Search Documents

By B. Hohenstein, B. McBain, B. de Jong

"The automated fire assay system (Fast In-line Fire Assay or FIFA) has not found acceptance in the Au mining industry as the lower measurable limit of 0.20 ppm did not allow Au tailings to be measured with confidence. The development of arrested cupellation has overcome this hurdle which was a limiting factor in the FIFA 1 process. In the new automated fire assay process, automated sample preparation, fluxing, fusion and separation of a Pb button are essentially similar to the FIFA 1 process, albeit with some improvements. However, the game-changer is the development and incorporation of arrested cupellation into the automated system, now called FIFA 2. The purpose of arrested cupellation is to reduce the 50 g Pb button to a 5 g Pb button by partial cupellation in a specially developed arrested cupellation system thereby concentrating the Au in the Pb by a factor of 10 and in so doing moving them into higher concentration ranges in the mini-button where they can be read on the spark spectrometer. Results show that concentrations down to 0.02 ppm Au in geological materials can now be determined using arrested cupellation in the FIFA 2 process, an order of magnitude improvement over FIFA 1.INTRODUCTION Traditional fire assay for Au has remained virtually unchanged for 3000 years. It has survived for so long because it is accurate, has relatively low detection limits and is relatively inexpensive. However, it is labour intensive, has a long turn-around time (typically at least 7 hours), is environmentally unfriendly and exposes assay operators to potentially unsafe conditions (toxic fumes, toxic dust and extreme heat from furnaces). The NiS collection method is not as effective for the assay of Au as it is for the PGEs. A rapid, accurate, cost-effective method for the determination of Au and the Platinum Group Elements (PGEs) in geological materials would be a tremendous benefit to mining companies. Many of these objectives have been met by the FIFA 1 (Fast In-line Fire Assay) developed some 15 years ago in which automated methods have replaced the manual procedures which are part and parcel of conventional fire assay. However, concentrations below 0.2 ppm have been very difficult to achieve with sufficient reliability."

Jan 1, 2017

By J. M. Simard, S. Morissette, P. Coursol, P. Mackey

A new, powerful model is presented that focuses on plant logistics and scheduling aspects of the smelting, converting, fire refining and casting operations at the Horne smelter. This plant complex is the largest custom copper smelter in North America. It handles a wide range of feeds and utilizes a number of proprietary continuous and batch technologies that require good scheduling in order to maximize plant capacity and efficiency. The present model was developed by Xstrata Process Support, in collaboration with the Horne smelter, and uses the Arena® software to evaluate the impact of a number of plant variables on the annual copper capacity of the plant. Model development was carried out by Xstrata Process Support, in collaboration with the Horne smelter, through the effective combination of process chemistry knowledge and detailed knowledge of the plant operation (including all material flows and transfers, as well as information such as operating on-line times, plant stoppages and also scheduled and unscheduled maintenance activities). A number of case studies were then examined, including the impact of anode furnace and casting cycle times on annual copper capacity and the impact of a one-crane mode of operation in the converter aisle, which normally operates with two cranes in service. The model predictions were found to match actual plant results very well. The present modelling of plant logistics and the scheduling aspects were found to add important dimensions at the plant with regard to projections of the real-life plant capacity. As demonstrated in the present case, this type of model and application can have a significant impact on optimizing operations at a given plant. This impact is particularly important in the current market environment, where emphasis is on maximizing plant output and lowering costs. These models can help yield the easily obtained gains that are clearly desirable in these times. Xstrata Process Support has developed Arena models for other operations and is available to explore new applications for a win-win situation at other plants, including mines and concentrator operations.

Jan 1, 2009

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

To produce high quality castings, one must monitor the melt quality by evaluating such parameters as the grain refinement and silicon inoculation and modification during the production of the commercial casting. Thermal analysis is a tool one can use for both monitoring and providing input to the process control of the operation. The current technique of performing thermal analysis in commercial foundries is to pour a relatively small quantity of the molten aluminum alloy into a sampling cup and to then acquire the cooling curve. This approach is somewhat simplistic in that one has limited control of the cooling rate and hence the solidification rate of the sample. Moreover, this process requires a fair amount of user intervention and effort. In the past, studies have been conducted in an attempt to develop a system for conducting thermal analysis in-situ. In a study at McGill University, an alkali based heat pipe system was developed for conducting thermal analysis in-situ. While the concept was deemed as very desirable, the complexity of the equipment and procedure was a substantial negative component. In order to improve the technique of accomplishing real-time thermal analysis with an in-situ probe, a new method that is based on McGill heat pipe technology was developed. In the new system, a controllable and flexible water based heat pipe probe is used to solidify a small quantity of metal while residing in the melt. The solidified aluminum is remelted after completing the thermal analysis. This is a key feature of the probe. It resides permanently in the melt yet it is able to both solidify a sample of the melt and then to subsequently remelt it. Various solidification rates encountered in commercial castings are attainable by adjusting the heat extraction rate of the unit.

Jan 1, 2004

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013

By T. Patching

"A GLANCE BACK AT what has happened in the past is often a useful guide to the future, although it should be used mainly to provide a sense of direction rather than a map that must be followed. As a preamble to discussing some of the questions posed by the organizing committee it may be appropriate to briefly review the distribution and careers of the graduates of our Department since the first degree in mining engineering was awarded in 1916. An attempt has been made to keep a record of the locations and careers of the Department's 540 graduates in mining and metallurgical engineering. Almost all of those who graduated before 1930 have now retired, but a very large proportion held positions as senior executives prior to retirement. A major proportion of those who graduated before 1950 are now in what might be considered senior management positions. Those who have 10 to 20 years of experience are generally in work of senior engineering responsibility or in supervisory or junior management ranks, while those who graduated in the last ten years appear to be generally in staff engineering or junior supervisory positions. This classification is admittedly imprecise because it is difficult to determine from a job description whether duties should be considered of an engineering or management nature - a distinction between the two terms is often over-emphasized. Nevertheless, the trend from technical engineering to management responsibilities with seniority and years of experience is clear in the careers that we have been able to follow."

Jan 1, 1972

By P. O. Sandvik, George Erdosh

"AbstractThe Cargill phosphate deposit, located 32 kilometers southwest of Kapuskasing, Ontario, was discovered by the Resource Development Group of International Minerals & Chemical Corporation in 1975 and has been evaluated through an extensive program of 190 drill holes, numerous chemical analyses, metallurgical tests, and engineering and economic studies.The Cargill alkalic complex, comprising principally car-bonatite and pyroxenite-amphibolite rocks, was intruded in to the rift system of the Kapuskasing High during late Precambrian time about 1,800 million year s ago, near the intersection of northeast- and northwest- trending faults. The Cargill complex is one of at least ten known alkalic complexes in or close to the Kapuskasing magnetic-gravity-high system and is expressed by an elongated, northeast- oriented, three-part magnetic anomaly 7.2 kilometers long by 2.8 kilometers wide . Weathering and leaching under assumed temperate to cool, moist climatic conditions , and controlled by faulting, shearing and/or initial petrographic variations within the carbonatite , developed a small, locally confined karst system in the car bonatite rocks and resulted in a thick enriched leached carbonatite zone, capped by troughs and sinks, filled with a residuum of apatite, goethite, clay and other minerals stable in the near -surface, oxidizing environment. Overburden is 5 to 165 meters thick."

Jan 1, 1977

By C. W. MacLeod

LOCATION The Goudreau gold area in Ontario extends from a point a short distance south of the main line of the Canadian Pacific railway, at Lochalsh, in a south-westerly direction to the Magpie river. It crosses the Algoma Central & Hudson's Bay railway at Goudreau station, 177 miles north of Sault Ste. Marie. The area is roughly 25 miles in length by 6 miles in width. The potential gold formation is much more extensive but little prospecting has been done outside of the limits mentioned. The actual continuous area of Keewatin formation, in which gold has been found, is one of the largest in Ontario. ACCESSIBILITY Probably no mining area in a similar stage of development has had the excellent transportation facilities which Goudreau enjoys. This field is traversed in part by the main lines of the Canadian Pacific and Algoma Central railways. The Provincial Government has constructed 22 miles of road through the heart of the camp. Sixteen miles of this road is suitable for motor car traffic and several cars and trucks are in constant service.

Jan 1, 1926

By H. C. Cooke

"The Part of the Eastern Townships dealt with in this paper is shown in the accompanying figure. Each rectangle represents one of the topographic maps published by the Department of National Defence on a scale of one mile to one inch. Each sheet covers an area approximately 24 miles long and 17 miles wide, or slightly more than 400 square miles. The north-western part of the area figured, comprising the Upton, Aston, Becancour, and the two unnamed sheets, (Three Rivers and Yamaska), together with most of the Lyster, Drummondville, and St. Hyacinthe sheets, is largely covered by clays and sands deposited in interglacial and post-glacial time in the Champlain estuary, so that outcrops are widely scattered and in-formation is correspondingly sketchy. In the remainder of the area figured, comprising more than 4,000 square miles, outcrops are reasonably numerous and have been mapped on a scale of one mile to one inch, and the structure is moderately well understood.The Eastern Townships was an area of intense orogenic disturbance, apparently beginning late in the Cambrian or early in the Ordovician, and continuing till well on in the Devonian period. During this long period, which may have lasted for a hundred million years or more, the area was subjected from time to time to intense thrusts from the east and southeast. Each of these caused folding of the rocks, accompanied by faulting, raised parts of the area above sea-level, and presumably created ranges of mountains. Long periods of erosion cut away the mountains and reduced the area nearly to sea-level after which subsidence carried it below sea-level, and permitted further sediments to accumulate before the next thrust initiated the next cycle.The first of these movements, as stated, appears to have been in late Cambrian or early Ordovician time. The group of rocks known as Caldwell was folded and, south and east of the town of Asbestos, was thrown into great drag-folds before deposition of the next overlying series, termed the Beauceville, began. Unfortunately, the date of this orogeny is very imperfectly known, because both series of rocks have been so crushed and sheared that almost all fossil remains have been destroyed. Graptolites, found in one place in slates generally considered Beauceville, give that series a tentative Middle Ordovician age. In the Caldwell rocks, which underlie the Beauceville with great unconformity, no fossils whatever have yet been found. Thus, if the Beauceville rocks are correctly dated as mid-Ordovician, the best that can be said of the movement folding the Caldwell is that it took place at some time before Middle Ordovician."

Jan 1, 1949

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

By W. L. Bancroft, Peter Price

"What is now known as the 'Waite section' of the property of Waite Amulet Mines, Limited, was originally the Waite-Ackerman-Montgomery mine. It includes a group of twenty-eight claims lying on either side of the Duprat-Dufresnoy township line, and about 8 miles north-northwest of Noranda, Quebec. ,The original discovery of ore on the property was made by Thomas Montgomery in Block Q, Duprat township, and was staked by him on behalf of himself, I. C. Waite, and C. H. Ackerman, in the summer of 1925. The property was optioned late in 1925 to N. A. Timmins who, after trenching and drilling the deposit, sold his 85 per cent interest to Noranda Mines, Limited. Early in 1927, a company known as Waite-Ackerman-Montgomery Mines, Limited, was formed and shaft sinking and development undertaken. Production commenced in August, 1928, ·and continued tJ May, 1930, when, owing to falling metal prices, shipment of direct smelting ore was stopped. Development of the mine by shaft sinking, drifting, and drilling continued until March, 1932, when owing to the prolonged low price of metals, the property was closed down. In September, 1933, an amalgamation with Amulet Mines, Limited, was effected, the new company being called Waite Amulet Mines, Limited. Early in 1937 operations were resumed, first by direct shipments to the smelter and later by aerial tramway to the Amulet mill. Operations have been continuous up to the present time, reaching an average of 720 tons a day milled for the year 1940. Production during the initial period (1928-1930) amounted to 75,811 tons, having an average grade of 7 .11 per cent copper, 4.47 per cent zinc, and 0.03 oz. gold and 0.65 oz. silver per ton. During the second period (1937 to end of 1946) , 1,060,524 tons, having an average grade of 4.53 per cent copper, 2.97 per cent zinc, and 0.03 oz. gold and 0.65 oz. silver per ton, were produced."

Jan 1, 1954

By H. Link

"The extremely low permeability of the water-carrying beds in the nevonian formation of the potash district of Saskatchewan does not permit the injection of cement or chemicals to seal off sufficient water from the shafts to guarantee the safety of the mine. Based on many years of experience with wet shafts in the German and French potash mining industry, Alwinsal Potash of Canada Ltd. decided to have their potash mine shaft near Lanigan, Sask., which was completed in September of 1967, lined by means of an absolutely watertight lining of combined concrete and steel-plate construction.This shaft lining, consisting of two steel shells of welded construction with concrete filled in between, has proved itself before in the German coal mining industry. It guarantees a permanently dry shaft. With this type of lining, time-robbing and very often abortive injections are superfluous and the regular repair and adjusting work as well as the corrosion of conveyances and ropes can be avoided. Above all, however, the danger of a water inrush into the shaft is abolished completely."

Jan 1, 1971

By A. McEachern

At the Annual Meeting of this society, held in Halifax last year, a paper entitled "Closed System Breathing Apparatus" was read by I. C. Mackie, metallurgist, British Empire Steel Corporation. Coming from such an authority it was most instructive and illuminating. The purpose of the paper was to emphasize the necessity of a full supply of oxygen and the danger of oxygen shortage in the use of rescue breathing apparatus. In connection with this he pointed out: "In times of emergency, when life is at stake, rescue men cannot be restrained from using their utmost endeavor, and unless the apparatus is adequate to meet the heaviest load, the result may be fatal to the wearer. The body's demand for its oxygen requirement is absolutely imperative and must be granted at once. We can do without food for many days and without water for many hours, but we cannot do without full requirements of oxygen even for a few minutes. Furthermore, the victim of oxygen shortage gets practically no warning. He may fall helpless or unconscious before realizing that he is in a serious condition." Hence the necessity for expelling all the nitrogen from the breathing-bag and filling it with pure oxygen; also filling the lungs of the wearer with oxygen before he begins to use the breathing apparatus. This practice is general at all the collieries under the British Empire Steel Corporation.

Jan 1, 1924

By J. Huh

Recently, there is growing trend to build the high-rise and install curtain walls. Following this trend, we developed robot for building wall cleaning work, which moves along Built-in guide rail of building. Because it moves attached at building wall for cleaning work, it can be seriously affected by potential threats, like earthquake, strong wind, malfunction, and construction error of built-in guide rail. In order to cope with those threats actively, this paper presents the Fail-Safety system. The building wall cleaning robot consists of two moving system: The Horizontal Moving System which mainly do maintenance work, and The Vertical Climbing System which transport the horizontal moving system floor by floor. We apply the Fail-Safety system to these systems. The Fail-Safety system consists of sensors to detect external situation, and, with information of sensors, give instruction for what to do. This robot system is installed with four kinds of sensors: shock sensor, infrared ray sensor, laser sensor, magnetic sensor. First, shock sensor detects external shock during cleaning work. When shock sensor detects big shock, the robot returns to starting point to inspect how damaged it is. Second, infrared ray sensor detects damage of built-in guide rail. It is to prevent destruction of robot caused by moving along damaged rail. Third, laser sensor gives notice about where obstacle is. It is for robot to avoid crash with obstacle and decrease damage. Fourth, magnetic sensor detects magnetic points, which are installed in rail at regular intervals, and helps robot to find its position, based on location of magnetic points detected. If robot is damaged by external shock and its encoder, which gives information of location to it, is not working, magnetic sensor will give information of robot?s location to robot. And then, robot regulates its velocity depending on position of it, and safely returns to starting point. The Fail-Safety system in this paper is for building wall cleaning robot to sense external threats, and prevent getting worse. Applied to this active protection system, making safe environment of maintenance work is possible for robot system.

Aug 1, 2013

The writer presents a concise summary of eleven recent discoveries made in the Maritime Appalachian area, with suggestions for fur the research. This information may prove helpful to geologists working in other fields and to students contemplating further avenues of research in mining geology and exploration. INTRODUCTION THIS paper is not intended as a research study on the subject, but i. merely a brief review of eleven discoveries that have been made in the Canadian Appalachian area. Furthermore, this is not a critical analysis of the merits of any one geophysical method, but it is an un-prejudiced observation of how these discoveries were actually made and what techniques were apparently most fruitful. Some generalizations are attempted whicl1 may suggest further avenues of research in the field of mining exploration. The writer wishes to thank his colleagues in the field for their comments, which he was able to in-corporate into this paper. In particular, he is grateful to Dr. Paul Bevan and

Jan 1, 1963

By A. G. Doll

The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less. This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference.

Jan 1, 2012

By Solar D. Andrés

Several large open pit mines are facing the challenge to design and plan an underground transition to sustain the long term future of their operations. The desired underground method is Block Cave since its natural high productivity and low operating cost that could compete against the open pit cost to mine the final open pit pushbacks. It has been found at several operations where this transition is taking place that the pit limit at which transition is performed is rather deep. This aims to think that perhaps several transition projects have started late in the life of an operation producing an over stress in the transition project and reducing the flexibility in the design of the overall infrastructure and a substantial lost in the complete project NPV. Traditionally the approach to plan open pit underground transition consists of sequentially deciding the final pit using a Lerchs and Grossman type of optimization to find the overall maximum pit shell and then running block cave simulations to find the best footprint for the underground option. The research summarized in this paper is related to the development of an integer linear programming model that aims to compute simultaneously the maximum NPV of the combined option final limit open pit and block cave underground footprint. The model has been tested using two large block models representing two of the current operations in the process of transiting from open pit to underground operations. Finally, the integrated open pit underground transition model is going to be compared to the traditional sequential approach in order to define which method achieves the best NPV. The paper illustrates both case studies in depth.

Oct 1, 2009

By Joanna LaForte

"In response to “Arctic Mineral Wealth —Equitable Participation with Aboriginal Landowners – A slow or fast process?”, this author’s impression is one that, to her, seems obvious — this is definitely going to be a slow process. To question this issue seems ridiculous, unless the mining industry is considering following the same patters of the past, thereby adding to the suppression and injustices to which the aboriginals are so accustomed. To make genuine progress, where trust and good communication has been achieved with time as a factor in proceeding, the author feels, without a doubt, that the triangle of industry, government and aboriginals will seriously have to be restructured or eliminated. Anytime you mix government with progress, along with other problems, you are looking at bureaucracy, and that takes time. Issues such as the settlement of land claims have not been resolved, and in all likelihood could take forty years to finalize. Aboriginals have been suppressed for centuries by governments and industries with ethnocentric ideologies, and now that they are in a position to reclaim their lands, attain their own economies and government, and truly secure a wealthy, self-sufficient legacy for their descendants, how can anyone imagine they’ll move quickly? This author also strongly disagrees to some sections of Mr. Wakefeld’s article and will expand on her objections.We question whether aboriginals under-stand the process of mine development. If we encounter an electrical problem in our home, o we not call an electrician without having to learn the trade ourselves? This comparison seems simplistic, but does convey a point. As cited, “there are now over 100 000 aboriginals who have completed post-secondary education.” Are the numbers revealed in Mr. Wakefeld’s paper there to scare us? Is he suggesting that without the industry’s haste, the aboriginal’s new found intelligence could pose a problem to the mineral explorer. While it is true that not all are highly educated, the aboriginals have specialists in market fluctuations, feasibility studies and the needed skills. They have specialists, such as their representative organization of COPE 1984, (the Committee for Original People’s Entitlement), who under-stand their cultures, language and desires. Their education should expedite the negotiations and end the power struggles equitably. Aboriginal people are not stupid. Once they have reason to be proud, regain their communities and know the direction that they’re headed, their self-determination will return."

Jan 1, 1996

By Roger M. Jones

This paper comments on developments in bulk shipping which will be of direct interest to those who are considering the shipment of dry bulk minerals out of Nova Scotia by water. Various conveying systems, and the slurry system of loading, are considered, and the role of deep water ports as a catalyst to other industries is stressed.

Jan 1, 1971

By Richard N. Zimmer

This paper discusses the installation of corrugated steel linings in bored raises at Inco's Thompson Mine. The procedure for the installation of these linings is outlined and the relative advantages are compared with conventional methods of ground support. Future trends in the use of corrugated steel products are then discussed.

Jan 1, 1978