Search Documents

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks, R. L. Sachdeva

"A combined shaft-electric furnace for the smelting of ores and the melting of metallized iron pellets is being developed. The materials are preheated, and in some cases pre-reduced, in the shaft before being transferred to the electric furnace, where melting or smelting is completed. It has been demonstrated that this combination of equipment will enable much of the relatively expensive electrical energy to be replaced by cheaper energy in the form of oil or natural gas, and preliminary experiments indicate that the total energy requirements for a melting or smelting operation are significantly reduced. Projections based on results obtained from the preliminary experiments indicate that further improvements will be possible when certain modifications to the equipment are completed."

Jan 1, 1968

By N. Shi, T. G. Joseph

ABSTRACTA series of algorithms were developed to perform geometric and kinematic analyses of cable shovel dipper-ground interactions for a given set of mining face conditions. The routines examine and analyze (a) the position of the dipper in relation to the shovel; (b) the dipper in relation to the face conditions; (c) the dipper position in relation to possible interference or collision with crawler tracks during digging cycles; and (d) kinematic and geometric considerations with respect to any point on the dip-per as it conducts a duty cycle. In all cases, field measurement verifcation provided good agreement(within 4% variance).

Jan 1, 2011

By R. L. Bishops

This paper discusses some of the materials, processes and systems used in motor insulation. Among the materials mentioned are epoxies, polyesters, mica paper composites and wire enamels. Two processes developed to take advantage of the special characteristics of two of these materials are described, and how these materials are used in several new insulation systems now on the market is discussed. Finally, future trends in motor insulation are outlined.

Jan 1, 1969

By John Kostuik

"This paper discusses the outlook for uranium resources, and comments briefly on the measures needed to meet market objectives. Areas of recent exploration interest are also discussed.THE PREVIOUS SPEAKER has capably described the truly phenomenal growth in demand for energy from all sources. The basic factors -population growth and industrial development -which will create energy demand are so fundamental to national economies that the ascending energy demand curve will be little affected by short-term factors.Because of the economic and practical advantages of nuclear power and the degree of present acceptance by electric utilities, there is no doubt that uranium will be a principal source of primary energy in industrial countries -and this will happen within a decade. Indeed, during this period it will be the fastest growing source of energy, capturing, for example, more than half of the electric utilities' expansion in the United States by 1980. The ready availability of energy sources from domestic and foreign resources is so essential to industrial nations that the long-range outlook for their adequacy is of prime importance. There has been international concern about the availability of uranium resources at reasonable cost to adequately support and foster the development of the nuclear power industry. Canada, fortunate in having established reserves and a potential in excess of any forseeable domestic demand, can confidently look forward to being a principal supplier to the industry."

Jan 1, 1969

By Zhenyu Han, Dion Weatherley, Ruslan Puscasu

"This study aims to demonstrate the capacity of the Discrete Element Method (DEM) to model and simulate fracture in brittle rock, capture the crack propagation process and determine crack propagation rates for various levels of external loading. In the numerical experiments reported here, a macroscopically homogeneous body of brittle rock, containing a single pre-existing crack, was subjected to tensile stress loading. Simulations concerned with model I crack growth process in 3D were carried out. The process of fracture has been observed under various steady state and dynamic conditions. The numerical results obtained reproduce qualitatively and quantitatively a variety of observed fracture phenomena. Specifically, this study examined the onset of cracks, single dominant cracks that grow across the specimen, crack bifurcations and branching. The density of fractures that can be nucleated and grow to a significant size with and without arresting each other, crack growth speed and stress distribution, all have been consistently and systematically analyzed. Suggestions on potential future developments are made and discussed.INTRODUCTIONFracture and failure mechanics are very important in mining, manufacturing, materials processing, mineral processing, civil and mechanical engineering, and many other disciplines of science and engineering. Yet, due to the complexity of fracture phenomena, no theoretical models of broad applicability are currently available (Bieniawski 1967). The simulation of crack propagation is therefore considered an open question in numerical rock mechanics. Although, a significant body of experimental research on fracture of materials was carried out since the early days of fracture mechanics (circa 1940s) (Poncelet 1946, Mott 1948), often in parallel with the development of fracture mechanics theories as well as with the development of experimental and observational techniques themselves, the experimental results were often done on particular classes of material such as glasses and other very brittle materials. Indeed, a number of specific experimental observations on the behavior of growing cracks in brittle materials were made in the 1940s for which generally accepted explanations based on physical principles are still lacking. Likewise, quantitative numerical modeling, based on both continuum and discrete methods, as a basis for understanding dynamic crack growth is still in a preliminary stage."

Jan 1, 2015

By Marco Quirion

The Daniel-Johnson dam, formerly named Manicouagan-5 (Manic-5), is located 800 km northeast of Montreal (Quebec) in Canada. This is the largest multiple-arch concrete dam in the world consisting in 13 arches and 14 buttresses. Since its construction in 1969, various type of cracks have appeared on both downstream and upstream faces of almost all the arches of this concrete dam. As a part of the Daniel- Johnson’s dam safety assessment program, Hydro-Québec is currently performing structural analysis of the dam with advanced numerical models to better understand and predict the dam behaviour. Because the buttresses transmit all the arch loads to the rock mass, determination of the properties of the dam foundation should not be neglected in dam global safety analysis and also to insure that reliable input parameters are used in the dam numerical simulations. This paper summarizes the past and the more recent investigations of this foundation used to assess its safety and stability. Moreover, the use of rock mass classification to estimate the deformation modulus, based on empirical equations, gives values in the range of 30 to 40 GPa that are higher than expected values. Using those values in the numerical simulations for dam structural analysis gives an excellent correlation with displacements monitoring of the buttresses.

Jan 1, 2015

By L. V. Bell

"The gold deposits of the Caribou mine are representative of those of the Province of Nova Scotia as a whole. The ore shoots within the deposits, in common with those elsewhere within the Province, are associated usually with interruptions or irregularities in the broader and uniform fold structures. The structural factors localizing ore deposition as applied more specifically to the Caribou mine are demonstrated chiefly by the close relationship of the two principal ore shoots, known as the main orebody and the 'high-grade' vein, with a pitching drag fold developed in the southeast limb of the major northeast-southwest trending anticlinal fold or elongated dome that constitutes the primary structural feature of the Caribou gold district. It is of interest to note that the evidence indicates that this drag fold, in common with other folds subsidiary to the primary fold, formed as a result of movement similar in nature to that which caused the primary fold itself. Presumably, therefore, these folds are coincident in time.The property described here as the Caribou mine is an amalgamation of two adjacent properties formerly known as the Ross and the Nova Scotia Gold, but which since 1934 have been controlled and operated as a unit by The Consolidated Mining and Smelting Company of Canada, Limited. The Caribou mine is situated in the Caribou gold district about 45 miles to the northeast of the city of Halifax and about 6 miles to the north of the Moose River gold district.The history of mining at Caribou dates back to 1867. The first recorded gold production is for 1869. From 1869 to 1933 the gold produced from the mines of the Caribou district aggregated 47,249 oz. from 93,234 tons of ore treated. The grade of the ore on the basis of the gold actually recovered from the district would thus average 72 oz. gold a ton, which, as will be noted from the following, is precisely the grade of the ore treated from the Caribou mine during operations by The Consolidated Mining and Smelting Company. These operations commenced in September, 1934, and milling on a commercial basis was under way during 1938. Since that time production, apart from a short period in 1945 during which efforts were concentrated on development work, was continuous to early in 1947, when the mine closed down owing to exhaustion of the known orebodies. Gold produced from the Caribou mine by The Consolidated Mining and Smelting Company from September, 1934, to the close of 1946 aggregated 43,205 oz. from 90,754 tons of ore milled; the grade of ore treated averaged 0.50 oz. gold a ton. The indicated average grade of O.S oz. gold a ton for the ore of the Caribou district throughout its mining history ranks somewhat higher than the 0.37 oz. a ton average for the ore milled to date from the several gold districts throughout the Province as a whole according to the production statistics of the Provincial Department of Mines."

Jan 1, 1954

By P. R. Geoffoy, T. Koulomzine

"The discovery of the Mogador deposit concealed by 100 feet of overburden was the result of combined application of geological reasoning, ground geophysical surveys, studies of glacial float and extensive diamond drilling. The ground was acquired because it lay on the projected intersection of the Manville and Laflamme River faults. Systematic ground prospecting led to discovery of mineralized floats. A first unsuccessful exploration campaign lasted several years and consisted of 137 drill holes.In 1951 the boulder nests were reexamined and an associat'on of the mineralized float with boulders of a granodiorite, unknown in outcrops of the district, was established. Consequently, ground magnetic surveys were extended and re-interpreted, and a large anomaly interpreted as corresponding to a batholith was outlined. The existence of the batholith was immediately confirmed by drilling and the Mogador deposit discovered in third hole of new drilling programme in a zone of fractured volcanics paralleling southern contact of batholith.The Mogador deposit is a complex replacement of silicified volcanics by pyrite, pyrrhotite, sphalerite, chalcopyrite and galena carrying values in silver and gold. A total of 1,230,000 tons has been indicated, most of it now classified as fully developed proven ore."

Jan 1, 1960

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By A. Eslami

When producing high grade mattes in smelter plants, copper losses in the slag are inevitable. Hence, the recovery of copper from slag has been the focus of many research projects, copper flotation being a widely used process. In the Khatoonabad converter, 200 t/d of slag are presently produced with a grade of 2.3% Cu. Assuming a 85% recovery by flotation, about 3.9 t/d copper could be produced, which is of prime importance economically. In the present work, a sample of this slag was crushed and ground in the laboratory to liberate the copper-bearing minerals. Following mineralogical studies, optimum laboratory flotation parameters were obtained, resulting in 90.27 % recovery and 9.42% of copper grade for the rougher stage. At pilot scale, a pulp of 28% solids was floated at ph 10.5 using 40 git of Z6, 25 git of R407 and 20 git of MIBC and A65. A recovery of 83.52% was obtained for a concentrate grade of 28.36% Cu. In the rougher cells, the feed consisted of particles 94% finer than 74 microns whereas in the cleaning stage, particles were 95% finer than 44 microns. Based on the obtained results, the Sarcheshmeh Khatoonabad converter slag is presently being fed to the Chargonbad flotation plant, where a concentrate of 32% copper at 86% recovery is being produced.

Jan 1, 2007

By Pura Alfonso, Teresa Escobet, Hernan Anticoi, Eduard Guasch, Josep Oliva, Sarbast A. Hamid

"The liberation modelling of mineral particles using mineral liberation analysis have been used in the past to model comminution and concentration processes. In this work this concept has been taken a little further, using comminution and concentration for applying the mineralogical characteristics of particles. This approach is shown using the image analysis, mineral liberation analysis and the distribution density functions for liberation modelling. The work focused on the effect of comminution on mineral liberation for liberation modelling. To model this, effect the mineral liberation of the particles using distribution density and the cumulative distribution was linked to the image analysis of the ore particles. These properties have been estimated by statistical measures such as the distribution density and liberation grade, which were extracted from MLA data and images analysis, using proper image analysis and techniques based on MATLAB software. A comparison of different tungsten ores of liberated particles, has been introduced and evaluated by estimated results and image analysis.INTRODUCTION The chief economic minerals of tungsten are wolframite [(Fe,Mn) WO4] and scheelite(CaWO4), and approximately two-thirds of the world tungsten reserves consist of scheelite deposits (Lassner and Schubert, 1999). Tungsten has unique properties and is widely used in various industrial high strength and high temperature applications. It occurs coarsely aggregated in low grade ores. Most of tungsten ores, particularly scheelite, wolframite and ferberite, occur in deposits with very low content of WO3 (0.1–2.5%) that is not economically viable to apply directly metallurgical methods to extract tungsten (Martins, 2014). Tungsten is considered as a critical metal by the European Union by the economic importance and also the high supply risk (European Commission, 2014; Chakhmouradian et al., 2015).Currently, scheelite is playing an increasingly important role in tungsten industry because the mineral reserve of wolframite is getting depleted after gradual exploitation and utilization (Min et al., 2016). In mineral processing, the liberation of valuable mineral from the gangue determines the efficiency of subsequent separation processes. The liberation characteristics of an ore are primarily dependent on its texture, the association of mineral in the host matrix of gangue minerals, and to some extent on the grinding process (Zhang and Subasinghe; 2013)."

Jan 1, 2017

By C. Fortin

ABSTRACT The subject of gold flotation has been reviewed extensively. Most of these reviews focus on the theories of gold flotation and the physical and chemical effects that may impact the efficacy of the gold flotation process. The current status of gold flotation chemistry as it is being applied in industry has not been widely addressed. This paper reviews current gold flotation practice and research advancements and discusses how these applications tie in with the current understanding of gold flotation chemistry. Survey results from worldwide gold flotation operations are analyzed. Potential future areas of gold flotation research are highlighted.

Jan 1, 2013

By Claude K. Howse

The area covered by the present paper consists of about fifty square miles in the immediate vicinity of the settlement of St. Lawrence, which is on the Southern extremity of the Burin peninsula on the south coast of Newfoundland. Physiography Physiographically, the area is part of the Atlantic upland, equivalent to the New England province of the United States. Evidences of two erosion surfaces are to be seen truncating the intrusives and the folded volcanics and sedimentary rocks. The older erosion surface is represented by small monadnocks from 650 to 750 feet in height with the younger surface covering most of the area and characterized by rounded subdued topography with maximum relief of two to three hundred feet and numerous ponds and bogs. These surfaces have been correlated with the High Valley and the Lawrence peneplains of Newfoundland. On the Avalon peninsula, these peneplains have elevations of, respectively, from 1,300 to 1,700 feet and from 500 to 1,000 feet. Glaciation The entire peninsula has been glaciated, with lee-and-stoss slopes showing on the highest hills in the immediate vicinity, many of which have striae and erratics on their summits. The lee-and-stoss slopes, the glacial striae, and the distribution of certain rocks found in the drift and whose source outcrops are known, indicate a southward direction of ice movement.

Jan 1, 1951

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Knowing shear mechanism of discontinuities under monotonic and cyclic loading conditions is a key factor in stability analysis of rock slopes and rock foundations. In this paper, the effect of cyclic loads on the shear mechanism of joint asperities is described. For this purpose, a fresh tension-split joint from a granite block was used as a reference and thirty five mortar replicas were fabricated. Cyclic shear tests were conducted on replicas under low values of constant normal load (CNL) using a servo-controlled loading system. Tests were performed in two consecutive steps; load-controlled and then displacementcontrolled. In the load controlled part, after initial increase of shear stress to 0.25 MPa, the test was stopped for 2 minutes, then increased to 0.5 MPa, and finally decreased to 0.25 MPa. This process was repeated ten times. At the end, the test was continued up to 10 mm shear displacement under displacement-controlled loading in order to pass the peak shear strength and reach the residual strength. Characterizing joint surface and modeling of involved asperities during the tests was undertaken using a Matlab code developed with new mathematical expressions. The algorithm used in the code is based on three-dimensional coordinates of the scanned joints’ surfaces before and after the test. It was found that a high percentage of degradation happens during the first cycle of loading and during the other cycles, degradation occurs gradually. While comparing tests conducted in monotonic and cyclic loading conditions, it was observed that under low number of cycles, the pronounced mechanism is consolidation of the joint surfaces. This consolidation increases contact areas and, therefore, shear strength parameters.

Jan 1, 2015

By G. D. Bateson

"The Low NOx/SOx (LNS) Burner is a technology which, in pilot-scale tests, significantly reduces acid rain-forming emissions from the burning of coal. The precursors of acid rain are nitrous oxides (NO) and sulphur dioxide (SO:;) . TransAlta is currently planning two demonstration projects.Esso Resources Canada and TransAlta are undertaking a project to demonstrate how coal can be burned cleanly for steam raising in heavy oil operations by using TransAlta's LNS Burner on a steam generator at Esso's Cold Lake Production Project. The $10.7 million project started up in mid-J990, with testing to be completed in mid-I99J. The province of Alberta and Western Economic Diversification Canada, along with other private industry, are contributing funding to the project.The other demonstration project that has been selected for funding under the United States Department of Energy's Innovative Clean Coal Technology Program is a retrofit of LNS Burners to a 33 MW cyclone unit at Southern Illinois Power Cooperative's Marion generating plant. The US$13.6 million project is scheduled for completion 18 months after final funding arrangements are made.TransAlta believes that these demonstrations will lead to the development of a commercial ""clean coal"" technology. Other demonstration projects being planned will further broaden the base of applications.IntroductionTransAlta has recognized an increasing concern worldwide for the environment, and in particular the acid rain problem. Increasing public concern and the need to meet either current or possibly more stringent emission regulations have prompted them to explore various emission reducing technologies - despite the low sulphur content of its coal.The flue gas desulphurization (FOD) and selective catalytic reduction (SCR) technology currently available to reduce sulphur and nitrous oxides from coal burning power plants is very costly. Having to incorporate FGD technology, or ""scrubbers"", greatly adds to the cost of producing power. Having to add such high costs to electric customers' bills is something TransAlta is striving to avoid.There are many research programs now underway which are evaluating ways to provide electricity from coal in a clean manner. TransAlta has been observing or participating in a variety of these programs. However, there is one new technology which the company has identified as having the potential to control acid rain causing emissions at a fraction of the cost of conventional systems. That technology is called Low NOx/SOx, Burner - or LNS Burner."

Jan 1, 1990

By V. A. Preto

The Rexspar uranium deposit is located approximately 5 kilometres south of Birch Island, B.C. Three separate zones of commercial-grade uranium mineralization mineable by open pit have been outlined. Uranium and fluorite-celestite mineralization occur in a trachytic member of alkali-feldspar porphyry, lithic tuff, tuff breccias and pyritic schist conformably interlayered with a succession of strongly deformed greenschists and fragmental rocks that are, in large part at least, of volcanic origin. The age of these strata is not precisely known, but they are considered as part of the possibly Mississippian Eagle Bay Formation. Commercial-grade uranium mineralization is always associated with fluorphlogopite-pyrite replacement of the trachytic unit and is contiguous to, but separate from , a zone of ore-grade fluorite mineralization. In all zones, ore occurs in lenses of variable thickness and lateral extent, which lie parallel to the schistosity of the trachytic rocks and surrounding greenschists. The principal radioactive minerals at Rexspar have been identified by other workers as uraninite, uranothorite, bastnaesite, torbernite and metatorbernite. Considerable amounts of thorium oxide and widespread rare earths have been reported from all three radioactive zones. The geology of the deposit suggests that the trachytic rocks represent a highly differentiated intrusive-extrusive system in which fluorphlogopite, pyrite, fluorite and uranium-bearing minerals were deposited late in the evolution of the system by deuteric, volatile-rich fluids. The considerable amounts of thorium and widespread rare earths associated with the uranium tend to support the thesis that this element is of primary origin rather than secondary.

Jan 1, 1978

By T. H. Etsell, P. Kerr, Qi Liu

"The objective of this investigation was to study the reaction mechanisms during the reduction of iron oxides in the presence of calcium chloride and carbon black as a simplified iron segregation process. The gas phase was analyzed by mass spectroscopy and the solid reaction products were analyzed by scanning electron microscopy. Mass spectroscopy, combined with thermogravimetric analysis and differential scanning calorimetry, revealed the presence of several gases at elevated temperatures over time, and the scanning electron microscope in combination with energy dispersive X-ray analysis illustrated the growth of a metallic iron phase on or near the carbon substrate. The results correlated well with similar copper and nickel segregation processes, but also introduced new insights that challenge the simplicity of the current models. The formation and transport of gaseous iron species to the carbon substrate in the presence of steam and hydrogen were evident during the reduction process that was studied; however, there is more happening at a mineralogical level, based on evidence of a liquid phase resulting in substantial growth due to an apparent fluxing effect created by the calcium chloride.These results help to better explain the chemical reactions and, in turn, the thermodynamics and kinetics of iron segregation processes related to the beneficiation of low grade complex iron ores. The results are also applicable to the production of metallic iron and concentrated titanium dioxide from ilmenite ores. The benefit of this process is that it allows ores in which the iron minerals are intimately associated with gangue minerals to be processed in circumstances where conventional mineral processing techniques are unsuitable or incapable of upgrading the material."

Jan 1, 2016

By J. F. Wright

During the last three years prospecting has been active in southeastern Manitoba and a number of interesting gold, nickel and copper deposits have been discovered within an area 90 miles north of the international boundary, and extending about 40 miles westerly from between mileage 60 and 110 on the Manitoba-Ontario boundary. As known at present, two-thirds of this area of 2,000 square miles is underlain by pre Cambrian granite and granite gneiss and is not likely to contain mineral deposits of economic importance. The remaining one-third is underlain by metamorphosed sediments and lavas (greenstones), penetrated by the granite and granite gneiss and, at various localities, cut by bosses, sills, or dykes of gabbro, diorite, granodiorite, and other types of intrusives. The nickel, copper, and gold mineralization accompanied or followed the intrusion of these different rock types. The gold deposits are limited in distribution, so far as known, to the northern part of this prospecting area and occur along Manigotagan and Wanipigow rivers. These deposits have recently been described in some detail, (3) and therefore only the copper and copper-nickel deposits of the southern part of this area, along Oiseau and Maskwa rivers, will be described in this paper.

Jan 1, 1925

By A. A. McDonald

Anode casting has been in operation for two years in Hudson Bay Mining and Smelting's Flin Flon smelter. The new plant allows all casting to be done on one shift and so achieves considerable labour savings. The equipment and operations are described. Some important features are as follows: very consistent anode weights by the use of the load-cell controlled casting ladle; excellent mould life ; very low reject rate; and trouble-free take -off tower. Some of the start-up problems are described and an outline is given of the main operator functions. Data on labour, propane and maintenance costs are presented.

Jan 1, 1977

The effect of superficial gas rate distribution (Jg profile) on down-the-bank metallurgical response was tested in the rougher-scavenger bank (eight 10-m3 tank cells, 4 roughers and 4 scavengers) at Highland Valley Copper Mine's Cu/Mo separation circuit. Three Jg profiles were tested: (a) as found (i.e., typical practice), (b) increasing decreasing (i.e., increasing from cell 1 to 4 and decreasing from cell 5 to 8), and (c) decreasing-increasing (i.e., decreasing from cell 1 to 4 and increasing from cell 5 to 8). The Jg profile approach proved to be of considerable value. Profile (b) gave the best metallurgical results, i.e., the highest down-the-bank grade/recovery (increase in grade at constant recovery was approx. 3-4% compared to the as found case) and the most efficient Cu/Mo separation (cumulative Cu recovery was reduced by almost half - approx. from 20% to 12%, at 99% Mo recovery). The success of the evaluation prompted the implementation of profile (b). Detailed gas dispersion characterization tests (Jg and Db (bubble size)) showed significant discrepancies between the Jg measured directly (using the McGill University sensor) and the Jg calculated from field instrument readings (volumetric gas flowmeter) and machine dimensions (cell cross-sectional area). Tests were designed to reveal the source of disagreement. It was observed that a significant number of bubbles were not able to float (i.e., they were entrained with the tailings), the evidence appearing to be a significant number of very small bubbles (approx. 200-300 µm) which did not have sufficient buoyancy to rise. Consequently, rather than relying on the field instrument, the evaluation depended on the McGill University Jg sensor, which collects bubbles in a tube near the pulp-froth interface, thus providing significance to the data as the measurements were obtained from bubbles that almost certainly floated.

Jan 1, 2007