Search Documents

By Gilles Carrière

"The Huntingdon mine of Quebec Copper Corporation is situated 3 miles south of the village of Eastman, in the Eastern Townships of Quebec. The copper deposit consists of several pyrrhotite-chalcopyrite replacement bodies or bands.The first mining operations on the conspicuous surface gossan of the Huntingdon deposit started in 1865. They were suspended in 1883. The .mine was again active from 1890 to 1893 and from 1912 to 1924. These operations were carried to a depth of 500 feet, and it is estimated that some 150,000 tons of ore were extracted, of a grade reported as varying between 3 Yi and 7 per cent copper.In 1950 a program of exploration was initiated in the area of the old mine, and resulted in the finding of 500,000 tons of ore with a grade of 2 per cent copper. A new shaft was sunk to a depth of 1,160 feet, and by February 1954 the mine was extracting 800 tons of ore daily.General Geology and StructureThe mineralized zones are on the west side of a band of altered volcanic rock, locally called andesite, adjacent to a sill-like body of serpentinized peridotite which lies west of the andesite. The bands of andesite and serpentine extend several miles north and south of the mine. Their strike is generally north 15 degrees east, and they dip steeply east. Their widths vary very considerably along the strike, but in the mine area each is about 450 feet wide on surface. They are enclosed in sediments of the Caldwell series, consisting of greywackes, quartzites, slates, and shales. The andesite belongs to the same series, which is thought to be of Cambrian age (1). The ultrabasic intrusive is post-Ordovician.At p\aces along the serpentine contact the andesite shows a pronounced schistosity; it is parallel to the contact and rarely extends farther than a hundred feet from it. No evidence of strong folding or faulting has been found so far in the mine workings. Some apparent distortions and irregularities in the strike of the contact may all be due to the intrusive nature of the serpentine. In the mine area, transgressive tongues of serpentine point southward in the andesite.A few vertical lamprophyre dykes, not more than five feet thick, cut the other formations at right angles."

Jan 1, 1949

By William W. Shilts

"In carrying out a geotechnical survey of a proposed gas pipeline route from the Arctic Islands south to Longlac, Ontario, the Polar Gas Consortium contracted the drilling of several hundred 2- to 2D-m-deep boreholes in drift and bedrock. Samples from these holes were made available to the Geological Survey of Canada, where they were subjected to stratigraphic and trace-element geochemical analyses. The geochemical characteristics of the clay and sand-sized heavy mineral fractions of till samples from these boreholes have been summarized in a series of geochemical profiles.From the proposed pipeline terminus at Longlac northward to the vicinity of God's River in Manitoba, tills contain significant amounts of Paleozoic carbonate rocks and Proterozoic sedimentary rocks derived from the Hudson Bay basin and lowlands. Within this section, two sites were enriched in base metals, indicating the possibility of local mineralization of possible economic interest.From God's River northward to Seal River, Manitoba, no evidence of local mineralization was noted. The heavy mineral fractions of the tills are universally enriched in Mn-rich siderite thought to originate on or in the Paleozoic section of the Hudson Bay lowlands.From Seal River northward to Thelon River, near Baker Lake, tills contain only components originating west of the Hudson Bay sedimentary basin. Near the Keewatin-Manitoba border, all till is enriched in uranium, which probably originates in the ""young"" porphyritic granites underlying much of the region, and produces a distinctive airborne radiometric anomaly.At the Thelon River, multiple till sections are variously enriched in Cr, Ni, U, Cu and Mo in the vicinity of a distinctive aeromagnetic anomaly.From Thelon River northward, several coincident zones of chromium and uranium enrichment are found where the line of boreholes crosses east-west-striking belts of volcanic, ultramafic and sedimentary rocks of the Prince Albert Group.The results of this study indicate that till tends to have characteristic element associations or concentrations over each of several broad regions along the pipeline route. These are related both to large-scale bedrock associations and to largescale effects of glacial dispersal. In addition, the samples, collected more or less at random with respect to local bedrock geology, have intersected several small-scale geochemical anomalies that appear to be related to zones of mineralization of possible economic interest."

Jan 1, 1980

"At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA) Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM.Preamble: At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA)-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM Reserve Definition and the CIM Estimation Best Practices Committees (the Committees). This information is intended to provide the Qualified Person (QP) with further guidance when estimating Mineral Resources and Mineral Reserves and in preparing a technical report written under National Instrument 43-101 (NI 43-101). Several members of the CIM Reserve Definition Committee, the CIM Estimation Best Practices Committee and some members of the Committee for Mineral Resources International Reporting Standards have reviewed these issues and provide the following commentary.Issue 1. - CSA requested CIM review and comment on the selection of an appropriate commodity price to be used in Mineral Resources and Mineral Reserves estimates.Commodity prices are used in the estimation of Mineral Resources and Mineral Reserves and in the economic analysis of a property. In times of rapidly changing commodity prices, or when prices are at the extreme ends of a commodity price cycle, the QP has a difficult job in selecting an appropriate commodity price.• The selection of appropriate technical variables, including commodity price, is clearly the responsibility of the Qualified Person (QP). The QP must describe the reasons for selecting these variables, including price, in the technical report.• The definition of a ""Mineral Resource"" contains the wording ""reasonable prospects for economic extraction,"" therefore, a QP must select economic parameters, including commodity price, that will result in an estimate of Mineral Resources and Mineral Reserves that have ""reasonable prospects for economic extraction""."

Jan 1, 2003

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"In January 1974, the Minerals Division of Canadian Occidental Petroleum Ltd. made the strategic decision to add uranium to its active exploration commodities and through compilation studies selected northern Saskatchewan as the most attractive and cost-effective exploration area in Canada. In August 1974, 100 sq. miles were staked adjacent to Gulf Minerals' Rabbit Lake deposit and east of the Esso Minerals Midwest boulder train. Initial exploration was based on geologic models of the Rabbit Lake deposit.In the summer of 1975, surface surveys delineated radon anomalies which were drilled that winter and found to overlie anomalous concentrations of uranium in the regolith which forms the upper unit of the crystalline basement. Within the crystalline basement, one hole intersected graphite and pyrite with anomalous nickel-cobalt-arsenic. Geochemical and radiometric surveys followed in the summer of 1976. Drilling in the winter of 1977 intersected several zones of graphite and also anomalous, but uneconomic, uranium abundances. Also in 1977, Dahlkamp and Tan (1977) described the coincidence of graphite and uranium at Key Lake and ground EM surveys on CanadianOxy claims detected graphite conductors beneath 250 ft of Athabasca sandstone. Inco Limited joined the project in April 1977 as a 50% partner. The project area was then surveyed using the airborne INPUT EM method, which detected 84 miles of conductors, with associated graphitic metasediments. On the ground these were located with MaxMin surveys, and follow-up drilling located the ""Tent"" Lake uranium zone.In 1978, the Midwest and Dawn Lake discoveries were announced, 7 miles and 2 miles west of the Joint Venture (J.V.) claims; and, in part for this reason, the 1979 winter drilling was concentrated on the deeper west side of the property. Exploration hole 102-79 intersected altered and uraniferous rocks, but stepout holes were barren. Drill hole 153-79 tested an under-snow three-station radon anomaly east of hole 102-79 and intersected 33 feet of 7.51 % U3O8, confirming the disco very of the McClean North zone. The geophysical grid of the McClean North conductor system was extended and detailed a strong, continous conductor to the south, called McClean South. This was drilled in January 1980and hole 1004-80intersected 22 feet of 2.95% U3O8."

Jan 1, 1983

By J. L. Dion

"A study of the techniques to integrally cast copper tubes in copper tuyeres for use in blast furnaces has been carried out. The work has been performed in support of current efforts to produce two-compartment tuyeres having improved water-cooling capacity. A test pattern corresponding to a vertical section of a two-compartment tuyere, and including a cast-in-place copper tube, was used to investigate such variables as tube preparation, tube coolant, pouring temperature, pouring rate and gating design. Successful castings, either with a good metalfurgical bond or good intimate contact between the tube and the casting, were produced, with all combinations of gating system and position of the tube tried. However, the pouring temperature, the pouring rate and the effectiveness of the coolant are interrelated and must be controlled to produce a good metallurgical bond.IntroductionAs part of its contribution to, and in collaboration with, the Copper Casting for the Steel Industry Committee, CANMET has undertaken research into the methods and techniques needed for the integral casting of copper tubes into high-conductivity copper castings.The objective was to produce two-compartment copper blast furnace tuyeres in which the water-cooled nose compartment consists of a copper tube metallurgically bonded to the wall of the high-conductivity copper casting. This design, developed in the UK, has demonstrated a much extended service life with attendant economies; unscheduled shutdown of blast furnaces due to tuyere failure is a significant problem in the steel industry. The Canadian steel industry believes that this design will replace the currently used single-compartment tuyere in blast furnaces within a few years.The technology to produce these tuyeres does not exist in Canada. One of the main features is the inclusion of a smooth-walled cooling channel in the nose, which permits high velocity cooling water to be employed. A second compartment acts as a reservoir backup, should failure in the nose occur. This would allow continued use of the tuyere for a period of time, permitting a scheduled shutdown for repair s. To assist the Canadian producers of tuyeres to maintain their market, and the Canadian steel industry to have a reliable domestic supply, it is important that the necessary technology for the production of two-compartment tuyeres be developed and transferred to industry."

Jan 1, 1982

By M. Nagamori, A. J. Plumpton

"A low-grade concentrate from the Crevier Township, Quebec, containing 1.8% Ta205 and 13.7% Nb205 was reduced with carbon at 1600°C, and niobium and tantalum were selectively absorbed in liquid iron. To slag off the zirconia-rich gangue, some silica and lime were added as flux. Metallic iron was added in such a way that the combined contents of TaC and NbC did not exceed 20% in the ferroalloy . Up to 95% of the niobium, and up to 80% of the tantalum contained in the concentrate were recovered in the metal. The ferroalloy was ground finely and dissolved in 2 wt % sulphuric acid to leach out iron and silicon preferentially. The insoluble residue consisted principally of NbC and TaC, the calcination of which yielded an enriched concentrate comprising 80% Nb2O5 and 8% Ta2O5. The insoluble residue could also be chlorinated to obtain an impure liquid of Nb2Cl5 and TaCl5. Process variables and their effects are discussed in terms of higher metal recoveries in the smelting.IntroductionPresently, about one-third of the world production of tantalum comes from the pyrometallurgical reprocessing of tin slag, a by-product of tin smelting, containing sometimes 2 to 10% Ta205 and about the same amount of Nb205. Upon heating tin slags with carbon at about 1600°C in an electric furnace, tantalum and niobium oxides are converted to TaC and NbC, which are absorbed by the coexisting phase of molten metallic iron(1,2). The Fe-Nb-Ta-C melts cannot be decarburized by oxidation because of the preferential formation of Nb and Ta oxides over CO gas(3). So, the ferroalloys containing tantalum and niobium carbides are commercially treated by acid-leaching and I or chlorination to eliminate iron and thus permitting the eventual recovery of purified tantalum and niobium oxides(2).Absorbing Ta and Nb carbides in molten iron was first proposed and demonstrated by Zimmerley and Back(4) in 1957 in order to recover selectively tantalum and niobium from lowgrade concentrates. The process was successfully applied to the electric furnace smelting of tin slags by Hunter and Fursmant(5) over a period preceding 1965."

Jan 1, 1985

By J. B. Heslop, D. S. Bubar

"The Gondor Zn-Ag-Pb-Cu deposit is a stratabound massive sulphide lens occurring within Archean volcaniclastic rocks of the Yellowknife Supergroup. The deposit is located in the west-central portion of the Slave Structural Province, approximately 350 km north of Yellowknife.Initial diamond drilling at Gondor has outlined a steeply dipping, L-shaped, folded, massive sulphide body, which may be traced over a strike length of approximately 800 m, and to a depth of 350 m. True widths of up to 40 m have been intersected in the thickest part of the deposit. Preliminary estimates suggest that the deposit contains a minimum of 7.5 million tonnes grading 6% Zn, 50 g/tonne Ag and less than I% combined Cu and Pb. In addition, significant gold, grading up to 2.8 g/tonne, occurs in some parts of the deposit. The mineralization is open both down-dip and along strike.The Gondor deposit lies conformably within a predominantly east-west striking, north-facing sequence of felsic to intermediate volcaniclastic rocks. Coarse fragmental rocks are abundant in the hanging wall, whereas ash and lapilli-tuffs predominate in the footwall. The main structural feature in the area is a large-scale, steeply northeast-plunging, Z-shaped fold. The sulphide mineralization lies within the synformal portion of this fold, with the thickest part of the deposit coinciding with its hinge zone. Several episodes of faulting have also affected the local stratigraphy.The wallrocks of the Gondor deposit were hydrothermally altered prior to the onset of medium-grade regional metamorphism. A halo of altered rocks surrounds the massive sulphide lens, with no apparent difference in the degree of alteration between the hanging wall and footwall strata. The alteration zone is characterized by the addition of MgO and K20 and by the depletion of Na20 and CaO. These changes are reflected in the mineralogy of the altered wallrocks by local enrichment in chlorite, biotite, muscovite and cordierite.The mineralized zone is medium- to coarse-grained, well-banded and is composed largely of pyrite, quartz, and sphalerite with subordinate galena and chalcopyrite. Preliminary studies of metal distribution indicate that a lateral zonation is present, with lead enrichment in the central part of the deposit, and copper enrichment toward both ends. Stringer-type copper mineralization has not yet been discovered in the footwall of the Gondor deposit."

Jan 1, 1985

By Walter Curlook

"With Inco recording record profits over the past year, most people have forgotten the painful years of the last recession/depression when Inco was losing up to a million dollars a day for a short period . While high nickel prices have contributed to the exceptional recent profits, the real achievements stem from the tremendous advances in productivity and cost improvements that make Inco one of the lowest cost nickel producers.Some of the major advances in productivity have occurred in the mines. The establishment of Mining Research Departments in both Thompson and Copper Cliff in 1979/80 provided the stimulus and the opportunity to dedicate personnel to specific research projects, on a full-time basis; and more particularly to concentrate on the efficiency of the total mine system. The Copper Cliff North Mine was brought back into production as a research mine dedicated to the development and testing of new mining methods and equipment. A shop facility known as the ""Murray Shop"" was set up as the centre of innovation for the development and construction of prototype equipment required for new bulk mining methods. While other expenditures were being curtailed , investment in mining research was being increased. An early success was an ""in the hole"" drill that could be broken down into small components to access even the remotest sectors of a mine to convert labour intensive undercut-and-fill mining to "" vertical crater retreat "" , VCR, bulk mining. A new mine manufacturing company-Continuous Mining Systems-was incorporated with the objective of building innovative mining equipment, with strong focus on automated continuous sytems. Continuous Mining Systems has now grown to a $25 million per year business. With these synergistic thrusts, the VCR bulk mining method was implemented in all of the Ontario Division mines, raising the percentage of ore mined by bulk mining techniques from 320/0 in 1981 to over 90% today. Coupled with re-designed job responsibilities, sup- ported by appropriate training, mine productivity more than doubled. It was discovered that VCR mining could be adapted to the narrower Thompson mine ores with identical improvements in productivity. Development of the Thompson Open Pit North had an additional favourable impact on production cost s in Thompson. The timing of the open pit development could not have been better. It permitted Inco to rapidly increase production at high productivity and low cost, in years of record demand and prices."

Jan 1, 1990

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By R. D. Brown

"AbstractIn order to raise the enormous amounts of capital which will be essential for the development of Canada's mineral and petroleum resources, this country's resource industry must be permitted to earn an acceptable rate of return. The existing tax regime, with its high rates, complexities and misdirected incentives, presents a serious obstacle to our resource industries in their development of Canada's immense , but increasingly lean, resources. Government tax and other policies are not the only cause of the crisis now facing the resource sector in Canada, but a reformed tax system, with stable and reasonable tax burdens, is required if Canada's resources of minerals, oil and natural gas are to continue to contribute in the future, as in the past, to our national well-being.An independent task force, organized under the auspices of the Canada West Foundation, has recently completed a wide -ranging report: on the future development of Canada's mineral, oil and gas resources. This five-volume report, completed after almost two years of research and study, concludes that Canada •is facing a major crisis •in the development of our resources, It states that unless corrective action is taken now, mineral production and exports could decline drastically after 1985, at the same time that Canada would face massive bills for imported oil because of inadequate and declining production.The task force, chaired by the author of this article, has put forward recommendations for a fundamental shift in both federal and provincial policies in order that Canada's mineral reserves can be developed in the national interest. This article consists of excerpts from the summary of the task force's report."

Jan 1, 1977

By Pingyang Zhang, Caichu Xia, Shuwei Zhou, Yu Zhou, Yongsheng Hu

A lined rock cavern (LRC) is an alternative container for compressed air energy storage (CAES) to store high-pressure air that is later used to produce electricity. A critical requirement of CAES in LRCs is that the inner seal should provide adequate sealing capacity to prevent air leakage from LRCs. In many studies, rubber sheets are applied to build the inner seal. However, air leakage through rubber seals has not been given much attention and rubber seals are usually assumed to be absolutely airtight. Given that rubber is permeable especially under high air pressure, such as in CAES, air therefore leaks through rubber seals during CAES operations. In this study, a numerical analysis was conducted based on the permeation equation of polymers and the governing equations of thermodynamics of CAES caverns to analyze the characteristics of air leakage from CAES caverns through rubber seals. A planned CAES plant in China was considered as a case study. Results show that air leakage rate increases with increasing cavern temperature and pressure during air injection and decreases as cavern temperature and pressure decline during air withdrawal. However, in total, the daily air leakage percentage is in the order of magnitude of 10-3% in a typical operation cycle, which is much smaller than the critical value of 1%. Under a common range of realistic operations conditions, the daily air leakage percentage is still of the order of 10-3%. Therefore, rubber seals can be used to prevent air leakage in LRCs for CAES. However, the experience of Japanese pilot cavern indicates that the specifications for the on-site vulcanization jointing and installation methods of rubber seals still need improvement.

Jan 1, 2015

By Norman A. M Macleod

FOR the past seven years, all flotation at the Britannia mill has been done in Forrester Air-Lift cells. Prior to 1931, the roughing and part of the cleaning operation had been performed in four 21-cell and two 14-cell M.S. machines. The resulting economies in reagent, power, maintenance, and general operating costs, and the increased recovery, more than justified the exclusive use of the Forrester machine. About three years ago, the possibility of still further improving the efficiency of the flotation section was the subject of considerable discussion and experiment. Arising from these experiments, tests were made of the practicability of using a cell of greater depth than that of any pneumatic or mechanically-agitated machine in common use. Cells were constructed with depths of 7 .5 feet, 10 feet, and 15 feet, and, in all cases, a very definite improvement in operation was indicated. The cell now being used in the mill treats from 5,500 to 6,200 tons of dry feed per day. It is 100 ft. long by 5 ft. wide by 8 ft. deep, and has replaced a total length of over 500 feet of standard Forrester machine. The choice of a depth of 8 feet was governed by the type of blower which was available-in this case, a Roots-Connersville blower, driven by a synchronous motor and delivering 6,000 c.f.m. of free air at 4.0 pounds per square inch. At the Chelan Division of the Howe Sound Company, where a new mill was recently built, all flotation is carried on in cells 10 feet deep, with good results.

Jan 1, 1938

By Veerendra Singh, Y. Rama Murthy, Sunil Kumar Tripathy, Nikkam Suresh

"High intensity dry magnetic separation is commonly employed to separate different para-magnetic minerals including mineral sand. Separation in these separators is majorly influenced by the combined effect of gravity, centrifugal and magnetic forces on a particle. These separators are included in the process flow-sheets either for pre-concentration purposes or for the beneficiation of paramagnetic minerals. Separation in these separators is majorly influenced by the difference in the magnetic susceptibility of the associated minerals, particle size and shape along with the process variables of the machine. Particle size is one of the major parameter that plays an important role and decides its probability of selectivity under the magnetic field. However, effect of particle size on the performance of these separators are not well understood which is evident from the literature.In the present investigation, an effort is made to bring out the effect of particle size on particle separation in an induced roll magnetic separator while treating ilmenite fines. Effects of operating parameters, such as; magnetic field intensity, roll speed, feed rate and splitter position have been studied and their influence on particle size has been analysed in terms of yield (wt.%) to magnetic product, particle size distribution characteristics in terms of D50 and D80 size, skewness, kurtosis. Also, the particle size distribution of each test was fitted in Rosin-Rammler equation. The test results were analysed statistically to understand and quantify the influence of each variable on particle separation. It is found that, rotor speed of the separator had maximum influence on yield to the magnetic product whereas splitter position had major influence on D50 and D80 (µm) size of the product."

Jan 1, 2016

By Phil Keele

"Manalta Coal Ltd. 's Vesta Mine will supply Alberta Power Limited's 740 MW Battle River Generating Station with 1 128 000 tonnes of sub-bituminous ""C"" coal in 1983. Mana/ta Coal Ltd. and Alberta Power Limited are in their seventh year of a 31-year coal supply agreement. With the exception of localized topographic highs where three coal seams are mined, the Vesta Mine is primarily a single-seam mining operation. Vesta's comprehensive programs of mine planning, preventative maintenance, reclamation, and employee relations make it an efficient and a well run operation. Introduction The Vesta Mine, located in east-central Alberta approximately 300 km northeast of Calgary, supplies sub-bituminous ""C"" coal to Alberta Power Limited's 740 MW Battle River Generating Station. The coal reserves and principal stripping equipment are owned by Alberta Power Limited. Manalta Coal Ltd. owns and operates the additional mining equipment and support facilities. Coal production is from a single pit, 3.5 km in length. Both single and multi-seam operations are encountered in the active pit. In 1983, production is anticipated to increase to I 128 000 tonnes from 906 000 tonnes in 1982. The additional tonnage will be achieved by operating 24 hours per day, 5 days per week. The following sections briefly highlight historical, geological and mining/reclamation aspects of the Vesta Mine. Figure I illustrates the location of the Vesta Mine in relation to the cities of Calgary and Edmonton. History Coal mining for domestic use began near the turn of the century in the Vesta Mine area. Initially, small underground room-and-pillar operations were dominant. As equipment technology advanced, surface strip mining replaced the underground methods."

Jan 1, 1985

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951

By Jim Wickens, Andy Cole, John Pekrul

"The roaster facility at Barrick Goldstrike Mine treats double-refractory sulfidic/carbonaceous gold ore. Prior to oxidation in the roasters, the ore is ground in two parallel dry grinding circuits utilizing 19’ Ø x 75’ double rotator mills. The design plant throughput was 12,000 dstpd. However, process improvements have significantly increased throughput rates by 25-50%. The current daily throughput record is 20,078 dstpd. Grinding circuit improvements contributing to this success include feed size reduction, ball size optimization, automatic ball charging optimization, and operating strategy changes. In addition to the changes already made, this paper discusses future optimization initiatives including on-stream particle size analysis and “real-time” ore hardness determination techniques.INTRODUCTIONBarrick Goldstrike Mines is located 29 miles Northeast of Carlin, Nevada, USA. Through 2001, the property has produced over 23 million ounces of gold making it one of the premier gold operations in the world.Prior to Barrick’s ownership, the property began producing gold from a small heap leach operation in 1975. The small-scale heap leach production continued through 1986, and in January 1987, Barrick acquired the property. Increased exploration activity by Barrick significantly increased gold reserves. In August 1988, a 4,500 dstpd mill facility was commissioned to treat high grade oxide ore. Also, heap leach operations had significantly expanded. In 1990, the mill was expanded to 6,000 dstpd, and the first autoclave was commissioned to treat refractory sulfide ore. By the end of 1996, the mill and pressure oxidation facility had expanded to 16,000 dstpd and heap leaching had ceased as oxide reserves were exhausted. In 2000, a roaster facility was commissioned to treat double-refractory sulfidic/carbonaceous ore."

Jan 1, 2003

By V. Silins, J. Tameling, R. C. Cook

"A general review of the wear problems encountered in the mining industry is presented and current practice for wear protection systems is reviewed.A new concept in wear protection is described and compared to alternative systems. Utilization of conventional stud welding technology and abrasion-resistant wear studs is shown to be a useful supplement or substitution for conventional techniques. Operating life of many consumable components can be increased by up to four fold. The technique is highly portable for on-site field application or can be used in shop environments.Details of the wear protection model and metallurgical properties of the wear component are also reviewed. Laboratory wear test data are reported to supplement field test performance or to screen potential alloy compositions for application in specific environments.A Review of Wear Problems and Wear ProtectionThe emphasis on wear protection has increased in recent years because of the increasing impact of the potential savings in time, materials and energy. A 1974 German study concluded that attention to tribology, the study of friction and wear, could save approximately $3 billion, and a study in the U.S.A. at the same time put the figure at $100 billion of which $20 billion was for materials. A more recent American study put the energy component of the potential savings at $16.2 billion per year. A recent British study estimated the total potential savings in the U.K. as $1 billion per year, with the largest savings coming from lower maintenance and replacement costs ($500 million), lower breakdown costs ($250 million) and increased machinery life ($200 million). These three major contributions are all potentially accessible in the mining industry."

Jan 1, 1982

By D. François-Bongareon

"In previous publications by the author, significant advances and generalizations of the theory of sampling of broken ores, prompted and confirmed by experimental results, have been presented. This paper shows how to implement these theoretical results in practice. The models to be used are reviewed, with a description of the various sampling parameters involved. Then the methodology for the experimental assessment of those parameters, including segregation factors, is described in simple and practical terms, along with the use of handy sampling protocol charts. Finally, the particularly important case of processing data from a sample-tree experiment is detailed, and examples of applications covering all situations and types of experiments are provided.IntroductionThe reliability of a sample of crushed material , i.e. the expected (average) deviation between its true grade and the true grade of the lot it comes from, mostly depends upon six factors:• the size (mass) of the sample (and to a minor extent, for small lots, the size of the lot);• the size of the rock particles (degree of comminution)• the nature of the mineralization at microscopic scale (i.e., within even the smallest particles);• the geological nature of the mineralization and mineral of interest;• the grade of the lot in the mineral of interest; and• in some cases, the state of segregation of the lot.In practice, one should first disregard segregation problems, and assess sample variability in the segregation-free case. Once the numerical parameters governing this variability have been assessed, then segregation factors can be assessed in turn. In the case of laboratory standard sample preparation procedures, segregation can usually be disregarded altogether."

Jan 1, 1993

By R. C. Snider

The Roy Lloyd Mine in northern Saskatchewan is a high-grade underground gold mine which is currently supplying ore to Golden Band Resources Inc. (Golden Band)?s Jolu mill. Prior to the operation of the mine, an underground exploration program was conducted intermittently at the site. During both the underground exploration phase and mining, Golden Band has implemented water recycling to reduce freshwater usage within the mine in order to address concerns over the potential for impacts associated with freshwater usage and to reduce the volume of effluent discharged from the site. Golden Band initiated an underground exploration program at the Roy Lloyd Mine site (formerly called the Bingo Project) in October 2007 to better delineate the mineralization of the Bingo gold deposit. The exploration program provided geological information required in order to improve the confidence level of the geological resource model and also provided information to aid in the mining of the deposit, such as the determination of groundwater inflow rates. Underground production mining started in March 2011. This paper provides an overview of the mine water recycling methods implemented at the site during both the exploration and initial mining phases of the project, and the success/drawbacks of these measures to date, including the potential cost savings in the form of reduced treatment and monitoring costs inherent in a reduction of the volume of effluent discharged from the site. The paper will also discuss options that are currently being evaluated in order to further assist Golden Band?s ability to recycle water and reduce the volume of effluent discharged to the environment, while ensuring effluent discharged from the site to the environment meets criteria.

Nov 1, 2011

By Garth D. Kirkham, James P. Siddorn, Hendri Falck

"Abstract - As an integral part of the Geological Survey of Canada’s EXTECH III Project, a threedimensional computer model has been created of the Con and Giant gold mines in the Yellowknife Greenstone Belt. The Yellowknife Mining Camp has produced a great deal of gold (over 15 million ounces, or 400 000 kg) in the past sixty years and the prevailing assumption is that the mines are at the end of their lives. However, the potential for discovering additional resources using new ideas and technology, and maximizing use of existing data, offers an opportunity to sustain the old mining operations and maintain their contribution to the community.The objectives of this study included the compilation and creation of a three-dimensional Geographic Information System model (combining 3D subsurface data with surface information) to provide a framework for concurrent structural and alteration studies, and to encourage new exploration in the area. A secondary objective was to retain the data in digital format as a historical reference for future remediation efforts, and to document a portion of Canada’s rich mining history.The end result is a database and set of models that have been instrumental in facilitating further exploration in the area, as well as in developing targets for future exploration and mining activities. In addition, the EXTECH III 3D GIS model has made a valuable contribution toward the understanding of the arsenic remediation issues at the Giant mine, and has served as a tool in support of a variety of highly technical engineering studies and for communicating information and problems to the layman and community as a whole."

Jan 1, 2003