Search Documents

By Neal Harries

Ground movement is normal in open cut mining operations, mainly caused by excavation response and blasting. Movement of the ground can be acceptable provided it is not unexpected and catastrophic. However, in steep mine walls and the very large open pits being developed today the consequence of slope collapse can be catastrophic. Such risks can be minimized at the planning stage by reducing slope angles, but this carries a very high cost. Also, instabilities which develop whilst mining can lead to ore reserves being quarantined, which represent a high cost to the mining operation. In spite of such safety measures, unexpected failures have occurred in the past. These issues motivated the development and production of the slope stability radar (SSR). There are currently over 80 GroundProbe SSR systems deployed in metalliferous and coal mines in 17 countries. The unexpected failure of rock walls at mining sites is a major cause of death and serious injury. Slope failure is also one of the major causes of economic and production losses. An unexpected wall failure can bury critical equipment. It also disrupts the mine plan. It is common to cease mining for several days or weeks following a wall collapse due to uncertainty over stability. Direct economic losses in remediation alone can easily exceed $1,000,000 per incident. The economic costs of injury or fatality are much higher including closure of mines during the incident investigation process. Massive wall failure can result in direct and indirect costs measured in millions of dollars. This paper will present some recent case studies of the SSR operation in open cut mines in North America, including Thompson Creek Mining Company (Idaho), Smoky Canyon Mine (Idaho), and a general case study on extreme cold weather use of the SSR.

May 1, 2009

By Gurupraveen Ramanathan

Slot raises are relief holes within a stope in longhole stoping methods, designed to provide a free face that facilitates the expansion of the blasted rock during blasting, ultimately achieving the desired fragmentation. Various methods are employed to produce these slot raises, like conventional drop raise drilling, raisebore & V30 drilling. However, slot drilling is generally characterized by high costs and limitations in precision, resulting in unplanned ore losses and dilution. This paper introduces a novel alternative to slot drilling referred to as the "paste slot", designed specifically for paste backfill operations in underground mining. This new method emphasizes considerations in cured paste strength, paste wall removal, and stope dimensions and employs modified drop raises or dumped rings to optimize blast gas effectiveness and material flow. The paste slot method eliminates the need for reamers and reduces the total slot drill meters an average from 650m to only 300m for narrow stopes (3-4m wide). This significantly reduces the stope cycle time, leading to substantial cost savings and increased productivity. This new method was successfully implemented at the underground mines in Canada and Australia, resulting in a 20% reduction in stope cycle time and cost savings of 53,000 USD per slot compared to the conventional slot. This paper discusses the design and execution strategy of the paste slot method in underground paste backfill operations. It highlights the advantages of the method, shares operational insights gained during implementation, and showcases its potential applicability to other mines across Canada and globally.

Oct 1, 2024

By L. Louis

High resolution X-ray computed tomography imaging (with voxel size 48 µm) was conducted on various sandstone samples with different initial degrees of heterogeneity. All samples were imaged intact, and some after having developed localized compaction features in conventional triaxial experiments at high confining pressure, i.e. in the shear enhanced compaction domain (Wong et al., 1997). Our analysis of heterogeneity from X-ray CT data is based on the use of the coefficient of variation d =s /µ (s being the standard deviation and µ the average value). The coefficient of variation was shown by Otani et al. (2005) to be a convenient indicator of material heterogeneity in CT images of experimentally deformed sand piles. The authors reported differences in d before and after their experiments, and interpreted these differences as the effect of grain crushing resulting in more even material distribution within the voxels, hence in lower d values. The same concept was used by Louis et al. (2006) to image contrasts in d values throughout a volume of rock that had developed compaction bands in triaxial laboratory testing, knowing that the bands that had formed could be identified by visual inspection but not on the X-ray CT images. This study resulted in a radically enhanced image of the discrete compacted zones within the CT-scan series, whereby more deformed areas showed relatively low values of coefficient of variation due to grain crushing and pore collapse, as compared to nominally undeformed areas.

May 1, 2009

By Rick Steen, Weldon Read, Morrism Tracy T.

Edging for starter sheet blanks used in conventional copper refineries has always been problematic for getting the edging to seal and adhere to the titanium material used for the blank so that copper is prevented from plating under the edging and cause undo problems in getting the copper sheets to separate from the blanks. A method was developed at the Amarillo Copper Refinery utilizing an injection molding process that better adheres the edging material to the titanium that makes the harvesting of starter sheets much easier to the point that robots are now used to strip with and which holds up very well to the unforgiving physical nature of the electroplating process. It is believed that this technology could be successfully utilized for permanent cathodes as well. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery. The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By William A. Price

The objective of this paper is to outline the approaches used in British Columbia to address the challenges posed by metal leaching and acid rock drainage (ML/ARD). Challenges include the large financial costs, the need for site-specific assessments, the large information requirements, the need for mitigation measures to be designed and financed in a manner that permits long-term performance, the lack of long-term operating experience, the ongoing changes in many important processes, the need for pro-active detection and resolution of concerns, difficulties in predicting the potential for ARD or significant metal leaching, the need for new tools, and the multidisciplinary, highly specialized nature of the work. Consequently, mines must be planned, operated and closed in a manner that permits regular review, detailed monitoring and adaptive management. Proper consideration of the challenges involved, including a plan of how all outstanding concerns will be addressed, studies to address areas of significant uncertainty and caution in the absence of the required understanding, should ensure environmentally safe practices in the future.

Nov 1, 2002

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By A. J. Neale, B. C. Flintoff

"A review of the dynamic rod mill-ball mill grinding circuit simulator developed at the University of Alberta, highlighting the modular structure and open-ended design, demonstrates the ease with which classical feedback control strategies can be designed and implemented. Various open loop simulations are presented to demonstrate the highly interactive nature of the grinding circuit and to indicate where potential control problems may be encountered. Closed loop simulations are examined, beginning with the basic SISO classical feedback control of circuit product size. Further improvement in the grinding circuit performance in the presence of various disturbances is realized through the application of a classical MIMO feedback controller. As an example of advanced (multivariable) control, static decoupling is implemented and shown to provide additional improvement in overall circuit performance.INTRODUCTIONIt has long been recognized in the processing industries that a dynamic process simulator is an indispensable tool in the design and evaluation of automatic control schemes. In mineral processing the lack of these simulators is felt to have been a major hindrance to the widespread implementation of effective process control systems. In particular dynamic simulation is a necessary precursor to any study of modern (as opposed to classical) process control methods. This paper discusses the development of a dynamic simulator that can be used to study various feedback control strategies. The simulation software provides a powerful educational tool for those individuals interested in grinding circuit control."

Jan 1, 1988

By R. Mckinstry, M. Rantapaa, T. Bolles

"Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore.Barrick Goldstrike’s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs."

Jan 1, 2005

By M. Massinaei

Recently constructed circuits have included multiple stages of columns in a variety of applications, from roughing to cleaning. The Miduk copper concentrator (in south-eastern Iran) is one of the unique mineral processing plants which use column flotation cells as rougher. As the bulk of final concentrate is produced by rougher columns, optimized metallurgical performance of these cells is crucial. This paper will present the study and optimization of, a froth washing system of columns. For this purpose, the cross-sectional area of orifices was increased and their orientation altered. Concentrate assay for copper and silica, in addition to bias rate were found to be the assessment criteria. Modification of the wash water system resulted in increasing the purity of rougher and final concentrate. Negative bias and short-circuiting of wash water into the concentrate launder were the main causes of improper froth zone washing in the former system.

Jan 1, 2007

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By T. Takayama Filho

Votorantim Metais Zinco is a smelting facility which produces SHG zinc, zinc alloys, sulfuric acid, liquid SO2, copper sulfate, cadmium metal and silver concentrate. It is located at Juiz de Fora, Minas Gerais State, Brazil. This facility has been operating since 1980 and its current capacity is 95,000 tonnes of zinc per year, using mostly imported sulfide concentrates.The plant uses the conventional roast-leach electrowinning (RLE) process, in which iron is removed from the circuit as jarosite. The residues generated by the RLE process, which amount to about 200 t/day (dry weight), were until 10 years ago, deposited in tailing ponds having no impervious lining. More recently, jarosite and other wastes have been deposited in a properly built reservoir, but this is reaching its maximum capacity. In order to decommission these disposal operations and to reclaim the sites in an environmentally acceptable manner, Votorantim Metais concluded in 2004 a rehabilitation project for the old tailings pond and prepared detailed plans for managing the current and future disposal of jarosite-bearing residues. This paper describes the procedure for removing iron from the hydrometallurgical circuit and discusses the past and current status of the residue disposal sites, as well as the future challenges related to the environmentally acceptable handling of iron residues.

Jan 1, 2006

By Rene Klymowsky, Norbert Patzelt, Egbert Burchardt, Johann Knecht

"The challenge of ""ore bodies getting steadily harder and lower in grade"" was brought to light during the first oil crisis in the 70's. Shortly afterwards, HPGRs appeared on the scene with the promise of saving energy. This combined with developments in wear protection for the rolls ushered in a period of trade-off studies that considered the HPGR as an option to improve project economics or to even make projects feasible at all.Since then, applications of HPGRs at Cerro Verde (Freeport), PTFI Grasberg (Freeport), Mogalakwena (Anglo Platinum), Tarkwa (Goldfields), Boddington (Newmont), Penasquito (Goldcorp), and others have contributed to the creation of a formidable basket of operating experience. Collected through years of successful operation, this information has been used to validate design criteria, scale-up factors and establishing a clearer picture of what ""to do"" and what ""not to do"".This paper compares results from various mining operations using HPGRs in their processing plants. Some of the lessons learnt in different operating environments are reviewed in order to support proper implementation and operation of HPGR's. Some of the development programs that have been initiated to improve wear life of the tyres and to reduce overall operating costs are reviewed. It is timely to summarize today’s experience and analyse its implications for existing and new operations"

Jan 1, 2012

Ni and samaria-doped ceria (Ni-SDC) cermet are desirable materials for making a solid oxide fuel cell anode working at intermediate temperature (800°C or lower) due to its good ionic/electronic conductivity at the reduced operating temperature. An advantage of the use of a Ni-SDC anode is the enlargement of the effective reaction zone in the interfacial area between the anode and the electrolyte. As a result of the mixed ionic/electronic conductivity of the anode, the electrode reaction rate is enhanced. Investigations into the properties of the ceria-based anode reveal that the performance of the anode is closely related to its microstructures, which are dependent on the composition and fabrication conditions of the ceramics. In this paper, a method for quantitative characterization and correlation of Ni-SDC cermet microstructures to the performance of an anode is investigated. A series of Ni-SDC anode samples are prepared by screen-printing (SP) and spin-coating (SC) techniques, and different microstructures of the samples are obtained through controlling the SP or SC conditions and the sintering temperature. Individual phases (Ni, SDC and pore) in the tri-phase boundary (TPB) microstructures in the electrode are differentiated and segmented from each other in optical and SEM images based on the differences in refractivity and atomic contrasts among the phases. The geometric properties of the segmented phases are characterized using image analysis methods, so that a quantitative skeleton illustrating the TPB microstructures of the Ni-SDC electrode is obtained. Statistical analysis of the distribution of the three phases in the TPB microstructures is performed and the relationship of the microstructures with the optimum electrode is interpreted in terms of the microstructure analysis data.

Jan 1, 2005

"In mineral exploration and mining applications, it is sometimes necessary to reduce sampling error in order to improve representivity of individual sample assays. Historic efforts to reduce sampling error have relied on the belief that larger samples exhibit less sampling error. Justifications for this belief traditionally have coupled the binomial theorem with an ideal geological material consisting of ore and gangue particles of equal size and shape (an equant grain model) and empirical tests of geological materials, to illustrate an inverse relationship between sample size and sampling variance. To date, no proof exists of this sample size-sampling variance relationship in real geological materials exhibiting variations in grain size, shape, composition, and degree of liberation.Using first principles calculus and the formula for the mean, sample mass and sampling variance are proven to be inversely proportional in all geological materials. Distribution assumptions and physically ideal geological models are not used in this proof. Furthermore, algebraic manipulations of expressions describing the variances of equant grain models consistent with binomial, hypergeometric, and Poisson distributions reveal that these models also exhibit an inverse sample size-sampling variance relationship. Thus, the sampling behaviors of these models are numerically consistent with the sampling behaviors of real geological materials, and these models can be used to estimate sampling errors in real geological materials using simple sampling parameters."

Jan 1, 2007

By Patrik Ericsson

During the 90?s Atlas Copco and LKAB developed a pioneering fully automatic long hole production drilling system based on the Atlas Copco Simba W469 drill rigs. These drill rigs have since then drilled about 8.000.000 drill meters at the LKAB Kiruna and Malmberget mines. In 2005 LKAB ordered three new Atlas Copco Simba W6 C, to complement Simba W469s still in operation. These new Simbas are based on the latest generation computerized drilling technology have proven to meet the expectations of LKAB and now form a base for future automation in Kiruna and Malmberget mines. This paper will present experiences from the introduction of Simba W6 C in LKAB Kiruna and Malmberget mines. The paper will also elaborate on the latest developments in remote access and remote control technology making it a common automation option available for all computerized Atlas Copco drill rigs.

May 1, 2007

By D. Saramak, T. Gawenda, Z. Naziemiec, A. Saramak

"Crushing and grinding operations are burdensome to the environment due to generating large amounts of dust, noise and waste during course of comminution operations. An indirect negative contribution of industrial crushing processes is an increase of carbon dioxide emissions, which is a byproduct in energy production processes. On the other hand comminution processes in ore enrichment technology are essential due to liberation the useful minerals from the gangue, and producing the demanded particle size fractions of products. The article concerns investigation over negative influence of comminution devices on environment in terms of dust and noise emissions. Several various crushing devices were under investigations, both in laboratory and in industrial scale.The obtained results were analyzed in terms throughput and energy consumption achieved in various crushing devices. The test results allow to conclude that an intensity of dust generation for individual types of crushing devices is varied. An additional aim of this article is to link the aspect of mineral processing with its environmental impact and hence an influence of raw materials beneficiation industry on the quality of life of residents in immediate and close vicinity.INTRODUCTIONMineral raw materials beneficiation processes are an integral part of multi-stage processing of coal, iron ore and non-ferrous metals, production of aggregates, cement, or precious metals and stones. One of the common features of all beneficiation operations is their high energy consumption, which is mainly connected with various operations of feed particle size reduction. Comminution processes in ore enrichment technology are essential to expose and liberate the useful minerals from the gangue, while in aggregate production processes – to obtain the demanded particle size fractions of products. Crushing operations are characterized by a high degree of negative impact to the environment and humans, mainly due to:• High electricity consumption, which indirectly contributes to the increased emissions of carbon dioxide into the atmosphere, since CO2 is often one of the byproducts of energy production;• Relatively rapid wear of device working parts, what forces a production of spare parts and involvement of steel industry;• Intense dust pollution generated during crushing and grinding processes. This is one of the factors affecting the air quality and the consequent deterioration of the living conditions of inhabitants near mines and processing plants; and • Excessive noise emissions."

Jan 1, 2016

By B. R. Neufeld, M. G. Heximer, S. J. Roach, W. G. Van Luven, D. G. Reynolds

"Teck Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. In the zinc plant, zinc concentrates are roasted to produce calcine, which is then processed in the leaching circuit for zinc recovery. Calcine is first dissolved at pH <2.0. This is followed by a precipitation stage using additional calcine that removes iron as a ferric hydroxide precipitate which is recycled to the lead operations. It is during this pH adjustment that impurities, notably arsenic, antimony and germanium, are co-precipitated with ferric hydroxide which is the primary removal phase for these elements. Recent processing conditions have resulted in lower iron inputs to the leaching circuit and this has resulted in insufficient co-precipitation of key impurities. This paper summarizes the influence of iron concentrations on impurity removal using laboratory and plant scale surveys, and emphasizes key specification limits for the primary iron removal circuit.INTRODUCTIONThe Sulphide Leach Plant (SLP) at Teck Metals Ltd., Trail Operations produces a zinc sulphate electrolyte from three different zinc bearing streams:1. Calcine, primarily containing zinc oxide, from the roasters2. Zinc electrolyte from the Oxide Leach Plant (OLP) is produced by leaching zinc oxide fume from the pyrometallurgical lead smelting operations3. Zinc slurry from the Zinc Pressure Leach (ZPL) autoclaveThe feed sources are blended and introduced to the iron removal process to precipitate iron in the form of a hydrolyzed iron precipitate which is recycled to the lead smelting operation. Along with iron, impurities, namely arsenic, antimony, germanium and silica, also co-precipitate; this process acts as the primary removal step for these elements. Following iron removal, the electrolyte is further processed in the zinc dust purification circuits. Cadmium and copper are removed in the cold stage circuit via zinc dust cementation, followed by cobalt cementation in the hot stage circuit."

Jan 1, 2016

By Steve W. Ciccone

The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day icefree shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction. Steve Ciccone, AMEC?s project manager on the Mill Optimization project, works for the Mining & Metals unit of AMEC, a world leader in the provision of engineering and construction services. He obtained his BASc from the University of British Columbia and is currently midway through his MBA program at Simon Fraser University. Steve has 15 years of experience providing engineering and project management services on mining and metals projects, and has been involved in the execution of five capital projects and several studies at Red Dog since 1995. George Hope was responsible for process design and engineering on the Mill Optimization project and has been Manager, Project Development at Teck Cominco since 1995. Prior to this time, he was a project manager and chief metallurgist for Lac Minerals for 14 years and a mill superintendent and metallurgist for Noranda for 5 years. George received his BSc in Mineral Technology from the Royal School of Mines in England.

May 1, 2002

By Yi-xin Zhoa

The characteristics of coal bumps are analyzed based on the microseismic data from No.8935 workface in Xinzhouyao coal mine, Datong Mining Group. The geology of this workface is characterized by the thick sandstone roof and coal seam, both with relative higher stiffness and strength. In order to investigate the mechanism and precursors of coal bumps occurred in No.8935 workface, the locations of microseismic, the relationship of microseismic energy and frequency and the spectrum of microseismic signals are analyzed. The result shows that the coal bumps in No.8935 workface were mainly induced by the seismic caused by roof failure. The coal pillar near the goaf is more easily to bump. The statistics results indicate that the coal bumps were mainly occurred in the gate road near the pillar, less than 50m ahead of mining face and located in the hard roof adjacent with coal seam. Moreover, the frequency, energy, b-value and frequency spectrogram of microseismic events were found to decrease before coal bumps. It was found that the frequencies of the microseismic events before coal bumps mainly concentrate upon 5~60Hz. The sudden decreasing of frequency and increasing of amplitude of microseismic events can be regarded as a precursor of coal bumps.

Aug 1, 2013