Search Documents

By Alan R. Holt

"This paper provides an overview of the use of uranium and coal in Ontario Hydro's generation program. The dynamics of available supply sources including mining and transportation infrastructures and regional considerations are described. Included is a discussion of needed procurement strategies, both in place and planned, to meet fluctuating fuel requirements while ensuring adequate supply security and cost effectiveness. IntroductionDuring the first half of this century, Ontario Hydro or the Hydro Electric Power Commission of Ontario, as it was then known substantially supplied all of the province's electricity needs from a large number of hydraulic generating stations. Although hydraulic power still provides a very significant part of Ontario energy requirements, this paper will concentrate on the role of uranium and coal in their generation program. To provide a perspective on the importance of these two fuels, Figure I shows the approximate value of each for the past few years in relation to Hydro's total operating costs. The trend toward increasing nuclear output and a corresponding decline in coal use is also clearly illustrated.Figure 2 shows the currently installed capacity of their three main energy sources, hydraulic, nuclear and coal and the 1986 production totals for each, followed by Table I which compares the average operating or running cost on the basis of dollars per megawatt hour for each type of plant. It demonstrates dramatically why Ontario Hydro base load s its hydraulic and nuclear plants, and why coal has become the swing fuel on the system. Although they have a 1200 megawatt plant in Toronto with natural gas-burning capability, and a 2000 megawatt oil-fired station near Kingston, both are presently mothballed and have not been considered in this paper.This paper starts with a user's perspective of the nuclear fuel supply situation which will be discussed in relation to the usual considerations of security, flexibility and cost."

Jan 1, 1988

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline's resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel's ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982

By N. A. McPherson, P. C. Stevens, A. J. Rigby

"There has been a consistent move in recent years to continuously cast small billets while utilizing ceramic stream protection between tundish and mould. The need to have ceramic stream protection has developed from a need to improve billet surface quality by submerged pouring. The need to protect the ladle to tundish stream in conjunction with tundish to mould protection is explained.The continuous casting of thin slabs is at the development state and will require a great deal of ceramic development to ensure the economic viability of the project. An insight is given to the main problems.IntroductionDuring the early development period o f the continuous casting of steel in the late 1940s and 1950s, much of the work was carried out on small cross section products. For example, the continuous casting of 50 mm square billets was carried out on a production scale in the United Kingdom at Barrow. Slab casting was initiated on a production basis on 100 mm thick stainless steel slabs at Atlas Steel, Weiland, Ontario. In the case of slab casting the thickness increased gradually until it was similar to Slabbing Mill feedstock , i.e. in the range 200 mm to 250 mm , although stainless steel continued to be lower at around 185 mm thick.For billets , a significant proportion of steel is now cast at around 100 mm square which creates specific difficulties when casting with a submerged pour - mould powder practice. The move back to smaller cross sections is further emphasized by the current interest in "" Near Net Shape Casting"" . If this move continues, then significant development will be required to create the refractories used between tundish and mould in the continuous casting process.Two specific areas which will receive attention are; (I) the casting of small cross section billet s; and (2) the casting of thin slab."

Jan 1, 1990

By Gerald H. Luttrell, Lance Christodoulou, Jaisen N. Kohmuench, Michael J. Mankosa

The efficiency of the froth flotation process has long been known to be strongly dependent on particle size. For sulfide minerals, good recoveries are typically achieved in industrial flotation circuits for particles in the 30 to 200 µm size range. Particles outside this critical size are typically lost in industrial operations and rejected to tailings streams due to inherent constraints associated with the physical interactions that occur in the pulp and froth phases of conventional flotation equipment. In response to these limitations, a series of experimental studies were conducted to determine whether particles previously lost as tailings could be economically recovered using a suite of novel flotation technologies developed for upgrading ultra-coarse and ultra-fine particles in the industrial minerals industry. For the case of ultracoarse particles, a fluidized-bed flotation system called the HydroFloatTM separator was tested. The data obtained using this novel flotation device in both laboratory- and pilot-scale trials showed that good recovery of previously lost sulfide values up to 850 µm diameter could be achieved. Similarly, for ultrafine particles, a high-intensity cavitation-based column cell was tested. This technology, which utilizes highshear contacting of slurry and gas, was capable of recovering valuable ultra-fine sulfide that were previously lost due to the low capture efficiency of conventional flotation processes. The objectives of this article are (i) to describe the unique operating principles of these two advanced flotation technologies and associated ancillary classification equipment, (ii) to present laboratory- and pilot-scale experimental test data showing the metallurgical benefits of the proposed novel flowsheet for sulfide tailings processing, and (iii) to provide a generic cost-benefit analysis of the proposed system for recovering lost values in existing sulfide tailing streams.

Jan 1, 2016

By André Bérubé

"IntroductionSince the disappearance of Les Forges du Saint-Maurice at the end of the last century, many historians have taken an interest in the lengthy past of this enterprise. They considered the political, socio-economic, administrative and anecdotal aspects of the industry, but barely dealt with the elements of technology. The purpose of this article is to try to fill this gapru.Les Forges du Saint-Maurice was an integrated industrial concern, specializing in the production of semi-finished wrought iron and finished cast iron, that operated almost without interruption between 1734 and 1883. Les Forges first came into being in 1729, when Montreal merchant Francois Poulin de Francheville submitted to the king of France a request for the right to exploit the bog iron ore deposits on his seigneury of Saint-Maurice. This request, agreed to in 1730, was one of a long series of attempts, previously unsuccessful, to establish a local iron industry in the colony. Several such proposals were held up by a lack of capital from promoters or a too rigid application of the mercantilist policy by the metropolis. In 1730, however, the French minister Maurepas favoured a more liberal policy which would encourage private enterprise. The benefits of an iron industry to the naval construction industry was a factor that caught the attention of administrators. The choice of the site for Les Forges was based on the following factors:• the abundance of surface deposits of bog iron ore in the Saint-Maurice region;• the presence of a vast supply of hardwood and conifers needed in large quantities by this industry;• the proximity of sandstone and limestone deposits, indispensable materials for the construction and operation of the blast furnace;• the presence of a water stream, with sufficient flow to provide the hydraulic power needed for the operation of the machinery."

Jan 1, 1983

By T. Yalcin

"This paper describes a study carried out to determine the behaviour of Cu-Ni mill tailings during natural and flocculated sedimentations. Settling rates were examined under various conditions through standard laboratory batch settling tests. Flocculation was found to improve the sedimentation process significantly, but its effectiveness depended on several factors such as the pulp density of feed, the type and dosage of flocculating reagent, the pH of pulp, the intensity of mixing flocculant with tailings sand the use of stirring during compaction.It is shown that. for a sedimentation process taking place under given conditions, underflow pulp density (P) and sedimentation time (t) are related by the expression P = k.tn, where k and n are constants. A procedure is described for the use of this expression in thickener size estimations. IntroductionOften a considerable proportion of the mill feed is disposed as tailing, because the valuable mineral recovered usually forms a small fraction of the ore. Moreover, wet concentration processes result in liquid wastes that are several times more voluminous than the ore itself. Thus the handling and disposal of these wastes become an important cost item in most milling operations. The principal unit process employed in tailing disposal is solid-liquid separation which is traditionally carried out by gravity sedimentation in thickeners or tailing dams. Direct disposal of tailings into tailing dams is common practice where sufficiently large areas of land are available but it frequently becomes more economical or practical to densify the tailings in a thickener beforehand.Successful thickener operation depends essentially on correct thickener size which is in turn governed by the sedimentation characteristics of the tailings handled. Flocculation can aid the sedimentation process and bring about significant savings in thickener size, but its effective use requires a detailed study to identify the optimum conditions of application."

Jan 1, 1988

By S. P. Jekielek

"This paper describes the automation of a mine hoist ore loading pocket using a programmable controller. It provides an introduction to programmable control, and outlines the various modes and operating sequences of the loading pocket. A comparison is made with previous equipment to illustrate the increased flexibility, reliability and diagnostic functions that are gained.IntroductionLoading pockets have evolved from a couple of manually operated air cylinders to entirely automated systems. Early pockets were usually formed in rock, with loading and discharging regulated by air-operated gate s. Interlocks, added to this arrangement, prevented simultaneous operation of the gates and ensured proper hoist position . As the loading pocket advanced, it was recognized that gravity feed posed problems, often becoming plugged or letting water run through into the shaft. A belt conveyor was employed, eliminating the se problems and resulting in greater loading control. Weighing the combination of transistorized logic modules, replaced many relay systems. This elimination of moving parts and contacts increased reliability and reduced maintenance costs.As semiconductor technology progressed, there were major breakthroughs in miniaturization and reliability, and as a result the programmable controller was introduced. Programmable controllers first appeared in the automotive industry in the late 1960's. A system controller was required to replace the large relay panels in operation at that time. The use of digital integrated circuitry enabled these programmable controllers to automate processes with hundreds of inputs and outputs. Advances in electronics reduced production costs , making controllers for smaller application s viable . This development is on-going, each generation introducing controllers with greater capabilities for a wider variety of systems. equipment was the next step in loading pocket development, and dependance on much of the manual control was reduced . The complete system was first automated using relay panels. Solid- state devices were later introduced, and static control,"

Jan 1, 1980

By A. L. Craven, J. P. L. Bacharach, D. B. Stewart

"Inert gas use for underground mine fir e control is a well-established mature technology in some parts of the world. This paper reviews three candidate inert gases and describes three case histories where inert gas fire-fighting technology was used in actual underground fires.IntroductionInerting is the introduction of an inert gas into an atmosphere in contact with a fire to reduce the level of oxygen and hence the intensity of the fire 10 the point of extinction. The benefits of inerting include:a. Reduced Explosion HazardBy displacing oxygen from the atmosphere surrounding the fire the risk of secondary gas explosions is reduced. For example, simple methane-air mixtures at standard temperature and pressure are non-explosive below 12% oxygen. In actual mine fires, combustible gases may include hydrogen and carbon monoxide as well as methane. Such gases are also rendered non-explosive with oxygen removal to below 40/0. Fuel-rich oxygen-deficient mixtures can however be made explosive through dilution with air. Such dilution can occur downwind of the fire. It is also important to remember that the atmosphere in a sealed-off fire zone is rarely homogenous.b. Reduced Fire Intensity and SpreadIn a fire zone the initial combustion may well set alight materials surrounding the fire. Inerting can reduce the intensity and spread of secondary combustion and can cool the area surrounding the fire zone after the fire itself has been extinguished.c. Reduced Air LeakageLeakage of air into sealed areas in excess of the natural leakage may be reduced either by introducing inert gas into the leakage paths to replace air or by pressure balancing seals and providing a chamber of nitrogen on the outbye side of the seals. Both methods assist in the reduction of the intensity of combustion and hasten oxygen starvation."

Jan 1, 1986

By T. R. Yu, D. B. Counter

"Kidd Creek Mines primarily employs sublevel blasthole stoping for underground mining operations. During pillar recovery in No.1 Mine and panel mining in No.2 Mine, the free standing fill exposures may reach a height of 100 m or more. Consequently, a competent consolidated rockfill has been required to fill the mined openings.Since 1976, a total of more than fifty stopes and pillars have been filled with over four million tonnes of backfill. Fill exposures, up to heights of 100 m, have stood up well after blasting adjacent to the backfill.The fill material consists of a graded aggregate, Portland cement and ground slag. Sand has been occasionally mixed in the fill material to serve as avoid filler. The aggregate is prepared in a fill crushing plant, transported underground through raises, and hauled to the filling stopes by conveyors in No. 1 Mine and by trucks in No.2 Mine.Two mixing methods are currently in use. No. I Mine utilizes the free fall of gravity; the fill materials are sprayed with cement slurry as the aggregate departs from the conveyor into a mixing culvert. The other is the use of a rotary mixer on a batch basis in No. 2 Mine.This paper describes the fill systems, filling operation s, and the backfill quality control practice, together with various testing results related to improving fill quality as well as reducing fill costs.IntroductionThe Kidd Creek minesite, located 27 km north o f the city centre of Timmins, Ontario, produces 4.5 million tonnes of copper, zinc, lead, and silver ores annually from its No. 1 and No.2 underground mining operations. Both mines employ a sublevel blasthole stoping method."

Jan 1, 1983

By T. D. Brown

"A review of the current status of gasification technology shows that many engineering systems are immediately available for use in the gasification of coal. Widespread international experience can be brought to bear on the atmospheric pressure gasification of all Canadian coals.Unless a high ash content dictates the use of a fluid-bed gasifier, it appears that bituminous coals can be used in gravitating (fixed] bed systems and that the strongly caking coals are most suited to the high-pressure entrained-bed systems . Existing and developing technologies in fluid-bed gasification are attractive for reactive lignites and subbituminous coals.The Fischer-Tropsch based process is the only commercial embodiment of coal liquefaction; the use of Canadian coals in this process depends only on their gasification characteristics. Current developments in hydroliquefaction are directed toward carboniferous coals of medium or high rank. It is not clear that cretaceous coals of the same rank will give similar process yields and economics.IntroductionThe twin coal conversion processes of gasification and liquefaction have a history which dates back beyond the current energy shortages of the western world. Indeed, liquids and gas from coal were produced before this century.Coal gas produced from a coal carbonization process was originated before 1800, and the development of gasification of non-coking coals was patented by Siemens in 1860.This patent represented the first use of air and steam together in the gasmaking process. The pioneering development of coal gasification Using oxygen and steam was demonstrated by Lurgi in the late 1920s. This historical sequence was all carried out at atmospheric pressure, and it was not until the immediate pre-war (1939/45) years that operation of the coal gasification process at elevated pressure became a reality."

Jan 1, 1981

By P. R. Goad

"Kidd Creek is a large volcanogenic base metal sulphide deposit, located near the west end of the Abitibi greenstone belt, 27 km north of Timmins, Ontario. The rhyolite geology is characterized by a NNE-striking and steeply east-dipping package of rhyolite volcaniclastics upon which has been imposed a strong ESE-striking and north-dipping structural fabric . Massive rhyolite units with grey-black. chloritic cores and yellow, sericitic margins intrude as dykes into the stratigraphic footwall and as sills higher in the stratigraphy. Massive rhyolite units positioned near the top of the felsic pile exhibit an extensive marginal development of hydraulic fracturing and are termed crackle-brecciated rhyolite.The stringer sulphide zone is positioned in a lobate blanket of crackle-brecciated rhyolite at the top of the felsic pile. The stringer sulphide zone is characterized by a mature chemical alteration, being specifically depleted in alkalis and enriched in iron-rich chlorite. with accompanying silica, sericite and carbonate alteration. A suite of trace elements characterizes this mature alteration. The massive rhyolite units, which intrude lower in the rhyolite volcaniclastics, exhibit a core of weak chlorite alteration and strong marginal sericite alteration. Tight or unfractured massive rhyolite units are essentially devoid of sulphide mineralization and exhibit a suite of trace elements characteristic of this immature alteration. It is interpreted that the massive rhyolite units intruded into an already evolving system and ""choked-off"" active conduits carrying hydrothermal fluids and subsequently acquired an immature alteration signature. Rhyolite units positioned higher in the pile developed intense hydraulic fracturing and a mature alteration coincident with the formation of the stringer sulphide zone. In summary, a model, based strictly upon the rhyolite geology, is reviewed to assist in the exploration for volcanogenic base metal sulphide deposits."

Jan 1, 1985

By K. N. Karparov

?Two highwall failures in a South African coal mine defied analysis by widely accepted limit equilibrium methods. ?The geological conditions were complex, with undulating coal-bearing strata overlying a karstic topography formed in underlying dolomite belonging to the Transvaal Supergroup. ?It was clear that the simplifying assumptions made by all limit equilibrium methods were inappropriate in the conditions.

May 1, 2007

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e., fewer energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant. INTRODUCTION Solar energy can help make mining more sustainable (Moreno-Leiva et al., 2017). With falling battery costs, an autonomous solar supply is soon to become an economical alternative in many parts of the world, even in the presence of a larger power grid (Child et al., 2017). Although this, places with high solar radiation such as the Atacama Desert in Chile, nowadays show a large potential of incorporating solar energy as a supply of energy. Many of the Chilean copper mines are in this zone making it interesting to study their compatibility and potential of integrating this renewable source to their operation. The power demand in a copper mineral processing plant is determined by the main power loads in grinding and flotation, with grinding typically the largest power consumer, especially the semi-autogenous grinding (SAG) mills (Wei and Craig, 2009). In Chile, it corresponds on average the 50% of the electrical energy consumption (COCHILCO, 2013). Solar energy production is determined by the irradiance perceived into the solar photovoltaic (PV) panels (which varies through the geographic location) and several other climatic parameters such as the current season, humidity, temperature, altitude, and others (Molina et al., 2017). Also, solar energy is only generated during the sun hours, getting to a maximum generation at a certain peak hour during midday, and finally dropping to zero during the night. This shows a cyclic parabolic profile as shown in Figure 1. Due to the SAG mill operated continuously, the power supply always must be available. During the night, to continue supplying the energy, it is necessary to complement the solar power generation with a battery energy storage system (BESS), which will act as a power backup and a buffer. For the optimal sizing of this PV- BESS system, information of the demand profile is needed (Pamparana et al., 2017). In the case of the SAG mill operation, the resulting demand relates to the ore-hardness for a specific throughput and grind size (Morrell, 2004). Therefore, for a given throughput and target grind size, a harder ore would require more power, and variable hardness results in more variable demand and a subsequent need for larger energy storage (Bueno et al., 2015). Due to the ore-hardness variability and the operation of the mill, the power demand profile in inherently variable.

Jan 1, 2019

By W. P. Clement, M. C. Bell

"PT International Nickel Indonesia, a subsidiary of Inco Limited, mines and processes nickel laterite ores for the supply of nickel matte, primarily to the Japanese market. It has large ore reserves and a substantial portion of its energy requirement is supplied from its own hydro-electric plant. Since the early 1980s, the company has increased its production level and has dramatically reduced its unit costs. Projects are in progress to further decrease costs and recently a major expansion - 31% increase in nominal capacity - has been undertaken, consistent with marketing opportunity in Japan. The expansion project, which has a low capital cost per unit of production, is outlined in this paper.IntroductionPT Inco is a fully integrated mining and smelting facility located in Indonesia on the island of Sulawesi, and is based on a very large, world class nickel laterite orebody located 60 km inland from the Gulf of Bone. Construction of a single furnace line plant started in 1973. Complete supporting infrastructure of townsite, hospital, schools, shopping centres, road systems, and an airport, all had to be built. Prior to completing the first phase, the decision to expand the plant to a three kiln-furnace line was made. A major factor in the decision was the ability to develop the hydroelectric potential of the nearby Larona River. This involved construction of a 30 m high dam, and a 7 km surface canal to the generating station. The penstocks drop 150m to three 55 Mw turbines. The power generated is sufficient to supply the entire electrical load for the complete smelting complex and town site. The unique capability to supply the high smelting energy requirements for a lateritic nickel ore by fully captive hydro power, has, over the past decade insulated PT Inco from the large upward swings in oil prices suffered by other lateritic nickel producers.Wet ore is first partially dried to 20% moisture in two co-currently fired rotary driers, screened on an internal trommel, and delivered to two dry ore storage buildings. The partially dried ore is calcined at 750°C and partially reduced in three large 100 m by 5.5 m kilns. Reduction is accomplished by lancing bunker C oil onto the ore bed at the discharge end of the kiln. The kilns are equipped with five air pipes with onboard blowers to gradually bum the combustible gases generated by the lance oil. The kilns were also originally equipped with two side burners to supply additional heat close to the feed end of the kiln. Calcined ore is transferred by 20 ton refractory lined containers to the furnace feed bins at the top of the smelter. Smelting is carried out in three 18 m diameter furnaces powered by 45 Mw transformers. Slag is skimmed at 1550°C through water cooled breast plates and removed to the slag dump by Haulmaster Carriers. Matte of 25% Ni, 1O% S, 65% Fe is tapped at 1350°C into the converter aisle. The iron is slagged in converters to produce a nickel sulphide matte at 80% Ni. Three rotary Kaldo converters were initially installed. The product matte is granulated, dried, and shipped in returnable rubber bags to Japan. Most of the matte is fluid-bed roasted to nickel oxide and then directly reduced in a second reducing fluid bed reactor at our facilities in Japan.The smelting complex was designed to smelt two million tonnes of dry ore per year, equivalent to 34 000 tonne nickel production at an ore grade of 2% Ni. The cost of the entire project including working capital was $900 million."

Jan 1, 1990

By J. P. Nowlan

"This paper is an attempt to outline the structural problems at the Cochenour Willans mine, in so far as their details have been tentatively worked out. It must be emphasized that there are considerable data that can be interpreted in more than one way, and that further work may modify or completely change some of the hypotheses presented herein. Certain features, however, are sufficiently constant to warrant reliance on them when searching for extensions of orebodies.As the individual ore shoots usually have relatively small dimensions, but are often very high grade, structural details are of more than usual significance in laying out a mining programme. An illustration of this is a small shoot recently located and mined as a result of studying a minor slip cutting off a part of high grade gold ore in No. 319 stope. The shoot, which is bounded on three sides by slips, and on the fourth by the original stoping, was roughly triangular in plan, 20 feet on the base, and 40 feet in length. The average width mined was 4.5 feet, but the gold obtained totalled over 1,800 oz.The property lies in Dome township, east of McKenzie island, and consists of an original group of thirteen claims acquired from the Cochenour Willans syndicate, plus one additional group of five claims obtained by purchase from the Kelson Red Lake Gold Mines, Limited, and one other claim that rounds out the southeast corner of the block.The claims of the original group were staked by W. M. Cochenour, Dan Willans, and Horace Young, during 1926 and 1927. The Cochenour Willans Syndicate was formed in 1928, and until incorporation of the present Company work was carried on at varying intervals by several different interests, including Ventures Limited, Hollinger Consolidated, who sank a shaft to open up the 150-foot level, and by the Syndicate itself. The first ore from the property was shipped to the Gold Eagle mill by the present Company in 1939, and amounted to 4,959 tons, from which 2,360 oz. gold was recovered. The first brick was poured in December, 1939, and production has been continuous since that date. To the end of June, 1946, gold having a value of $5,982,000 has been produced from 345,033 tons of ore treated."

Jan 1, 1954

By A. E. Aho

"The Pacific Nickel property lies 7 miles northwest of Hope and 100 miles east of Vancouver, in the Coast Mountains of southwestern British Columbia. Nickel-copper sulphides were discovered in ultrabasic rocks on this property in 1923 and the deposits were explored by Pacific Nickel Mines until 1937, then again between 1951 and 1954 by Pacific Nickel Mines and by Newmont Mining Corporation through its subsidiary,Canadian Ore DepositsWestern Nickel. The property was studied by C. E. Cairnes (1) in 1924, by W. E. Cockfield and J. F. Walker (2) in 1933, by H. C. Horwood (3), (4) in 1936 and 1937, and by the writer in 1951 and 1952. Except for a few thousand tons for trial shipments, the property has never been mined. Indicated ore reserves now total somewhat over one million tons averaging about 1.4 per cent nickel and 0.5 per cent copper, with lesser values in precious metals and cobalt.GEOLOGIC SETTINGThe nickeliferous ultrabasic rocks form part of the core of a 15-milewide block of Late Palæozoic metamorphic rocks and Mesozoic intrusives which extend north-south between the coast batholith of British Columbia and the Chelan batholith of Washington. Margins of this block are faulted in part against less metamorphosed volcanic and sedimentary rocks largely of Jurassic and Lower Cretaceous age (Geo/. Surv., Canada, Map 737 A, 1942). Serpentinites, suggestive of deep transgressive structure, occur within the block, and also at its east margin along faults which are southern extensions of the regional Yalakom-Fraser River fault zone. Some of the other mineral deposits in the Hope area appear to be spatially related to these major faults.The mineralization at Pacific Nickel occurs almost exclusively within a stock-like mass of ultra basic rocks which mingle with, and partly cut, a larger batholithic mass of genetically related diorites and norites of late Mesozoic age (Figure 1 ). The ultra basic mass consists essentially of fresh, medium-grained hornblendic pyroxenite with peridotitic cores and with a remarkable margin of pegmatitic hornblendite. The most hornblendic rocks appear to be chiefly products of reaction and replacement of the pyroxene and olivine rocks. The mineralization consists of disseminated and massive pyrrhotite, with subordinate pentlandite and chalcopyrite, amongst fresh olivine, bronzite, and, Jess commonly, augite and hornblende. Both the ultrabasics and mineralization are cut by small hornblenditic and dioritic dykes, and by veins and alteration zones."

Jan 1, 1949

By G. Granata, C. Tokoro, M. Matsuoka, K. Horiuchi

"Given the high demand of copper and the lack of new high-grade deposits, low grade copper ores containing copper oxides and refractory sulfides need to be processed as well. However, in order to recover copper from refractory copper ores, the leaching performances should be improved. In this study, we investigated the effect of the mechanical activation in the leaching of copper from covellite. The influence of a mechanical treatment by planetary ball milling on leaching rate in sulfuric leaching media was evaluated by using X-ray diffraction (XRD), mineral liberation analysis (MLA) and X-ray absorption fine structure (XAFS). Results showed a significant increase in copper leaching from around 50%up to 100% along with an improvement of the leaching kinetics when using planetary ball milling. XRD spectra showed the disappearance of the covellite peak from (101) face, thus suggesting the amorphization of covellite associated with the use of planetary ball milling. XAFS results showed that the coordination number of Cu changed from 6 to 3, thereby confirming the effectiveness of the mechanochemical effect.INTRODUCTIONDuring the last decades, while the copper grade in copper ores has been decreasing, the concentration of impurities such as arsenic tends to increase, thus requiring for the processing of low grade copper ores. For a suitable processing of copper minerals, hydrometallurgical processes are preferable due to the lower costs, the lower environmental impact and the easier implementation (Watling, 2006). However, for an economical recovery of copper, the leaching performances must be improved.Among the recent advancements in leaching technologies, the mechanochemical activation allows for an improvement of the leaching performances by means of high-intensity grinding(Mohammadabad et al., 2016). In the first place, the improvement is the result of the dramatic decrease of particle size, which results in an increase of the mineral surface area and the consequent enhancement of leaching kinetics. Furthermore, the intense mechanical stress due to the high-intensity grinding could induce the rupture of the crystal structure producing a decrease of crystallinity. Such changes of the mineralogical structure, also known as mechanochemical effect, can lead to more leachable mineral, thereby resulting in a greater dissolution of copper. Last but not least, whereas the mineral surface might undergo passivation during leaching, the high-intensity grinding can continuously refresh the surface of the mineral, thus exposing portions of unleached bulk mineral."

Jan 1, 2017

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

By E. Hinton, L. Bloomquist

"This paper describes a guidance system for autonomous underground mining vehicles, which does not require any infrastructure or inertial positioning systems to aid the guidance process.BackgroundINCO Limited mines approximately ten million tons per annum through 12 operating mines in the Sudbury, Ontario, area (Fig. 1). With challenges from operating in a cyclical marketplace as well as new technologies making alternative nickel ores more competitive to refine, the Mines Research department embarked on a strategy that pointed toward automation as a tool to help the company become even more economical in mining.The mining industry has been looking for ways and means to mine orebodies more and more inexpensively. Automation and the lessons learned from manufacturing had a great influence in the direction of research at INCO Limited over the past ten years. Guidance systems have evolved over the years but the majority of commercially available systems rely on some form of infrastructure. This, in part, has caused some resistance from operators to install and maintain automated or semi-automated systems for guidance of underground machinery.Internal industrial studies cited travel time to and from the workplace as one of the major time sinks in the shift of underground miners. Depending on the mine, it may be as much as two hours moving in and out of an area. Some work areas have accommodated this by having “hot changes” at the work place. However, at some point in time, there are two people tasked with the same job and on site at the same time to make this overlap occur.Tele-operation of underground hard rock equipment eliminated this overlap and also provided a comfortable environment in which to work. By taking advantage of the communications network installed, the miners proved that they could operate three machines with relative ease. This was accomplished by a vision-based, “painted line,” autonomous guidance system termed the light rope system.With a few years’ experience with the system, some issues have arisen, including the cost of the rope itself (Fig. 2).The vehicle’s route is limited to the paths defined by the light rope, and a system of switching power to the light rope to select different routes is required. The rope itself is subject to damage from nearby blasts. Also, the system offers no obstacle detection; the vehicle may be switched off as a means of shutting the machine down thus protecting personnel in the area."

Jan 1, 2001

By A. V. Corlett

MR. C. S. Gibson: Mr. Chairman, I listened with much interest to Mr. Corlett's paper. Those of us who are directly engaged in mine ventilation and dust control are impressed by the improved atmospheric conditions to be derived from the use of methods of mining such as those in operation at Aldermac, which Mr. Corlett has just described, and those employed at Noranda. It is a well known fact that drilling-dust is one of the most potent factors in the production of silicosis in mines handling ores containing quartz, so that from that angle the use of diamond drills, instead of percussion drills, to drill ore for blasts in stopes is an important development. A second point which I think merits mention is blasting. Blasting, we all know, creates the most dust in a mine and the fact that you can drill ore for a large blast with diamond drills and fire it, say, on Saturday night, and then have all the next day to ventilate the workings, is a great advance in dust control. 1 have wondered if Mr. Corlett, or possibly those at Noranda, can en-vision the use of the diamond drill as a means of advancing cross-cuts and drifts, preparing stopes, etc. I believe it is a matter which is receiving considerable attention at the moment in some parts of the world and J thought it would be interesting to have Mr. Corlett's reaction on that point. MR. A. V. CORLETT: I am not quite so hopeful of using diamond drills as a means of drilling holes in the ordinary drift. Maybe some of the diamond drill men can give us some further information on that point. MR. R. D. LoNGYEAR: The diamond drill manufacturers are working on that problem, but until further work is done we have nothing definite to offer. Drilling holes with a diamond drill to compete with rock drills for advancing drifts and cross-cuts is a desirable objective, because of the elimination of drilling dust and the ability to cut a smooth bore of uniform diameter. To reach this objective, higher rates of penetration are required, which can only be achieved by discovering the optimum bit rotating speed, by reducing vibration, and by further improving the bits and machines. We are optimistic, but the problem is still largely in the research stage.

Jan 1, 1940