Search Documents

By A P. Powell

This paper deals with the power plant at Cassiar Asbestos Corporation Ltd., Cassiar, B.C. It discusses the units installed in the plant, the distribution of power and the costs involved. The efficiencies and economics of this power plant are considered to be somewhat better than average. Introduction C ASSIAR Asbestos Corporation's power plant had its inception in 1952 with a 15-by 15-ft. log cabin containing two International Harvester diesel generator sets of 50 kw. total generating capacity. Over the years, it has grown to its present size -an 80 by 82 ft. by 35-ft.-high rigid-frame Butler building housing eight 2,300-volt diesel generating sets, a 2,300-volt distributing switchboard, a 550-volt auxiliary panel, three air compressors, six heat exchangers and other related equipment. The units in the power plant, numbered according to their order of placement, are rated as shown in Table I. The total generating capacity of the plant is 3,673 kw. All of the generators are of the open vertical design except that on No. 7 engine,

Jan 1, 1965

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By D. J. McLaws

"Recent innovations in metal smelting technology utilize continuous oxygen-enriched smelting and converting processes which are capable of producing off-gases containing up to 60% SO2 or more. Other SO2 recovery processes, involving solvent absorption and steam or vacuum regeneration, can produce off-gases with SO2 concentrations nearing 100%.Processing of these high-concentration SO2 off-gases in conventional sulfuric acid plants can cause excessively high catalyst bed temperatures and poor SO2 conversion. In order to avoid these problems, a conventional acid plant design must dilute these high SO2 process gasses with dilution air in order to provide the required oxygen to effectively convert the SO2 and provide a heat sink (via the inert N2) such that the exothermic reaction, SO2 + ½ O2 ???SO3, does not exceed the temperature limit of the catalyst or the converter vessel.MECS, Inc. (MECS) has proven that a high SO2 feed gas design can be a viable option which can increase energy recovery, reduce energy consumption and potentially reduce capital costs."

Jan 1, 2014

By Joseph N. Bakambu

It is currently recognized by mining society that autonomously guided underground mining vehicles may greatly increase the efficiency of mining production and improve human safety. Recent results in mobile robotics, data fusion and sensor development provide a solid basis for solving the problems related to autonomous underground navigation. Recently developed commercial systems mostly rely on the infrastructure that is expensive and difficult to maintain. Guideless navigation in unstructured and harsh environment of underground mines is still a challenging task. In this paper, we describe an autonomous navigation system for an underground mining vehicle equipped with on-board dead reckoning, inertial and optical sensors. This system does not require any artificial infrastructure and is capable to guide the vehicle along the complex environment of interconnected underground drifts; it also ensures the detection of obstacles on the vehicle path. The user interface for monitoring and control is described and the results of laboratory tests and on-site experiments are presented. Work in progress addresses the system integration for real equipment, and the system upgrade, adding map-building and selflocalization capabilities .

May 1, 2002

By Baki Özüm

Early evaluations of Pasquia Hills kerogen shale deposits by Geological Survey of Canada, Saskatchewan Geological Survey, Manitoba Energy and Mines and Sun Oil Company, using modified Fischer Assay, Rock-Eval and other techniques, estimated recoverable reserves of about 2.6x109 barrels of oil in areas favorable for strip-mining; each metric ton of ore was determined to yield about 30 L to 50 L of shale oil remarkably high in aromatic compounds. Western Petrochemical Corp. (WPC) is holding two Oil Shale Exploration Permits covering about 76,635 hectares in the Pasquia Hills Region of eastern Saskatchewan and conducting a 15-corehole drilling program to determine stratigraphic correlation on both first and second white specks kerogen shale. In this program, correlation will be established between oil yield and oil quality, using different retort techniques, including modified Fischer Assay, steam retort and Rock-Eval. Results will lead to further resource evaluation and to a preliminary engineering design for a shale processing plant, including selection of retort process, upgrading of shale oil to petrochemical feedstock, hydrogen management, energy balance and evaluation of environmental impact.

May 1, 2002

By S. Pauly, U. Kühn, J. Eckert, I. Kaban, G. Wiehl, F. Silze

In the present work, the effect of Ga on the wetting behavior of the Cu-rich braze filler CuGa10 (wt.%) on the steel 304L was investigated. For this, the macroscopic and microscopic effects governing the wetting of pure Ga, pure Cu and CuGa10 alloy (wt.%) on the austenitic steel were analyzed and compared. Contact angle and surface tension measurements were carried out by means of the sessile drop technique and, in addition, the phase formation at the interface was determined. Pure liquid Ga spreads on 304L, which supposedly is related to the formation of intermetallic Fe-Ga phases growing into the liquid Ga. Depending on the annealing time, FeGa3 and Fe14.5Ga12 were identified. In contrast, CuGa10 as well as pure Cu show secondary wetting on the steel surface. Especially, liquid Cu prefers to spread laterally and vertically along the grain boundaries of the steel substrate. In spite of rather similar mechanisms, CuGa10 wets 304L steel at lower rate than pure Cu above the liquidus temperature.

Jan 1, 2014

By D. E. Salman, R. R. Maclachlan, R. J. Barclay

"There is a considerable resource of data for spherical charge cratering, both as single charges and in row-of-charge geometr(1). The data are. however, based on cratering performance to a single free planar surface.In practice. the more common circumstance involves an angular surf ace geometry. such as occurs at the toe of a bench or the wall of a stope. It is for the purpose of investigating this circumstance that the described test work was conducted.The test objectives were: (1) to observe the change in single-charge cratering performance between planesurface and angle geometry; (2) to identify the optimum performance of single charges cratering to a plane surface. cratering from a bench sub-grade position and cratering from a condition of zero sub-grade or stope wall geometry; and (3) to observe the performance of row-of-charges cratering to an angular surface at various row burials and spacing. The row charge burial and spacing dimensions were to be expressed in simple numerical multiples of single-charge depth-of-burial data."

Jan 1, 1981

By L. Voisin, K. Mühlenbrock

A new pyrometallurgical process is proposed for cleaning complex copper matte and for recovering copper from copper scrap containing lead. In the process, a given amount of pig iron is added to the complex material under a reducing condition to produce two or three liquid phases at the equilibrium, depending on the content of sulfur in system, of copper-rich and iron-rich alloys, and matte, respectively. The novel process is proposed based on the experimental results obtained by performing laboratory scale tests in an electrical furnace at 1473 K followed by a quenching method on the final stage. The samples obtained from the experiments were analyzed by using Atomic Absorption Spectroscopy (AAS), Inductively Couple Plasma (ICP) and Carbon Infrared Spectrometry (CIS) techniques. The results were discussed on the basis of the distribution of lead as impurity in the miscibility gap where equilibrated phases coexist. According to the mass balance calculations, the elimination of lead into the iron-rich alloy phase as a harmless and smaller deposit might be feasible and the process proposed for cleaning the complex matte would be promising.

Jan 1, 2014

By T. G. Joseph, G. W. Hansen

"This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sands material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 sq. yd. Consequences are manifested in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability.The objective of these considerations, as part of the Oil sands-Equipment Interaction Program (OsEIP), currently a joint venture between Syncrude Canada Ltd., James Progithin International (JPi) Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta, is to identify and provide feedback to the manufacturer and end user of adverse shovel-ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance."

Jan 1, 2002

By G. B. Harris

A new process for the recovery of copper and associated base metals from a polymetallic massive sulphide ore is described. The massive sulphide contains copper and especially nickel sulphide in a mineralogical form which negates both good recovery and high grades in concentrates using conventional flotation methods. Flotation concentrate processing and smelting from this ore is therefore probably not an economically viable option. Utilising the properties of high concentration chloride brines, a flow sheet has been developed and tested whereby the recovery of all of the metals and some of the power requirements for the plant itself can be derived from the ore. The new process overcomes the less-amenable-to-flotation ore characteristics, and provides the opportunity of economic processing in remote locations where the dependency on fossil fuels is both a logistical and an economic concern. The Ferguson Lake deposit of Starfield Resources in Nunavut, Canada, is the subject of this paper, which focuses on the leaching and copper recovery unit operations of the proposed flow sheet.

Jan 1, 2007

By R. V. Kumar, F. Tailoka

In order to use ZnO laden dust as a possible desulphurization reagent, it is important to evaluate thermodynamics of the Zn-O-S system. At temperatures greater than 1450 K, there is an uncertainty in the thermodynamic data for the reaction of zinc with sulfur to form Zinc sulfide. In this work, the standard free energy has been determined using an electrochemical cell: Pt, Mo, MoO2/YSZ/ZnO, ZnS, S02, Pt., between 1198 and 1602 K. AG° varies from -145,880 to -88,100 J (± 2500) , with a phase change to ZnS (g) by sublimation occurring between 1450 and 1460 K. This is supported by thermogravimetric analysis which shows about 80% weight loss in ZnS from 1273 to 1473 K. Feasibility reactions were also performed and confirmed that ZnS (g) is formed when ZnO reacts with FeS (1473 to 1653 K) or with Fe-Csat-S(1473-1673 K). There is therefore potential for the utilization of ZnO laden waste as an additional or alternative reagent for desulfurisation.

Jan 1, 2004

By Michel Carreau

Renewable assets have large upfront capital costs but minimal operating expenses over their lifetimes. In some instances, deals can be structured so that direct capital investment is feasible, with paybacks typically within 5-7 years. In others, the burden of renewable CAPEX must be removed in order to create an attractive alternative to fossil-fuel-fired generation. Hatch has designed and oversees the construction of a renewable installation, which is financed, owned and operated by a special-purpose entity. Renewable energy is then delivered to the mining company via a customized power purchase agreement at a price that is lower than the levelized cost of fossil fuels. In this way, the mining company removes the burden of the renewable energy CAPEX from its balance sheet, thus freeing up capital, decreasing risk, and making the predictable, lower cost of renewable power more attractive than the variable cost of fossil fuels. This paper presents the above business model and success stories of hybrid power at remote sites (wind and solar coupled with diesel engine).

Aug 1, 2013

Deformation is a critical indicator required to evaluate the structural safety, stability, and integrity. For example, the deformed shape of a building structure is a key parameter that needs to be measured and tracked during laboratory testing or post-disaster inspections. However, existing techniques used for the deformation measurement and tracking do not have all the desirable characteristics, such as: reliability, accuracy, low-cost and simplicity of tools installation. In order to address this issue, a novel method has been proposed in this study. The method consists on using the image processing technique to automatically measure and track the deformations of concentrically braced frame (CBF) structures. Accordingly, the critical points in a CBF structure are first identified and the topological configuration of the structure is retrieved. The points and topological configuration characterize the basic shape of the structure. In this way, the deformation of the structure can be determined by measuring and tracking these points and their topological configuration. To show its effectiveness, the proposed method has been tested against the manual deformation measurements.

Aug 1, 2013

By Tao Cheng

Previous research and applications in construction resource optimization have focused on tracking the location of material and equipment. There is a lack of studies on automated monitoring of the interaction between workers and equipment for safety purposes. This paper presents a new approach for measuring the safety performance of construction personnel particularly when they work in very close proximity to moving equipment as well as static hazards such as chemical and flammable substances. A method of generating hazardous zones according to the geometric and kinematic characteristics of the considered hazard is introduced. The spatio-temporal relationships between the hazardous zones and workers? positioning data collected by real-time location sensing technology are automatically analyzed. This approach has been validated in a controlled test bed environment that simulates a construction site. Results indicate that worker?s safety performance of selected activities can be automatically and reliably measured using the developed approach. Furthermore, a heat map is generated for visualizing proximity related issues in the test bed using the computed results.

Aug 1, 2013

By E. Faria

"The Santa Rita mine is located in north eastern part of Bahia in Brazil and is owned and operated by Mirabela Mineração do Brasil Ltda. Typical SABC circuit was designed as the preferred option for the 4.0 mtpa (500tph) to produce a P80 of 125um for flotation. Although the SAG was originally designed to operate with conventional radial pulp lifters, later it was fitted with Outotec’s Turbo Pulp Lifters – TPL (Latchireddi, 2005). The milling circuit commenced commissioning on the 24th of October 2009 and the milling circuit achieved the nameplate capacity within days. with small and relatively simple measures to rectify. Since commissioning, the SAG mill has been working in fully autogenous grinding (FAG) mode with no balls (in contrast to the estimated 10% ball charge) and has been consistently treated up to 650tph.This paper examines the comminution design process, the operating philosophies, start-up experiences, post commissioning optimization and future development works. An evaluation of mill performance relative to the design criteria for the project life to date is also included."

Jan 1, 2012

By A. J. Williams, W. H. A. Timm

"Lake Dufault Mines, Limited, is located north of Noranda, Quebec, and is a producer of copper and zinc concentrates. Various papers have been given on the mill design, construction and operation. 1, 2This paper is intended to describe the application of computer control to the Lake Dufault milling process. A brief history and description of the plant flowsheet will be given, followed by the reasons for installing the computer and the development of the program up to its present use. The success attained to date, comments on economic justification and future plans will also be given.HISTORY AND FLOWSHEETThe Lake Dufault ore body was discovered in September, 1961, and the mill commenced production during August, 1964. The rated capacity of 1,300 tons per day was reached by October 1, 1964. In milling the Lake Dufault ore, many metallurgical problems have been encountered, mainly due to wide and rapid variations in mill heads and oxidation of the massive sulphide ore. However, flexibility in plant layout and the incorporation of up-to-date instrumentation have facilitated its processing."

Jan 1, 1969

By J. R. Shore, F. G. M. Gillett, E. J. Zickar

"The addition of fines to rod mill feed has been employed at Inco Metals' Frood-Stobie Mill since 1973. The fines, which act as a ""lubricant"", causes an increase in the pulp fluidity and assists the flow of feed through the rod mill. Fines addition was one of the main factors which led to improved rod mill performance and the elimination of rod mill tangles.This paper outlines the testwork performed in evaluating the addition of fines, and summarizes the beneficial effects on rod mill grinding efficiency, throughput rates, power consumption and noise level. INTRODUCTIONFrood-Stobie Mill is situated within the Frood-Stobie mining complex, on the southern rim of the Sudbury Basin. The Mill commenced operations in November, 1967, and has since processed in excess of sixty-five million tons of ore. Minus 8-inch ore is delivered to the Mill's coarse ore bin by two surface conveyor belts from the Frood and Stobie Mines, while Little Stobie ore is transferred by underground conveyor and hoisted directly into the coarse ore bin a long with additional Stobie Mine ore."

Jan 1, 1981

By P. R. A. Andrews

"Garnet occurs in schists and gneisses in all provinces of Canada, all mainly in Quebec and Ontario. There is currently a renewed interest in exploration for economic sources of garnet for abrasive applications because of the inherent dangers from exposure to ground silica from sandblasting operations.High-quality garnet is used for lapping and grinding of glass and ceramics; for coated and bonded products such as sandpaper and cloth; and abrasive wheels for grinding and finishing various metals, woods, rubber and plastics. Low-quality garnet is used for cleaning and conditioning aluminum and other soft mewls, particularly by aircraft manufactures. Garnet may be added to grouting cements for oil-well drilling applications, and it has also been used for low- to medium-level radiation shielding. Garnet has been studied extensively by CANMET and its predecessor, Mines Branch, between 1917 and 1990. Twenty-nine studies relating 10 various aspects of beneficiation are presented and a review of the more important studies is presented. The information includes mineralogy, beneficiation methods, product sizes and analyses."

Jan 1, 1995

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By Edgar L. Horner

"The objectives of the Wabush Mines tailings stabilization program are to control dust Ii/t-off and to rehabilitate the disposal area. The evolution of the program started with test plots in 1970, these being continued and expanded upon through 1974. In 1976, a 35-acre vegetation field trial was attempted and failed, part of the failure being attributed to lack of adequate equipment. Subsequently, equipment was purchased and during the summer of 1979-80 extensive areas were treated. The program was also expanded to include the evaluation of chemical and water spray stabilization versus vegetation in areas where shorter-term control is required. In addition, during the summers of 1979-80, spruce bog material was spread over about 100 acres and seeded.The approach to reclamation by vegetation at Wabush is one of soil building. Work to this point indicates that iron ore tailings can be converted to a soil capable of supporting plants. Plans for the Wabush tailings disposal area should make dust lift-off from inactive tailings areas negligible within the next few years."

Jan 1, 1981