet known. We do know however, that in some of the well~ more than one salt horizon occurs while in others which normally should have encountered corresponding beds, the salt strata are absent. This latter condition, however, may occur only in the southern part of Saskatchewan, where a barren area seems to come in from the southwest. In the northwestern part of the basin, on the other hand, the occurrence of the salt strata seems to be more regular and continuous, and depths at which salt should be encountered in a drill hole in this part of the basin may be predicted with a fair degree of accuracy.

Jan 1, 1948

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By A. S. Bayne

WITH the great increase in the use of power-driven machinery in industry, and consequent large-scale operations, the hazards to which , workmen are exposed have become much more numerous than at the beginning of the century. This is especially noticeable in mining. In the past thirty years or so, improvements in methods of excavation and metallurgy have made possible the exploitation of deposits which would have failed to make ore in previous years. This improvement, together with the in-creased use of machinery, has facilitated the mining of tremendously greater tonnages with a marked decrease in unit cost of production. This 'speed up' in mining creates numerous problems demanding close attention of operators and necessitates careful prep;tratory planning, as well as diligent supervision of actual operations. Underground openings increase in size so fast, and all phases of mining, mucking, and transportation proceed at such a rate, that a short period of reduced vigilance on the part of operators . results in disaster, both from the standpoint of safety and economies. Happily, the challenge of increased hazards has been successfully met by a general application of the slogan 'Safety First'. Today, we have large manufacturing concerns devoted entirely to the development and production of safety equipment for the protection of workmen in various branches of industry. Machinery manufacturers, in co-operation with their mining customers, have included the best possible in foolproof devices in the manufacture of hoists, compressors, boilers, electric motors, and equipment of all kinds. Mining companies and private individuals spend thousands of dollars and devote a great deal of time to research with the single object of preventing accidents and combating miners? diseases. Governments throughout the world have written regulations into their statures for the protection of miners and operators. Staffs are appointed to enforce these laws and investigate accidents to ascertain means of preventing them for the future benefit of the industry.

Jan 1, 1938

By M. J. Gagnon

The agglomeration of particulate materials is used in many mineral processes to enhance the settling of the fine particles, Depending upon many physical and chemical parameters, the aggregates demonstrate specific density-size distributions, In this study, a fractal model of the agglomeration process is introduced, Based on reliable experimental data and on physical calculation, the model presented helps to envisage the initial formation of the micro-flocs, and to interpret the subsequent interactions between the aggregates in terms of either coagulation or flocculation, Data from different sources, materials and different agglomeration processes are analysed and compared in the light of the proposed model.

Jan 1, 2005

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960

By J. Qi

Based on the commercial steel 42CrMo (4140, SCM440), a new generation of CrMo steel was developed by increasing the content of Mo, adding the alloy element of V and Nb, and decreasing the content of P and S. This new CrMo steel has higher strength of 1500MPa and better delayed failure property. TEM and EDS were used to study the distribution and function of the alloying elements in this steel. A new EELS technique was developed to study the bonding strength of the grain boundary in the steel. The mechanism of strengthening of the new steel has been studied.

Jan 1, 2004