Search Documents

By Rashid Bashir

Shaft sinking through solid rock, which contains little or no water, poses little difficulty. However, when loose, water-bearing strata have to be contended with, water control measures, and pumping facilities are needed. Shaft sinking in Athabasca Basin requires sinking through water bearing sandstone which can be highly fractured. Intersection of local zones of extensive fracturing results in the potential for high water inflows with pressures up to 5 Mpa. Grouting is carried out ahead of each shaft sinking interval as water control strategy. In the grouting method, liquid cement is forced into the water-bearing earth under very high pressure. Shaft sinking performance which can be quantified in terms of rate of advance is highly dependent on the days spent at each interval grouting before sinking can advance to the next interval. This paper presents the shaft sinking experience in Athabasca basin and how some of this is translated into Geoscientific Investigations for Future Shafts. A comparison of Geoscientific data collected from future shafts at McArthur River and Millennium Mines is compared to historical data collected from pilot holes, where shafts have already been sunk. The paper concludes with the strategies for better integration of hydrogeological, geotechnical and geophysical data.

Aug 1, 2010

By Atul Bhatnagar, M. P. Sinha, Md Zahid Ahmad, Pallav Garg, Sanjay Kumar Singh, Shashi Ranjan, An Ecolab Company Nalco Water

"Froth Flotation is undoubtedly one of the most critical processes in coking coal washing plants. This work was carried out at Bhelatand Coal Preparation Plant of Tata Steel was with an objective of cost optimization in fine coal processing. The sources of raw coal for the plant include coal from underground mines of Jharia coalfield and procured open-cast raw coal. Coal from different sources vary in quality and possess different floatability characteristics.Synthetic collector is being used in plant as a flotation reagent. An alternate collector with new chemistry was developed for reducing total treatment cost without compromising product yield and quality. A series of laboratory tests were conducted to assess the performance of various sources of raw coal and plant scale trial was started. At first, the new generation coal collector was entirely substituted with the existing collector in the laboratory scale. However the plant scale trial data was not in accordance with laboratory results and indicated inferior flotation performanceThe issue was studied and data based conclusions were drawn that the new generation collector aids faster and uncontrollable kinetics. A decision was taken for co-dosing of the synthetic and new collector for the second phase of the trial. A detailed laboratory analysis was done again and few dosing ratios that predicted optimum results were selected for plant trial. The dosing ratio was optimised as per flotation yield and product ashes during the plant trial. The results showed significant improvement from the first phase and optimum dosing rates were decided based on plant observations and data collection. The influence of various process indicators including water quality, feed and product ashes and process yield was studied during all the trials and promising results were established. The co-dosing of both the collectors conferred cost advantage and enabled to achieve superior performance."

Jan 1, 2016

By Robert Cameron, Colin Ashton, John MacNeil, Leo Piciacchia

"The in pit dam construction and utilities relocation, known as the East Mine Corridor Relocation (EMCR) project, was developed to extend the life of the east side of the Base Mine pit by two veal's. This will result in the recovery of an additional 80 million barrels of oil and delay expenditures associated with the opening of the North Mine by two years. To accomplish this, a large in pit earth structure was required to provide a new embankment foundation for relocating a public highway, four powerlines, a natural gas back-up pipeline, a substation, and a conveyor train. This structure would also he required as a temporary dam 10 contain mature fine tails on the west side until mining is completed in the east mine corridor area, that will then be filled with fluid.The in pit dam, known as The Highway Berm, is 2.5 km long, 63 m high and has 42 million m3 of engineered soil added to the already existing end-dumped soil volumes. To complete the design and construction of a structure of this magnitude, in the very short time frame of two-and-a-half years, presented many new challenges. The main challenges faced were: designing while construction was ongoing; designing without the use of clay cores or sand filters; using relatively non-select overburden material; proper dewatering and base preparation; changing from construction of 50 m high spoil piles to a high specification construction operation; compacting lifts with heavy haulers; constructing during the winter; and monitoring movement of the structure with satellites."

Jan 1, 1995

By Ali Hashemi, Anna P. Perry

The PQ Deeps (PQD) is a production zone located at Newmont’s Musselwhite Mine in northern Ontario. Development started for the PQD in late 2017, and the first stopes were mined starting in early 2021. Unlike most historic longitudinal stoping of narrower orebodies at Musselwhite, the PQD is a wider orebody following the plunge of a fold hinge and is extracted primarily by transverse stoping. Some geotechnical challenges were experienced during early stoping efforts, necessitating design changes throughout late 2021 and early 2022 to optimize the stope design. This work describes the mining methods and design changes to transverse PQD stoping based on geotechnical lessons learned during early stoping efforts.

Jan 1, 2023

By J. Duby

"A description is given of a series of tests performed to determine the comparative effects which dynamic and static straining, in compression, have on the physical strength properties of mild steel and an aluminum alloy. The dynamic deformation was imposed during the passage of single stress pulses of about 100 micro-second duration. These pulses were recorded with strain gauges mounted near both ends of the specimen. The resulting records were analysed using a simple wave theory; there from the dynamic stress-strain curves for the respective metals were deter-mined and were then compared with the static stress-strain relation. The respective hardnesses of the metals after deformation are evaluates by means of static stress-strain curves in compression. The micro-structures of the metals before and after deformation are also shown. It is observed that dynamic de-formation considerably modifies the rate of strain hardening. This modified hardening appears to be persistent. The observed differences in physical strength properties and micro-structures are discussed in the light of the accepted dislocation theory for metals."

Jan 1, 1960

By J. R. Pacheco

Paranapanema group has decided to implement the business system SAP R/3 in all companies of the group in order to replace all current applications. This project has taken nine months to be completed. This paper describes the phases of this implementation, with focus on the Plant Maintenance component. In addition, it gives an idea of the effort required to implement SAP R/3 on an organization the size of Paranapanema group.

Jan 1, 2007

By M. Okada

Consumption of refined copper in Asia, especially in China and India, has soared, and the copper price is at its historic height. New smelters and refineries have been built in the region with state-of-the-art technology to meet the unprecedented demands. Supply of copper concentrate, on the other hand, has fallen short of the growing demand for concentrate by the smelters and refineries with expanded production capacities. The shortage of copper concentrate is attributable to the delay in the mining development, caused by the prolonged price slump of before 2005. The mismatch between supply of concentrate and smelting and refining capacities may cause disorderly movement of copper price, and hamper the sound development of the industry. The recent high copper price may prompt substitution with alternate materials. With electrical and thermal conductivity and workability, copper is one of the most customer-friendly materials. It is regrettable for both customers and suppliers if the high copper price would become an impediment to promoting copper use. Some outdated and environmentally unfriendly facilities still operate. In view of recent lower-grade copper concentrate with higher sulfur content, these facilities must reform their equipment to environmental-responsive one. The current level of per capita consumption of refined copper in Asia shows that the demand of copper will further grow. It is necessary to realize stable supply of refined copper and stable copper price, to help developing countries including China and India to economically take off. Hence, it is essential that the development of the copper industry be accompanied by environmentally friendly facilities, and harmoniously increased capacities between mining and smelting and refining.

Jan 1, 2007

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By Z. D. Hora

"There has been a number of new developments in British Columbia's industrial minerals field over the past few years. Several new industrial operations were started to diversify the line of British Columbia mineral production by magnesite, perlite and fuller's earth. Industry activities and geological projects have identified occurrences of rare earth minerals, niobium, kaoline, fireclay and zeolites. The Geological Survey Branch significantly improved its database on industrial minerals. New geological concepts based on recent work are opening a number of new opportunities f or further industrial minerals' exploration and development in British Columbia.IntroductionTraditionally, the value of industrial minerals produced in British Columbia in any given year comprises between 100/0and 15% of the combined value of minerals, coal, petroleum and natural gas. Over the years a wide variety of industrial minerals has been produced , often with different levels of marketings success. For some products, such as dimension stone and clay or shale products, initial strong demand gradually dissipated; for others such as asbestos and magnesite, new discoveries or new industrial activities created demand and new markets . In some cases, such as fluorite , talc, pyrophyllite and perlite, wider use has been prevented by small size, poor quality or remote location of the deposits. Also, British Columbia , with 2.6 million inhabitant s, provides only a limited market and the industry therefore has to look beyond provincial borders."

Jan 1, 1990

By E. Lehtila, J. J. Talja, R. Jahila

Kopar Oy is acknowledged for engineering and manufacturing of robust systems for bulk material handling, especially at power plants and non-ferrous smelters. We have over thirty years of experience with systems specifically designed for hot and abrasive conditions, aiming at low cost of ownership, low operational expenses and high availability. Although Kopar has numerous applications in mechanical conveying, there is an increasing number of pneumatic conveying applications at copper smelters. They relate to conveying of concentrate, and primary and secondary flue dusts. Challenges of pneumatic conveying for concentrate are mechanical and do relate to broad particle size distribution and high abrasivity of the concentrate and the silica. Therefore, special attention shall be paid to system design and ceramically lined bends in the pipeline. Challenges of pneumatic conveying of primary flue dust relate predominantly to material stickiness and poor flowability which are mainly due to fine particle size and formation of sulphates and furthermore, crystalline water. Additional challenges of secondary dust, the white converter dust, are primarily due to the extremely fine 0.1–1.5 µm particle size and problems which come with this. Effect of material characteristics like size distribution, morphology and chemical composition in pneumatic conveying are discussed in detail. INTRODUCTION Fine materials like concentrate, feed mix, flue dusts (from waste heat boiler and electrostatic precipitator) and secondary dusts need to be conveyed at smelters. Both horizontal and vertical conveying and combination of those are used. For the purpose, both mechanical and pneumatic conveying are applied. Most widely used equipment are drag chain conveyors and various combination of pneumatic systems, e.g. air lift, dense-phase and dilute phase pneumatic conveyors. Kopar has 30 years’ experience with multiple material handling systems. Furthermore, acquired companies like Elmomet Oy and SITE Oy (both currently fully merged and integrated into Kopar Oy) have even longer history, especially in pneumatic conveying. It is commonly known that the finer the dust the more difficult it is to be conveyed pneumatically. Sulfates with crystal water makes it all even more difficult, if not ineligible. Challenges related to pneumatic conveying of various fine materials is discussed in detail in the paper.

Jan 1, 2019

By G. M. Ritcey, K. E. Haque

"Laboratory-scale sulphuric acid leach tests were conducted on Elliot Lake and Rabbit Lake ores in the presence of various oxidants, namely: Fe2(SO4)3, CI2, H2O2, NaClO3, MnO2, H2SO5, HNO3, Oxon e, K2Cr2O7, KMnO4, O3 and O2. Uranium extraction is significantly accelerated when an oxidant is present in the leach slurry. Uranium extraction of 96-99% can be achieved by maintaining the oxidation potential of the leach slurry in the range of400 to 500 m V (S.H.E.). A rough cost comparison of all the oxidant s indicates that the use of Fe2(SO4)3, 02, O3, C12, HNO3 or MnO2 is far less expensive than NaClO3 and the uranium extraction rates are similar to or better than with NaCIO3. For uranium extraction, it is concluded that gaseous oxygen (i.e., air or oxygen) would be the most effective and economical oxidant for the 24- to 36-hour leach of Elliot Lake ore; whereas for the 8- to I2-hour leach of Rabbit Lake ore, a strong chemical oxidant (e.g. NaCIO3, H202, 03, K2Cr2O7, H2SO5 or HNO3) would be a logical choice.IntroductionThe common practice for the treatment of uranium o res is leaching with sulphuric acid or with a carbonate-bicarbonate mixture. Generally, the latter process is ad opted when an excess (> 18%) of acid-consuming components (e.g., carbonate) is present in the ore. Irrespective of the nature of the leachant, the addition of an oxidant to the leach mixture is necessary to obtain a high uranium extraction.The maximum extraction of uranium can only take place when all the uranium is in the highest oxidation state (i.e.,U +6-uranic ion) . Because a certain percentage of uranium present in the ore is invariably in the lower oxidation state (i.e.,U+4-uranous ion) , the addition of an oxidant to the leach slurry is necessary to oxidize uranous ion to the uranic state."

Jan 1, 1982

By P. Hickey, G. Hubert, P. Healy

"J. S. Redpath Limited, an underground contractor with a worldwide presence, has implemented innovative techniques in various projects in Canada to shorten the development cycle. Conventional methods currently used for installing primary ground support are compared with the Australian technique of bolting and meshing with jumbos equipped with twin telescopic booms, in-cycle shotcreting, and the use of two jumbos and two scissor bolters set up side by side in wide headings. Recommendations and lessons learned are presented with the aim of providing realistic expectations with regard to development advance rates in a mining environment.RÉSUMÉ J. S. Redpath Limitée, un entrepreneur minier souterrain d’envergure mondiale, a complété plusieurs projets au Canada où des techniques novatrices ont été mises en oeuvre pour raccourcir le cycle de développement. Cet article présente une comparaison entre les méthodes conventionnelles fréquemment utilisées pour le support de terrain, la technique australienne de boulonnage et d’installation de grillage au moyen de jumbos équipés de flèches télescopiques doubles, du béton projeté appliqué durant le cycle de développement et de l’utilisation de deux jumbos et deux boulonneuses côtes-à-côtes dans des galeries de grandes dimensions. Les recommandations et les leçons apprises sont présentées dans le but de fournir au lecteur des attentes réalistes quant aux taux d’avancement du développement dans un environnement minier."

Jan 1, 2016

By I. S. Thompson

A program of geochemical till prospecting, carried out by Derry, Michener & Booth in 1974, was instrumental in t~ e discovery of a copper deposit in Currie Township, Ontario, beneath thick lacustrine deposits of the Abitibi Clay Belt. The prospecting system involved the continuous collection of glacial sands and gravels beneath the clays, using a track-mounted, dual-tube rotary drill, and the separation and geochemical analysis of the heavy mineral content for Cu, Zn, Pb, Ag and Au. In one of 22 holes drilled down-ice from nine Canadian Nickel airborne EM conductors, fragments of chalcopyrite-bearing graphitic argillite, assaying 12% Cu, were recovered from a 14-foot gravel section beneath 83 feet of clay. Ultimately, mineralization was identified in 10 of 11 additional holes drilled up to 3,000 feet down-ice from the Currie deposit. The glacial fan, when compared to the 1,200- by 165-ft area of the subcropping mineralization, is at least 20 times the area of the deposit and is the result of glacio-fluvial reworking of the mineralized ground moraine. The Currie deposit is contained within a Keewatin succession of graphitic argillite, dacite tuff and graywacke, which is intruded by dacite and feldspar porphyry sills and dykes and truncated by a Keweenawan diabase dyke. Grade and thickness of the mineralization, which lies chiefly within the argillite, is related to felsic intrusives and hydrothermal alteration, and to fold hinges.

Jan 1, 1979

By Hamid Mahmoudabadi

In the present paper, the performance of four approaches based on neural networks and geostatistical method for grade estimation are compared and analyzed their performance to find a proper method. Four methods, Multi Layer Perceptron neural network (MLP), Radial Basis Function (RBF), General Regression Neural Network (GRNN) and Ordinary Kriging (OK) are selected for ore grade estimation of variable Fe in an iron deposit located in Iran. For each method, two diagnostic statistics are calculated: Mean square error (MSE) and correlation coefficient. The results show the superiority of the General Regression Neural Network.

Oct 1, 2009

By J. C. Moreno, G. Rios, M. Palacios

The Huelva smelter was commissioned in 1970 coinciding with the shutdown of the old smelter in the Rio Tinto mine site. That new smelter consisted of two Momoda blast furnaces with a capacity of 500 dmtpd of concentrate. Nevertheless, soon after their start-up, it was clear that an increase in the smelting capacity was needed. After an analysis of the existing alternatives at that time, the flash smelting technology was chosen. The new Outokumpu Flash Smelting Furnace (FSF) came into operation on 18 September1975, with an initial capacity of 900 dmtpd of concentrate, using four Venturi-type burners and preheated atmospheric air. Since that date the Huelva Smelter team, together with Outokumpu (now called Outotec), have continuously improved our FSF design, process conditions and operational practices, leading to a present capacity of 3,500 dmtpd of concentrate. Since 1975, five smelting campaigns have been completed, the last ending in November 2013 with the rebuilding of the original FSF hearth. This paper describes the history of these improvements and the lessons learned.

Jan 1, 2014

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By T. Skinner, M. Sahebkar

"In recent years, the mining industry has been inundated with new technologies and software systems to aid in productivity improvement. Accompanying this increased level of technology and computer systems has been the exponential growth in data sources and sinks for all aspects of a mining operation. This rapid growth in data and technology has evolved through vendor “push” approaches and user “pull” scenarios, the result of which has been that currently, no standards exist defining how data from new technology should be accessed and transferred from surface mining equipment and systems. Consequently, many incremental benefits of the systems have not been realized. This paper will present a discussion of this important issue and introduce a new committee formed to address standards to assist the industry in making effective use of current and future technology. Potential benefits accruing from the development of these standards will be illustrated through the use of a case study at Fording Coal Limited. IntroductionThe mining industry is currently faced with a rapid evolution in the computing-based systems capabilities of mobile production equipment. At the same time, there is a trend toward the introduction of even larger machines, with novel designs or incorporation of new technologies within existing designs. Computing and control technology will be required to operate and acquire knowledge about equipment operation, utilization, and performance. Such knowledge has the potential to lead to enhanced equipment design, more appropriate equipment selection, and optimized equipment performance. The equipment systems will be required to be integrated with mine production monitoring systems, maintenance management software, and a wealth of other information systems to provide a complete understanding of the effects of various factors such as maintenance, equipment design and production on economics (Roman and Daneshmend, 2001). This will lead to a better understanding and implementation of the opportunities to enhance the performance of the mine through interaction of the mine operations."

Jan 1, 2003

By David L. Anderson

"The government o f Canada has, since 1981, been under intense political pressure to modify its foreign direct investment (FOI) regulatory regime(1). To date the government's response has been limited to administrative and ""cosmetic"" changes: substantive issues have been largely ignored(2). However, as long as the economy continues to flounder , the Foreign Investment Review Agency (FIRA), as it is presently formulated , will continue to be an easy target for government critics . This phenomenon, in conjunction with the virtual certainty of a federal general election within two years, suggests that changes to the FIR Act will be seriously entertained by the present government.Recent events indicate that if change s are made, they will likely entail the adoption of a special-sector approach within the existing framework of a general screening system(3). Since this approach is currently employed in Australia(4), it would seem to be appropriate, from a public policy perspective to study that country's experience in developing and operating such a scheme. In doing so, I shall focus on the mineral sector; the rationale for doing so is as follows. First, this sector served as the focal point of the Australian FOI regulatory debater(5), Second , with the exception of the oil and gas industries, the non-petroleum mineral sector is one of the few areas of the Canadian economy wherein the Trudeau government has adopted an explicit domestic ownership target(6). Third, the non-petroleum mineral sector is, undoubtedly, a prime candidate to be denoted a s a special-sector if such a framework were to be utilized by the Canadian government!"".Although international comparisons are fraught with danger , a Canadian/Australian comparison is particularly appropriate(8). Both countries have reasonably similar economic, political and social structures . Furthermore, as noted above , Australia is the only other western country which employs a general screening mechanism for FOI. In addition, it utilizes a special area approach ; within this scheme, an explicit target of a minimum of 50% Australian ownership of all new resource projects has been formulated and clearly promulgated to all of the relevant interest groups. This policy, broadly defined, has been in place for more than six years and during this time the Australian mineral sector has, by world standards, prospered(9). Hence, the Australian experience in designating the mineral sector as a key area within a general screening system, should be of interest to Canadian policy-makers."

Jan 1, 1984

"The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members — the Universities of Queensland and Sydney and the CSIRO1, and by its industry members — BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining. Mechanized Rock ExcavationThe disadvantages of the drill-and-blast excavation method are widely recognized and the last half of the 20th century has seen mining companies and mining research organizations aggressively pursue technology to excavate rock by other means. As discussed below, despite considerable effort and large amounts of funding, the quest for mining’s “Holy Grail” has been unsuccessful in all but the weakest rock types.COMRO (the Chamber of Mines Research Organisation) supported by the South African gold mining industry, spent three decades and (probably) tens of millions of dollars developing prototype drag bits and, later, impact breaking machines aimed at the mechanized stoping of narrow, tabular reefs. This work has not yet produced a commercially-attractive mining system. Work continues in South Africa to mechanize these stoping operations although now the emphasis is on the use of diamond-wire sawing techniques. This work remains in the experimental phase.Both British Coal and Germany’s Bergbau- Forschung spent many years developing techniques trying to extend the range of rock types which roadheaders could cut economically. Again, although new knowledge was produced, it is difficult to claim that any new commercial mining systems emerged from this work."

Jan 1, 2001

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997