Search Documents

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By China University of Mining and Technology, P. Zhang, C. Zhou, C. Duan

"Recovering pyrite from the gangue with high sulfur content is of great significance for both economic development and environment protection in China. Due to the global water shortage and high cost in wet separation processes, it is urgent to explore more efficient energy and water conservation method in mineral processing field. This study has proposed an innovative method based on density difference for fine pyrite enrichment by vibration fluidized bed. In this study, the total sulfur content (TSC) of the gangue sample is 19.18%, and the pyrite is disseminated with fine granularity in the gangue which should be crushed for dissociation. The combination and dissociation experiment of -6mm gangue shows that the dominant density of -6+3mm, -3+1mm and -1+0.5mm comminuted material is +2.9g/cm3. Based on the analysis of characteristic, the effects of various factors on the separation performance were experimental studied. The results show that gas velocity, vibration intensity and bed height all have the significant effects. With the increases of superficial gas velocity, vibration intensity and bed height, the separation performance all presents a decreasing tendency. Additionally, the TSC of -6+3mm, -3+1mm and -1+0.5mm materials are respectively up to 37.94% , 35.43% and 30.61% at the optimum conditions, which are the 1.72?1.90 and 2.29 times as much as the TSC of raw material, respectively. This study demonstrates the vibrated fluidized bed can recovery pyrite from the gangue effectively.INTRODUCTIONWith the increasing mining and separation of coal, the yield of gangue has a further growth tendency, which has become one of the largest reserves of industrial waste (Querol et al., 2008). However, many harmful elements, such as S?NOx and Hg, is existed in the gangue leading the serious damage to the soil and environment (Hao, Yun, Zhanyuan, Sen, & Song, 2013). In addition, the economic would be suffered from the loss resulting in the occupied of arable land caused by the accumulation of gangue (Yeheyis, Shang, & Yanful, 2009; Zhou, Liu, Yan, Fang, & Wang, 2012). Therefore, the government has put forward the policies of ""green mining"" in China (Xing & Gao, 2009; R. Zhang, Ai, Zhou, Ju, & Zhang, 2015; Zheng, Du, Li, Qiu, & Yang, 2015). Among different research areas of coal utilization, extracting the useful minerals has become one of hot topics (Ledin & Pedersen, 1996; P. Patra & Natarajan, 2003; Partha Patra & Natarajan, 2004). At present, many researchers has devoted to the desulfurization of coal all over the world. As result, the sulfur element, which is mainly existed in the presence of pyrite, would transferred in the tailings, namely the gangue. Meanwhile, the pyrite is important raw materials to produce rubber, paper, textile and match. Consequently, recovering the pyrite from the gangue is not only suitable to the requirement of ""green mining"", but it could turn the waste into the treasure having the important significance."

Jan 1, 2016

By Mauricio Olivares

About Largest combined Phosphate and Potash company in the world Corporate headquarters in Plymouth, Minnesota Publicly traded on NYSE under MOS

Aug 1, 2013

By T. C. Murphy, W. Taciuk

In 1966, the Iron Ore Company of Canada commissioned a wet magnetic scavanging plant for the recovery of fine magnetite values p.resent in spiral tailings discharged from a spiral gravity separation process. The plant includes dewatering, grinding, classification, thickening, mini-wedge screening, and primary, secondary and tertiary wet magnetic separation stages. The source of feed varies in quantity and quality, so the original design included variable operational procedures to deal with these conditions.

Jan 1, 1972

By R. L. Brown

The burning sulphide ores in the Sullivan Mine generate sulphur dioxide gases. This paper is concerned with a description of the environmental impact of SO2 on air quality in the mine and on the surface in the vicinity of the mine. As a result of surface caving, SO2 has been able to vent to surface and winds have carried it into one residential area of Kimberley. Monitoring practices are described.

Jan 1, 1977

By G. A. Moruzi

Two sulphide dust secondacy explosions have occurred in the mines of the SUdbury operations of Falconbridge Ltd. during the past 18 months. 'Ihe main similarity between the occurrences is that they both happened in vertical crater retreat blasthole stopes. A relatively high p:,v.tier factor was noted in both instances. other details are enumerated and examined, as well as some results of tests done by Noranda Research on company ore samples.

May 11, 1988

By D. MacGREGOR, VERA TUREK

The Badgeley Island quartzite deposir in Georgian Bay is worked by lndusmin Limired and was developed in 1969 to produce a high-qualiry silica for use in rhe ferrosilicon and glass industries. The quartzire is part of the Precambrian Bar River Formarion, and is a generally whire, fine-grained rock containing rhin sericire seams. Primary sedimenrary features wirhin the deposit are bedding and ripple marks. Amphibolite and diabase dykes cur the quarr zire body.

Jan 1, 1984

By D. J. Kemp

The 20th century saw changes in the mining and metallurgical industry not only technically but also in social and environmental expectations. As projects continue to become larger their visibility raises concerns among many groups. For mining companies, transparency, openness, and early engagement of all parties are fundamental to assure success. An equally important task is to anticipate the standards that will be required to meet society’s expectations in the 21st century.

Jan 1, 2005

By Peter D. Cunningham

At Vale Inco in Sudbury, underground mobile equipment production and maintenance data is presently collected manually from paper slips. This paper reviews a pilot project that developed a system to electronically collect that data. The benefits and improvements in data accuracy, timeliness and reduction in collection effort, will be discussed. Technological issues that arose from the use of WiFi, RFID (Radio Frequency Identification) and the IREDES mine data equipment standard are also discussed.

Oct 1, 2009

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017

By Jerry C. Tien, Yingjiazi Cao

"Coal spontaneous combustion (SponCom) is a natural phenomenon in underground operations, which can either happen naturally or be triggered by human activities. For underground operations, espe-cially in coal, SponCom can happen frequently as a result of air leakage, although its incubation period may vary depends on types of coal and surrounding environment, resulting in uncertainty in control. In China, most of the underground coal operations now use longwall mining method because of its superior safety, high productivity and efficiency. With an increased popularity, there is also an increasing necessity to study spontaneous combustion, its occurrence and management. There have been many theoretical analysis and experimental studies over the past half century hoping to understand the occurrence of coal combustion and its control measures to better understand the occurrence and to design controlling measures to limit the dam-age it causes. In this paper, research on coal spontaneous combustion fundamentals from these three aspects will be reviewed, gaps highlighted and possible directions for future studies. INTRODUCTION The history of anthropic development is the history of human's energy utilization progress. From the first usage of fire, people have been continuingly seeking energy resources on earth. Coal, as an abundant, economic and convenient source of fuel quickly became indispensable and made significant contribution to economic growth worldwide. With technology and societal development, people are becoming more and more coal-dependent, but at the same time, problems of fossil fuel combustion came into sight. In global coal mining industry, spontaneous combustion has now presented one of the most challenging safety issues, it is also believed that it has contributed significantly toward the climate change. It is essential that more effort be invested to examine the cause of SponCom and its control measures. Coal SponCom is a complex process, with both physical and chemical inter-actions among various interrelated factors such as local airflow distribution, ventilation pressure, methane emissions (if any), and physical surroundings underground. With the advent of powerful computers, simulation techniques and af-fordable modelling packages in recent years, significant advances have been made in understanding sponta-neous combustion. But because of the complex nature of combustion and varying underground conditions, there are still areas that need further examining. This paper will focus on illustrating the current research of coal spontaneous combustion and addressing research gaps and future study areas."

Jan 1, 2019

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By Michel Aubertin

Mining activities can produce large volumes of waste rock, which are typically deposited in piles on the soil surface, above the water table. Such piles can cover areas of several tens of hectares and can reach over a hundred meters in height. For hard rock mines, the waste rock grain size can vary from silty particles to metre-scale blocks. The internal structure of a pile constructed on a relatively flat surface typically includes two main zones. The first zone corresponds to the heart of the pile, and is formed by several sub-horizontal stratifications (with dense and loose layers) due to the heavy mine equipment traffic which induces local compaction and degradation of the waste rock. The second zone corresponds to regions where waste rocks are deposited by push-dumping or end-dumping close to the external flank of the pile, inducing grain size segregation along the slope. Depending on the deposition sequence, grain size distribution and bench height, a gradation may then be observed, with coarser particles (with cobbles and blocks) near the base and finer particles near the crest, together with inclined stratifications due to the advance of the deposition face. These internal features affect the distribution and flow of water (and air) in the pile. To assess the internal distribution of material properties within the pile, a combination of several tools is usually required which can provide information on the hydrogeological and geochemical characteristics of the waste rock. In this regard, geophysical tools are very interesting because they can lead to a threedimensional mapping of property variations. The information gathered from a combination of appropriately selected techniques can be used to construct numerical models to further study unsaturated water flow and reactive transport. Such simulations help better understand the pile response in its actual and future states, which in turn provides input to adjust the deposition sequence, to plan for closure, and to select an in situ groundwater monitoring strategy. The presentation will give an overview of techniques that have been developed to characterise material properties in the laboratory and in the field, and to obtain a general picture of a pile?s internal structure. Additional results on unsaturated reactive transport modelling will also be shown to illustrate how the internal pile structure may influence its hydro-geochemical and environmental response.

Nov 1, 2008

By Donald Roberts

"Parameters f or design and development of an emergency hoist system (Fig. I) were submitted to Timberland Equipment Limited of Woodstock, Ontario by the Potash Corporation of Saskatchewan Mining Limited.The unit is the first of its kind in Canada. Not only does it comply with the province of Saskatchewan's mining regulations, but has the added advantage of being completely mobile and self-contained.As well as being useful in the mining industry, the mobile hoist unit could be used in other emergency situations such as rescuing people trapped in wells.JustificationRevisions to the Mines Regulations under Section 13 of the Occupational Health and Safety Act, 1977, of the Province of Saskatchewan stipulate as follows:"" Section 410 .04(4) The Mine Employer shall make adequate provision at every mine where any worker is hoisted in a shaft not equipped with a manway to enable an y such worker trapped in a conveyance in the shaft to be rescued . "" It was not possible to equip the shafts at PCS Mining' s Divisions with "" manways"" and therefore an alternative was required.BackgroundThe Potash Corporation of Saskatchewan Mining Limited, a subsidiary of the Potash Corporation of Saskatchewan, operates four potash mines. Of these, three, Cory, Rocanville and Lanigan Divisions are wholly owned while the fourth, Allan Division, is 40% owned by Kidd Creek Mines Ltd., but managed by PCS Mining. The four underground operations all have a service and production shaft.From 1979 to 1981 the PCS Mining Division, along with Central Canada Potash, were developing an idea to use the existing ground-mounted timberland hoist at Lanigan as an emergency hoist. This hoist was used in the past for rope-up work at both Rocanville and Lanigan and other potash mine s. The Department of Labour at this time had concerns about the time it would take to load, t ran sport and re-install the hoist on a foundation when needed for an emergency. Weight and size made this particular unit very cumbersome for transporting.In addition, the speed at which this hoist operates is too slow for rescue work. When the Department of Labour expressed concern that this unit would be unsuitable for these rea sons, a search for a suitable unit was initiated.The project responsibility for procuring an emergency hoist for the Potash Corporation of Saskatchewan Mining Limited was assigned to the author, a shaft/ hoist specialist a t PCS Mining."

Jan 1, 1986

By E. Henderson

"This paper outlines the upgrading of a double-drum 2000 hp cage hoist to provide fully-automatic operation from shaft station control panels. The application utilizes programmable controller technology to provide all necessary functions for movement of personnel and material to 22 locations in a 4000 ft shaft.Various functions involving special design considerations such as ""chairing"", ""jogging"", and three modes of ""multi-level calling service"", are outlined. The use of higher level PLC functions to optimize memory utilization and simulate ""elevator service"" required the addition of a comprehensive fault finding software section to aid in troubleshooting.This paper will deal primarily with the automation portion of the project with references made to other pertinent aspects which were prerequisite to automatic operation. It is not intended to deal with every design detail, but rather to provide an overview of what can be done in the area of automation for those considering such an application. INTRODUCTIONEarly hoisting control systems provided only the essential elements of control, leaving many responsibilities with the operator. With advancements in various areas of technology, electromechanical devices were incorporated to enforce slow-down in end zones, control acceleration rates, monitor safety devices, etc. Brake control systems were supplied to allow for ""single-stick"" operator control, regulated deceleration during emergency brake applications, etc.These additions enhanced the over-all performance but were generally confined to speed and current regulation. Some mechanical devices, such as travelling nut limits, etc.; were used to provide ""position"" control to multiple locations within the shaft. These devices, in conjunction with rather extensive relay control panels, did allow for the establislunent of some automatic cage hoists . The hoists were often limited to service from point ""A"" to point ""B""', involving a limited number of levels due to the complexities of the mechanical interfaces employed. Only limited systematic work sequences were possible . .Programmable Logic Controllers (PLCs) were introduced into industry in the mid-70s and have since gained acceptance in mining applications such as pumping, ventilation, ore handling, etc. This technology, being ""software"" based, allows complexities to reside in the program rather than increasing the number of physical control elements. This has opened the door into hoisting systems for automatic loading and hoisting of ore as well as a means to achieve a comprehensive package of automated cage hoisting functions."

Jan 1, 1989

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

By Aalbert Zwijnenburg

One of problems connected with the use of gold/titania-based catalyst systems is the low yield in propene oxide (up to 2 wt %). It is shown that the low propene oxide yield is due to product inhibition. New options for propene epoxidation with hydrogen and oxygen are discussed. INTRODUCTION The direct gas-phase synthesis of propene oxide (PO), by the use of molecular oxygen, is still aimed for. Agbased catalysis is in principle possible, but selectivity at present is not promising. Highly dispersed gold on titanium containing catalysts show an extraordinary selectivity in the oxidation of propene to the corresponding epoxide (> 99 %), using a combination of H2 and O2 as oxidation mixture [1]. Additional studies of the epoxidation reaction have indicated several drawbacks of the Au/TiO2 catalyst. Firstly, the low conversion (1- 2 %) obtained under typical reaction conditions (atmospheric pressure, 323 - 423 K) cannot be increased by increasing the reaction temperature, because this leads to extensive by-product formation. Secondly, the low efficiency of hydrogen (relatively large amounts of water are formed) is hard to prevent. Finally, significant deactivation of Au/TiO2 catalysts within several hours on stream has been observed. Deactivation can be almost completely prevented by using dispersed TiO2 supports, such as TiO2/SiO2 and Titanium-Silicalite-1 (TS-1) [2]. In recent literature [2,3] a hydroperoxide-like intermediate has been proposed to be responsible for the selective epoxidation. This oxidising species is said to be formed over gold and subsequently used for epoxidation over the Ti-containing support. The support is responsible for the slow desorption of PO. One of the problems for future industrial application might be the low yield in propene oxide. Furthermore, the presence of minor amounts of by-products, not detected on lab-scale catalyst testing, might complicate the separation unit in an industrial process. The reason for the low PO yield over Au/TiO2-based catalysts will be discussed in this paper. Temperature Programmed Desorption (TPD) and micro-flow experiments have been carried out to study PO desorption and catalyst performance, respectively. A catalytic cycle is proposed together with its consequences for the maximum yield in PO. Finally, several process and catalyst options are discussed in view of potential future industrial application.

Oct 1, 2003

By Christoph Mueller

?Globalization and the impact on mine operations? is one of the themes of the 2003 annual CIM meeting. Global mining business in practice always means to act with local base material resources in order to reach the mining company?s global business goals. On the other hand these operations are characterized by cost pressure and cycling product prices. Driven by actual prices, local product markets and local production cost, one time one mine can be most efficient while under different circumstances another mine will be the most efficient producer for the same customer [PENSWICK, 2001]. Therefor in the future the most profitable mining companies will be those who have permanent ?real-time? control on their actual production cost level. Certain approaches are under way to provide reliable modeling tools for aiding mining companies in highly complex decision finding procedures. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory? [WIGDÉN, 2001]. Crucial to all these activities is the ability of getting reliable, just-in-time information from the entire mining production chain. As modern mining machinery today is controlled electronically and even already operated autonomously, the theoretical preconditions for the data acquisition is already fulfilled. But up to now, there was no way of cost effectively exchanging the process information with databases, simulation tools and other enterprise level software. Any data exchange problem had to be solved by individual and expensive software development projects. To solve these problems, the International Rock Excavation Data Exchange Standard (IREDES) was launched in 2000 by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. The standard?s technical architecture is flexible and open - also for future applications. It uses modern technology enabling easy data exchange with commercial databases as well as open on line networking.

May 1, 2003

By Ana Adé

The use of gold compounds in homogeneous catalysed organic reactions has been undervalued for many years due to the preconceived opinion that gold is an expensive and extremely chemically inert metal. However, recent reports have changed this assessment and gold salts in small amounts are known to display high catalytic activity.[1] Thus, it has been reported recently that anhydrous AuCl3 catalyses the formation of C-C and C-O bonds (usually mediated by hydrochloric and other protonic and Lewis acids).[2] Some examples include Michael type additions, selective cross cycloisomerisation/dimerisation of propargyl or allenyl ketones, benzannulation between o-alkynylbenzaldehides and alkynes or cyclisation of alkenyl furans. It is noteworthy that some of these reactions[2a] can be also catalysed by silver salts but with much lower yields. The 1,3-dipolar cycloaddition of nitrones to alkenes is a powerful synthetic method that has found numerous applications in the synthesis of a variety of carbon frameworks.[3] Several laboratories have focused on the development of Lewis acidic reagents to modulate the selectivity of the reaction.[4] Despite the extensive study performed, there are not many examples in which a metallic complex catalyses the dipolar cycloaddition. Most of these reactions require the presence of a metallic complex and nitrone in a 1:1 molar ratio. Recently, we have carried out stoichiometric reactions of the N-benzil-C(2-pyridil)nitrone, 1, with different dipolarophiles in the presence of zinc and silver compounds.[5] Apart from an increase of the reaction rate and the selective formation of one of the possible isomers, we have shown the formation of zinc and silver-nitrone complexes during the reaction, which behave as the intermediates in the cycloaddition process. As suggested by the results obtained with silver complexes, we decided to test gold derivatives (in the oxidation states of I and III). Interestingly, we have found that they can be used not only as stoichiometric reagents but they can also mediate these cycloadditions in catalytic amounts (5 to 10 mol % respect to the nitrone). Here we present the results on the 1,3-dipolar cycloaddition reaction of the N-benzil-C(2-pyridil)nitrone (2-PyBN), 1, and methylacrilate, 2, (Eq. 1) catalysed by gold(III) derivatives.

Oct 1, 2003