Search Documents

By F. S. Hoseinian, M. Irannajad, M. Safari

In this study, the effect of chemical interactions of materials used in ion flotation on the removal of Ni(II) ions from low concentration synthetic wastewater was studied. Sodium dodecyl sulfate (SDS) and ethylhexadecyldimethylammonium bromide (EHDABr) as collectors and methyl isobutyl carbonyl (MIBC) and Dowfroth250 as frothers were used. To investigate the effective parameters and interactions of them, 16 experiments including 6 level variables were performed by supporting DX7 software and on the bases of 2-level factorial method. In the first step, the tests were conducted in a Hallimond tube. The result showed that collector of SDS and frother of Dowfroth 250 had appropriate interaction with each other at pH = 3. In the second step, optimal results from the first step were evaluated in a mechanical flotation cell. The removal of Ni(II) ions increased by increasing the time of flotation and they have a direct relation with the water removal. The kinetics study shows that the order and the rate of removal of the reaction do not follow any of the zero-order, first-order and second-order equations. The flotation rate curve on the removal of Ni(II) ions will divide the separation process to two stages, a fast flotation rate at the first stage and a slow flotation rate at the second stage. Ni(II) ions removal was obtained 88% at the best condition.This study showed that the use of ion flotation was a very effective method for Ni(II) ion removal from industrial wastewaters.

Jan 1, 2016

By J. J. Brummer

"A reconnaissance geochemical survey, using the stream sediment technique, is described. The survey covered an area of about 400 square miles, in the Seal Lake area of central Labrador, underlain by basaltic flows, diabase and metadiabase sills, and sedimentary rocks. Previous work had indicated numerous small copper occurrences within the Seal Lake group of rocks. Stream sediments were tested for the readily extractable copper content and total heavy metal content. The results of the copper survey did not yield any new data on the distribution of copper mineralization. Results of the total heavy metal survey attracted attention to a remote portion of the area (Ten Mile Lake), which had hitherto been regarded as having no economic interest. The anomalous values found, suggested that zinc mineralization should occur in this region. Geological mapping indicated that the rocks exposed belonged to the Letitia Lake Group, which is older than the Seal Lake Group exposed to the east, which contains the copper mineralization of the district.Investigation of the area lead to the discovery of: (1) uneconomic lead-zinc mineralization; (2) radioactivity extending over a considerable area. Evaluation of the radioactive rocks led to the discovery of columbium-thorium mineralization in amphibolite and in diopside-actinolite schists along a contact with intrusive alkali syenite.Thus a geochemical survey, which was planned to evaluate a copper province, resulted in the discovery of lead-zinc-columbium-thorium mineralization."

Jan 1, 1960

By James F. A. Hatley

Northern Saskatchewan comprises an area of about 350 000 km2 and boasts some of the world's largest known high-grade uranium deposits. The successful mining of these deposits, however, can not be accomplished without overcoming technical challenges. Not only is the high grade of the uranium ore challenging, but mining methods need to be developed to deal with groundwater at very high pressures, and ground conditions that vary substantially from excellent to wholly unconsolidated clays and sand. This paper discusses the various mechanisms of inflows at the three of the Cameco Corporation Mines in Northern Saskatchewan. The risk of inflows is quantified in terms of unique challenges from hydrogeologic conditions, rockmass integrity, and uncertainty in geologic conditions. Mitigation strategies in case of an inflow are also briefly described. The paper concludes by addressing the impact of institutional rules (corporate standards) on minimizing, monitoring, and controlling the probability and/or impact of unexpected inflows.

Aug 1, 2010

By S. McAlister

"Falcon Concentrators Inc. has developed a high capacity centrifuge for the recovery of fine, free gold as well as other metals and minerals which were previously thought to be unrecoverable by gravity means. Development started in the early 1980's and the first commercial operation was commissioned in 1986. Gold applications include scavenging conventional gravity and cyanidation circuit tailings, cleaning gravity concentrates, cleaning flotation concentrates to melting grade, scavenging flotation tailings, and placer mining. Recent development work by Falcon has expanded the applications scope of the centrifugal concentrator to include many minerals amenable to gravity concentration including iron, tin, industrial minerals, and hazardous wastes. This paper discusses this technology including its history, present applications, and future potential. OVERVIEW OF CENTRIFIJGAL CONCENTRATIONUsing centrifugal force to enhance the separation of materials by differential specific gravity has been researched for over a century. Many attempts have been made to concentrate minerals in high gravity fields. Patents were granted on this subject as early as 1891 (see Figure 1). Patenting activity continued into the 1920's and has been relatively quiet since. It is significant that no centrifugal system of gravity concentration has been broadly accepted by the mineral processing community until recently. Much of the world's reserve of mineral deposits which are amenable to conventional gravity concentration technology (coarse-grained) have been mined and therefore there is an increasing demand for technology which can economically recover the fine-grained gravity recoverable minerals in the remaining deposits. In addition, centrifugal concentration can play an increasing role in solving environmental problems by offering an inexpensive method of concentrating hazardous materials such as uranium, plutonium, mercury, lead, and other heavy metals. The overall cost of disposing of these substances safely can be drastically reduced if they are recovered into a concentrated form prior to disposal."

Jan 1, 1992

By X. J. Luo, F. Zhang

"Metallurgical slag (MS) such as steel slag, copper slag is a renewable resource and its compressive strength exceeds 200MPa in general. Because pure metal slug can easily be mixed into MS, complex recycle system is necessary in order to realize MS’s recycling. Meanwhile, there is high equipment failure rate in conventional crushing system. New crushing systems with inertial cone crusher could solve this problem very well. Recovery rate of MS tailings requires that crushing product can’t contain too much oversize product, so the essential equipment include two crushers and one sieve in the traditional crushing system. The new crushing system which only includes two crushers can meet the requirement and simplify the crush process. Investment of crushing equipment and infrastructure can be cut down. Operating and maintenance costs can be obviously reduced due to the simple process, which also could achieve high energy saving and excellent economic efficiency.INTRODUCTIONMetallurgical Slag (MS) such as steel slag, copper slag is a typical industrial solid waste and it threatens our environment’s safe. Metallurgical enterprises must take action to settle these wastes in order to protect our environment. Because pure metal slug can easily be mixed into MS, its uniaxial compressive strength (UCS) will exceed 200Mpa. If crushing station employs traditional crushing equipment, equipment failure will be easily caused because of these pure metal slugs. Coarse crushing equipment usually adapts jaw crusher in traditional Crushing technology and rod mill will be utilized to finish the secondary and fine crushing works. And the same time screening machinery should be used to ensure the suitable particle size (Figure 1)."

Jan 1, 2016

By T. L. Sadlier-Brown, Andrew E. Nevin

"Common properties of commercial geothermal steam reservoirs are a magmatic heat source, the presence of water in vapour and liquid phases, and a surrounding seal of low permeability. The latter may be due to a combination of hydrologic load, argillic alteration and mineral precipitates. The temperature and pressure of vapour and liquid co-existing in equilibrium at maximum enthalpy may approximate 451°F and 450 psi. Steam reservoirs do not necessarily vent steam, but fluid which breaches and mixes with meteoric waters may emerge as hot springs. A systematic exploration program in Western Canada would involve a sequence of four stages utilizing geological, geochemical and geophysical techniques. The geochemical parameters of hot spring waters, such as silica, lithium and potassium content, give some indication of the basic reservoir temperature. The geology of Quaternary volcanics, including reservoir rocks, structure and rock alteration, is of prime importance. The costs of preliminary indirect methods are no more than those of oil and gas exploration; however, high temperatures compound drilling problems and costs. Exploration expenditures of twenty million dollars or so might be needed for a significant discovery. British Columbia and the Yukon Territory contain abundant Cenozoic volcanic rocks and over 50 thermal spring complexes (some with as many as 20 springs in one complex). Six regions are tentatively picked for exploration. Four regions coincide geographically with post-1980 electric power facilities and loads, and with possible alternatives such as potential dam sites. The Lillooet River region, Terrace region and Western Vancouver Island region have inferred potential for the existence of a plus-500-Mw geothermal reservoir. The Kootenay region may or may not have such potential. The Stikine River region has strong evidence of geothermal endowment, but the anticipated power market of the middle future might be only 30-50 Mw. The Whitehorse, Y.T., and Atlin, B.C., region has a belt of thermal springs and Recent cinder cones. The anticipated middle-future needs are real enough, but in absolute terms they are small, say 20-30 Mw. Legislation and policy on geothermal resource rights are lacking in British Columbia and the Yukon Territory at this time. As well as making policy, governmental organizations will play a significant role in geothermal development as buyers of steam or electricity. The role of industry is visualized as assuming the high-cost and high-risk exploration effort, provided the nature of this effort is understood by government."

Jan 1, 1973

By John Starkey

This paper examines 5 years of SAGDesign testing data with particular emphasis on the grinding test results from two recent projects, the Fortune Minerals Limited NICO project, and the Aurora Energy Resources Inc., Michelin deposits, located in the Northwest Territories and in Labrador respectively. The context is to compare these results with the SAGDesign database. The required SAG mill pinion energy for these two ores showed vast differences, even though both ores had similar average Bond Ball Mill Work Index values - about 13 kWh/t each for the two deposits respectively. Bond Rod Mill Work Index values for NICO ranged up to 19.7 kWh/t for the hardest ore, confirming the harder nature of the coarse material. SAG mill pinion energy to grind the NICO cobalt-gold-bismuth-copper ore from F80 152 mm to T80 1.7mm varied from 16 to 35 kWh/t, while for Michelin uranium ore, it varied from 2 to 9 kWh/t. NICO ore is harder than any other material encountered to date using SAGDesign testing. SAG pinion energy is more than double the ball mill pinion energy using a transfer size T80 of 1.7mm and a final grind P80 of 74 microns. For NICO, the ore is ?off the charts? for simulation design techniques because there is no comparable operating SAG mill treating ore that is this macro-competent. For Aurora, the relationship between SAG and ball mill pinion energy is reversed in that the SAG mill requires less than half of the ball mill pinion energy using a transfer size T80 of 1.7mm and a final grind P80 of 90?. Because these discoveries are so important for grinding mill design, their impact will be dealt with in future papers, at the August METSOC Conference in Sudbury, and at the September SME Workshop in Tucson. It has now been concluded that the ratio of SAG pinion energy to Bond Ball Mill Work Index, is valuable data to use in designing a SAG/ball mill grinding circuit, to help choose the power split needed.

May 1, 2009

Operationalizing the Ruggie Framework in a Mining Context Ruggie?s 3 Pillars: The State?s duty to Protect Policies, regulation, adjudication The Corporation?s responsibility to respect Acting with due diligence to avoid infringing Addressing adverse impacts when involved in abuses Access to Remedy ??even the most concerted efforts cannot prevent all abuse.?

May 1, 2013

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By Sibabrata Patnayak

A major problem during shovel excavation in oil sand mining is the variability of material diggability resulting in varying mechanical energy input, cycle time, energy consumption, wear, and stress loading of shovel dipper-andtooth assembly. This variability greatly influences the mining equipment performance. Different approaches such as empirical ground classification systems, analytical methods, and performance monitoring that are used to determine diggability of groundmass are reviewed. It is concluded that the existing empirical diggability classification systems are site specific and mostly based on rock and therefore, cannot be used for shovel excavation in oil sands. The O&K wedge test is a simple and useful index test for establishing correlations between cutting resistance and geotechnical properties of coal and other soft rock overburden material. But this test, when performed on small size unconfined oil sand samples, may not give reliable indication of diggability because of the boundary conditions on the specimens. Digging predictions made using analytical and laboratory digging models need to be verified with performance monitoring data to better understand the digging effort in oil sands.

Apr 1, 2005

By Inga Tuzovskaya1i

Three types of gold species were observed for gold-zeolites, prepared by reduction of ionexchanged Au species in a series of zeolites: (i) Au3+cations, (ii) neutral Au0 n or charged Aus+ n clusters suggested to be inside the zeolite channels, (iii) Au nanoparticles with diameter varied from 2 through 20 nm located on the external surface of zeolite microcrystals. Contribution of the gold species formed in zeolite after the ion exchange was found to depend on zeolite type, acidity of zeolite, temperature of reduction and time of storage of the exchanged and reduced Au-containing zeolites. Au3+ ionic species and clusters Aun were formed after the ion-exchange procedure (in contrast with the familiar production of Agn in same zeolites). Gold nanoparticles were observed only as the result of reduction of the Au-exchanged forms at elevated temperatures due to reduction of Au3+ species and aggregation of clusters.

Oct 1, 2003

By Helen Shang, Jianjun He

In nickel and copper production, sulfur dioxide (SO2) is generated during mineral smelting. Emission of sulfur dioxide into the atmosphere causes serious health and environment issues. Sulfuric acid plants, which convert the harmful SO2 gas to commercially useful sulfuric acid product, ensures safe and environmentally sound smelter operations. The sulfuric acid plant is mainly composed of a SO2 to SO3 converter, a series of heat exchangers and SO3 absorption towers. The SO2 converter is crucial for minimizing SO2 emission in a smelter. In this paper, steady state and dynamic modelling are carried out for the converter using mole and energy conservations. Simulations are performed to investigate the effect of feed conditions on SO2 conversion. The developed model represents an important component for modelling the acid plant in a smelter and is expected to provide a fundamental tool for the future optimization and control development.

Jan 1, 2014

By Richard P. Curtin, John M. Goris, Lewis A. Martin

Cable bolt supports are being recognized as an effective ground control system in under-ground coal mines in North America, and their use has increased considerably during the past few years. The U.S. Bureau of Mines personnel are conducting both laboratory and field tests to evaluate the performance of these supports under a variety of conditions and to establish realistic design guidelines. This paper describes efforts to evaluate the capability of cable bolts to resist the high shear forces often present in longwall operations. Shear tests were conducted on pairs of 0.025 m3 (0.88 cu. ft) concrete blocks having joint surfaces ranging from rough to smooth. Tests were conducted on blocks both with and without reinforcement with 15.2 mm (0.6 in.) diameter steel cables. During each shear test, the loads and displacements along the normal and shear axes, as well as loads on the cable, were monitored. Cableloads were determined using strain gauges attached to the outside surfaces of the barrel-and-wedge anchors used for pretensioning the cables. Test results show that a cable bolt placed across a joint more than doubled shear resistance of shear blocks having both smooth and rough joints.

Jan 1, 1996

By A. Jafarnia

Aluminum alloys are frequently grain refined during solidification in order to promote the formation of an equiaxed grain structure in the casting. The application of Ti-based grain refiners and/or Ti containing master alloys for improving mechanical properties may result in formation of Al-Ti based intermetallics. Although the grain refinement produces many desirable qualities in aluminum castings such as improved castability and mechanical properties, the addition of Ti to Al-Si foundry alloys may lead to the formation of some undesirable intermetallic particles such as AlTiSi and cause a number of operational problems such as nozzle blockage due to segregation and agglomeration of aluminide particles within the nozzle. There are several questions to be clarified when minor amount of Ti is added to Al-Si alloys. They include nucleation and growth of AlTiSi particles, their morphologies and orientation relationships with aluminum matrix and the dissolution of these intermetallics during the course of solidification and/or post solidification treatments. The current study was initiated to study the process and possible mechanism of aluminide dissolution and the related phenomena such as segregation and agglomeration. It reports the results found during reheating of laboratory prepared Ti-added A356 alloy at three temperature ranges of below solidus, mushy zone and above liquidus.

Jan 1, 2004

By R. C. Bryce, G. S. Martin

"Aur Resources Inc. is the operator of the Louvicourt Mine located 40 km east of Val d'Or. Quebec. Les Entreprises Minieres Redpath Limitée a member of the 1.S. Redpath Group of companies was contracted to construct two vertical mine shaft collars in deep overburden.During the spring of1991 two vertical shaft collars were established in wet, running sand that was in excess of20 m deep. This paper will illustrate the engineering and construction techniques used in establishing these collars and the methods used to overcome the various obstacles that occurred during construction.IntroductionThe Louvicourt copper/zinc/gold/silver deposit is located 40 km east of Val d'Or, Quebec, is adjacent to the former Louvern Mine which operated at depths of 40 m to 850 m below surface (Fig. 1). This deposit was discovered in mid-1989 as the result of systematic exploration and diamond drilling based on a geological model. The Louvicourt project is operated by Aur Resources Inc.The property is being developed to produce 4000 tid with an anticipated life of just over 17 years. Mill start up is scheduled for July 1. 1994, commercial production October I, 1994, and full production by late 1995. The current production plan provides for 24 040 (XX) t averaging 3.89% copper, 1.95070 zinc, 0.039 oz gold per tonne and 0.99 oz silver per tonne, to be mined."

Jan 1, 1994

By F. R. Ploeger, J. H. Crocket

"IntroductionRocks in the Kirkland Lake district form part of the Timiskaming Group, a south-facing homoclinal sequence of wackes, conglomerate, trachytic flows and pyroclastic rocks and syenitic intrusive rocks. Hewitt (1963) indicates that the thickest section, about 5 km, of the Timiskaming Group rocks is attained in Lebel Township. Several writers (Thomson, 1948; Hewitt, 1963; Hyde, 1978; Jensen, 1978; and Downes, 1979) have observed that the Timiskaming Group unconformably overlies the Keewatin volcanics, particularly along the northern contact. Recent work by Downes (1979) in McGarry and McVittie townships to the east of Kirkland Lake has shown that much of what had formerly been classified as Timiskaming actually belongs to an older group of rocks, the Larder Lake Group (Jensen 1978).General GeologyA series of fluviatile, braided-stream sedimentary rocks (Hyde, 1978) form the oldest of the three major rock suites at Kirkland Lake. Conglomerates constitute a large proportion of these sedimentary rocks and typically contain a large percentage of a variety of locally derived alkalic rock clasts as well as the distinctive red jasper iron-formation pebbles (Fig. 1a). The associated wacke units can be massive to finely bedded and are interbedded with the conglomerate. They also contain a large alkalic tuffaceous component.Interbedded with these sedimentary rocks are alkalic extrusive rocks, including tuffs, agglomerates, breccias and flows, which represent episodes of fissure and explosive crater eruption (Cooke and Moorhouse, 1969). The tuffs, although dominantly alkalic in composition, are commonly reworked and contain sedimentary features such as graded bedding, scouring and crossbedding (Fig. 1 b). The trachytic flows are massive to porphyritic and outcrop mainly east of Kirkland Lake in the adjoining townships. Altered leucitic porphyritic flows, locally referred to as red and green spotted trachytes, commonly occur."

Jan 1, 1982

By Oscar F. Tangel

This paper outlines Canada's current status in world iron ore markets, and evaluates the prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada's major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada's major competitors in these latter three market areas are briefly discussed.

Jan 1, 1966

By T. Kawai

Japan Oil, Gas and Metals National Corporation (JOGMEC) has started an exploration program for Seafloor Massive Sulfides (SMS) in the EEZ of Japan, and launched an investigation program for mining, processing and environmental impact on SMS development. With regard to the mining aspect, the mining system consists of three units: a mining unit on the sea floor, an ore lift-up unit to surface, and a mining support vessel unit which has an ore unloading system that unloads onto a shuttle ship. Regarding the mining unit, JOGMEC and certain Japanese mining and machinery companies developed two types of state of the art mining testing tools. Excavation tests on the actual SMS site in the Okinawa Trough, south-west of Japan, were conducted in 2012. In these tests, the functions of the testing tools, such as cutting ore, moving on the seafloor and climbing up slopes having steeper than a 25 degree gradient, were confirmed. The physical characteristics of the ore, which are key parameters for establishing a mining system, are yet to be fully understood as the exploration program has been undertaken simultaneously. Hence, those examinations have been carried out by ground cutting experiments, analysis of drilling core data, and the like. This paper describes the outline of a proposed mining system, mining testing tools and results of the on-site mining testing.

Aug 1, 2013

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979