Search Documents

By Tony Lipiec, Chris Fleming, Larry Urbanoski

In 2009, the Canadian Mineral Processors (CMP) became aware that Canadian securities regulators were amending the contents of National Instrument 43-101. NI 43-101 is a set of regulations which establish how ore resources and reserves are presented to the investing public. The documents produced under NI 43-101 are central to the ability of many companies to raise financing for their projects. With the increase of metallurgical complexity, and decrease of head grades encountered in new deposits, the role of the Qualified Person (QP) in determining process performance has become increasingly critical in determining the classification category of resources and reserves. Given the challenges confronted by those involved in defining the concentration and extraction of minerals and metals, there is a need to provide support to these QPs. To address these concerns, the CMP established a sub-committee in 2010 to create a set of guideline documents to assist the QP involved in process matters as to what should be included at the various levels of study supporting the establishment of resources and reserves in NI 43- 101. The results of the sub-committee work are presented and the considerations in the writing of the documents are discussed.

Jan 1, 2011

By Jean-Paul Drolet

"The ultimate aim of the Law of the Sea Conference, held under the auspices of the United Nations, is to ensure that all aspects of the use of the sea are covered by international law. The question facing the nations of the world can be stated as: "" Who will control and benefit from the use and the wealth of the sea?""The United Nations Conference on Law of the Sea - known as UNCLOS - which reconvened in New York during the latter part of August 1978 was the third such Conference in the UN's history. The concepts of sovereignty over the territorial sea and freedom on the high seas have remained fundamental to the international law o f the sea until our time. The legal regime based on these two concepts developed initially from state practice meant that the unilateral actions taken by one or more countries were eventually accepted and followed by others.It was not until 1958, during the first Geneva Conference on the Law of the Sea (pursued in a second Conference in 1960) that the Law of the Sea was codified and modified to a certain extent by the then independent nations of the world in the four multilateral conventions on territorial sea and contiguous zone, continental shelf, high seas, and fishing and conservation of living resources.A third Conference got under way many years later when the members of the UN met in New York at the end of 1973 for preliminary discussions . This meeting stemmed largely from the need to fill gaps in existing international legislation which did not cover the new uses of the sea. The Conference was subsequently reconvened a number of times - in Caracas (1974), in Geneva (1975) and twice in New York (1976) for what was called "" substantive negotiating sessions."" A sixth session was held in New York in 1977; a seventh, held in Geneva at the beginning of 1978, recessed and reconvened in New York at the end of August 1978. This is what is referred to, in international jargon, as the seventh session of the Third United Nations Conference on the Law o f the Sea. The following dates are the principal markers of a saga which began some twenty years ago with the purpose of regulating the use of the oceans."

Jan 1, 1981

By B. C. Jago, H. Derbuch

"The Freightrain kimberlite is located on the Brodeur Peninsula, Baffin Island, Nunavut. Twin Mining is exploring the pipe and adjacent land (79 claims/655 km2) using a combination of airborne geophysics, soil sampling, diamond drilling, trenching and bulk sample processing. The pipe originally was discovered by Cominco Limited in 1975, re-evaluated in 1993 by Lumina Investment Corporation, when it was staked as the Zulu pipe, and subsequently covered by three claims in 1998 by Helix Resources who called it Freightrain.The Freightrain pipe coincides with a strong, ovoid-shaped aeromagnetic anomaly. It is the only surface exposure of kimberlite within a 30 km long linear trend of fourteen aeromagnetic anomalies that are up to 600 m in diameter.The pipe is exposed in the crater facies, near the transition into diatreme facies as indicated by the occurrence of pyroclastic kimberlite characterized by abundant olivine macrocrysts, juvenile lapilli and kimberlite autoliths set in a serpentine-calcite matrix. Olivine, Cr-pyrope garnet and chromite are the most abundant macrocrysts; clinopyroxene, ilmenite and phlogopite mica occur in minor to trace amounts. Garnet and chromite harzburgite, garnet lherzolite, garnet-spinel lherzolite and rare eclogite dominate the xenolith population.Garnet and chromite mineral chemistry indicate encouraging diamond prospectivity and that potentially diamondiferous garnet and chromite harzburgite were the principal sources of diamond in the mantle at the time of kimberlite eruption.Single clinopyroxene grains define an ~42 mW/m2 sub-continental geotherm that is rooted in the diamond stability field. This compares to a slightly hotter geotherm (~48 mW/m2) for adjacent Somerset Island kimberlites with an origin in the graphite stability field. This data accords with the general lack of sub-calcic Cr-pyrope garnet, diamond inclusion chromite and diamond in Somerset Island kimberlites."

Jan 1, 2002

By J. F. Nie

Mechanical properties of precipitation hardenable magnesium alloys depend critically on the chemistry, structure, morphology, orientation and distribution of strengthening precipitates. It is therefore important to gain an improved understanding of these information and their correlations with mechanical properties. Our recent studies indicate that additions of 1-2 wt% of Zn to a Mg-6wt%Gd alloy result in a substantial enhancement in precipitation hardening and in creep resistance. If the strength and creep resistance of the resulting ternary alloy are to be further enhanced for commercial applications, then a detailed characterisation of the strengthening precipitates in these alloys is required. In the present study, the precipitates formed in a Mg-6Gd-1Zn-0.6Zr (wt%) alloy, peaked aged at 250°C, have been characterised in detail using transmission electron microscopy and 3-dimensional atom probe field-ion microscopy. It is found the peak-aged microstructure contains a dense and uniform distribution of precipitate plates that form on the basal plane of the matrix phase and are typically less than 1 nm in thickness. Detailed analyses of the structure and composition of these basal precipitate plates will be presented and discussed in the context of previous work on other Mg-RE¬Zn alloys of similar compositions.

Jan 1, 2006

By Rui Wang, Engang Wang, En Jiang, Anyuan Deng, Xingwu Zhang, Fei Wang

In this paper, the rectangular strands of Incoloy 800 superalloy were fabricated with a pilot vertical continuous caster in Northeastern University, China. In the processing, an electromagnetic stirring (EMS) is applied on the secondary cooling zone to control the solidifying structure and segregation of elements in the strands. The solidification structure of Incoloy 800 superalloy strands were investigated at different electric parameters and casting parameters. The research results show that the EMS can effectively restrain the dendrite growth and increase the ratio of equiaxed grains in Incoloy 800 superalloy strands as applied a suitable electric parameters and cooling condition in the process of continuous casting. The evolution of dendrite crystallization in Incoloy 800 alloy strands from the surface to its center during the solidifying process was investigated with and without EMS.

Jan 1, 2014

By William M. Luff

"The Bathurst area has recorded mining production as early as 1837, although the bulk of the production has come in recent years. Production has been mainly from the well-known massive sulphide deposits, but vein, gossan, and a variety of other deposits have also been mined. This paper summarizes the history of the mined deposits, along with tonnages and grades produced. A number of ""firsts"" have been noted in the Bathurst area. The A Zone deposit, located in the Heath Steele area, was the first in the world discovered using airborne electromagnetic methods. Heap leaching of gold from the gossan zone at Caribou was the first operation of its kind in Canada. The Keymet mine was the first base metal (lead-zinc) mine in New Brunswick. For the past few years, the Brunswick No. 12 mine has been one of the largest zinc mines in the world.IntroductionThe Bathurst area (Fig. 1) first had mining production in 1837 when copper was mined from a deposit on the Nepisiquit river (MacKenzie, 1958). The majority of the production, however, has been in recent years from massive sulphide deposits, but there are also other significant operations. . Table 1 is a summary of Bathurst area mineral production, showing concentrator feed tonnages and mill feed grades. The table does not include peat deposits, sand and gravel, dimension stone or rock quarries. Figure I is a general geology map of the Bathurst area, indicating deposit locations. The deposits are divided into four categories: massive sulphide, vein, gossan and other. The deposits in each category are described in chronological order of exploitation."

Jan 1, 1995

By William M. Luff

"The Bathurst area has recorded mining production as early as 1837, although the bulk of the production has come in recent years. Production has been mainly from the well-known massive sulphide deposits, but vein, gossan, and a variety of other deposits have also been mined. This paper summarizes the history of the mined deposits, along with tonnages and grades produced.A number of ""firsts"" have been noted in the Bathurst area. The A Zone deposit, located in the Heath Steele area, was the first in the world discovered using airborne electromagnetic methods. Heap leaching of gold from the gossan zone at Caribou was the first operation of its kind in Canada. The Keymet mine was the first base metal (lead-zinc) mine in New Brunswick. For the past few years, the Brunswick No. 12 mine has been one of the largest zinc mines in the world.IntroductionThe Bathurst area (Fig. I) first had mining production in 1837 when copper was mined from a deposit on the Nepisiquit river (MacKenzie, 1958). The majority of the production, however, has been in recent years from massive sulphide deposits, but there are also other significant operations.Table I is a summary of Bathurst area mineral production, showing concentrator feed tonnages and mill feed grades. The table does not include peat deposits, sand and gravel, dimension stone or rock quarries. Figure I is a general geology map of the Bathurst area, indicating deposit locations. The deposits are divided into four categories: massive sulphide, vein, gossan and other. The deposits in each category are described in chronological order of exploitation."

Jan 1, 1995

By Kaiwen Xia, Bibhu Mohanty, Per Svedensten, Sheng Huang

"The mechanics of crushing and grinding operations in mining and excavation processes has been investigated in a laboratory simulation study. It employs a multi-particle bedded rock target, which is subjected to multiple impacts. The impact set-up consists of a Hopkinson pressure bar and a Piston-holder system. The apparatus, employing a 38 mm diameter pressure bar, was used to apply varying but calibrated dynamic loading force on the rock particles. The energy consumed by the sample during fragmentation was determined by considering the energy carried by the incident wave and the reflected wave. The Pistonholder system is used to hold rock samples and to recycle fragments after each test for particle size analysis, for single as well as multiple impacts. The feed size selected was in the range of 9.5 to 12.7 mm for all rock samples, and the impact velocity was set at 14 m/s. Two strong granitic rocks and a relatively weak limestone were the target rocks. The resulting particle size distribution after each set of impacts, ranging from single to 10 consecutive impacts, were analyzed, and various size distribution functions (i.e. Rosin- Rammler, Swebrec, Grady and Gilvarry functions) were fitted to compare their suitability in predicting the fragment size distribution for each rock type. INTRODUCTIONCrushers are widely used in the mining industry all over the world. Understanding fragmentation behaviour of rock under crushing process is fundamental to improved productivity and efficiency in mining operations. This is particularly so as all subsequent size reduction processes such as crushing and grinding are far more energy intensive than the initial blasting process employed in breaking of in situ rock. A considerable body of experimental studies exists on the behaviour of rock crushers for specific rock types in order to aid in the design of various types of crushers. However, these studies are mainly site specific, that is, the results are largely empirical, and the fundamentals of fracture process that lead to size reduction have not been dealt with adequately. Most such studies have attempted to link the input parameters, such as feed size and crusher parameters, with output particle size, and global energy expended in the process. However the physical mechanism of crushing process is still not well understood. First of all, the energy consumed by the rock sample is hard to calculate during standard crushing or grinding tests; secondly, multi-particle test is hard to perform in the laboratory due to irregular shape of the subject rock sample. In This paper, describes a laboratory crushing apparatus for multi-particle rock samples, with sufficient control of the energy expended in the process, with a view to relate creation of new fracture surfaces in the size reduction process."

Jan 1, 2015

By D. Magoon

The metals industry has enjoyed a resurgence in prices and demand for its commodities during the global surge in economic activity that began in 2005. This success has brought with it an unprecedented demand for professionals in all sectors of our economy. Nowhere is that more true than in the mining and metallurgy sectors. However, this welcome improvement follows on the heels of almost two decades of challenging markets for the mining and metallurgy. Our sector's protracted economic slump created a paucity of demand for professionals that had several consequences. Our industry came to be viewed as a low ?tech, uninteresting place to work. Low demand for professionals encouraged students to seek other career options. Reduced demand for graduates, coupled with diminished program funding by our sector, resulted in dramatic shrinkage in university mining and metallurgy programs. This paper explores the lessons to be learned from our recent economic history and discusses some strategies for addressing our image issue. Attracting and retaining good employees is also strongly influenced by a company's reputation and record as a good employer. This reality is very well illustrated by the findings of an international survey undertaken by Towers Perrin in 2005 of 86,000 employees of mid-sized and large companies in 16 countries. The key findings related to attracting and retaining employees are presented. These findings are also discussed in the context of their specific applicability to the mining and metallurgy industry.

Jan 1, 2007

By Louise Corriveau, Bronwyn Azar, Valerie A. Jackson, Luke Ootes, Jeff Harris

We use the results of new bedrock mapping, combined with geochemical point data and airborne radiometric data (in particular equivalent uranium concentrations) to help determine which geological units in the Paleoproterozoic Great Bear magmatic zone (GBmz) contain elevated uranium. The data collectively indicate that the highest primary uranium concentrations are in equigranular granites and subvolcanic/volcanic porphyries. Notably, these rocks host the majority of known uranium-bearing deposits and/or prospects in the GBmz. We speculate that the uranium in these deposits/prospects was derived from nearby, uranium-enriched rocks and was mobilized by much younger, circulating hydrothermal fluids. Sedimentary rocks of the Thelon and Dismal Lakes groups unconformably overlie the GBmz and are known to host unconformity-type and sandstone-hosted uranium prospects. Most likely, the uraniumenriched rocks of the GBmz acted as a uranium donor to these overlying sedimentary basins. The method of investigation employed in this study may be applicable to other ‘granitic’ terrains in order to identify regions with favourable rocks for uranium exploration.

Jan 1, 2013

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By Rene Cane, V. I. Lakshmanan, John Starkey, Richard May

"The Agrium Kapuskasing Phosphate Operation mines and processes up to 6,000 t/d of phosphate ore. Run-of-mine crushing to minus 6 inches is done in a toothed roll-crusher, while grinding is done in a SAG/ball mill circuit with no coarse recycle classification of the SAG mill discharge. The primary grinding mill is an 18 ft. diameter x 9 ft. EGL, 1500 HP variable speed SAG mill and the secondary mill is a 13 ft. diameter x 21 ft. long, 2000 HP fixed speed, ball mill. When hard ore was treated, the SAG mill restricted the tonnage that could be ground. When soft ore was treated, the ball mill and spiral classifier overloaded and restricted throughput.Recommendations from a plant benchmark and an ore hardness testing program, on how to better utilize installed energy in the Agrium SAG mill when treating soft ore, and how to obtain best results when treating hard ore, were checked in a pilot plant investigation in the 3 ft. diameter Starkey-PRO Pilot SAG Mill. Correlation between the ore hardness testing and the results from the 3’ Pilot SAG mill was very good. In addition, the work indicated the results that could be expected for the different ore types when using either smaller SAG discharge grates and/or a vibrating screen with 10 mesh square opening cloth.INTRODUCTIONAgrium Kapuskasing Phosphate Operation consists of a 6800 t/d open pit mine and a concentrator, near the Town of Kapuskasing in Northern Ontario. The two major ore types are sandy ore and cemented ore. Sandy ore is fine, soft and easy to grind in the SAG mill while cemented ore is harder, more blocky and difficult to grind in the SAG mill. The ratio of sandy to cemented ore in the deposit is thought to be in the order of 80:20 but can range as high as 5050, so it was important for the grinding circuit to have the ability to treat sandy ore alone."

Jan 1, 2002

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002

By A. C. Drost

The mining industry has been put under closer scrutiny in recent years, which has led to the adoption of a plethora of initiatives in countries around the world and by international organizations, some voluntary and others mandatory, governing economic, ethical, social and environmental practices of this industry. In order to plan appropriately, secure project financing, build value and manage risks, it is imperative to identify and understand the application of this new and evolving regime, which can be described under the general label of corporate social responsibility (?CSR?) law, and to incorporate compliance policies into the day-to-day operations of mining companies. Our paper and presentation will describe this new legal framework, which includes both ?soft? law and ?hard? law adopted at the international and domestic level that governs the actions of mining companies, particularly when operating in developing countries. While the notions of hard and soft law may seem abstract and grounded in legal theory, this paper shall demonstrate how these concepts concretely apply to companies in general, and to mining companies in particular. An analysis of the recent case law in this area as well as examples of corporate ?best practices? will illustrate the application of this body of law. As will be demonstrated through the case law, non-compliance of CSR law (both ?soft? law and ?hard? law) can lead to economic penalties, difficulties in accessing capital, loss of social licenses and even the withdrawal of permits and concessions. This confirms that now more than ever, ethics and sustainable practices in mining are fundamental to building a successful business model.

Aug 1, 2013

By K. V. Konigsmann

"Mattagami Lake Mines Ltd operate a zinc-copper mine with an annual output of about 200,000 tons of zinc and 30,000 tons of copper concentrates. Zinc concentrates arc shipped to a company owned smelter in Valleyfield (a distance of 690 miles), for Export to Quebec City and also to Josephtown, Pennsylvania (1,060 miles, Figure 1.)The protection of concentrates in open gondola rail shipments has been a matter of concern since operations commenced. Considerable financial losses did occur at times because of wind erosion. Operating difficulties were also encountered by customers because of excessive moisture accummulation in the concentrates. Test shipments made in 1969 established the magnitude of losses in open cars. The results and subsequent investigations at our mines and elsewhere confirmed that load protection is an economic necessity.Many types of covers were experimented with, more or less successfully. In 1972 we agreed on a joint program with Dupont of Canada Limited. A new type of cover was developed by early 1973. It has been in use since, undergoing several improvements as experience accumulates."

Jan 1, 1975

By Ian Rozier

"Emphasis in recent years in western Canada has been placed on the development of large open-pit coal mines, the most notable developments being in northeast British Columbia. However, vast resources exist below the limit of economic open-pit mining, and with world demand predictions of the late seventies in mind, the potential of underground coal mining in western Canada has been investigated. Particular emphasis has been placed on the Plains coalfield of Alberta, and there is optimism that underground coal mines will be developed in the Lethbridge area of southern Alberta.With no existing operations in southern Alberta with which to compare mining conditions, any mine planning and feasibility level studies rely heavily on the engineering/geotechnical data obtained from surface investigation to predict ground control problems and technical constraints on mining. Such investigations have been integrated with exploration drilling programs. Emphasis has been placed on extracting maximum information to provide an over-all appreciation of potential ground conditions and to identify specific ground control problems that could be encountered.The acquired geotechnical parameters are then used to evaluate the mine properties from an engineering standpoint for input into the determination of optimum mine layouts, development directions, mining methods and roadway and face support requirements. These geotechnical studies have been primarily directed toward the longwall mining method, but the acquired data base could equally be applied to alternative mining methods.In addition to the lithologic and structural controls which relate to roof stability, caving characteristics, floor heave and subsidence, investigations have been directed at gaining an understanding of the over-all surface and ground water regime with respect to potential inflow into the mine openings and ground control problems that could be caused by inflows encountered during mining. Experience has shown that soft floor conditions and water control are important factors to be considered in a longwall layout, and without doubt these parameters will play a major role in the design and operation of a successful longwall operation in the Lethbridge coalfield."

Jan 1, 1986

By Todd S. Harris

"IntroductionThe western region of North America has long been considered a dynamic market supporting such diversified industries as lumber, agriculture, cement, and electronics. In recent years however, the region has also been the focus of a great deal of activity in the extender and filler mineral s business from companies seeking to position themselves to take advantage of the large demand for these materials both here and abroad.Extender and Filler MineralsExtender and filler mineral s include 15different products used in numerous end uses. The nine most important extenders and fillers are listed in Table I. These products range in price from under $50 a ton to over $4,000 a ton and basically represent the following three different types of minerals:Particulate products-Calcium carbonate; Kaolin; Silica.Platy minerals-Talc (Montana, Canada); Mica.Fibrous minerals-Talc (California, Eastern U.S .A.);Wollastonite.What distinguishes these products from other industrial minerals? For one thing, an important feature of extender and filler minerals is that they are used primarily in such consumer non-durable good s as paper, paint, plastics, sealants, and rubber which traditionally do not react as violently to swings in the economic cycle. In addition, these minerals are sold principally on key physical properties, usually brightness, particle size and shape, oil absorption, and hardness. As part of the physical minerals segment of industrial minerals, extenders and fillers are traditionally the most stable group and typically the most profitable. Studies by C.H. Kline over the past decade on extender and filler minerals has revealed historic average profitability (expressed as a percentage on sales) nearly double that of most other industrial mineral s.The demand for these minerals in the western region (Fig. 1), closely follow s the areas of greatest population concentration. These markets include pulp and paper, mainly in the Pacific Northwest, and paint, around Los Angeles and San Fran cisco. Other significant markets for extender and filler minerals in western North America include joint cements, carpet backing, and plastics, mainly PVC pipe."

Jan 1, 1986

By G. Major-Marothy

"INTRODUCTIONA beneficiation plant to upgrade earthy iron ores is being installed by the Iron Ore Company of Canada in Sept-Iles, Quebec.The crude ore for the plant will come from the Knob Lake area, located in Northern Quebec, where mining has been in progress since 1954.Some 170 million tons of ""direct 11 ores have been mined and shipped in the past eighteen years, with an overall silica content of 7 to 8 percent. No beneficiation - except the reduction of the top size to about 2 inches - took place during this period, but extensive research work has been carried out, in order to find a feasible process.Since “washing"", gravity separation, roasting and magnetic separation experiments did not indicate positive enough results, flotation was tried and found to be feasible.The beneficiation complex being installed will consist of grinding, flotation, dewatering - i.e.: thickening, filtering and drying - balling feed preparation, and agglomeration - i.e.: balling and induration.This process will result in a product superior to the ""direct shipping"" ores and will also expand the ore reserves by allowing material with a higher silica content to be utilized.THE OREThe Knob Lake ores are grouped by mineralogical composition and by grade.BLUE ORES, representing roughly two thirds of the reserves, carry their iron content mostly in the form of massive, blue hematite and martite.YELLOW ORES, about one sixth of the reserves, have predominantly hydrated iron oxides as the iron bearing minerals.RED ORES, the other sixth of the reserves, carry the iron mostly in the form of red hematite.The gangue in all ores is mainly quartz, but aluminum oxides and hydroxides are also present, particularly in the red ores."

Jan 1, 1972

By Yuki Tsunazawa, Sho Fukui, Chiharu Tokoro

"A milling process is one of the important unit processes in mineral processing. In the milling process, the control of particle size distribution is necessary for the later physical separation process. Since the milling process is strongly affected by the equipment designs, operation conditions and raw materials, the control for particle size distribution of milling products is mainly based on empirical rules. Recently, the discrete element method (DEM) has been widely used as an effective tool to investigate the behavior of grinding media. Although the behavior of grinding media can be accurately simulated, it is not well-established the way to predict particle size distribution after milling by the DEM simulation.The objective of this study was to develop a new method to predict particle size distribution in ball milling using the DEM simulation. To predict particle size reduction, a correlation between experiments and the simulation was investigated in various operation conditions, that is, wide range of the rotation speed and the filling ratio of grinding media. In experiments, after lime stone was ground, the average and variance of particle size distribution were evaluated using some kinds of distribution equations. In the DEM simulation, direct simulation of particle disintegration in milling process is generally very difficult because of huge computational load. Therefore, collision energy between grinding media balls orgrinding media ball and wall was used as a factor of particle disintegration.As a result, a good correlation between experiments and simulation was obtained. In addition, the particle size distribution in ball milling could be predicted using this correlation. Therefore, these results indicated that the use of the correlation between experiments and the DEM simulation was an effective approach of predicting the particle size distribution in milling process."

Jan 1, 2016

By K. Hashiba, Y. Z. Liang, K. Fukui, M. Koizumi

"Efficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Development and modification of the rock drills based on test data are timeconsuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved. The objective of our research project is to construct a new realistic numerical model of continuous percussive drilling, which is based on the previous Okubo-Nishimatsu’s model. In this study, the parts of the previous model involved in stress wave propagation and attenuation were modified. The two models were prepared for HD712 hydraulic rock drill mounted on crawler drills and HD210 hydraulic rock drill mounted on drilling jumbos. Stress wave propagation was computed with the discretized one-dimensional wave equation. The calculated results were compared to the stress waves measured on a rod during percussive drilling. In both models for HD712 and HD210, the measured stress waves can be reproduced with the one-dimensional model of the same acoustic impedance as the actual piston, shank rod and rod combined with the CI+spring model as a rod joint. The calculated results indicate that the spring constant in the model of a rod joint needs to be set appropriately depending on drilling conditions. INTRODUCTIONEfficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Components related to the percussive drilling are a drill body, a piston, a shank rod, rods, rod joints, a bit and rock. The piston in the drill body is reciprocated by hydraulic pressure and collides with the shank rod a few thousand times per minute. Stress waves generated by the collision propagate and attenuate in the rods and rod joints, and then reach the bit. The bit penetrates and crushes rock. During percussive drilling, the components mutually affect each other and self-induced oscillation occurs. The number of blows and the rate of penetration are determined by the practical drilling conditions such as hydraulic pressure, thrust force, number of rods and mechanical properties of rock. Development and modification of the rock drills based on test data are time-consuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved."

Jan 1, 2015