Search Documents

By J. P. Norrie

The presence of copper-bearing rocks in the Coppermine River area of Arctic Canada has long been known. Word of this was probably circulated along the Arctic and Hudson Bay coasts by the Eskimo, who no doubt traded articles made from native copper among themselves. It is not known whether any of these ever reached the southern shores of Hudson bay. The Indians, also, knew of the occurrence of copper here, as they served as guides to Hearne when he made a successful trip over land from Hudson bay to the Coppermine river. The possible commercial importance of these copper deposits was early appreciated by the Hudson's Bay Company, who on December 7th, 1770, despatched Samuel Hearne from Fort Prince of Wales, now Fort Churchill, to investigate them. He reached the then unnamed river at a point forty miles from its mouth on July 14th, 1771, and after surveying the river to its mouth and naming it the Coppermine, he retraced his steps to Fort Churchill by an overland route. Hearne's expedition was probably the most remarkable and arduous ever attempted in Arctic exploration, but the actual value derived from the trip was entirely out of proportion with the hardships he must have suffered. He verified the occurrence of native copper, but his astronomical and other observations were of little value. Until 1912 no concerted effort was made to obtain any definite information as to the geology and economic value of the Copper-mine deposits.

Jan 1, 1931

By E. E. Cudby

"FOLLOWING the Leduc discovery •by Imperial Oil in 1947, The California Standard Company began to acquire land in the area immediately west of Edmonton and in line with the Leduc reef trend (Figure 1).The California Standard Winter-burn Province No. 1 in Lsd. 10, Section 4, Township 53, Range 25, West 4th, which was spudded, on the basis of a seismic anomaly, in December, 1949, failed to find reef. This well was located on the eastern .edge of a large land block which California Standard and Imperial Oil had pooled as a joint venture, with California Standard a:s the operator (Figure 2).The culmination •of an extensive exploration and land aquisition programme was the drilling of the California Standard-Acheson Province No. 1 well .in Lsd. 13, Section 2, Township 53, Range 26, West 4th. On August 24th, 1950, a drill stem test was run in the D-3 zone which had been encountered at 4,969 feet, and a flow rate of 702 barrels per day •of 36° gravity oil was obtained. Just previously, Imperial Oil had completed a similar programme in the Stony Plain Reserve with the swabbing-in of Imperial Stony Plain No. 1. These two discoveries set off a drilling programme to determine the extent and value of the oil accumulation.Subsequent drilling of wells some successful .and others not by several other companies as well as California Standard bias, .to date, still left much to be determined as to the approximate delineation of the productive limits of the Ache-son-Stony Plain area. However, to August 31st, 1951, there were twenty-one D-3 producers north of the reserve and three in the Stony Plain Reserve."

Jan 1, 1952

"The QEMSCAN system is the third generation of automated mineral analysis systems that began with the QEM*SEM at CSIRO 30 years ago (Butcher et al. 2000). It is now a successful commercial instrument with 39 instruments in operation around the world. Back Scattered Electrons (BSE) and Energy Dispersive (EDS) X-Ray spectra are used to create digital mineral images with mineral identification occurring online. Low-count EDS spectra are used preferentially to BSE brightness, allowing minerals to be accurately identified by chemical composition. Individual minerals or groups of similar compositions are identified by comparison to a comprehensive mineral database incorporated into the QEMSCAN software. Optical mineralogy and Scanning Electron Microscopy is a metallurgists’ tool for determining the ore process mineralogy and delivering a better flowsheet. These techniques have limitations, provide limited information and sometimes fail to provide representative information. In contrast, QEMSCAN provides information on the nature and occurrence of all mineral species present plus the liberation characteristics, looking at thousands of particles in the sample presented. Some of the data presented includes:• Particle and grain sizes• Dominant mineral species• Particle shape• Calculated metal content• Density• Deportment of elements of interest between the mineral phases• Quantitative mineralogy• Mineral associations, locking and liberation• Textural relationships (particle images)It can also be used on concentrates, polished sections or drill core. This is a significant improvement in ore characterisation providing lithology, mineralogy, liberation, ore grade and porosity from a sample. Theoretical grade-recovery curves can be created to be mineralogically limited from QEMSCAN analysis which, when compared with metallurgical results, are valuable in evaluating whether liberation or chemical selectivity is driving flotation performance. A number of case study examples are given where the QEMSCAN had a significant bearing on future project development at an early stage of exploration and mine development."

Jan 1, 2012

By C. Piribauer, E. Feichtenhofer, A. McEneaney

"As part of a major diversification project, RHI AG, through its plant in Drogheda Ireland, has developed a Caustic Calcined Magnesium Oxide (CCM) for use in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry. In the course of the project, the company investigated the chemical and physical properties of a number of different Magnesia’s used in Co & Ni hydrometallurgy applications and has been able to determine the important parameters for a successful Magnesia for this application. A number of live plant trials have confirmed the results of this testwork and the company is now proceeding to produce this product in commercial quantities at Premier Periclase Ltd., the RHI AG plant in Drogheda, Ireland. This paper will outline the development work conducted by the company and highlight the important chemical and physical properties that make a successful CCM. Much of the research was conducted at the RHI Technology Centre in Leoben, Austria. In addition, a number of external laboratory studies were conducted on behalf of RHI AG. The result of this work has allowed the company to develop a Magnesia product with optimised properties for use in the Cobalt and Nickel hydrometallurgical extraction process.INTRODUCTION Premier Periclase is part of RHI AG, a globally operating supplier of refractory products, systems and services, headquartered in Vienna, Austria. The company produces Magnesia from seawater at its plant in Drogheda, Ireland. While the main focus is on production of refractory grade Dead Burned Magnesia for the steel industry, the plant also produces a number of different grades of Caustic Calcined Magnesia as well as Magnesium Hydroxide products. As part of a major project to diversify the company’s product base, the use of CCM in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry was investigated. One of the company’s highly reactive grades of Caustic Calcined Magnesia was found to be particularly suitable for this application. In an effort to understand what makes a successful Magnesia for hydrometallurgy the chemical and physical properties of different Magnesia’s used in Co & Ni hydrometallurgy were investigated. This paper and conference presentation outlines the findings of this process."

Jan 1, 2017

By Torsten Zeller

Due to the increasing worldwide demand for raw materials and the resulting rise in commodity prices more expensive processing that is able to utilize complex ores becomes economically viable. This and increasing ecological awareness is why the interest in recycling and urban mining is steadily growing in Germany. In addition to that; landfills do also contain elements, which were not targeted over the period, when they were being accumulated. Examples are rare earths, indium, gallium, cadmium, arsenic, selenium and tellurium. Also copper, zinc and lead, the target components of ancient mining, can be obtained due to more effective processing and smelting technologies. Funding by the German Federal Ministry for Education and Research, entitled "r³ ? Strategic Metals and Minerals ? Innovative Technologies for Resource Efficiency" also indicates the high level of strategic interest. It is against this background that the research project "Exploitation of the Raw Material Potential of Mining and Metallurgical Tips in Respect of Sustainability as Exemplified in the West Harz Mountains (ROBEHA)" has been implemented. A major concern of this project is the possible transfer of results to landfills in other areas. Therefore the development of an expert system based on the innovative processing methods and a method manual for urban mining are the central components of the investigation. This will provide an important contribution to the cost optimization of ensuing urban mining projects. To ensure the success of landfill mining projects it is necessary to record the composition and quality of the deposits accurately. Also the environmental impact caused by landfill mining and changes in the natural and cultural landscape will be considered in a multicriteria evaluation method. Depending on their origin the tips are divided into the categories mining, processing, and smelting. The content of a landfill and thus the economic potential in terms of urban mining is dependent on the type and composition of the deposits (host rock, gangue, and ore mineral), the available processing and smelting technology, and the target components at the time of mining. Zinc, for example, was not been processed until the 19th century, when it gained attention as being material of economic importance. After such knowledge about a landfill is obtained the decision for further investigations can be made. For a total of 158 landfills in the Harz Mountains, both the volume and the approximate contents of copper, zinc, and lead has been estimated for the different types of tips within past research projects. Based on the prices of the London Metal Exchange (LME) and a euro/dollar exchange rate of 0.76 (as of 03/05/2012) and assuming a minimum density of ? ? 1.5 t/m³ a average value of 1.6 billion ? in copper, zinc, and lead can be obtained. Although only these three metals are considered in this first estimate, it demonstrates the potential of landfill mining and the need for further research. KEYWORDS Urban Mining,

Aug 1, 2013

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By Owen Matthews

THE property of Cochenour Willans Gold Mines, Limited, is in Dome township, Red Lake area, northwestern Ontario, a hundred miles north of Kenora and close to the Manitoba border. 'Planes of Canadian Pacific Air Lines, Limited, serve the district daily, except Sundays, from Kenora, Ontario, and Lac du Bonnet, Manitoba, passengers being trans-ported from Winnipeg to Lac du Bonnet by car. Freight is handled by the Patricia Transportation Company. It is brought in from Hudson, Ontario, on the Canadian National railway, in summer by water and in winter by tractor trains over the frozen lakes. The first staking on the property was done during the 'rush' of 1926 and 1927 by William M. Cochenour, and on April 30th, 1928, a syndicate was formed, taking in claims of W. M. Cochenour and Dan Willans and H. G. Young. Surface trenching was carried on almost continuously until 1934. In October, 1932, Ventures Limited took an option on the property, and in December of that year they carried out an extensive diamond drilling programme, but considering the results did not justify further work, they relinquished the option. In July, 1934, further surface work was carried out under the supervision of W. P. Mackle and, on the strength of his report, Noah Timmins Incorporated took an option on the property and agreed to make an initial expenditure of $100,000 on development work. This was carried out under the direction of Hollinger Consolidated Gold Mines and included the sinking of a shaft to a depth of 165 feet, establishment of a level at the 150-foot horizon, and some 1,900 lineal feet of drifting and cross-cutting. The results obtained from this work were not considered of sufficient promise and the option was terminated in August, 1935. Mr. Cochenour then approached Alex Mackenzie and associates, and the present Company, Cochenour Willans Gold Mines, Limited, was organized on April 9th, 1936, and sufficient money was raised to continue operations. Under the direction of W. P. Mackle, the shaft was deepened and a second level was established at the 275-foot horizon; but, due to several adverse reports by outside engineers, it was found impossible to raise sufficient money to carry on the work and operations were suspended in December, 1937. In January, 1939, an agreement was entered into with Gold Eagle Gold Mines for the milling in their plant of some Cochenour ore. A total of 4,959 tons was treated, and the results were so encouraging that further finances were raised by C. A. Gentles & Company, of Toronto. Following further development in the mine, it was decided to erect a mill. Construction was started on September 1st and the mill was turned over on November 29th. The first gold brick was poured on December 23rd.

Jan 1, 1942

By W. T. Irvine

Introduction The property of the Britannia Mining and Smelting Company is on the east side of Howe sound, some twenty miles north of-Vancouver. The camp is served by two settlements, one at Britannia Mines townsite, approximately three miles from the water's edge at an altitude of 2,100 feet, the other at Britannia Beach, on Howe sound. The first discovery of copper ore on the property was made in 1888, but it was not until 1905 that production started. From that year until the end of 1944, production had totalled 732,414,420 pounds of copper and 261,126 ounces of gold from six orebodies, known as the Victoria, Empress, No. 5, Fairview, Bluff, and Jane. No. 8 orebody, with which this paper is concerned, was discovered in 1937 by diamond drilling from the 4100 level, some 300 feet above sea level. Development of this orebody to the end of 1944 had included the sinking of a shaft from the 4000 to the 5250 level, and a limited amount of stoping. This work has delimited the orebody from the 3800 to the 4950 level and has indicated upwards of 1,000,000 tons of copper-zinc-gold ore. It is planned to commence production in the near future, while continuing exploration of the orebody at depth.

Jan 1, 1946

By R. B. Hyde

"Severe drilling conditions and difficult mud problems are briefly out-lined as the major cost items in all production operations. The chief problems discussed are abnormal pressures, high temperature, trouble-some shales, and low rates of penetration. These problems have been eliminated or greatly reduced in many areas by• the proper application of recently developed drilling mud products and techniques. These severe problems and their solutions are discussed generally: the application of high-density weighting materials to overcome abnormal pressures; surfactant muds with sodium polyacrylate as a solution for deep and high-temperature drilling; shale control muds and new dispersants for severe shale problems; and low-solids emulsions and •extreme-pressure lubricants for greatly improved rates of penetration."

Jan 1, 1959

By John A. Legge Jr.

"ACCOMPANYING Alberta's great natural endowments of oil, wheat, scenery, fishing, and hunting is also a generous endowment of geophysical problems to plague the interpreting geophysicist. These problems — by no means unique to Alberta — are sufficiently numerous and outstanding to be of major concern in exploration. Some of them have been adequately solved, others are well on their way to being solved, and still others remain almost completely unsolved. Often a problem readily solvable in one area can be solved only with great difficulty in another. Many are closely allied with the geological conditions and require the best co¬ordinated efforts of the geologist and geophysicist for their solution.It is a fairly general practice to study rather carefully the geophysical characteristics of known producing reefs in order to obtain data on which to base an interpretation of unproven areas. This practice obviously has a very sound basis, for, as discoveries become more and more widespread in the Alberta basin, it is found that the variation' in geological conditions has a marked effect on the seismic results, as would be expected. By carrying this analysis over an area it is possible more and more to anticipate the geophysical picture which should be obtained in connection with reefing under the varying geological conditions. Another phase of this procedure, and one that has received less attention, though it is certainly of importance, is the analysis of the all too numerous failures. A study of these failures may be more fruitful than a study of the successes for it may indicate weaknesses of field procedure, computations, or in¬terpretation not particularly obvious in the discovery areas. These studies must not only include the geophysical characteristics of the observed `anomalies', but should also be coupled with a thorough geological study to ascertain whether some unanticipated geological condition is responsible for the erroneous geophysical interpretation."

Jan 1, 1953

By Robb. V. M., F. Walraven, L. J. Robb

"Abstract -The old Albert Silver Mine is a polymetallic deposit comprising concentrations of Cu­ Pb-Zn-Ag-U-F within a set of sub-parallel quartz-hematite veins which occur within the fine-grained apical phase of the 2050 Ma old A-type Bushveld granites. Mineralization occurs as an early pyrite­ chalcopyrite-arsenopyrite-galena-sphalerite-(argentiferous) tetrahedrite paragenesis followed by a later, more oxidized assemblage comprising chlorite-hematite-fluorite-pitchblende. Accumulation of metals appears to have taken place at the interface between a coarse-grained porphyritic granite and an overlying fine-grained phase: veins occur in the latter and represent leakage of magmatic fluids from the differentiated, water-saturated, subjacent granite.Mineralization processes in the Bushveld granites are believed to be related to long-lived circulation of dominantly magmatic fluids stimulated by the high heat productive capacity of the host rocks. Endo- and exogranitic tin-tungsten and base metal mineralization formed during an evolving hydrothermal system that lasted for several hundred million years, forming innumerable small- to medium­ scale polymetallic deposits. At the Albert Silver Mine, unroofing of the cover sequences at circa 1600 Mato 1700 Ma resulted in the incursion of lower-temperature, high-f02 meteoric fluids which remobilized the earlier sulfides and introduced the paragenetically late U-F mineralization ."

Jan 1, 1994

By D. A. Temple, G. O. John

Until recently, the approach to the problem of treating complex ores bas been to produce, insofar as is possible, mono-metal concentrates which are treated in traditional zinc, lead and copper smelting circuits, with the residues and by-products from some of these circuits being retreated for the recovery of contained values either by a separate residue treatment process or along with the primary feed to the appropriate circuit. The continued development of the Imperial Smelting Process, with its ability to treat poly-metal concentrates, calls for a re-examination of the traditional approach to this problem, and this the paper attempts to do. A survey of recent progress in the technical development of the process is made and a summary of current operational performance is included.

Jan 1, 1971

By A. van As, J. McGaughey, M. J. Mol, R. Tosen

Geotechnical monitoring is a key element of the successful management of a block cave mine. The interrelationships between production and various monitoring datasets are often not realized due to a lack of data integration and appropriate 3D visualization. Timely delivery of information to ensure best cave management practices is only possible with an integrated cave management system. At Rio Tinto, a state-of-the-art cave management system (CaveCAD) has been designed and developed in cooperation with Mira Geoscience to integrate and analyze vast datasets and report this as instructive information regarding the current \u201cstatus\u201d of the cave.

Jan 1, 2014

By K. W. Fritzsche

The prosperity of any nation depends, to a large extent, on its natural resources such as oil, coal, 'metal, timber, waterpower, and fertile soil. Each one of these resources forms the basis of a huge industry. The mining and smelting industry ranks among the first since it paves the way for a number of other industries. The mines and smelters provide a market for electric power, coal, timber, and agricultural products: other industries in turn provide a market for metals and non-metals. The real pioneering, however, is done by the prospector who goes into the wilderness to search for the ores from which the metals are to be extracted for the use of men. Prospecting is an interesting and fascinating occupation. There are many difficulties and hardships in the way but the lure of gold and the vision of finding an outcrop that may develop into a large bank account, within a reasonably short time, will urge the prospector forward. Thus, on the outskirts of this northern hemisphere hundreds of prospectors are searching and toiling and of whom nothing is known or heard until they reach civilization and announce a new discovery. Then a mad rush takes place and everybody who can afford to go will take a gamblers chance and plant stakes in the neighbourhood of the new discovery, or wherever an outcrop of mineralized rock can be found, with the hope of winning a fortune.

Jan 1, 1925

By G. S. Hume

THE Plains of east-central Alberta herein described embrace an area from Viking east to the Saskatchewan boundary and from North Saskatchewan river south to Coronation and Monitor (Figure 1). By far the greater part of this area is deeply drift-covered, and .outcrops of bedrock are relatively few and often widely separated. Within the area there are large morainal hills and others of considerable extent that superficially have all the characters of morainal hills but contain a core of bedrock. These latter, then, were hills when the ice sheet traversed the country and only have been modified by glacial agencies. In many places on them, the drift is but a thin veneer, as is certainly the case in part of the Neutral hills (Figure 2) northeast of Coronation and north of Monitor. In other cases, however, as in the Blackfoot hills, southwest of Lloydminster, the drift is sufficiently thick to conceal practically all the bedrock and in many places no information is available as to whether a bedrock core, representing a pre-glacial hill, is present. There is no question, however, that the larger river valleys, as for example those of the North Saskatchewan and Battle rivers, are in part at least pre-glacial. Proof of this can be demonstrated in many places, because obviously the valleys must have been present in pre-glacial times to allow glacial deposits to have accumulated in them. It is also known that inter-glacial deposits occur. At one locality in Battle River valley, in sec. 30, tp. 45, range 2, west of the 4th mer., the following section occurs( l ): 15 feet of boulder clay with granite and other boulders. 56 feet of stratified sands, clays, and gravels containing pebbles of Precambrian rocks and fresh-water shells. From this it is apparent that the 56 feet of stratified sands, clays, and gravels must have derived their Precambrian pebbles from a previous glaciation of which the overlying boulder clay represents another ice advance in this area. Thus, although the river valleys contain glacial and interglacial deposits, they have not been filled by them to such an extent that the drainage has been diverted, and in many places, especially in the case of Battle river and some smaller streams, the size of the valley is altogether out of proportion to the size of the stream it now contains.

Jan 1, 1937

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By S. A. Vazhnov, A. G. Kalimov, A. A. Potienko

In this paper we describe a mathematical model of the magnetic field and magnetohydrodynamic processes simulation in aluminum reduction cells developed in St. Petersburg State Polytechnic University, Russia. The model includes: (a) calculation of the currents in the busbar system and inside the aluminum cell construction elements including cathode and anode structures, aluminum and electrolyte layers; (b) magnetic field simulation using the integral equation method; ( c) investigation of the magnetohydrodynamic characteristics on the basis of a shallow-water approach. The developed model was used to investigate operational characteristics of the different industrial aluminum cells. Calculated magnetic field distributions and MHD stability parameters were compared with the available experimental information; the comparison demonstrated a reasonably good agreement.

Jan 1, 2006

By A. Hekmat-Ardakan

Conventional hypereutectic Al-Si alloys such as A390 are used principally for the casting of components used in wear applications requiring abrasive resistance such as in engine or compressor blocks. A comprehensive study was undertaken to investigate the potential of improving the mechanical properties of these alloys by the addition of magnesium. A thorough thermodynamic study of the effect of the addition of Mg to the conventional A390 alloy showed that Mg2Si starts to form as a primary phase at 4.2% Mg as well as in the products of the binary and ternary eutectic reactions forming the matrix. Experiments were carried out in producing castings with different cooling and solidification rates of alloys with up to 10% Mg. Mg additions were found to increase the hardness over the as cast alloy due to solid solution strengthening. Also, T6 heat treatment greatly improved the tensile properties of these alloy compositions due to the strengthening effect of the theta-Al2Cu phase. The elongation of these alloys generally decreases marginally with Mg content. The most significant property improvement of the alloys with higher Mg content is the substantial increase in wear resistance. This is attributed to the dispersion of smaller particles of Mg2Si and their coherence with the matrix as compared to the large Si particles in the conventional alloy. A new rheoforming process for A390 is presented that improves the processing of the semi-solid slurry. Structure modification elements were also added to refine the primary and eutectic silicon greatly improving the processing of the semi-solid slurry.

Jan 1, 2011

By A. E. Cameron

The curve of coal production in Nova Scotia over the past forty years shows a definite maximum reached in 1913. Continued production to this maximum will require a greater tonnage per man-day, and this means there cannot be any increase in total man power used in the operations. There are still large reserves of coal but much of it will require washing or beneficiating to make a usable product. By-product recovery based on the present product ion is relatively satisfactory. Further development of secondary industries requires adequate markets for the bulk materials produced by the processing. It also requires access to other raw materials as well as markets for the principal product of the operations. Scientific investigation and research are needed to prove the quantity and value of lower grade or poorer quality coals, and methods for their recovery and utilization. Economics of further processing of present and future production must be investigated beforehand, if a successful development is to be assured. Such development cannot be expected largely to replace present markets. Production of coal for genera l use must continue to form the major function of the coal industry of the Province. Costs per ton must decrease, or subsidies or other assistance must increase, if the industry is to survive. Costs of investigation and research and costs of capital outlay for further development muse be met.

Jan 1, 1944

By K. S. Raja, F. Battick, B. Pesic

"CeO2 doped with lower valence cations, such as Y3+, Sm3+, Gd3+ etc. is considered as electrolyte material for low temperature SOFC. Doping introduces additional oxygen vacancies and improves ionic conductivity. This work describes the preparation of yttria-calcia doped-ceria precursor material, its sintering in DC and AC field methods, and characterization of sintered electrolytes with respect to the ionic conductivity. Doped precursor materials were prepared by a controlled co-precipitation process. Sintering of prepared, pelletized particulates was carried out using three different methods such as: 1) conventional; 2) spark plasma sintering; and 3) an alternating current field at 1125°C (AC assisted sintering). The mechanism involved in the conductivity improvement as a function of defect density, grain boundary area and phase stability will be discussed. INTRODUCTIONThe performance of SOFCs depends highly on the properties of materials. Subtle variations in the composition, microstructure, or density of SOFC components can considerably alter the power output capabilities of fuel cells. Early SOFCs utilized zirconia based electrolytes but efforts in lowering the operating temperatures of SOFCs have prompted investigations into several other oxygen ion conductors – often modified with dopants to either promote the formation of oxygen vacancies or to stabilize a vacancy rich high temperature phase – such as bismuth oxide, lanthanum gallate, and ceria.The transport of oxygen ions through the electrolyte first begins with diffusion into the material. While this is generally a surface kinetics phenomenon, it is safe to say that it is highly dependent on oxygen pressure and vacancy gradients. The role of the cathode in SOFCs is to reduce oxygen at the electrolyte surface creating an O2– ion gradient which induces permeation into the material. Once inside and under the influence of a potential field, O2– ions migrate by a vacancy hopping mechanism, Catlow, C.R.A. (1990), effectively exchanging positions throughout the matrix until they reach the anode and react, thus leaving the matrix."

Jan 1, 2012